EVB-LAN9500A-MII Evaluation Board User Manual - EVB-LAN9500A-MII Evaluation Board User Manual

EVB-LAN9500A-MII Evaluation Board User Manual
Copyright © 2012 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information
sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed
for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office
to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor
devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms
and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement").
The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets
are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure
could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing
and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained
by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and company
names are the trademarks of their respective holders.
The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES
ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT,
SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM
OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE;
WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
SMSC LAN9500A
USER MANUAL
Revision 1.0 (12-04-12)
LAN9500A Evaluation Board User Manual
1 Introduction
The LAN9500A is a high performance, small form factor solution for USB to 10/100 Ethernet port
bridging. With applications ranging from embedded systems, set-top boxes, and PVR’s, to USB port
replicators, USB to Ethernet adapters, PC docking stations, and test instrumentation, the LAN9500A
is targeted as a high performance, low cost USB/Ethernet connectivity solution.
The LAN9500A contains an integrated 10/100 Ethernet PHY, USB PHY, Hi-Speed USB 2.0 device
controller, 10/100 Ethernet MAC, TAP controller, EEPROM controller, and a FIFO controller with a total
of 30 KB of internal packet buffering. The LAN9500A complies with the IEEE 802.3 (full/half-duplex
10BASE-T and 100BASE-TX) Ethernet protocol and USB 2.0 specification, enabling compatibility with
industry standard Fast Ethernet and USB 2.0 applications.
The EVB-LAN9500A-MII is an Evaluation Board (EVB) that utilizes the LAN9500A to provide a fully
functional, USB to Ethernet interface. The EVB-LAN9500A-MII provides fully integrated Ethernet and
USB ports via the onboard RJ45 and USB Type B connectors. The EVB-LAN9500A-MII can be
configured for bus- or self-powered operation and supports internal and external PHY modes. An
external PHY may be connected via the onboard 40-pin female MII connector. The onboard 256x8
EEPROM is used to load the EVB-LAN9500A-MII’s USB configuration parameters and MAC address.
LAN9500A software drivers are available for Windows XP, Windows Vista, Mac OS X, Linux, and
Windows CE. Additional manufacturing and diagnostic tools are available for debugging and external
EEPROM configuration. For complete details, refer to the “LAN9500A Software User Manual”.
A simplified block diagram of the EVB-LAN9500A-MII can be seen in Figure 1.1.
External PHY
JTAG Header
2 x 20
256 x 8
µWire
EEPROM
USB
40-Pin MII Connector
(Female)
SMSC
LAN9500A
USB Type B
Connector
10/100
Ethernet
Magnetics
& RJ45
Ethernet
1 x 10
GPIO Header
EVB-LAN9500A-MII
Figure 1.1 EVB-LAN9500A-MII Block Diagram
Revision 1.0 (12-04-12)
USER MANUAL
2
SMSC LAN9500A
LAN9500A Evaluation Board User Manual
1.1
References
Concepts and material available in the following documents may be helpful when using the EVBLAN9500A-MII.
Table 1.1 References
DOCUMENT
LOCATION
SMSC LAN9500A Datasheet
http://www.smsc.com/lan9500a
AN8-13 Suggested Magnetics
http://www.smsc.com/lan9500a
SMSC EVB-LAN9500A-MII Evaluation Board Schematic
http://www.smsc.com/lan9500a
SMSC LAN9500A Software User Manual
http://www.smsc.com/lan9500a
2 Board Details
This section includes the following EVB-LAN9500A-MII board details:
2.1

Configuration

Mechanicals
Configuration
The following sub-sections describe the various board features including jumpers, LEDs, test points,
and system connections. A top view of the EVB-LAN9500A-MII is shown in Figure 2.1.
SMSC LAN9500A
USER MANUAL
3
Revision 1.0 (12-04-12)
LAN9500A Evaluation Board User Manual
GPIO/Strap
Header
Female MII
Connector
Reset
Switch
MII
Testpoints
JP2
JP3 –
JP6
J5
JTAG
Header
JP7
LAN9500A
JP1
+5V Power
Input
USB Type B
Connector
Ethernet Port
(integrated LEDs)
Figure 2.1 EVB-LAN9500A-MII Top View
Note: The EVB-LAN9500A-MII includes a 2A fuse (F1) to protect from overcurrent conditions. If this
fuse becomes damaged, it can be replaced with a 2A Littlefuse-154002.
2.1.1
Jumpers
The following table details the jumper definitions and default settings for the EVB-LAN9500A-MII.
Jumper settings may be changed as needed. However, any deviation from the default settings should
be approached with care and knowledge of the schematics and datasheet. An incorrect jumper setting
may disable the board.
Note: A dashed line in the Settings column indicates an installed jumper. All jumper settings are
shown in their default state (self-powered, internal Ethernet PHY operation).
Table 2.1 Jumpers
JUMPER
DESCRIPTION
JP2
JTAG Header Connect
JP3
Ethernet PHY Select
Revision 1.0 (12-04-12)
SETTINGS
1
2
IN: Connects shared JTAG signals to
JTAG header J2
OUT: Disconnects shared JTAG signals
from JTAG header J2
1
2
Selects external Ethernet PHY
2---3
USER MANUAL
4
Selects internal LAN9500A Ethernet PHY
SMSC LAN9500A
LAN9500A Evaluation Board User Manual
Table 2.1 Jumpers (continued)
JUMPER
JP4
DESCRIPTION
SETTINGS
MII Connector +5V Select
1
2
IN: Onboard +5V supplied to MII
connector pins 1, 20, 21, and 40
OUT: Onboard +5V not supplied to MII
connector pins 1, 20, 21, and 40
1
2
Populate when bus-powered. Connects
VCC_USB from the upstream host USB
connector to the onboard +3.3V voltage
regulator input.
+5V Power Supply Select
(Note 2.1)
JP5
Onboard +3.3V Regulator
Output Connect
(Note 2.2)
JP6
2---3
Populate when self-powered. Connects
+5V from the external power supply to
the onboard +3.3V voltage regulator
input.
1---2
IN: Connects output of onboard +3.3V
regulator to the +3.3V power plane
OUT: Disconnects output of onboard
+3.3V regulator from the +3.3V power
plane
1
Populate when bus-powered. Connects
+3.3V voltage regulator output to
VBUS_DET.
2
VBUS_DET Input Select
(Note 2.1)
JP7
Populate when self-powered. Connects
VCC_USB from the upstream host USB
connector to VBUS_DET through a
voltage divider and transient filter.
2---3
2.1.2
Note 2.1
JP5 and JP7 must be populated indentically.
Note 2.2
This jumper should only be removed if the customer supplies +3.3V from an external
source.
LEDs
Table 2.2 LEDs
REFERENCE
COLOR
INDICATION
LED1
Green
LED2
Green
Note:
T1
Green
Ethernet Link/Activity
Solid: Link established
Blinking: Link activity
OFF: No link
T1
Yellow
Ethernet Speed
ON: 100BASE-TX
OFF: 10BASE-T
Ethernet Full Duplex
+5V External Power Active
SMSC LAN9500A
USER MANUAL
5
This LED will not illuminate when in
bus-powered mode.
Revision 1.0 (12-04-12)
LAN9500A Evaluation Board User Manual
2.1.3
Test Points
Table 2.3 Test Points
TEST POINT
DESCRIPTION
CONNECTION
TP2
TDO/nPHY_RST Pin of LAN9500A
(unpopulated)
TDO/nPHY_RST
TP3
nRESET Pin of LAN9500A (Unpopulated)
nRESET
TP4
+3.3V Test Point (Unpopulated)
(Note 2.3)
PIN 1: +3.3V
PIN 2: GND
Note 2.3
2.1.4
Pin 1 of this test point can be used by the customer to provide an external +3.3V supply.
This option may be useful in cases where the customer desires operation in self-powered
permanently attached mode. If used in this fashion, JP6 must be removed.
System Connections
Table 2.4 System Connections
PLUG/HEADER
DESCRIPTION
PART
P1
USB Type B Right Angle Connector
AMP 292304-1
P2
+5V Power Supply Barrel Connector
CUI PJ-102AH
T1
RJ45 Ethernet Port with Integrated
Magnetics & LEDs
Pulse J0011D01B
1x2 nPHY_INT Header
JP1
J2
PIN 1: nPHY_INT
PIN 2: Ground
Note:
2x10 JTAG Header for IEEE 1149.1
Compliant TAP Controller
Note:
J3
In internal PHY mode, nPHY_INT is
a configurable output. In external
PHY mode, nPHY_INT is an input
Adam Tech PH2-20-U-A
Refer Table 2.5 to for a full pin list.
1x10 GPIO/Strap Header
Note:
Adam Tech PH1-2-U-A
Refer Table 2.6 to for a full pin list.
Adam Tech PH1-10-U-A
40-pin Female MII Connector
J4
Revision 1.0 (12-04-12)
Note:
This connector follows the
standardized MII pinout. Refer to
the EVB-LAN9500A-MII schematic
for additional information.
USER MANUAL
6
AMP 5787170-4
SMSC LAN9500A
LAN9500A Evaluation Board User Manual
Table 2.4 System Connections (continued)
PLUG/HEADER
DESCRIPTION
PART
1x2 External Reset Header
J5
Adam Tech PH1-2-U-A
PIN 1: GND
PIN 2: Reset Generator Input
2x11 MII Test Point Header
J6
Note:
Refer Table 2.7 to for a full pin list
Adam Tech PH2-22-U-A
.
Table 2.5 2x10 JTAG Header Pinout
HEADER PIN
DESCRIPTION
HEADER PIN
DESCRIPTION
1
nTRST
11
No Connect
2
Ground
12
Ground
3
TDO
13
No Connect
4
Ground
14
Ground
5
TDI
15
No Connect
6
Ground
16
Ground
7
TMS
17
No Connect
8
Ground
18
Ground
9
TCK
19
No Connect
10
Ground
20
+3.3V
.
Table 2.6 1x10 GPIO/Strap Header Pinout
HEADER PIN
DESCRIPTION
HEADER PIN
DESCRIPTION
1
+3.3V
6
TXD0/GPIO4/EEP_DISABLE
2
COL/GPIO0
7
TXD1/GPIO5/RMT_WKP
3
MDIO/GPIO1
8
TXD2/GPIO6/PORT_SWAP
4
MDC/GPIO2
9
TXD3/GPIO7/EEP_SIZE
5
CRS/GPIO3
10
Ground
SMSC LAN9500A
USER MANUAL
7
Revision 1.0 (12-04-12)
LAN9500A Evaluation Board User Manual
.
Table 2.7 2x11 MII Header Pinout
HEADER PIN
DESCRIPTION
HEADER PIN
DESCRIPTION
1
Ground
12
TXER (Ground)
2
Ground
13
TXCLK
3
MDIO/GPIO1
14
TXEN
4
MDC/GPIO2
15
TXD0/GPIO4/EEP_DISABLE
5
TDI/RXD3
16
TXD1/GPIO5/RMT_WKP
6
TMS/RXD2
17
TXD2/GPIO6/PORT_SWAP
7
TCK/RXD1
18
TXD3/GPIO7/EEP_SIZE
8
nTRST/RXD0
19
COL/GPIO0
9
RXDV
20
CRS/GPIO3
10
RXCLK
21
Ground
11
RXER
22
Ground
2.1.5
Switches
Table 2.8 Switches
SWITCH
S1
Revision 1.0 (12-04-12)
DESCRIPTION
FUNCTION
Reset switch
When pressed, triggers a board reset
USER MANUAL
8
SMSC LAN9500A
LAN9500A Evaluation Board User Manual
2.2
Mechanicals
Figure 2.2 details the EVB-LAN9500A-MII mechanical dimensions.
0.675
0.2
0.225
0.225
2.075
Ø0.125
Ø0.125
TOP VIEW
Ø0.125
Ø0.125
0.225
0.225
0.675
0.2
3.100
Figure 2.2 EVB-LAN9500A-MII Mechanicals
SMSC LAN9500A
USER MANUAL
9
Revision 1.0 (12-04-12)
LAN9500A Evaluation Board User Manual
3 Revision History
Table 3.1 Revision History
REVISION LEVEL & DATE
SECTION/FIGURE/ENTRY
CORRECTION
Rev. 1.0 (12-04-12)
Document co-branded: Microchip logo added, modification to legal disclaimer.
Rev. 1.0 (02-02-10)
Initial Release
Revision 1.0 (12-04-12)
USER MANUAL
10
SMSC LAN9500A