QUINTOLUBRIC® 888-46 FIRE RESISTANT HFD-U HYDRAULIC FLUID APPLICATION SHEET BENEFITS »»Global formulation »»Best-in-class oxidation stability »»Excellent shear stability »»Environmentally friendly APPLICATIONS PROPERTIES QUINTOLUBRIC® 888-46 was designed to replace anti-wear, mineral oil-based hydraulic fluids used in applications where fire hazards exist. QUINTOLUBRIC® 888-46 can also be used in environmentally sensitive hydraulic applications without compromising the overall hydraulic system operations. This fluid does not contain water, mineral oil, or phosphate ester, and is based on high-quality, synthetic, organic esters and carefully selected additives to achieve excellent hydraulic fluid performance. QUINTOLUBRIC® 88846 offers the lubrication level of premium, antiwear hydraulic oils, and can be used with hydraulic components from all major manufacturers. COMPATIBILITY The chart on the back contains our recommendations regarding the use of QUINTOLUBRIC® 888-46 with commonly used elastomers. The elastomer applications listed are “Static,” which refers to trapped nonmoving seals such as O-rings in valve sub-plates and rigid, low pressure hose connections; “MildDynamic,” whose applications include accumulator bladders and hose linings where the hoses are exposed to high pressure and light flexing; and “Dynamic,” which refers to cylinder rod seals, pump shaft seals and constantly flexing hydraulic hose. PROPERTIES (TEST METHOD) TYPICAL VALUES Appearance Kinematic Viscosity (ASTM D 445) At 0OC At 20OC At 40OC At 100OC Viscosity Index (ASTM D 2270) Density at 15OC (ASTM D 1298) Acid Number (ASTM D 974) Pour Point (ASTM D 97) Foam Test at 25oC (ASTM D 892) Sequence I Corrosion Protection ISO 4404-2 ASTM D665A/D130 Dry TOST (ASTM D943 mod.) Flash Point (ASTM D 92) Fire Point (ASTM D 92) Air Release (ASTM D 3427) Pump Test (ASTM D 2882) Gear Lubrication (DIN 51354-2) Water Separability (ASTM D 1401) Yellow to amber fluid quakerchem.com | quintolubric.com | [email protected] 320 mm2/s or cSt 109 mm2/s or cSt 47.5 mm2/s or cSt 9.5 mm2/s or cSt 190 0.92 g/cm3 2.0 mg KOH/g < -30OC (< -22OF) 50-0 ml-ml Pass Pass/1a 800 hrs 300OC (572OF) 360OC (680OF) 7 min <5 mg wear >12 FZG load stage 41-39-0 (30) ml-ml-ml (min.) QUINTOLUBRIC® 888-46 FIRE RESISTANT HFD-U HYDRAULIC FLUID APPLICATION SHEET METALS QUINTOLUBRIC® 888-46 is compatible with iron and steel alloys and most nonferrous metals and their alloys. It is not compatible with lead, cadmium and has limited compatibility with alloys containing high levels of these metals. QUINTOLUBRIC® 888-46 has limited compatibility with hot dipped or electro galvanized surfaces and good compatibility with zinc containing alloys. Suitable substitutes for these materials are available and should be used. ELASTOMERS ISO 1629 DESCRIPTION NBR ENGINEERING DATA PROPERTIES (TEST METHOD) S* MD* D* C C C Fluoroelastomer (Viton®) Neoprene C S C S C S Butyl rubber Ethylene propylene rubber Polyurethane Teflon® S N C C N N C C N N C C Medium to high nitrile rubber (Buna N,>30% acrylonitrile) FPM CR IIR EPDM PU PTFE **(S- Static, MD- Mild Dynamic, D- Dynamic) C = Compatible S = Satisfactory for short term use, but replacement with a completely compatible elastomer is recommended at the earliest convenience. N = Not Compatible Specific Heat at 20OC (D2766) Coefficient of Thermal Expansion at 20OC (D1903) Vapor Pressure (02551) At 20OC At 66OC Bulk Modulus at 20OC At 210 bar At 3,000 psi Thermal Conductivity at 19OC (D 2717) Dielectric Breakdown Voltage (D877) TYPICAL VALUES 2.06 kJ/kg OC .49 Btu/lb OF 6 X 10-4 per OC 3.2 X 10-6 mmHg 7.5 X10-6 mm Hg 1.87 X 105 N/cm2 266,900 psi 0.167 J/sec/m/OC 30 kV *country specific SDS are available PAINTS AND COATINGS IGNITION TEST DATA QUINTOLUBRIC® 888-46 is compatible with multicomponent epoxy coatings. It is not compatible with zinc-based coatings. Specific coating and application recommendations can be obtained from coating manufacturers or directly from Quaker. Hot Manifold Ignition Temperature (ISO 20823) Auto Ignition Temperature (DIN 51794) >450oC >400oC (>750oF) BIODEGRADABILITY TEST DATA OECD-301 c 86.5% biodegradable after 28 days FLUIDS QUINTOLUBRIC® 888-46 is compatible and miscible with nearly all mineral oil and polyolester-type hydraulic fluids and with some, but not all, phosphate esters. It is not miscible or compatible with water-containing fluids. For conversion recommendations, please contact Quaker. quakerchem.com | quintolubric.com | [email protected] Prior to using this product, consult the Material Safety Data Sheet for instructions regarding safe handling and environmental issues. The information contained herein is based on data available to us and is believed to be accurate. HOWEVER, NO WARRANTY OF MERCHANTABILITY, FITNESS FOR ANY USE, OR ANY OTHER WARRANTY IS EXPRESSED OR TO BE IMPLIED, REGARDING THE ACCURACY OF THESE DATA. THE RESULTS TO BE OBTAINED FROM THE USE THEREOF, OR THE HAZARDS CONNECTED WITH THE USE OF THE PRODUCT. Quaker Chemical Corporation assumes no liability for any alleged ineffectiveness of the product or any injury or damage, direct or consequential, resulting from the use of this product unless such injury or damage is solely attributable to negligence on the part of Quaker Chemical Corporation. 014113 04/2013