Model No. Rev. FYS-12011BUHR-21 A PRODUCT SPECIFICATION Model No. ：FYS-12011BUHR-21 Descriptions: ■1.20 Inch Single Digit Display ■Common Anode ■Emitting Color：Ultra Hi Red ■Chip Material:AlGaInP ■Gray Face ■White Diffused Segment CUSTOMER APPROVED SIGNATURES APPROVED BY CHECKED BY NINGBO FORYARD OPTOELECTRONICS CO.,LTD Add:NO.115 Qixin Road Ningbo Zhejiang China Tel: 0086-574-87933652 87927870 87922206 Fax: 0086-574-87927917 E-mail:[email protected] ( General) Http://www.foryard.com Http://www.foryard.com PREPARED BY Zip:315051 Page ： 1/7 Model No. Rev. FYS-12011BUHR-21 A ：FYS-12011BUHR-21 Model No. ■ Features 1. 2. 3. 4. 5. 6. 1.20 inch (30.60mm) digit height. Case mold type. RoHS compliant. Low current operation Low power consumption. Easy mounting on P.C. board or socket. ■ Mechanical Dimensions - Notes: 1. All pins are Φ0.50[.020]mm 2. Dimension in millimeter [inch], tolerance is ±0.25 [.010] and angle is ±1° unless otherwise noted. 3. Bending ≤Length*1%. 4.The specifications,characteristics and technical data described in the datasheet are subject to change without prior notice. Http://www.foryard.com Page ： 2/7 Model No. Rev. FYS-12011BUHR-21 A ：FYS-12011BUHR-21 Model No. ■ All Light On Segments Feature & Pin Position ■ Internal Circuit Diagrams - Http://www.foryard.com Page ： 3/7 FYS-12011BUHR-21 A Model No. Rev. ：FYS-12011BUHR-21 Model No. ■ Absolute maximum ratings (Ta=25 Parameter Reverse Voltage Forward Current Power Dissipation Pulse Current Operating Temperature Storage Temperature Symbol Test Condition VR IF Pd Ipeak Topr Tstr IR=30 — — Duty=0.1mS,1KHz — — Value Min Max 5 — — — -40 -40 — 30 100 150 +85 +85 ■ Electrical-Optical Characteristics ● Color Code & Chip Characteristics:(Test Condition:IF=20mA) Emitting Color UHR Peak Wave Dice Material Length(λP) Spectral Line halfwidt h(∆λ1/2) Unit V mA mW mA ℃ ℃ (Ta=25 Forward Voltage(VF) Unit:V Typ Max AlGaInP 640nm Ultra Hi Red 20nm 1.90 Segment-to-Segment Luminous Intensity ratio(Iv-M) 2.50 1.5:1 ℃) ℃) Luminous Intensity (Iv) Unit:mcd 30~60 Note: 1.Luminous Intensity is based on the Foryard standards. 2.Pay attention about static for InGaN Http://www.foryard.com Page ： 4/7 FYS-12011BUHR-21 A Model No. Rev. ：FYS-12011BUHR-21 Model No. ■ Typical Electrical / Optical Characteristics Curves (Ta = 25 ℃ Unless Otherwise Noted) (A) 1.0 (B) (C) (D) (E) (7) (8) (6) (5)(4) (3) (2) (1) (9) (10) 0.5 0 350 400 450 500 550 600 650 700 750 800 Wavelength(nm) RELATIVE INTENSITY Vs WAVELENGTH( 78 6 45 1 (4)-AlGaInP/640nm/Ultra Hi Red (B)-InGaN/SiC 460nm/Blue (C)-InGaN/SiC 470nm/Blue (D)-InGaN/SiC 505nm/Ultra Green 2 3 20 10 0 1.6 2.0 2.4 2.6 3.0 50 1 3.0 2.0 5 B 1.0 0 20 FORWARD VOLTAGE(Vf) 40 60 80 3KHZ 1 5 4 2 3 0.2 -10 0 10 10 0 100 20 1KHZ 10KHZ 20 30 40 50 60 60 3KHZ 300KHZ F-REFRESH RATE 100KHZ 80 100 1KHZ 10KHZ 300KHZ 100KHZ 10 9 8 7 6 6 5 5 4 3 4 3 2 70 1 1 1 AMBIENT TEMPERATURE Ta(°C) 40 AMBIENT TEMPERATURE Ta( ) FORWARD CURRENT VS. AMBIENT TEMPERATURE 2 -20 20 3 5 Ipeak MAX. IDC MAX. Ipeak MAX. IDC MAX. RELATIVE LUMINOUS INTENSITY 10 9 8 7 0.5 0.1 -30 6 A 30 2,4, 7, 8, INTENSITY VS FORWARD CURRENT FORWARD VOLTAGE 1 40 1 FORWARD CURRENT (mA) RELATIVE LUMINOUS FORWARD CURRENT VS. 3 2 FORWARD CURRENT(mA) RELATIVE LUMINOUS INTENSITY FORWARD CURRENT(mA) 30 1000 (E)-InGaN/SiC 525nm/Ultra Green 2,3,4, 6, 7, 8 4.0 950 λp) (9)-GaAlAs 880mm (10)-GaAs/GaAs & GaAlAs/GaAs 940nm (A)-GaN/SiC 430nm/Blue 40 1.2 900 (1)-GaP 700nm/Red (2)-AlGaAs/SH 660nm/Hi Red (3)-AlGaAs/DH 650nm/Super Red (5)-AlGaInP/635nm/Ultra Red (6)-GaAlP/AlGaInP/625nm/Orange (7)-GaAsP/AlGaInP 610nm/Amber (8)-GaP 570nm/Yellow Green 50 850 10 100 1000 tp-PULSE DURATION uS (1,2,3,4,6,8,B,D,J,K) 10.000 1 10 100 1000 10.000 tp-PULSE DURATION uS (5) NOTE:25°C free air temperature unless otherwise specified Http://www.foryard.com Page ： 5/7 Model No. Rev. FYS-12011BUHR-21 A ：FYS-12011BUHR-21 Model No. ■ Precautions For Use - 1. Recommended Soldering conditions-Wave Soldering 260(max.) Temperature(° C) 250 240 Preheat 105(max.) 0 5 sec. Max. 60sec. 2. Soldering Iron Basic SPEC. is ≦5sec. When 260℃. If temperature is higher, time should be shorter (+10℃→ -1sec.). Power dissipation of iron should be smaller than 15W,and temperature should be controllable. Surface temperature of the device should be under 230 Http://www.foryard.com ℃. Page ： 6/7 FYS-12011BUHR-21 A Model No. Rev. ：FYS-12011BUHR-21 Model No. ■ Packing Diagram 30PCS/Foam FORYARD RoHS Part NO: FYS-12011BUHR-21 Q'TY: 120 PCS Date:xxxx/xx/xx PASS QC: QC xxxxxxxxxx 4Foams/Bag 56.0 OUTSIDE LABEL .0 31 0. 63 54.0 0. 71 FORYARD 4Bags/Box www.foryard.com .5 14 4Boxes/Carton FORYARD LED PN:FYS-12011BUHR-21 Qty: 1920 PCS Date:xxxx/xx/xx GW: 22.22KG PASS QC: QC NW: 19.66KG xxxxxxxxxx RoHS ATTENTION OUTSIDE LABEL Note: The specifications are subject to change without notice. Please contact us for updated information. Http://www.foryard.com Page ： 7/7