LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PHOTO DIODE SILICON PIN LED LAMPS Pb Lead-Free Parts LPD9033 DATA SHEET DOC. NO : QW0905-LPD9033 REV. : A DATE : 24 - Nov. - 2014 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LPD9033 Page1/4 Package Dimension Description The LPD9033 series are silicon planar P/N photodiodes incorporated in plastic package that simultaneously serve as filter and are also Transparent for infrared emission their terminals are soldering tabs arranged in 2.54mm center to center spacing due to their design the diodes can vertically be assembled on pc boards arrays can be realized by multiple arrangement versatile photodetectors are suitable for diodes as well as voltaic cell operation the signal noise ratio is particularly favorable even at low illuminance the P/N photodiode are outstanding for low junction capacitance high cut-off frequency and fast switching times. They are particularly suitable for IR sound transmission and remote control the cathode of LPD9033 photodiode is marked by a stamping on the package edge Cathode Mark 7.0MIN 7.0MIN 2.0 0.4±0.1 2.5 1.4 1.4 ψ1.9 0.5±0.1 1 0.16 0.7 2 0.7 2.5 1.ANODE 2.CATHODE NOTE:1.All dimension are In millimeters tolerance Is ±0.25 unless otherwise noted 2.Specifications are subject to change without notice •MAXIMUM RATINGS (TA=25℃) Symbol Rating Reverse Break Down Voltage VBR 30 V Power Dissipation PD 150 mW Operating Temperature Topr -30 ﹣ +60 ℃ Storage Temperature Tstg -40 ﹣ +60 ℃ Characteristic nit • ELECTRICAL CHARACTERISTICS AT (TA=25℃) Characteristic Symbol Test Condition Typ Max Unit － 1.0 30 nA 1.0 2.0 － uA Dark Current ID Short Circuit Current Isc Open Circuit Voltage Voc λP=940nm Ee=0.5mW/c㎡ _ 350 － mV Total Capacitance CT VR=3V f=1MHZ Ee=0mW/c㎡ － 20 － pF － 940 － nm － 50 － ns Peak Wavelength of Max Sensitivity Rise Time,Fall Time VR=10V Ee=0mW/c㎡ Min VR=5V λP=940nm Ee=0.5mW/c㎡ λsmax tr,tf VR=10V R L=1KΩ LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LPD9033 Page 2/4 Recommended Soldering Conditions 1. Hand Solder Basic spec is ≦ 280℃ 3 sec one time only. 2. Wave Solder Soldering heat Max. 260 ℃ 245± 5℃ within 5 sec Preheat 120 ~ 150 ℃ 120 ~ 180 sec 3-1. LEAD Reflow Solder Temp. (℃) 240 Rising +5 ℃/sec Cooling -5℃/sec Preheat 150 120 60 ~ 120 sec Time 5sec 3-2 PB-Free Reflow Solder 1~5°C/sec Preheat 180~200 °C 1~5° C/sec 260° C MaX. 10sec.Max Above 220 °C 60 sec.Max. 120 sec.Max. Note: 1.Wave solder and reflow soldering should not be made more than one time. 2.You can just only select one of the soldering conditions as above. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LPD9033 Page 3/4 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH<60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH<60%, they should be treated at 60 ℃± 5 ℃fo r 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LPD9033 Page 4/4 Reliability Test: Classification Test Item Test Condition Reference Standard Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) MIL-STD-883D:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) JIS C 7021: B-12 High Temperature High Humidity Storage Test 1.Ta=65 ℃±5 ℃ 2.RH=90 %~95% 3.t=1000hrs ±2hrs Endurance Test Thermal Shock Test Solderability Test Environmental Test Temperature Cycling IR Reflow 1.Ta=105 ℃±5℃&-40 ℃±5℃ (10min) (10min) 2.total 10 cycles 1.T.Sol=235 ℃±5℃ 2.Immersion time 2 ±0.5sec 3.Coverage ≧95% of the dipped surface 1.105 ℃ ~ 25℃ ~ - 55℃ ~ 25 ℃ 30mins 5mins 30mins 5mins 2.10 Cyeles 1.T=260 °C Max. 10sec.Max. 2. 6 Min MIL-STD-202F:103B JIS C 7021: B-11 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011 MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4 MIL-STD-750D:2031.2 J-STD-020