IM831 Series 16 A

MEMS Oscillator, -55°C to +125°C, LVCMOS/HCMOS Compatible, 119.342001 MHz to 137.000MHz
Features:
Typical Applications:












MEMS Technology
Direct pin to pin drop-in replacement for industry-standard packages
Ultra-low phase jitter: 0.5 pSec (12 kHz to 20 MHz)
LVCMOS/HCMOS Compatible Output
Industry-standard package 2.0 x1.6, 2.5 x 2.0, 3.2 x 2.5, and 5.0 x 3.2 mm x mm
Pb-free, RoHS and REACH compliant
Fast delivery times
IM831 Series
Fibre Channel
Server and Storage
GPON, EPON
100M / 1G /10G Ethernet
Ruggedized equipment in
harsh operating environment
Electronic Specifications:
Frequency Range
Frequency Stability
Operating Temperature
Supply Voltage (Vdd) ±10%
Current Consumption
OE Disable Current
Standby Current
Waveform Output
Symmetry
Rise / Fall Time
Logic “1”
Logic “0”
Input Voltage High
119.342001 MHz to 137.000MHz
See Part Number Guide
-55°C of +125°C
See Part Number Guide
6.2 mA typ./ 8.0 mA max
5.4 mA typ./ 7.0 mA max
4.9 mA typ./ 6.0 mA max
4.7 mA max
4.5 mA max
2.6 µA typ./ 8.5 µA max
1.4 µA typ./ 5.5 µA max
0.6 µA typ./ 4.0 µA max
LVCMOS/HCMOS
45%/55%
1.0 nSec typ./ 2.0 nSec max
1.3 nSec typ./ 2.5 nSec max
90% of Vdd min
10% of Vdd max
70% of Vdd min
Input Voltage Low
Input Pull-up Impedance
30% of Vdd max
50 kΩ min/ 87 kΩ typ./150 kΩ max,
2.0 MΩ min
Startup Time
Enable/Disable Time
5 mSec max
130 nSec max
Resume Time
RMS Period Time
5 mSec max
1.6 pSec typ./ 2.5 pSec max
1.8 pSec typ./ 3.0 pSec max
12 pSec typ./ 20 psec max
14 pSec typ./ 25 pSec max
0.5 pSec typ./ 0.8 pSec max
1.3 pSec typ./ 2.0 pSec max,
Peak-to-Peak Period Jitter
RMS Period Time (random)
Inclusive of Operating Temperature Range, Load, Voltage, and Aging
No load condition, f = 125 MHz, Vdd = +2.8 V, +3.0 V or +3.3 V
No load condition, f = 125 MHz, Vdd = +2.5 V
No load condition, f = 125 MHz, Vdd = +1.8 V
Vdd = +2.5 V, or +3.3 V, OE = Low, output is high Z state
Vdd = +1.8 V, OE = Low, output is high Z state
Vdd = +2.8 V to 3.3 V, ST = low
Vdd = +2.5 V, ST = Low
Vdd = +1.8 V, ST = Low
50% of waveform
Vdd = +2.5 V, +2.8 V, 3.0 V or 3.3 V from 20% to 80% of waveform
Vdd = +1.8 V, from 20% to 80% of waveform
Pin 1, OE or ST
Pin 1, OE or ST
Pin 1, OE logic high or logic low, or ST logic high
Pin 1, ST logic low
Measured from the time Vdd reaches its rated minimum values
F = 119.342001 MHz. For other frequencies, T_oe = 100 ns + 3 *
clock periods
Measured from the time ST pin crosses 50% threshold.
F = 125 MHz, Vdd = +2.5 V, +2.8 V, +3.0 V or +3.3 V
F = 125 MHz, Vdd = +1.8 V
F = 125 MHz, Vdd = +2.5 V, +2.8 V, +3.0 V or +3.3 V
F = 125 MHz, Vdd = +1.8 V
F = 125 MHz, Integration bandwidth = 900 kHz to 7.5 MHz
F = 125 MHz, Integration bandwidth = 12.0 kHz to 20.0 MHz
Notes:

All min and max limits are specified over temperature and rated operating voltage with 15pF output unless otherwise stated.

Typical values are at +25ºC and nominal supply voltage.
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev 01/30/16_A
Page 1 of 9
MEMS Oscillator, -55°C to +125°C, LVCMOS/HCMOS Compatible, 119.342001 MHz to 137.000MHz
IM831 Series
Ordering Information:
Part Number Guide
Input
Voltage
Packages
IM831B – 5.0 x 3.2
IM831C – 3.2 x 2.5
IM831D – 2.5 x 2.0
IM831E – 2.0 x 1.6
1 = +1.8 V
6 = +2.5 V
2 = +2.8 V
7 = +3.0 V
3 = +3.3 V
Operating
Temperature
Output Drive
Strength
7 = -55ºC to +125ºC
- = Default
(see tables 2
through 6)
Stability
(ppm)
F = ±20
A = ±25
Z = ±30
B = ±50
Select Function
H = Tri-State
S = Standby
O = N/C
Frequency
-
Frequency
Sample Part Number: IM831C-67-FS-130.0000 MHz
This 130.0000 MHz oscillator in a 3.2 x 2.5 package with stability ±20 ppm from -55ºC to +125ºC using a supply voltage of +2.5 V. The Output Drive
Strength (Rise and Fall Time) is 0.96 nSec per Table 2 with 15 pF load. With Pin 1 function is Standby
Sample Part Number: IM831B-17-AS-115.0000 MHz
This 115.0000 MHz oscillator in a 5.0 x 3.2 package with stability ±25 ppm from -55ºC to +125ºC using a supply voltage of +1.8 V. The Output Drive
Strength (Rise and Fall Time) is 1.00 nSec per Table 1 with 15 pF load. With Pin 1 function is Tri-State
Notes:

Not all options are available at all frequencies and temperatures ranges.

Please consult with sales department for any other parameters or options.

Oscillator specification subject to change without notice.
Absolute Maximum Limits
Storage Temperature
Supply Voltage (Vdd)
Electrostatic Discharge
Solder Temperature (follow standard Pb free soldering guidelines)
Junction Temperature
Test Circuit
-65ºC to +150ºC
-0.5 VDC to 4.0 VDC
2000 V max
260ºC max
150ºC max
Waveform
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev 01/30/16_A
Page 2 of 9
MEMS Oscillator, -55°C to +125°C, LVCMOS/HCMOS Compatible, 119.342001 MHz to 137.000MHz
IM831 Series
Performance Plots:
Figure 1: Idd vs Frequency
Figure 2: Frequency vs Temperature
Figure 3: RMS Period Jitter vs Frequency
Figure 4: Duty Cycle vs Frequency
Figure 5: 20% to 80% Rise Time vs Temperature
Figure 6: 20% to 80% Rise Time vs Temperature
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev 01/30/16_A
Page 3 of 9
MEMS Oscillator, -55°C to +125°C, LVCMOS/HCMOS Compatible, 119.342001 MHz to 137.000MHz
IM831 Series
Performance Plots (Cont.)
Figure 7: RMS Integrated Phase Jitter Random
(12 kHz to 20 MHz) vs Frequency
Figure 8: RMS Integrated Phase Jitter Random
(900 kHz to 20 MHz) vs Frequency
Environmental Specifications:
Environmental Compliance
Parameter
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL Level 1 at +260ºC
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Pb Free Solder Reflow Profile
Units are backward compatible with +240ºC reflow processes
Ts max to TL (Ramp-up Rate)
Preheat
Temperature min (Ts min)
Temperature typ (Ts typ)
Temperature max (Ts max)
Time (Ts)
Ramp-up Tate (TL to Tp
Time Maintained Above
Temperature (TL)
Time (TL)
Peak Temperature (Tp)
Time within 5ºC to Peak
Temperature (Tp)
Ramp-down Rate
Tune 25ºC to Peak
Temperature
Moisture Sensitivity Level
(MSL)
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
3ºC / second max
150ºC
175ºC
200ºC
60 to180 seconds
3ºC / second max
217ºC
60 to 150 seconds
260ºC max for seconds
20 to 40 seconds
6ºC / second max
8 minute max
Level 1
Rev 01/30/16_A
Page 4 of 9
MEMS Oscillator, -55°C to +125°C, LVCMOS/HCMOS Compatible, 119.342001 MHz to 137.000MHz
IM831 Series
Pin Functionally
Pin Description
Pin
Symbol
1
OE
Tri-state
ST
Standby
N/C
No Connect
Functionality
High or Open = specified frequency output
Low = Output is high impedance, only output is disabled.
High or Open = specified frequency output.
Low = Output is low .Device goes to sleep mode. Supply current
reduces to standby current.
Any voltage between 0.0 V to Vdd or Open = specified frequency
output
Pin 1 has no functiion
Electrical ground
Oscillator output
Power supply voltage
Pin Assignments
OE
ST 1
N/C
Vdd
3
OUT
Top View
2
GND
Power
3
Out
Output
4
Vdd
Power
Notes:
1. In OE or ST mode, a pull-up resistor of 10.0 kΩ or less is recommended if Pin 1 is not externally
driven. If Pin 1 needs to be left floating, use the NC option.
2. A capacitor of value 0.1 µF or higher between Pin 4 (Vdd) and Pin 1 (GND) is required.
Pin 1 Configuration Options (OE, or
4
GND 2
, or NC)
Pin 1 of the IM831 can be factory-programmed to support three modes: Output Enable (OE), Standby (ST) or No Connect (NC).
Output Enable (OE) Mode
In the OE mode, applying logic Low to the OE pin only disables the output driver and puts it in Hi-Z mode. The core of the device
continues to operate normally. Power consumption is reduced due to the inactivity of the output. When the OE pin is pulled High, the
output is typically enabled in <1 µSec.
Standby
Mode
In the ST mode, a device enters into the standby mode when Pin 1 pulled Low. All internal circuits of the device are turned off. The
current is reduced to a standby current, typically in the range of a few µA. When ST is pulled High, the device goes through the
“resume” process, which can take up to 5 mSec.
No Connect (NC) Mode
In the NC mode, the device always operates in its normal mode and outputs the specified frequency regardless of the logic level
on Pin 1.
Table 1 below summarizes the key relevant parameters in the operation of the device in OE, ST, or NC mode.
Parameters
Active current 20.0 MHz (max +1.80 VDC)
OE disable current (max +1.80 VDC)
Standby current (typical +1.80 VDC)
OE enable time at 20.0 MHz (max)
Resume time from standby
(max, all frequency)
Output driver in OE disable/standby mode
Table 1 OE vs.
OE
6.0 mA
4.0 mA
N/A
200 nSec
ST
6.0 mA
N/A
0.6 µA
N/A
NC
6.0 mA
N/A
N/A
N/A
N/A
5 mSec
N/A
High Z
vs. NC
N/A
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev 01/30/16_A
Page 5 of 9
MEMS Oscillator, -55°C to +125°C, LVCMOS/HCMOS Compatible, 119.342001 MHz to 137.000MHz
IM831 Series
Timing Diagrams
Figure 9: Startup Timing (OE/
Mode)
Figure 11: OE Enable Timing (OE Mode Only)
Figure 10: Standby Resume Timing (
Mode Only)
Figure 12: OE Disable Timing (OE Mode Only)
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev 01/30/16_A
Page 6 of 9
MEMS Oscillator, -55°C to +125°C, LVCMOS/HCMOS Compatible, 119.342001 MHz to 137.000MHz
IM831 Series
Selectable Drive Strength Option
Rise/Fall Time (20% to 80%) vs CLOAD Tables
Rise/Fall Time Typ (nS)
Drive Strength
5 pF
15 pF
(CLOAD)
T
0.93
N/A
E
0.78
N/A
U
0.70
1.48
- = Default
0.65
1.30
30 pF
N/A
N/A
N/A
N/A
Table 1 Vdd = 1.8 V Rise/Fall time for Specific CLOAD
Rise/Fall Time Typ (nS)
Drive Strength
5 pF
15 pF
(CLOAD)
R
1.29
N/A
B
0.97
N/A
T
0.55
1.12
U
0.44
1.00
- = Default
0.34
0.88
F
0.29
0.81
30 pF
N/A
N/A
N/A
N/A
N/A
1.48
Table 3 Vdd = 2.8 V Rise/Fall time for Specific CLOAD
Rise/Fall Time Typ (nS)
Drive Strength
5 pF
15 pF
(CLOAD)
R
1.16
N/A
B
0.81
N/A
- = Default
0.46
1.00
E
0.33
0.87
U
0.28
0.79
F
0.25
0.72
Rise/Fall Time Typ (nS)
Drive Strength
5 pF
15 pF
(CLOAD)
R
1.45
N/A
B
1.09
N/A
T
0.62
1.28
E
0.54
1.00
- = Default
0.43
0.96
F
0.34
0.88
30 pF
N/A
N/A
N/A
N/A
N/A
N/A
Table 2 Vdd = 2.5 V Rise/Fall time for Specific CLOAD
Rise/Fall Time Typ (nS)
Drive Strength
5 pF
15 pF
(CLOAD)
R
1.22
N/A
B
0.89
N/A
- = Default
0.51
1.00
E
0.38
0.92
U
0.30
0.83
F
0.27
0.76
30 pF
N/A
N/A
N/A
N/A
N/A
1.39
Table 4 Vdd= 3.0 V Rise/Fall time for Specific CLOAD
30 pF
N/A
N/A
N/A
N/A
1.46
1.31
Table 5 Vdd = 3.3 V Rise/Fall time for Specific CLOAD
Note:

“N/A” in Table 1 to Table 5 indicates that the resulting rise/fall time from respective combination of the drive strength and output load does not
provide rail-to-rail swing and is not available.
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev 01/30/16_A
Page 7 of 9
IM831 Series
MEMS Oscillator, -55°C to +125°C, LVCMOS/HCMOS Compatible, 119.342001 MHz to 137.000MHz
Mechanical Details:
Package Dimensions and Suggest Land Pattern
Option E: 2.00 x 1.60 x 0.80 Package
Suggested Land Pattern
2.00 ±0.05
1.23
3
Marking
1.60 ±0.05 0.93
1.50
4
Bottom View
1
2
0.80 max
0.48
1.20
0.8
0.68
0.9
Suggested Land Pattern
Option D: 2.50 x 2.00 x 0.80 Package
1.00
2.50 ±0.05
1.90
3
Marking
2.00 ±0.05 1.10
4
Bottom View
2
0.80 max
1
0.5
1.50
1.0
0.75
1.1
Suggested Land Pattern
Option C: 3.20 x 2.50 x 0.80 Package
3.20 ±0.05
2.1
2.20
3
Marking
2.50±0.05
0.90
4
Bottom View
1
2
0.80 max
0.7
1.90
1.2
0.9
1.4
Suggested Land Pattern
Option B: 5.00 x 3.20 X 0.80 Package
5.00 ±0.05
2.39
3
Marking
3.20 ±0.05 0.80
4
Bottom View
2
0.80 max
2.54
1
1.1
2.20
1.6
1.15
1.5
Marking
Line 1 = XXXXX (Lot code)
Dot to denote Pin 1 location
Package Information
Leadframe: C194
Plating: NiPdAu
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev 01/30/16_A
Page 8 of 9
MEMS Oscillator, -55°C to +125°C, LVCMOS/HCMOS Compatible, 119.342001 MHz to 137.000MHz
IM831 Series
Tape and Reel Dimensions
PITCH
Q1 Q2
REEL DIA
TAPE
WIDTH
Q3 Q4
DIRECTION OF FEED
REF: EIA-481-E
Part
Number
Size
Pitch
Tape
Width
Pin
Orient.
IM831B
5.0 x 3.2
8.0 ± 0.1
12.3 max
Q1
IM831C
IM831D
IM831E
3.2 x 2.5
2.5 x 2.0
2.0 x 1.6
4.0 ± 0.1
4.0 ± 0.1
4.0 ± 0.1
8.3 max
8.3 max
8.3 max
Q1
Q1
Q1
Reel
Dia.
180 Dia
330 Dia
180 Dia
180 Dia
180 Dia
Count
1000
3000
3000
3000
3000
Notes:`

All dimensions are in mm.

Do not scale drawings.
PROPRIETARY AND CONFIDENTIAL
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION, AND SUCH INFORMATION MAY NOT BE DISCLOSED TO OTHERS FOR ANY
PURPOSE NOR USED FOR MANUFACTURING PURPOSES WITHOUT WRITTEN PERMISSION FROM ILSI America.
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev 01/30/16_A
Page 9 of 9