A-A-59235

[INCH-POUND]
A-A-59235
3 June 2003
COMMERCIAL ITEM DESCRIPTION
COIL, RF, CHIP, FIXED, POWER, MAGNETICALLY SHIELDED,
SURFACE MOUNT
The General Services Administration has authorized the use of this
commercial item description (CID) for all federal agencies.
1. SCOPE. This CID covers the general requirements for a radio frequency coil. Coils covered by this
CID are intended for commercial/industrial applications.
2. CLASSIFICATION. This CID uses a classification system which is included in the Part Identification
Number (PIN) as shown in the following example (see 7.1).
AA59235
-
CID
number
001
Dash number
(see table I)
3. SALIENT CHARACTERISTICS.
3.1 Interface and physical dimensions. Coils supplied to this CID shall be as specified herein. (see figure
1).
3.2. Electrical characteristics. The electrical characteristics shall be as specified in table I.
3.3 Weight. The weight shall be no greater than 0.5 gram maximum.
3.4 Operating temperature range. The operating temperature range is –40°C to +85°C.
3.5 Temperature rise. DC current rating for a 15°C rise.
3.6 Altitude. The maximum altitude is 70,000 feet.
3.7 Marking. Inductors supplied to this CID shall be marked with the manufacturer’s standard
commercial PIN.
Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may
improve this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT,
Post Office Box 3990, Columbus, OH 43216-5000, or telephone (614) 692-0557, or facsimile (FAX)
(614) 692-6939.
AMSC N/A
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
FSC 5950
A-A-59235
Dimension
Inches
A
.175 Max
B
mm
Dimension
Inches
mm
4.45 Max
G
.040
1.02
.260 Max
6.60 Max
H
.120
3.05
C
.160 Dia
4.06 Dia
I
.055
1.40
D
.115 Max
2.92 Max
J
.160
4.06
E
.050
1.27
K
.270
6.86
F
.170
4.32
L
.140
3.56
NOTES:
1. Dimensions are in Inches.
2. Metric equivalents (in parenthesis) are listed for general information only.
FIGURE 1. Configuration and dimensions.
2
A-A-59235
TABLE I. Electrical characteristics.
L ±20%
DCR Max
SRF typ
(µH)
(Ohms)
(MHz)
001
1.0
.065
130
002
1.5
.070
120
003
2.2
.075
100
004
3.3
.080
70
005
4.7
.085
60
CID dash
number
AA59235-
006
.090
50
007
10
6.8
.125
45
008
15
.135
35
009
22
.160
25
010
33
.275
20
011
47
.300
17
012
68
.575
14
013
100
1.10
12
014
150
1.40
7
015
220
2.25
7
016
330
2.90
6
017
470
3.60
4
018
680
4.55
3.5
019
1000
8.10
2.5
4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials
to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition
Regulation (FAR).
5. PRODUCT CONFORMANCE PROVISIONS
5.1 Product conformance. The products provided shall meet the salient characteristics of this CID,
conform to the producer’s own drawings, specifications, standards, and quality assurance practices, and
be the same product offered for sale in the commercial market. The Government reserves the right to
require proof of such conformance.
5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality
of the product to be provided under this CID:
a. The company producing the item must have been producing a product meeting the requirements
of this CID for at least 2 years.
b. The company must have sold 1,000 units meeting this CID in the commercial marketplace over
the past 2 years.
3
A-A-59235
6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order.
7. NOTES.
7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID.
See section 2 for PIN format example.
7.2 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and
submission of these inductors to DSCC under the Military Parts Control Advisory Group (MPCAG)
evaluation program, CAGE code 58536 should be used.
7.3 Ordering data. The contract or order should specify the following:
a. CID document number, revision, and CID PIN.
b. Product conformance provisions.
c. Packaging requirements.
7.4 Commercial products. As part of the market analysis and research effort, this CID was coordinated
with the following manufacturers of commercial products. At the time of CID preparation and
coordination, these manufacturers were known to have commercial products that would meet the
requirements of this CID. (NOTE: This information should not be considered as a list of approved
manufacturers or be used to restrict procurement to only the manufacturers shown.)
MFR's CAGE
02113
MFR's name and address
Coilcraft Inc
1102 Silver Lake Road
Cary, Illinois 60013-1658
Phone number (847) 639-2361
Uniform Resource Locator (URL): www.coilcraft.com
4
A-A-59235
7.5 Part number (P/N) supersession data. This CID supersedes the following manufacturers' P/N's as
shown. This information is being provided to assist in reducing proliferation in the government inventory
system.
TABLE II. P/N supersession data.
CID dash
number
(see table I)
AA59235-
Vendor commercial
PIN
CAGE 02113
1/
001
DT1608C-102
002
DT1608C-152
003
DT1608C-222
004
DT1608C-332
005
DT1608C-472
006
DT1608C-682
007
DT1608C-103
008
DT1608C-153
009
DT1608C-223
010
DT1608C-333
011
DT1608C-473
012
DT1608C-683
013
DT1608C-104
014
DT1608C-154
015
DT1608C-224
016
DT1608C-334
017
DT1608C-474
018
DT1608C-684
019
DT1608C-105
1/ The manufacturer's P/N shall not be used for procurement to the requirements of this CID.
At the time of preparation of this CID, the aforementioned commercial products were
reviewed and could be replaced by the CID P/N shown.
7.6 Government users. To acquire information on obtaining these inductors from the Government
inventory system, contact Defense Supply Center, Columbus, ATTN: DSCC-CPAA, Post Office Box
3990, Columbus, OH 43216-5000, or telephone (614) 692-7741.
MILITARY INTERESTS:
CIVIL AGENCY COORDINATING ACTIVITY:
GSA - 7FXE
Custodians:
Navy - EC
Preparing Activity:
DLA - CC
Project 5950-1156
5
Similar pages