LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only ROUND TYPE LED LAMPS LDGL63033/L28-LTS DATA SHEET DOC. NO : QW0905-LDGL63033/L28-LTS REV. : A DATE : 23 - Feb. - 2006 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LDGL63033/L28-LTS Page 1/4 Package Dimensions 5.1 5.8 4.92 7.85 8.85 1.5 MAX 25MIN □0.5 TYP 1.0MIN 2.54TYP. + - Note : 1.All dimension are in millimeter tolerance is ±0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LDGL63033/L28-LTS Page 2/4 Absolute Maximum Ratings at Ta=25 ℃ Ratings Parameter Symbol UNIT DGL Forward Current IF 30 mA Peak Forward Current Duty 1/10@10KHz IFP 100 mA Power Dissipation PD 120 mW Ir 50 μA Electrostatic Discharge( * ) ESD 150 V Operating Temperature Topr -20 ~ +80 ℃ Storage Temperature Tstg -30 ~ +100 ℃ Soldering Temperature Tsol Reverse Current @5V Max 260 ℃ for 5 sec Max (2mm from body) Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic * glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Typical Electrical & Optical Characteristics (Ta=25 ℃) PART NO MATERIAL COLOR Emitted Forward Dominant Spectral voltage wave halfwidth @20mA(V) length △λ nm λDnm @20mA(mcd) Viewing angle 2θ 1/2 (deg) Typ. Max. Min. Typ. Lens LDGL63033/L28-LTS InGaN/GaN Green Water Clear Luminous intensity 505 32 3.5 Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. 4.0 6200 11500 20 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LDGL63033/L28-LTS Page 3/4 Typical Electro-Optical Characteristics Curve DGL CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 3.0 Relative Intensity Normalize @20mA Forward Current(mA) 1000 100 10 1.0 2.5 2.0 1.5 1.0 0.5 0.0 0.1 2.0 1.0 3.0 4.0 5.0 1.0 10 Fig.3 Forward Voltage vs. Temperature Fig.4 Relative Intensity vs. Temperature 1.2 3.0 Relative Intensity@20mA Normalize @25℃ Forward Voltage@20mA Normalize @25℃ 1000 Forward Current(mA) Forward Voltage(V) 1.1 1.0 0.9 0.8 -40 -20 0 20 40 60 80 100 Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0.0 450 500 550 Wavelength (nm) 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 Ambient Temperature( ℃) Ambient Temperature( ℃) Relative Intensity@20mA 100 600 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 4/4 PART NO. LDGL63033/L28-LTS Reliability Test: Test Item Test Condition Description Reference Standard Operating Life Test 1.Under Room Temperature 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) This test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. High Temperature High Humidity Test 1.Ta=65 ℃±5℃ 2.RH=90 %~95 % 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hours. Thermal Shock Test 1.Ta=105 ℃±5 ℃&-40 ℃±5℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5℃ 2.Dwell time= 10 ±1sec. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=230 ℃±5℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2 JIS C 7021: B-12 MIL-STD-202:103B JIS C 7021: B-11