678D Datasheet

678D
www.vishay.com
Vishay Sprague
Aluminum Capacitors
105 °C, Miniature, Radial Lead
FEATURES
• Improved SMPS output capacitors
• Highest ripple current ratings per case size
Available
• High CV
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
RIPPLE CURRENT MULTIPLIERS
QUICK REFERENCE DATA
DESCRIPTION
TEMPERATURE
VALUE
Nominal case size 
Ø D x L in inches [mm]
0.394 x 0.472 [10.0 x 12.0]
to 0.709 x 1.575 [18.0 x 40.0]
AMBIENT TEMPERATURE
+105 °C
1.0
Operating temperature
- 55 °C to +105 °C
+85 °C
2.2
Rated capacitance range, CR
Tolerance on CR
Rated voltage range, UR
Termination
Life validation test at 105 °C
Shelf life at 105 °C
DC leakage current
Revision: 19-Oct-15
MULTIPLIERS
33 μF to 6800 μF
+75 °C
2.7
± 20 %
 +65 °C
3.0
6.3 WVDC to 63 WVDC
FREQUENCY (Hz)
2 and 3 radial leads and axial
mount.
WVDC 50 TO 60 100 TO 120 300 TO 400 1K TO 19K 20K TO 200K
4000 h (0.512" [13.0] diameter):
3000 h (0.394" [10.0] diameter):
CAP  20 % (6.3 WVDC to
25 WVDC),
 15 % (40 WVDC to 63 WVDC)
from initial measurement.
ESR  1.3 x initial
specified limit.
DCL  2 x initial specified limit.
1000 h: CAP  20 %
(6.3 WVDC to 25 WVDC),
 15 % (40 WVDC to 63 WVDC)
from initial measurements.
ESR  1.3 x initial
specified limit.
I = 0.01 CV (2 min charge time)
I = 0.03 CV (1 min charge time)
I in μA, C in μF, V in Volts
6.3 to 63
0.60
0.70
0.75
0.82
1.0
LOW TEMPERATURE PERFORMANCE
CAPACITANCE RATIO C-55 °C/C+25 °C MINIMUM AT 120 Hz
MAXIMUM 
CAPACITANCE 
CHANGE
MAXIMUM 
IMPEDANCE
CHANGE
VOLTAGE
MULTIPLIER
6.3 V to 16 V
0.75
25 V to 63 V
0.85
VOLTAGE
MULTIPLIER
6.3 V to 16 V
2.0
25 V to 63 V
1.5
ESL (TYPICAL VALUES AT 1 MHz TO 10 MHz)
NOMINAL
DIAMETER
TYPICAL ESL (nH)
0.394
[10.0]
0.512
[13.0]
0.630
[16.0]
0.709
[18.0]
4.0
7.0
10.0
12.0
Document Number: 42055
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
678D
www.vishay.com
Vishay Sprague
BULK SPECIFICATIONS in millimeters
TERMINAL CODE C
TERMINAL CODE D
9.5 min.
S
W
L
20 min.
S
+
D
L
W
+
D
-
-
15 min.
Sleeve
7.1 min.
Sleeve
TERMINAL CODE O (2)
TERMINAL CODE J (1)
9.5 ± 1.6
25 min.
S
W
L
S
25 min.
T
+
D
+
D
-
NC
-
NC
25 min.
L
W
5.0 ± 1.6
Sleeve
Third lead may fall
within ± 20° of CL
Sleeve
7.1 ± 1.6
Notes
+ Positive terminal
- Negative terminal
NC
No charge potential
(1) Available for 12.5 mm, 16 mm, and 18 mm diameter units
(2) Available for 12.5 mm, 16 mm, and 18 mm diameter units with epoxy end-seal
DIMENSIONS in inches [millimeters]
NOMINAL
CASE
CODE
D
STYLES 2 AND 4
L
D (max.)
L (max.)
STYLES 3 AND 5
D (max.)
L (max.)
LEAD SPACING
S ± 0.024
[0.60]
LEAD DIAMETER
T ± 0.020
[0.50]
NOMINAL
AWG
CC
0.394 [10.0] 0.512 [13.0] 0.413 [10.5] 0.563 [14.3] 0.413 [10.5] 0.630 [16.0] 0.197 [5.0]
n/a
0.025 [0.63]
22
CD
0.394 [10.0] 0.630 [16.0] 0.413 [10.5] 0.669 [17.0] 0.413 [10.5] 0.740 [18.8] 0.197 [5.0]
n/a
0.025 [0.63]
22
CG
0.394 [10.0] 0.787 [20.0] 0.413 [10.5] 0.846 [21.5] 0.413 [10.5] 0.906 [23.0] 0.197 [5.0]
n/a
0.025 [0.63]
22
DG
0.492 [12.5] 0.787 [20.0] 0.512 [13.0] 0.846 [21.5] 0.512 [13.0] 0.906 [23.0] 0.197 [5.0] 0.098 [2.5]
0.032 [0.81]
20
DK
0.492 [12.5] 0.984 [25.0] 0.512 [13.0] 1.043 [26.5] 0.512 [13.0] 1.142 [29.0] 0.197 [5.0] 0.098 [2.5]
0.032 [0.81]
20
DM
0.492 [12.5] 1.043 [26.5] 0.512 [13.0] 1.102 [28.0] 0.512 [13.0] 1.161 [29.5] 0.197 [5.0] 0.098 [2.5]
0.032 [0.81]
20
DT
0.492 [12.5] 1.319 [33.5] 0.512 [13.0] 1.346 [34.2] 0.512 [13.0] 1.417 [36.0] 0.197 [5.0] 0.098 [2.5]
0.032 [0.81]
20
DS
0.492 [12.5] 1.673 [42.5] 0.512 [13.0] 1.720 [43.7] 0.512 [13.0] 1.791 [45.5] 0.197 [5.0] 0.098 [2.5]
0.032 [0.81]
20
EK
0.630 [16.0] 0.984 [25.0] 0.650 [16.5] 1.031 [26.2] 0.650 [16.5] 1.098 [27.9] 0.295 [7.5] 0.150 [3.8]
0.032 [0.81]
20
EN
0.630 [16.0] 1.260 [32.0] 0.650 [16.5] 1.319 [33.5] 0.650 [16.5] 1.417 [36.0] 0.295 [7.5] 0.150 [3.8]
0.032 [0.81]
20
ER
0.630 [16.0] 1.417 [36.0] 0.650 [16.5] 1.476 [37.5] 0.650 [16.5] 1.575 [40.0] 0.295 [7.5] 0.150 [3.8]
0.032 [0.81]
20
EU
0.630 [16.0] 1.575 [40.0] 0.650 [16.5] 1.642 [41.7] 0.650 [16.5] 1.669 [42.4] 0.295 [7.5] 0.150 [3.8]
0.032 [0.81]
20
FR
0.709 [18.0] 1.417 [36.0] 0.728 [18.5] 1.476 [37.5] 0.728 [18.5] 1.575 [40.0] 0.295 [7.5] 0.150 [3.8]
0.032 [0.81]
20
FV
0.709 [18.0] 1.575 [40.0] 0.728 [18.5] 1.653 [42.0] 0.728 [18.5] 1.693 [43.0] 0.295 [7.5] 0.150 [3.8]
0.032 [0.81]
20
Revision: 19-Oct-15
Document Number: 42055
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
678D
www.vishay.com
Vishay Sprague
TAPE AND REEL, SPECIFICATIONS TO EIA-468D in inches [millimeters]
P
Formed Leads
K
H
H0
F
W0 W
L1
P0
d
D0
DIMENSIONS in inches [millimeters] AND PACKAGING QUANTITIES
CASE SIZE
F LEAD SPACING
STD. QTY/REEL
0.236 x 0.453 [6.0 x 11.0]
0.197 [5.0]
800
0.315 x 0.472 [8.0 x 12.0]
0.197 [5.0]
700
Unformed (Straight) Leads
P
H
F
W0 W
L1
P0
d
D0
f
DIMENSIONS in inches [millimeters] AND PACKAGING QUANTITIES
CASE SIZE
F LEAD SPACING
STD. QTY/REEL
0.236 x 0.453 [6.0 x 11.0]
0.098 [2.5]
800
0.315 x 0.472 [8.0 x 12.0]
0.140 (1) [3.5]
700
0.394 x 0.512 [10.0 x 13.0]
0.197 [5.0]
500
0.394 x 0.630 [10.0 x 16.0]
0.197 [5.0]
500
0.394 x 0.787 [10.0 x 20.0]
0.197 [5.0]
500
Note
(1) Available as special order.
Revision: 19-Oct-15
Document Number: 42055
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
678D
www.vishay.com
Vishay Sprague
DIMENSIONS in inches [millimeters]
ITEM
d - Lead-wire diameter
P - Pitch of component
P0 - Feed hole pitch
F - Lead-to-lead distance
K - Clinch height
H - Height of component from tape center
H0 - Lead-wire clinch height
W - Tape width
W0 - Hold down tape width
D0 - Feed hole diameter
t - Total tape thickness
L1 - Maximum lead protrusion
0.236 x 0.433
[6.0 x 11.0]
0.025 [0.63]
0.500 [12.7]
0.500 [12.7]
0.197 [5.0]
0.098 [2.5]
0.728 [18.5]
0.630 [16.0]
0.709 [18.0]
0.591 [15.0]
0.157 [4.0]
0.028 [0.7]
0.118 [3.0]
CASE SIZE (DIAMETER x LENGTH)
0.315 x 0.472
0.394 x 0.512
0.394 x 0.630
[8.0 x 12.0]
[10.0 x 13.0]
[10.0 x 16.0]
0.025 [0.63]
0.025 [0.63]
0.025 [0.63]
0.500 [12.7]
0.500 [12.7]
0.500 [12.7]
0.500 [12.7]
0.500 [12.7]
0.500 [12.7]
0.197 [5.0]
0.197 [5.0]
0.197 [5.0]
0.157 [4.0]
n/a
n/a
0.787 [20.0]
0.906 [23.0]
0.906 [23.0]
0.630 [16.0]
n/a
n/a
0.709 [18.0]
0.709 [18.0]
0.709 [18.0]
0.591 [15.0]
0.591 [15.0]
0.591 [15.0]
0.157 [4.0]
0.157 [4.0]
0.157 [4.0]
0.028 [0.7]
0.028 [0.7]
0.028 [0.7]
0.118 [3.0]
0.118 [3.0]
0.118 [3.0]
0.394 x 0.787
[10.0 x 20.0]
0.025 [0.63]
0.500 [12.7]
0.500 [12.7]
0.197 [5.0]
n/a
0.906 [23.0]
n/a
0.709 [18.0]
0.591 [15.0]
0.157 [4.0]
0.028 [0.7]
0.118 [3.0]
Note
• Terminal code “I” = tape and reel. Terminal code “+” = tape and ammo. 
Positive leader is standard. Negative leader is available by special order.
ORDERING EXAMPLE
Electrolytic capacitor 678D series: 678D 108 M 6R3 DG 3 D
DESCRIPTION
CODE
678D
108
M
6R3
DG
3
D
EXPLANATION
Product type
Capacitance value (1000 μF)
Tolerance (M = ± 20 %)
Voltage rating at 105 °C (6R3 = 6.3 V)
Can size (see Dimensions table)
Sleeve and sealing (3 = P.V.C. sleeve w/epoxy end seal)
Terminal code/packaging (D = bulk; straight leads)
Note
• For lead (Pb)-free / RoHS compliant products add suffix “E3” to part number.
Example: 678D108M6R3DG3DE3
ELECTRICAL DATA AND ORDERING INFORMATION
CAPACITANCE
(μF)
PART NUMBER
330.0
470.0
1000.0
2200.0
3300.0
4700.0
678D337M6R3CC3D
678D477M6R3CD3D
678D108M6R3DG3D
678D228M6R3EK3D
678D338M6R3DS3D
678D478M6R3FR3D
330.0
470.0
1000.0
2200.0
3300.0
4700.0
678D337M010CD3D
678D477M010CG3D
678D108M010DM3D
678D228M010EK3D
678D338M010EN3D
678D487M010FR3D
Revision: 19-Oct-15
NOMINAL CASE SIZE
DxL
MAX. ESR
AT +25 °C ()
20 Hz
6.3 WVDC at 105 °C, SURGE = 9 V
0.394 x 0.512 [10.0 x 13.0]
0.540
0.394 x 0.630 [10.0 x 16.0]
0.340
0.492 x 0.787 [12.5 x 20.0]
0.200
0.630 x 0.984 [16.0 x 25.0]
0.110
0.492 x 1.673 [12.5 x 42.5]
0.067
0.709 x 1.417 [18.0 x 36.0]
0.066
10 WVDC AT 105 °C, SURGE = 13 V
0.394 x 0.630 [10.0 x 16.0]
0.350
0.394 x 0.787 [10.0 x 20.0]
0.235
0.492 x 1.043 [12.5 x 26.5]
0.120
0.630 x 0.984 [16.0 x 25.0]
0.115
0.630 x 1.260 [16.0 x 32.0]
0.085
0.709 x 1.417 [18.0 x 36.0]
0.070
MAX. RIPPLE
AT +105 °C (A)
20 kHz
20 kHz to 100 kHz
MAX.
IMPEDANCE
AT +25 °C ()
100 kHz
0.213
0.133
0.071
0.041
0.031
0.029
0.36
0.49
0.83
1.36
1.67
2.02
0.213
0.132
0.070
0.045
0.032
0.031
0.135
0.092
0.062
0.042
0.038
0.031
0.46
0.63
0.98
1.52
1.56
1.97
0.134
0.090
0.061
0.046
0.041
0.033
Document Number: 42055
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
678D
www.vishay.com
Vishay Sprague
ELECTRICAL DATA AND ORDERING INFORMATION
NOMINAL CASE SIZE
DxL
MAX. ESR
AT +25 °C ()
MAX. RIPPLE
AT +105 °C (A)
MAX.
IMPEDANCE
AT +25 °C ()
100 kHz
CAPACITANCE
(μF)
PART NUMBER
220.0
678D227M016CC3D
0.394 x 0.512 [10.0 x 13.0]
0.585
0.217
0.40
0.217
330.0
678D337M016CD3D
0.394 x 0.630 [10.0 x 16.0]
0.370
0.137
0.52
0.136
20 Hz
20 kHz
20 kHz to 100 kHz
16 WVDC AT 105 °C, SURGE = 20 V
470.0
678D477M016CG3D
0.394 x 0.787 [10.0 x 20.0]
0.250
0.098
0.70
0.094
1000.0
678D108M016DM3D
0.492 x 1.043 [12.5 x 26.5]
0.130
0.066
1.00
0.065
2200.0
678D228M016ER3D
0.630 x 1.417 [16.0 x 36.0]
0.074
0.032
1.78
0.034
3300.0
678D338M016FR3D
0.709 x 1.417 [18.0 x 36.0]
0.074
0.032
1.94
0.034
220.0
678D227M020CD3D
0.394 x 0.630 [10.0 x 16.0]
0.380
0.150
0.41
0.148
330.0
678D337M020CG3D
0.394 x 0.787 [10.0 x 20.0]
0.270
0.100
0.61
0.098
470.0
678D477M020DG3D
0.492 x 0.787 [12.5 x 20.0]
0.250
0.077
0.45
0.075
1000.0
678D108M020DT3D
0.492 x 1.280 [12.5 x 33.5]
0.115
0.048
0.78
0.045
2200.0
678D228M020ER3D
0.630 x 1.417 [16.0 x 36.0]
0.077
0.032
1.80
0.034
3300.0
678D338M020FV3D
0.709 x 1.575 [18.0 x 40.0]
0.061
0.026
2.25
0.028
0.250
20 WVDC AT 105 °C, SURGE = 30 V
25 WVDC AT 105 °C, SURGE = 35 V
100.0
678D107M025CC3D
0.394 x 0.512 [10.0 x 13.0]
0.700
0.250
0.32
220.0
678D227M025CG3D
0.394 x 0.787 [10.0 x 20.0]
0.300
0.105
0.59
0.100
330.0
678D337M025DG3D
0.492 x 0.787 [12.5 x 20.0]
0.270
0.078
0.79
0.076
0.068
470.0
678D477M025DM3D
0.492 x 1.043 [12.5 x 26.5]
0.160
0.067
0.97
1000.0
678D108M025DS3D
0.492 x 1.673 [12.5 x 42.5]
0.090
0.034
1.60
0.036
2200.0
678D228M025FV3D
0.709 x 1.575 [18.0 x 40.0]
0.062
0.026
2.22
0.028
47.0
678D476M040CC3D
0.394 x 0.512 [10.0 x 13.0]
0.265
0.28
0.265
40 WVDC AT 105 °C, SURGE = 55 V
0.950
100.0
678D107M040CD3D
0.394 x 0.630 [10.0 x 16.0]
0.580
0.165
0.38
0.165
330.0
678D337M040DM3D
0.492 x 1.043 [12.5 x 26.5]
0.200
0.068
0.93
0.070
470.0
678D477M040EK3D
0.630 x 0.984 [16.0 x 25.0]
0.133
0.046
1.28
0.050
1000.0
678D108M040ER3D
0.630 x 1.417 [16.0 x 36.0]
0.080
0.033
1.76
0.035
0.275
50 WVDC AT 105 °C, SURGE = 75 V
47.0
678D476M050CC3D
0.394 x 0.512 [10.0 x 13.0]
1.250
0.275
0.28
100.0
678D107M050CG3D
0.394 x 0.787 [10.0 x 20.0]
0.520
0.115
0.57
0.112
220.0
678D227M050DM3D
0.472 x 1.043 [12.5 x 26.5]
0.240
0.069
0.93
0.071
330.0
678D337M050EK3D
0.630 x 0.984 [16.0 x 25.0]
0.150
0.048
1.26
0.052
470.0
678D477M050DS3D
0.492 x 1.673 [12.5 x 42.5]
0.110
0.036
1.55
0.039
1000.0
678D108M050FV3D
0.709 x 1.575 [18.0 x 40.0]
0.077
0.028
2.15
0.032
33.0
678D336M063CC3D
0.394 x 0.512 [10.0 x 13.0]
1.600
0.288
0.27
0.288
47.0
678D476M063CD3D
0.394 x 0.630 [10.0 x 16.0]
1.000
0.180
0.37
0.180
100.0
678D107M063DG3D
0.492 x 0.787 [12.5 x 20.0]
0.450
0.093
0.72
0.090
220.0
678D227M063DT3D
0.492 x 1.280 [12.5 x 33.5]
0.160
0.055
1.10
0.054
220.0
678D227M063EK3D
0.630 x 0.984 [16.0 x 25.0]
0.170
0.050
1.23
0.054
330.0
678D337M063DS3D
0.492 x 1.673 [12.5 x 42.5]
0.130
0.038
1.51
0.040
470.0
678D477M063ER3D
0.630 x 1.417 [16.0 x 36.0]
0.120
0.035
1.70
0.038
63 WVDC AT 105 °C, SURGE = 80 V
Revision: 19-Oct-15
Document Number: 42055
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Similar pages