X40626 ® 64K, 8K x 8 Bit Data Sheet PRELIMINARY March 28, 2005 Dual Voltage CPU Supervisor with 64K Serial EEPROM FN8119.0 • 2.7V to 5.5V power supply operation • Available Packages —14-lead SOIC —14-lead TSSOP FEATURES • Dual voltage monitoring —V2Mon operates independent of VCC • Watchdog timer with selectable timeout intervals • Low VCC detection and reset assertion —Four standard reset threshold voltages —User programmable VTRIP threshold —Reset signal valid to VCC=1V • Low power CMOS —20µA max standby current, watchdog on —1µA standby current, watchdog OFF • 64Kbits of EEPROM —64 byte page size • Built-in inadvertent write protection —Power-up/power-down protection circuitry —Protect 0, 1/4, 1/2, all or 64, 128, 256 or 512 bytes of EEPROM array with programmable Block Lock™ protection • 400kHz 2-wire interface —Slave addressing supports up to 4 devices on the same bus DESCRIPTION The X40626 combines four popular functions, Power-on Reset Control, Watchdog Timer, Dual Supply Voltage Supervision, and Serial EEPROM Memory in one package. This combination lowers system cost, reduces board space requirements, and increases reliability. Applying power to the device activates the power-on reset circuit which holds RESET active for a period of time. This allows the power supply and oscillator to stabilize before the processor can execute code. The Watchdog Timer provides an independent protection mechanism for microcontrollers. When the microcontroller fails to restart a timer within a selectable timeout interval, the device activates the RESET signal. The user selects the interval from three preset values. Once selected, the interval does not change, even after cycling the power. BLOCK DIAGRAM V2 Monitor Logic Watchdog Transition Detector WP V2FAIL + VTRIP2 - V2MON Watchdog Timer Reset Protect Logic RESET Data Register Command Decode & Control Logic SCL S0 S1 VCC Threshold Reset logic Status Register Block Lock Control SDA 64KB EEPROM Array VCC + VTRIP 1 - Reset & Watchdog Timebase Power-on and Low Voltage Reset Generation CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-352-6832 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005. All Rights Reserved All other trademarks mentioned are the property of their respective owners. X40626 The device’s low VCC detection circuitry protects the user’s system from low voltage conditions, resetting the system when VCC falls below the set minimum VCC trip point. RESET is asserted until VCC returns to proper operating level and stabilizes. Four industry standard Vtrip thresholds are available. However, Intersil’s unique circuits allow the threshold to be reprogrammed to meet custom requirements or to fine-tune the threshold for applications requiring higher precision. The memory portion of the device is a CMOS Serial EEPROM array with Intersil’s Block Lock™ Protection. The array is internally organized as 64 bytes per page. The device features an 2-wire interface and software protocol allowing operation on an I2C bus. The device utilizes Intersil’s proprietary Direct Write™ cell, providing a minimum endurance of 100,000 page write cycles and a minimum data retention of 100 years. PIN CONFIGURATION 14 Pin SOIC/TSSOP NC S0 S1 NC RESET NC VSS 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VCC NC WP V2MON V2FAIL SCL SDA PIN FUNCTION Pin Name Function 1, 4, 6, 13 NC No Internal Connections 2 S0 Device Select Input 3 S1 Device Select Input 5 RESET 7 VSS Ground 8 SDA Serial Data. SDA is a bidirectional pin used to transfer data into and out of the device. It has an open drain output and may be wire ORed with other open drain or open collector outputs. This pin requires a pull up resistor and the input buffer is always active (not gated). Watchdog Input. A HIGH to LOW transition on the SDA (while SCL is HIGH) restarts the Watchdog timer. The absence of a HIGH to LOW transition within the watchdog time-out period results in RESET going active. 9 SCL Serial Clock. The Serial Clock controls the serial bus timing for data input and output. 10 V2FAIL V2 Voltage Fail Output. This open drain output goes LOW when V2MON is less than VTRIP2 and goes HIGH when V2MON exceeds VTRIP2. There is no power-up reset delay circuitry on this pin. This circuit works independently from the Low VCC reset and battery switch circuits. Connect V2FAIL to VSS when not used. 11 V2MON V2 Voltage Monitor Input. When the V2MON input is less than the VTRIP2 voltage, V2FAIL goes LOW. This input can monitor an unregulated power supply with an external resistor divider or can monitor a second power supply with no external components. Connect V2MON to VSS or VCC when not used. There is no hysteresis in the V2MON comparator circuits. 12 WP Write Protect. WP HIGH used in conjunction with WPEN bit prevents writes to the control register. 14 VCC Supply Voltage Reset Output. RESET is an active LOW, open drain output which goes active whenever VCC falls below the minimum VCC sense level. It will remain active until VCC rises above the minimum VCC sense level for typically 200ms. RESET goes active if the Watchdog Timer is enabled and SDA remains either HIGH or LOW longer than the selectable Watchdog time-out period. A falling edge on SDA, while SCL is HIGH, resets the Watchdog Timer. RESET goes active on power-up and remains active for typically 200ms after the power supply stabilizes. 2 FN8119.0 March 28, 2005 X40626 EEPROM INADVERTENT WRITE PROTECTION PRINCIPLES OF OPERATION Power-on Reset Application of power to the X40626 activates a poweron Reset Circuit that pulls the RESET pin active. This signal provides several benefits. – It prevents the system microprocessor from starting to operate with insufficient voltage. – It prevents the processor from operating prior to stabilization of the oscillator. – It allows time for an FPGA to download its configuration prior to initialization of the circuit. – It prevents communication to the EEPROM, greatly reducing the likelihood of data corruption on power-up. When VCC exceeds the device VTRIP threshold value for tPURST (200ms nominal) the circuit releases RESET allowing the system to begin operation. LOW VOLTAGE MONITORING During operation, the X40626 monitors the VCC level and asserts RESET if supply voltage falls below a preset minimum VTRIP. The RESET signal prevents the microprocessor from operating in a power fail or brownout condition. The RESET signal remains active until the voltage drops below 1V. It also remains active until VCC returns and exceeds VTRIP for 200ms. WATCHDOG TIMER The Watchdog Timer circuit monitors the microprocessor activity by monitoring the SDA and SCL pins. The microprocessor must toggle the SDA pin HIGH to LOW periodically, while SCL is HIGH (this is a start bit) prior to the expiration of the watchdog time-out period to prevent a RESET signal. The state of two nonvolatile control bits in the Status Register determine the watchdog timer period. The microprocessor can change these watchdog bits, or they may be “locked” by tying the WP pin HIGH. When RESET goes active as a result of a low voltage condition or Watchdog Timer Time-Out, any inprogress communications are terminated. While RESET is active, no new communications are allowed and no non-volatile write operation can start. Non-volatile writes in-progress when RESET goes active are allowed to finish. Additional protection mechanisms are provided with memory Block Lock and the Write Protect (WP) pin. These are discussed elsewhere in this document. VCC/V2MON THRESHOLD RESET PROCEDURE The X40626 is shipped with a standard VCC threshold (VTRIP) voltage. This value will not change over normal operating and storage conditions. However, in applications where the standard VTRIP is not exactly right, or if higher precision is needed in the VTRIP value, the X40626 threshold may be adjusted. The procedure is described below, and uses the application of a nonvolatile control signal. Setting the VTRIP Voltage This procedure is used to set the VTRIP to a higher or lower voltage value. It is necessary to reset the trip point before setting the new value. The VCC and V2MON must be tied together during this sequence. To set the new VTRIP voltage, start by setting the WEL bit in the control register, then apply the desired VTRIP threshold voltage to the VCC pin and the programming voltage, VP , to the WP pin and 2 byte address and 1 byte of “00” data. The stop bit following a valid write operation initiates the VTRIP programming sequence. Bring WP LOW to complete the operation. Figure 1. Set VTRIP Level Sequence (VCC/V2MON = desired VTRIP values, WP = 12-15V when WEL bit set) VP = 12-15V WP 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 xxH* 00H SCL SDA A0H 00H *for VVTRIP2 address is 0DH for VTRIP address is 01H 3 FN8119.0 March 28, 2005 X40626 To reset the new VTRIP voltage start by setting the WEL bit in the control register, apply the desired VTRIP threshold voltage to the VCC pin and the programming voltage, VP , to the WP pin and 2 byte address and 1 byte of “00” data. The stop bit of a valid write operation initiates the VTRIP programming sequence. Bring WP LOW to complete the operation. Resetting the VTRIP Voltage This procedure is used to set the VTRIP to a “native” voltage level. For example, if the current VTRIP is 4.4V and the new VTRIP must be 4.0V, then the VTRIP must be reset. When VTRIP is reset, the new VTRIP is something less than 1.7V. This procedure must be used to set the voltage to a lower value. Figure 2. Reset VTRIP Level Sequence (VCC/V2MON > 3V, WP = 12-15V, WEL bit set) VP = 12-15V WP 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCL SDA A0H xxH* 00H 00H *for VTRIP2 address is 0FH for VTRIP address is 03H Figure 3. Sample VTRIP Reset Circuit VP 1 4.7K RESET VTRIP Adj. 4 14 13 2 12 3 4 X40626 5 6 9 7 8 Adjust µC Run SCL SDA FN8119.0 March 28, 2005 X40626 Figure 4. VTRIP Programming Sequence VTRIPX Programming Vx = VCC, V2MON Let: MDE = Maximum Desired Error No Desired VTRIPX Present Value MDE+ Acceptable Desired Value YES Error Range MDE– Set VX = Desired VTRIPX Error = Actual - Desired Execute Set Higher VTRIPX Sequence New VX applied = Old VX applied + | Error | Execute Set Higher VX Sequence New VX applied = Old VX applied - | Error | Apply VCC and Voltage > Desired VTRIPX to VX Execute Reset VTRIPX Sequence NO Decrease VX Output Switches? YES Error < MDE– Actual VTRIPX Desired VTRIPX Error > MDE+ | Error | < | MDE | DONE 5 FN8119.0 March 28, 2005 X40626 Control Register BP2, BP1, BP0: Block Protect Bits - (Nonvolatile) The Control Register provides the user a mechanism for changing the Block Lock and Watchdog Timer settings. The Block Lock and Watchdog Timer bits are nonvolatile and do not change when power is removed. The Block Protect Bits, BP2, BP1 and BP0, determine which blocks of the array are write protected. A write to a protected block of memory is ignored. The block protect bits will prevent write operations to one of eight segments of the array. 0 000h - 03FH (64 bytes) First Page (P1) 0 1 000h - 07FH (128 bytes) First 2 pgs (P2) 1 1 0 000h - 0FFH (256 bytes) First 4 pgs (P4) 1 1 1 000h - 1FFH (512 bytes) First 8 Pgs (P8) The state of the Control Register can be read at any time by performing a random read at address FFFFh. Only one byte is read by each register read operation. The X40626 resets itself after the first byte is read. The master should supply a stop condition to be consistent with the bus protocol, but a stop is not required to end this operation. 7 6 5 4 3 2 1 0 WPEN WD1 WD0 BP1 BP0 RWEL WEL BP2 BP0 0 1 BP1 1 The user must issue a stop after sending this byte to the register to initiate the nonvolatile cycle that stores WD1, WD0, BP2, BP1, and BP0. The X40626 will not acknowledge any data bytes written after the first byte is entered. BP2 The Control Register is accessed at address FFFFh. It can only be modified by performing a byte write operation directly to the address of the register and only one data byte is allowed for each register write operation. Prior to writing to the Control Register, the WEL and RWEL bits must be set using a two step process, with the whole sequence requiring 3 steps. See "Writing to the Control Register" below. Protected Addresses (Size) 0 0 0 None (factory setting) 0 0 1 1800h - 1FFFH (2K bytes) 0 1 0 1000h - 1FFFH (4K bytes) Upper 1/2 (Q3,Q4) 0 1 1 0000h - 1FFFH (8K bytes) Array Lock None Upper 1/4 (Q4) Full Array (All) WD1, WD0: Watchdog Timer Bits The bits WD1 and WD0 control the period of the Watchdog Timer. The options are shown below. WD1 WD0 Typ. Watchdog Time-out Period 0 0 1.4 Seconds 0 1 600 milliseconds 1 0 200 milliseconds 1 1 Disabled (factory setting) RWEL: Register Write Enable Latch (Volatile) Write Protect Enable The RWEL bit must be set to “1” prior to a write to the Control Register. These devices have an advanced Block Lock scheme that protects one of eight blocks of the array when enabled. It provides hardware write protection through the use of a WP pin and a nonvolatile Write Protect Enable (WPEN) bit. Four of the 8 protected blocks match the original Block Lock segments and this protection scheme is fully compatible with the current devices using 2 bits of block lock control (assuming the BP2 bit is set to 0). WEL: Write Enable Latch (Volatile) The WEL bit controls the access to the memory and to the Register during a write operation. This bit is a volatile latch that powers up in the LOW (disabled) state. While the WEL bit is LOW, writes to any address, including any control registers will be ignored (no acknowledge will be issued after the Data Byte). The WEL bit is set by writing a “1” to the WEL bit and zeroes to the other bits of the control register. Once set, WEL remains set until either it is reset to 0 (by writing a “0” to the WEL bit and zeroes to the other bits of the control register) or until the part powers up again. Writes to the WEL bit do not cause a nonvolatile write cycle, so the device is ready for the next operation immediately after the stop condition. 6 The Write Protect (WP) pin and the Write Protect Enable (WPEN) bit in the Control Register control the programmable Hardware Write Protect feature. Hardware Write Protection is enabled when the WP pin and the WPEN bit are HIGH and disabled when either the WP pin or the WPEN bit is LOW. When the chip is Hardware Write Protected, nonvolatile writes as well as to the block protected sections in the memory array cannot be written. Only the sections of the memory array that are not block protected can be written. Note that since the WPEN bit is write protected, it cannot be changed back to a LOW state; so write protection is enabled as long as the WP pin is held HIGH. FN8119.0 March 28, 2005 X40626 Table 1. Write Protect Enable Bit and WP Pin Function WP WPEN Memory Array not Block Protected Memory Array Block Protected Block Protect Bits WPEN Bit Protection LOW X Writes OK Writes Blocked Writes OK Writes OK Software HIGH 0 Writes OK Writes Blocked Writes OK Writes OK Software HIGH 1 Writes OK Writes Blocked Writes Blocked Writes Blocked Hardware Writing to the Control Register Changing any of the nonvolatile bits of the control register requires the following steps: – Write a 02H to the Control Register to set the Write Enable Latch (WEL). This is a volatile operation, so there is no delay after the write. (Operation proceeded by a start and ended with a stop). – Write a 06H to the Control Register to set both the Register Write Enable Latch (RWEL) and the WEL bit. This is also a volatile cycle. The zeros in the data byte are required. (Operation proceeded by a start and ended with a stop). – Write a value to the Control Register that has all the control bits set to the desired state. This can be represented as 0xys t01r in binary, where xy are the WD bits, and rst are the BP bits. (Operation preceeded by a start and ended with a stop). Since this is a nonvolatile write cycle it will take up to 10ms to complete. The RWEL bit is reset by this cycle and the sequence must be repeated to change the nonvolatile bits again. If bit 2 is set to ‘1’ in this third step (0xys t11r) then the RWEL bit is set, but the WD1, WD0, BP2, BP1 and BP0 bits remain unchanged. Writing a second byte to the control register is not allowed. Doing so aborts the write operation and returns a NACK. – A read operation occurring between any of the previous operations will not interrupt the register write operation. 7 – The RWEL bit cannot be reset without writing to the nonvolatile control bits in the control register, power cycling the device or attempting a write to a write protected block. To illustrate, a sequence of writes to the device consisting of [02H, 06H, 02H] will reset all of the nonvolatile bits in the Control Register to 0. A sequence of [02H, 06H, 06H] will leave the nonvolatile bits unchanged and the RWEL bit remains set. SERIAL INTERFACE Serial Interface Conventions The device supports a bidirectional bus oriented protocol. The protocol defines any device that sends data onto the bus as a transmitter, and the receiving device as the receiver. The device controlling the transfer is called the master and the device being controlled is called the slave. The master always initiates data transfers, and provides the clock for both transmit and receive operations. Therefore, the devices in this family operate as slaves in all applications. Serial Clock and Data Data states on the SDA line can change only during SCL LOW. SDA state changes during SCL HIGH are reserved for indicating start and stop conditions. See Figure 5. FN8119.0 March 28, 2005 X40626 Figure 5. Valid Data Changes on the SDA Bus SCL SDA Data Stable Data Change Data Stable Serial Start Condition Serial Stop Condition All commands are preceded by the start condition, which is a HIGH to LOW transition of SDA when SCL is HIGH. The device continuously monitors the SDA and SCL lines for the start condition and will not respond to any command until this condition has been met. See Figure 6. All communications must be terminated by a stop condition, which is a LOW to HIGH transition of SDA when SCL is HIGH. The stop condition is also used to place the device into the Standby power mode after a read sequence. A stop condition can only be issued after the transmitting device has released the bus. See Figure 6. Figure 6. Valid Start and Stop Conditions SCL SDA Start Serial Acknowledge Acknowledge is a software convention used to indicate successful data transfer. The transmitting device, either master or slave, will release the bus after transmitting eight bits. During the ninth clock cycle, the receiver will pull the SDA line LOW to acknowledge that it received the eight bits of data. Refer to Figure 7. The device will respond with an acknowledge after recognition of a start condition and if the correct Device Identifier and Select bits are contained in the Slave Address Byte. If a write operation is selected, the device will respond with an acknowledge after the receipt of each subsequent eight bit word. The device will acknowledge all incoming data and address bytes, except for the Slave Address Byte when the Device Identifier and/or Select bits are incorrect. 8 Stop In the read mode, the device will transmit eight bits of data, release the SDA line, then monitor the line for an acknowledge. If an acknowledge is detected and no stop condition is generated by the master, the device will continue to transmit data. The device will terminate further data transmissions if an acknowledge is not detected. The master must then issue a stop condition to return the device to Standby mode and place the device into a known state. FN8119.0 March 28, 2005 X40626 Figure 7. Acknowledge Response From Receiver SCL from Master 1 8 9 Data Output from Data Output from Receiver Start Acknowledge Serial Write Operations Byte Write For a write operation, the device requires the Slave Address Byte and a Word Address Byte. This gives the master access to any one of the words in the array. After receipt of the Word Address Byte, the device responds with an acknowledge, and awaits the next eight bits of data. After receiving the 8 bits of the Data Byte, the device again responds with an acknowledge. The master then terminates the transfer by generating a stop condition, at which time the device begins the internal write cycle to the nonvolatile memory. During this internal write cycle, the device inputs are disabled, so the device will not respond to any requests from the master. The SDA output is at high impedance. See Figure 8. Figure 8. Byte Write Sequence S T A R T Signals from the Master Word Address Byte 1 Slave Address Word Address Byte 0 S T O P Data S 1 0 1 0 0 S1 S0 0 SDA Bus P A C K Signals from the Slave A write to a protected block of memory will suppress the acknowledge bit. Page Write The device is capable of a page write operation. It is initiated in the same manner as the byte write operation; but instead of terminating the write cycle after the first data byte is transferred, the master can transmit an unlimited number of 8-bit bytes. After the receipt of each byte, the device will respond with an acknowledge, and the address is internally incremented by one. The page address remains constant. When the 9 A C K A C K A C K counter reaches the end of the page, it “rolls over” and goes back to ‘0’ on the same page. This means that the master can write 64 bytes to the page starting at any location on that page. If the master begins writing at location 60, and loads 12 bytes, then the first 4 bytes are written to locations 60 through 63, and the last 8 bytes are written to locations 0 through 7. Afterwards, the address counter would point to location 8 of the page that was just written. If the master supplies more than 64 bytes of data, then new data over-writes the previous data, one byte at a time. FN8119.0 March 28, 2005 X40626 Figure 9. Page Write Operation (I ≤ n ≤ 63) Signals from the Master SDA Bus S T A R T Data (0) Word Address Byte 0 Word Address Byte 1 Slave Address Data (n) S T O P S 1 0 1 0 0 S1 S0 0 P A C K Signals from the Slave A C K A C K A C K A C K Figure 10. Writing 12 bytes to a 64-byte page starting at location 60 (Wrap around). 8 Bytes address =7 4 Bytes address pointer ends here Addr = 8 The master terminates the Data Byte loading by issuing a stop condition, which causes the device to begin the nonvolatile write cycle. As with the byte write operation, all inputs are disabled until completion of the internal write cycle. See Figure 9 for the address, acknowledge, and data transfer sequence. Stops and Write Modes Stop conditions that terminate write operations must be sent by the master after sending at least 1 full data byte plus the subsequent ACK signal. If a stop is issued in the middle of a data byte, or before 1 full data byte plus its associated ACK is sent, then the device will reset itself without performing the write. The contents of the array will not be effected. 10 address 60 address 63 Acknowledge Polling The disabling of the inputs during nonvolatile cycles can be used to take advantage of the typical 5mS write cycle time. Once the stop condition is issued to indicate the end of the master’s byte load operation, the device initiates the internal nonvolatile cycle. Acknowledge polling can be initiated immediately. To do this, the master issues a start condition followed by the Slave Address Byte for a write or read operation. If the device is still busy with the nonvolatile cycle then no ACK will be returned. If the device has completed the write operation, an ACK will be returned and the host can then proceed with the read or write operation. Refer to the flow chart in Figure 11. FN8119.0 March 28, 2005 X40626 Figure 11. Acknowledge Polling Sequence Serial Read Operations Read operations are initiated in the same manner as write operations with the exception that the R/W bit of the Slave Address Byte is set to one. There are three basic read operations: Current Address Reads, Random Reads, and Sequential Reads. Byte load completed by issuing STOP. Enter ACK Polling Issue START Current Address Read Issue Slave Address Byte (Read or Write) Internally the device contains an address counter that maintains the address of the last word read incremented by one. Therefore, if the last read was to address n, the next read operation would access data from address n+1. On power-up, the address in the address counter is 00H. Issue STOP NO ACK returned? Upon receipt of the Slave Address Byte with the R/W bit set to one, the device issues an acknowledge and then transmits the eight bits of the Data Byte. The master terminates the read operation when it does not respond with an acknowledge during the ninth clock and then issues a stop condition. Refer to Figure 12 for the address, acknowledge, and data transfer sequence. YES Nonvolatile Cycle complete. Continue command sequence? NO Issue STOP It should be noted that the ninth clock cycle of the read operation is not a “don’t care.” To terminate a read operation, the master must either issue a stop condition during the ninth cycle or hold SDA HIGH during the ninth clock cycle and then issue a stop condition. YES Continue Normal Read or Write Command Sequence PROCEED Figure 12. Current Address Read Sequence Signals from the Master SDA Bus Signals from the Slave 11 S t a r t Slave Address S t o p 1 0 1 0 0 S1 S0 1 A C K Data FN8119.0 March 28, 2005 X40626 Random Read Random read operation allows the master to access any memory location in the array. Prior to issuing the Slave Address Byte with the R/W bit set to one, the master must first perform a “dummy” write operation. The master issues the start condition and the Slave Address Byte, receives an acknowledge, then issues the Word Address Bytes. After acknowledging receipts of the Word Address Bytes, the master immediately issues another start condition and the Slave Address Byte with the R/W bit set to one. This is followed by an acknowledge from the device and then by the eight bit word. The master terminates the read operation by not responding with an acknowledge and then issuing a stop condition. Refer to Figure 13 for the address, acknowledge, and data transfer sequence. Figure 13. Random Address Read Sequence Signals from the Master SDA Bus S T A R T Word Address Byte 1 Slave Address S T A R T Word Address Byte 0 S 1 0 1 0 0 S1 S0 0 S 1 0 1 0 0 S1 S0 1 A C K Signals from the Slave S T O P Slave Address A C K There is a similar operation, called “Set Current Address” where the device does no operation, but enters a new address into the address counter if a stop is issued instead of the second start shown in Figure 13. The device goes into standby mode after the stop and all bus activity will be ignored until a start is detected. The next Current Address Read operation reads from the newly loaded address. This operation could be useful if the master knows the next address it needs to read, but is not ready for the data. A C K P A C K Data The data output is sequential, with the data from address n followed by the data from address n + 1. The address counter for read operations increments through all page and column addresses, allowing the entire memory contents to be serially read during one operation. At the end of the address space the counter “rolls over” to address 0000H and the device continues to output data for each acknowledge received. Refer to Figure 14 for the acknowledge and data transfer sequence. Sequential Read Sequential reads can be initiated as either a current address read or random address read. The first Data Byte is transmitted as with the other modes; however, the master now responds with an acknowledge, indicating it requires additional data. The device continues to output data for each acknowledge received. The master terminates the read operation by not responding with an acknowledge and then issuing a stop condition. 12 FN8119.0 March 28, 2005 X40626 Figure 14. Sequential Read Sequence Signals from the Master SDA Bus Slave Address A C K S t o p A C K A C K S1 S0 1 A C K Signals from the Slave Data (1) Data (2) Data (n-1) Data (n) (n is any integer greater than 1) X40626 Addressing Slave Address Byte Following a start condition, the master must output a Slave Address Byte. This byte consists of several parts: – a device type identifier that is ‘1010’ to access the array – one bit of ‘0’. – next two bits are the device address. (S1 and S0) – After loading the entire Slave Address Byte from the SDA bus, the device compares the input slave byte data to the proper slave byte. Upon a correct compare, the device outputs an acknowledge on the SDA line. Word Address The word address is either supplied by the master or obtained from an internal counter. The internal counter is 00H on a power-up condition. The master must supply the two word address byte as shown in Figure 15. – one bit of the slave command byte is a R/W bit. The R/W bit of the Slave Address Byte defines the operation to be performed. When the R/W bit is a one, then a read operation is selected. A zero selects a write operation. Refer to Figure 15. 13 FN8119.0 March 28, 2005 X40626 Figure 15. X40626 Addressing Device Identifier 1 0 1 Device Select 0 0 S1 S0 R/W Slave Address Byte High Order Word Address A15 A14 A13 A12 A11 A10 A9 A8 A1 A0 D1 D0 Word Address Byte 1 Low Order Word Address A7 A6 A5 A4 A3 A2 Word Address Byte 0 D7 D6 D5 D4 D3 D2 Data Byte Operational Notes The device powers-up in the following state: – The device is in the low power standby state. – The WEL bit is set to ‘0’. In this state it is not possible to write to the device. – SDA pin is in the input mode. – Communication to the device is inhibited while RESET is active and any in-progress communication is terminated. – Block Lock bits can protect sections of the memory array from write operations. Symbol Table – RESET Signal is active for tPURST. WAVEFORM INPUTS OUTPUTS The following circuitry has been included to prevent inadvertent writes: Must be steady Will be steady – The WEL bit must be set to allow write operations. May change from LOW to HIGH Will change from LOW to HIGH May change from HIGH to LOW Will change from HIGH to LOW Don’t Care: Changes Allowed Changing: State Not Known N/A Center Line is High Impedance Data Protection – The proper clock count and bit sequence is required prior to the stop bit in order to start a nonvolatile write cycle. – A three step sequence is required before writing into the Control Register to change Watchdog Timer or Block Lock settings. – The WP pin, when held HIGH, and WPEN bit at logic HIGH will prevent all writes to the Control Register. 14 FN8119.0 March 28, 2005 X40626 ABSOLUTE MAXIMUM RATINGS COMMENT Temperature under bias ................... -65°C to +135°C Storage temperature ........................ -65°C to +150°C Voltage on any pin with respect to VSS... -1.0V to +7V D.C. output current (sink) ................................... 10mA Lead temperature (soldering, 10 seconds) ........ 300°C Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 2. Recommended Operating Conditions Temp Commercial Industrial Min. 0°C -40°C Max. 70°C +85°C D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.) VCC = 2.7 to 5.5V Symbol Parameter Min Max Unit Test Conditions VIL = VCC x 0.1, VIH = VCC x 0.9 fSCL = 400kHz, SDA = Open ICC1(1) Active Supply Current Read 1.0 mA ICC2(2) Active Supply Current Write 3.0 mA ISB1(2) Standby Current DC (WDT off) 1 µA VSDA=VSCL=VCC Others=GND or VCC ISB2(3) Standby Current DC (WDT on) 30 µA VSDA=VSCL=VCC Others=GND or VCC ILI Input Leakage Current 10 µA VIN = GND to VCC ILO Output Leakage Current 10 µA VSDA = GND to VCC Device is in Standby VIL Input LOW Voltage -1 VCC x 0.3 V VIH Input HIGH Voltage VCC x 0.7 VCC +0.5 V VHYS Schmitt Trigger Input Hysteresis Fixed input level VCC related level 0.2 .05 x VCC VOL Output LOW Voltage V V 0.4 V IOL = 1.0mA (VCC=3V) IOL = 3.0mA (VCC=5V) Notes: (1) The device enters the Active state after any start, and remains active until: (a) 9 clock cycles later if the Device Select Bits in the Slave Address Byte are incorrect; or (b) 200nS after a stop ending a read operation. (2) The device enters the Active state after any start, and remains active until tWC after a stop ending a write operation. (3) The device goes into Standby: (a) 200nS after any stop, except those that initiate a nonvolatile write cycle; or (b) tWC after a stop that initiates a nonvolatile cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in the Slave Address Byte. 15 FN8119.0 March 28, 2005 X40626 CAPACITANCE (TA = 25°C, f = 1.0 MHz, VCC = 5V) Symbol Parameter (4) COUT CIN (4) Max. Units Test Conditions Output Capacitance (SDA, RESET, V2FAIL) 8 pF VOUT = 0V Input Capacitance (SCL, WP, S0, S1) 6 pF VIN = 0V Notes: (4) This parameter is periodically sampled and not 100% tested. EQUIVALENT A.C. LOAD CIRCUIT 5V A.C. TEST CONDITIONS V2MON 1.53kΩ 1533Ω SDA RESET Input pulse levels 0.1VCC to 0.9VCC Input rise and fall times 10ns Input and output timing levels 0.5VCC Output load Standard Output Load V2FAIL 30pF 30pF A.C. CHARACTERISTICS (Over recommended operating conditions, unless otherwise specified) Symbol Parameter Min. Max. Units 400 kHz fSCL SCL Clock Frequency 0 tIN Pulse width Suppression Time at inputs 50 tAA SCL LOW to SDA Data Out Valid 0.1 tBUF Time the bus free before start of new transmission 1.3 µs tLOW Clock LOW Time 1.3 µs tHIGH Clock HIGH Time 0.6 µs tSU:STA Start Condition Setup Time 0.6 µs tHD:STA Start Condition Hold Time 0.6 µs tSU:DAT Data In Setup Time 100 ns tHD:DAT Data In Hold Time 0 µs tSU:STO Stop Condition Setup Time 0.6 µs tDH Data Output Hold Time 50 ns SDA and SCL Rise Time 20 + 0.1Cb(2) 300 ns 20 + 0.1Cb(2) 300 ns tR ns 0.9 µs tF SDA and SCL Fall Time tSU:WP WP Setup Time 0.6 µs tHD:WP WP Hold Time 0 µs Cb Capacitive load for each bus line 400 pF Notes: (1) Typical values are for TA = 25°C and VCC = 5.0V (2) Cb = total capacitance of one bus line in pF. 16 FN8119.0 March 28, 2005 X40626 TIMING DIAGRAMS Bus Timing tF tHIGH SCL tR tLOW tSU:DAT tSU:STA SDA IN tHD:DAT tHD:STA tSU:STO tAA tDH tBUF SDA OUT WP Pin Timing START SCL Clk 1 Clk 9 Slave Address Byte SDA IN tSU:WP WP tHD:WP Write Cycle Timing SCL SDA 8th bit of Last Byte ACK tWC Stop Condition Start Condition Nonvolatile Write Cycle Timing Symbol tWC Parameter (1) Write Cycle Time Min. Typ.(1) Max. Units 5 10 mS Notes: (1) tWC is the time from a valid stop condition at the end of a write sequence to the end of the self-timed internal nonvolatile write cycle. It is the minimum cycle time to be allowed for any nonvolatile write by the user, unless Acknowledge Polling is used. 17 FN8119.0 March 28, 2005 X40626 Power-Up and Power-Down Timing VTRIP/VTRIP2 VCC/V2MON tPURST 0 Volts tPURST tR tF tRPD VRVALID RESET/V2FAIL RESET Output Timing Symbol tPURST tRPD(8) tF(8) tR (8) VRVALID(8) VTRIP Range Parameter Power-up Reset Timeout VCC Detect to Reset/Output (Falling Edge) VCC/V2MON Fall Time VCC/V2MON Rise Time Reset Valid VCC or V2FAIL Valid V2MON Voltage Range over which VTRIP/VTRIP2 can be set Min. 100 Typ. 200 Max. 400 500 Units ms ns µs µs V V 100 100 1.0 2.0 VCC Notes: (8) This parameter is periodically sampled and not 100% tested. SDA vs. RESET Timing Start Start tRSP < tWDO SCL Timer Start SDA tRST tWDO tRST RESET Timer Start 18 Timer Restart FN8119.0 March 28, 2005 X40626 RESET Output Timing Symbol Parameter tWDO Watchdog Timeout Period, WD1 = 1, WD0 = 1 (factory setting) WD1 = 1, WD0 = 0 WD1 = 0, WD0 = 1 WD1 = 0, WD0 = 0 Reset Timeout tRST Min. Typ. Max. Units Disabled 100 450 1.0 Disabled 200 600 1.4 Disabled 400 850 2.0 Factory Setting ms ms sec 100 250 400 ms VTRIP Programming Timing Diagram (WEL = 1) VCC/V2MON VCC/V2MON (VTRIP/VTRIP2) tTSU tTHD VP WP tVPS tVPO 01 2 7 0 7 0 7 0 7 SCL data SDA AS1S000h Start 19 0001H*: set VTRIP 000DH: set VTRIP2 0003H: Resets VTRIP 000FH: Resets VTRIP2 00h tWC FN8119.0 March 28, 2005 X40626 Packaging Information 14-Lead Plastic Small Outline Gullwing Package Type S 0.150 (3.80) 0.228 (5.80) 0.158 (4.00) 0.244 (6.20) Pin 1 Index Pin 1 0.014 (0.35) 0.020 (0.51) 0.336 (8.55) 0.345 (8.75) (4X) 7° 0.053 (1.35) 0.069 (1.75) 0.004 (0.10) 0.010 (0.25) 0.050 (1.27) 0.010 (0.25) 0.020 (0.50) 0.050" Typical X 45° 0.050" Typical 0° - 8° 0.0075 (0.19) 0.010 (0.25) 0.250" 0.016 (0.410) 0.037 (0.937) FOOTPRINT 0.030" Typical 14 Places NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 20 FN8119.0 March 28, 2005 X40626 PACKAGING INFORMATION 14-Lead Plastic, TSSOP, Package Code V14 .025 (.65) BSC .169 (4.3) .252 (6.4) BSC .177 (4.5) .193 (4.9) .200 (5.1) .041 (1.05) .0075 (.19) .0118 (.30) .002 (.05) .006 (.15) .010 (.25) Gage Plane 0° - 8° Seating Plane .019 (.50) .029 (.75) Detail A (20X) .031 (.80) .041 (1.05) See Detail “A” NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 21 FN8119.0 March 28, 2005 X40626 Ordering Information VCC Range VTRIP Range VTRIP2 Range 4.5-5.5V 4.5-4.75 2.85-3.0 Package Operating Temperature Range Part Number RESET (Active LOW) Park Mark 14L SOIC 0°C-70°C X40626S14-4.5A AL -40°C-85°C X40626S14I-4.5A AM 0°C-70°C X40626V14-4.5A AL -40°C-85°C X40626V14I-4.5A AM 14L TSSOP 4.5-5.5V 4.25-4.5 2.85-3.0 14L SOIC 14L TSSOP 2.7-5.5V 2.85-3.0 2.15-2.30 14L SOIC 14LTSSOP 2.7-5.5V 2.55-2.7 2.55-2.7 14L SOIC 14L TSSOP 0°C-70°C X40626S14 blank -40°C-85°C X40626S14I I 0°C-70°C X40626V14 blank -40°C-85°C X40626V14I I 0°C-70°C X40626S14-2.7A AN -40°C-85°C X40626S14I-2.7A AP 0°C-70°C X40626V14-2.7A BN -40°C-85°C X40626V14I-2.7A AP 0°C-70°C X40626S14-2.7 F -40°C-85°C X40626S14I-2.7 G 0°C-70°C X40626V14-2.7 F -40°C-85°C X40626V14I-2.7 G PART MARK INFORMATION 14-Lead SOIC/TSSOP X40626 X YYWWXX S = SOIC V = TSSOP XX – Part Mark WW – Workweek YY – Year All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 22 FN8119.0 March 28, 2005