PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com HIGH FREQUENCY ULTRA PERFORMANCE LOW POWER JITTER OSCILLATOR 156.250000MHz-156.261718MHz SERIES „HFUPLJO“ FEATURES APPLICATIONS + + + + + + + + + + + SATA, SAS, Ethernet, 10Gb Ethernet, XAUI + Computing, storage, networking, telecom, industrial control, + etc. Ultra Performance Oscillator for Low Cost Ultra low phase jitter 100% pin-to-pin drop-in replacement to quartz and MEMS based XO Low Power Consumption Excellent long time reliability Very tight frequency stability as low as ±10 ppm Outstanding long term aging of ±5ppm after 10 years LVCMOS/LVTTL compatible output Standard housings: 2.5x2.0; 3.2x2.5; 5.0x3.2; 7.0x5.0 mm Pb-free, RoHS and REACH compliant / MSL1@260°C GENERAL DATA[1] PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT CONDITION FREQUENCY RANGE Output Frequency Range f 156.250000, 156.253906 156.257800, 156.257812 156.261718 MHz FREQUENCY STABILITY AND AGING Frequency Stability First year Aging F_stab F_aging 10-year Aging -10 – +10 PPM Inclusive of Initial tolerance at 25 °C, and variations over -20 – +20 PPM operating temperature, rated power supply voltage and load -25 – +25 PPM -50 – +50 PPM -1.5 – +1.5 PPM 25°C -5 – +5 PPM 25°C -20 – +70 °C Extended Commercial OPERATING TEMPERATURE RANGE Operating Temperature Range T_use -40 – +85 °C Industrial Storage Temperature Range T_stor -55 – +125 °C Storage VDD 1.71 1.8 1.89 V Supply voltages between 2.5V and 3.3V can be supported. 2.25 2.5 2.75 V Contact PETERMANN-TECHNIK for additional information. 2.52 2.8 3.08 V 2.97 3.3 3.63 V – 31 33 mA No load condition, VDD = 2.5V, 2.8V or 3.3V – 29 31 mA No load condition, VDD = 1.8V – – 31 mA VDD = 2.5V, 2.8V or 3.3V, OE = GND, output is pulled down – – 30 mA VDD = 1.8 V. OE = GND, output is pulled down – – 70 µA VDD = 2.5V, 2.8V or 3.3V, ST = GND, output is pulled down – – 10 µA VDD = 1.8 V. ST = GND, output is pulled down SUPPLY VOLTAGE AND CURRENT CONSUMPTION Supply Voltage Current Consumption OE Disable Current Standby Current IDD I_OD I_std Notes: 1. All electrical specifications in the above table are specified with 15 pF output load at default drive strength and for all VDD(s) unless otherwise stated. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 1 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com GENERAL DATA[1] (continued) PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT DC 45 – 55 % Tr, Tf – 1.2 2 ns 15 pF load, 10% - 90% VDD – 2.2 – ns 30 pF load, 10% - 90% VDD – 3.4 – ns 45 pF load, 10% - 90% VDD CONDITION LVCMOS OUTPUT CHARACTERISTICS Duty Cycle Rise/Fall Time Output Voltage High VOH 90% – – VDD IOH = -6 mA, IOL = 6 mA, (VDD = 3.3V, 2.8V, 2.5V) Output Voltage Low VOL – – 10% VDD IOL = 3 mA, (VDD = 1.8V) Input Voltage High VIH 70% – – VDD Pin 1, OE or ST Input Voltage Low VIL – – 30% VDD Pin 1, OE or ST Input Pull-up Impedance Z_in – 100 250 kΩ Pin 1, OE logic high or logic low, or ST logic high 2 – – MΩ Pin 1, ST logic low T_start – 7 10 ms Measured from the time VDD reaches its rated minimum value INPUT CHARACTERISTICS STARTUP AND RESUME TIMING Startup Time OE Enable/Disable Time T_oe – – 150 ns T_resume – 6 10 ms In standby mode, measured from the time ST pin crosses 50% threshold. Refer to Figure 5. RMS Period Jitter T_jitt – 1.5 2 ps VDD = 2.5V, 2.8V or 3.3V RMS Phase Jitter (random) T_phj Resume Time JITTER – 2 3 ps VDD = 1.8V – 0.25 0.3 ps IEEE802.3-2005 10GbE jitter measurement specifications EXCELLENT RELIABILITY DATA MTBF 500 million hours Shock Resistance: 10.000 g Vibration Resistance: 70 g Notes: 1. All electrical specifications in the above table are specified with 15 pF output load and for all VDD(s) unless otherwise stated. 2. Contact PETERMANN-TECHNIK for custom drive strength to drive higher or multiple load, or for EMI reduction. PIN DESCRIPTION PIN 1 SYMBOL TOP VIEW FUNCTIONALITY Output Enable H or Open[3]: specified frequency output L: output is high impedance. Only output driver is disabled. Standby H or Open[3]: specified frequency output L: output is low (weak pull down). Device goes to sleep mode. Supply current reduces to I_std. OE/ ST 2 GND Power Electrical ground[4] 3 OUT Output Oscillator output 4 VDD Power Power supply voltage[4] OE/ST 1 4 VDD GND 2 3 OUT Notes: 3. A pull-up resistor of <10 kΩ between OE/ ST pin and VDD is recommended in high noise environment. 4. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 2 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TEST CIRCUIT AND WAVEFORM[5, 6] FIGURE 1. TEST CIRCUIT FIGURE 2. WAVEFORM Vout Vdd 3 4 Power Supply Test Point tf 90%Vdd 0.1µF 15pF (including probe and fixture capacitance) 2 1 tr 50% 10%Vdd High Pulse (TH) Low Pulse (TL) Period Vdd OE/ST Function 1kΩ TIMING DIAGRAMS [7,8] FIGURE 3. STARTUP TIMING (OE/ST MODE) 90%Vdd, 2.5/2.8/3.3V devices VDD 95%Vdd, 1.8V devices Pin 4 Voltage FIGURE 4. STANDBY RESUME TIMING (ST MODE ONLY) 50%VDD No Glitch first cycle VDD ST Voltage T_resume T_start CLK Output T_start: Time to start from power-off FIGURE 5. OE ENABLE TIMING (OE MODE ONLY) CLK Output T_resume: Time to resume from ST FIGURE 6. OE DISABLE TIMING (OE MODE ONLY) VDD 50%VDD VDD OE Voltage OE Voltage 50%VDD T_OE CLK Output CLK Output T_OE HZ T_OE: Time to re-enable the clock output T_OE: Time to put the output drive in High Z mode Notes: 5. Duty Cycle is computed as Duty Cycle = TH/Period. 6. HFUPLJO supports the configurable duty cycle feature. For custom duty cycle at any given frequency, contact PETERMANN-TECHNIK. 7. HFUPLJO supports no runt pulses and no glitches during startup or resume. 8. HFUPLJO supports gated output which is accurate within rated frequency stability from the first cycle. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 3 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) [9] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 2.7X 2.4 X 0.75 MM (100% compatible with 2.5 x 2. 0 mm footprint) #1 1.9 1.00 #3 #3 #1 #2 #2 1.0 1.1 1.5 #4 0.5 2.7±0.05 2.4±0.05 #4 1.1 0.75±0.05 0.85 RECOMMENDED LAND PATTERN (UNIT:MM) [9] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 3.2 X 2.5 X 0.75 MM #1 2.2 2.1 #3 #3 #1 #2 #2 1.2 0.9 1.9 #4 0.7 3.2±0.05 2.5±0.05 #4 1.4 0.75±0.05 0.9 RECOMMENDED LAND PATTERN (UNIT:MM) [9] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 5.0 X 3.2 X 0.75 MM #3 #1 #2 #2 1.1 1.6 2.2 #4 1.15 1.5 0.75±0.05 #1 2.54 2.39 #3 0.8 5.0±0.05 3.2±0.05 #4 Note: 9. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 4 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) [9] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 7.0 X 5.0 X 0.90 MM #3 #1 #2 3.81 #4 #2 2.0 1.1 1.4 2.2 0.90±0.10 #1 5.08 5.08 #3 2.6 7.0±0.05 5.0±0.05 #4 REFLOW SOLDER PROFILE Note: 9. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 5 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com ORDERING INFORMATION OSCILLATOR FAMILY SUPPLY VOLTAGE “18“ “25“ “28“ “33“ HFUPLJO for 1.8V for 2.5V for 2.8V for 3.3V TEMPERATURE RANGE FREQUENCY 156.250000MHz 156.253906MHz 156.257800MHz 156.257812MHz 156.261718MHz “M” for -20 +70°C “W” for -40 +85°C HFUPLJO 33-2724-E-10-M-156.25000MHz-T PACKING METHOD FREQUENCY STABILITY “B” for BULKS or TUBES “T” for TAPE & REEL “10” for ±10 PPM “20” for ±20 PPM “25” for ±25 PPM “50” for ±50 PPM PACKAGE SIZE FEATURE PIN 1 “2724” for 2.7 X 2.4 mm “3225” for 3.2 X 2.5 mm “5032” for 5.0 X 3.2 mm “7050” for 7.0 X 5.0 mm “E” for OUTPUT ENABLE “S” for STANDBY Note: 10. Contact PETERMANN-TECHNIK for custom drive strength to drive higher or multiple load, or for EMI reduction. EXAMPLE: HFUPLJO33-2724-E-10-M156.25000MHz-T PLEASE INDICATE YOUR REQUIRED PARAMETERS SAMPLES ARE AVAILABLE WITHIN A SHORT DELIVERY PERIOD! CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 6 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com PREMIUM QUALITY BY PETERMANN-TECHNIK OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH. THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS. © PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 7 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014