A5977 Datasheet

A5977
Microstepping DMOS Driver with Translator
FEATURES AND BENEFITS
•
•
•
•
•
•
•
•
•
•
•
•
±2.8 A, 40 V output rating
Low RDS(on) outputs, 0.22 Ω source, 0.15 Ω sink typical
Automatic current decay mode detection/selection
3 to 5.5 V logic supply voltage range
Mixed, fast, and slow current decay modes
Home output
Synchronous rectification for low power dissipation
Internal UVLO and thermal shutdown circuitry
Crossover-current protection
Short-to-ground protection
Short-to-VBB protection
Shorted load protection
Package: 28-lead TSSOP (suffix LP) with
exposed thermal pad
DESCRIPTION
The A5977 is a complete microstepping motor driver with
built-in translator. It is designed to operate bipolar stepper
motors in full-, half-, quarter-, and eighth-step modes, with
output drive capability of 40 V and ±2.8 A. The A5977 includes
a fixed off-time current regulator that has the ability to operate in
slow-, fast-, or mixed-decay modes. This current-decay control
scheme results in reduced audible motor noise, increased step
accuracy, and reduced power dissipation.
The translator is the key to the easy implementation of the
A5977. Simply inputting one pulse on the STEP input drives the
motor one step (two logic inputs determine if it is a full-, half-,
quarter-, or eighth-step). There are no phase sequence tables,
high-frequency control lines, or complex interfaces to program.
The A5977 interface is an ideal fit for applications where a
complex microprocessor is unavailable or overburdened.
Internal synchronous rectification control circuitry is provided
to improve power dissipation during PWM operation. Internal
circuit protection includes thermal shutdown with hysteresis,
undervoltage lockout (UVLO), and crossover-current
protection. Special power-up sequencing is not required.
The A5977 is supplied in a thin (<1.2 mm) 28-pin TSSOP
with an exposed thermal pad (suffix LP). The package is lead
(Pb) free (suffix -T), with 100% matte-tin leadframe plating.
Not to scale
Typical Application
Logic
Supply
CP1
VDD
CP2
VCP
REF
PFD
Load
Supply
VBB1
VBB2
Microcontroller
or
Controller Logic
HOMEn
STEP
DIR
RESETn
SLEEPn
ENABLEn
MS1
MS2
SR
RC1
RC2
VREG
A5977-DS, Rev. 2
A5977
OUT1A
OUT1B
SENSE1
SENSE2
OUT2A
OUT2B
GND
PGND
100 µF
A5977
Microstepping DMOS Driver with Translator
SELECTION GUIDE
Part Number
Package
Packing
A5977GLPTR-T
28-pin TSSOP
4000 pieces per reel
SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Load Supply Voltage
VBB
Logic Supply Voltage
VDD
Logic Input Voltage Range
SENSEx Voltage (DC)
VIN
40
V
7
V
Pulsed, tW > 30 ns
–0.3 to VDD + 0.3
V
Pulsed, tW < 30 ns
–1 to VDD + 1
V
VSENSE
0.5
V
Reference Voltage
VREF
VDD
V
Output Current
IOUT
±2.8
A
–40 to 105
°C
Operating Ambient Temperature
TA
Output current rating may be limited by duty cycle,
ambient temperature, and heat sinking. Under any set of
conditions, do not exceed the specified current rating or a
junction temperature of 150°C.
Range G
Junction Temperature
TJ(max)
150
°C
Storage Temperature
Tstg
–55 to 150
°C
THERMAL CHARACTERISTICS: May require derating at maximum conditions; see application information
Characteristic
Symbol
Package Thermal Resistance
RθJA
Test Conditions*
Package LP, on 4-layer PCB based on JEDEC standard
Value
Units
28
ºC/W
*Additional thermal information available on Allegro website.
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
2
A5977
Microstepping DMOS Driver with Translator
PINOUT DIAGRAM AND TERMINAL LIST TABLE
Terminal List Table
Number
Name
1
SENSE1
Sense resistor for bridge 1
25 OUT1B
2
HOMEn
Logic output
PFD 5
24 CP2
3
DIR
RC1 6
23 CP1
4
OUT1A
28 VBB1
SENSE1 1
27 SLEEPn
HOMEn 2
26 ENABLEn
DIR 3
OUT1A 4
AGND 7
PAD
22 VCP
Description
Logic input
DMOS full-bridge 1, output A
REF 8
21 PGND
5
PFD
Analog input for mixed-decay setting
RC2 9
20 VREG
6
RC1
Analog input for fixed off-time, bridge 1
VDD 10
19 STEP
7
AGND*
8
REF
Gm reference input
Analog input for fixed off-time, bridge 2
OUT2A 11
18 OUT2B
MS2 12
17 RESETn
MS1 13
16 SR
SENSE2 14
15 VBB2
Package LP,
28-Pin TSSOP
Analog ground
9
RC2
10
VDD
11
OUT2A
12
MS2
Logic input
13
MS1
Logic input
14
SENSE2
15
VBB2
Logic supply voltage
DMOS full-bridge 2, output A
Sense resistor for bridge 2
Load supply for bridge 2
16
SR
Logic input
17
RESETn
Logic input
18
OUT2B
DMOS full-bridge 2, output B
19
STEP
Logic input
20
VREG
Regulator decoupling
21
PGND*
Power ground
22
VCP
Reservoir capacitor
23
CP1
Charge pump capacitor
24
CP2
Charge pump capacitor
25
OUT1B
26
ENABLEn
DMOS full-bridge 1, output B
Logic input
27
SLEEPn
Logic input
28
VBB1
Load supply for bridge 1
–
PAD*
Thermal pad
* GND, PGND, and thermal pad must be connected together externally under the device.
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
3
A5977
Microstepping DMOS Driver with Translator
FUNCTIONAL BLOCK DIAGRAM
CP1
VREG
Logic
Supply
VDD
UVLO
Charge
Pump
Regulator
SENSE1
Reference
Supply
REF
CP2
VCP
Load
Supply
VBB1
DAC
÷8
RC1
DMOS
H-BRIDGE
4
STEP
DIR
PWM Timer
PWM Latch
Blanking
Mixed Decay
RESETn
MS1
Translator
OUT1A
OUT1B
SENSE1
MS2
HOMEn
4
SLEEPn
Control
Logic
SR
Gate
Drive
SENSE1
VBB2
ENABLEn
DMOS
H-BRIDGE
RC2
PWM Timer
PWM Latch
Blanking
Mixed Decay
VDD
OUT2A
OUT2B
DAC
SENSE2
PFD
AGND
PGND
Exposed Thermal Pad
(Required)
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
4
A5977
Microstepping DMOS Driver with Translator
ELECTRICAL CHARACTERISTICS1: Valid at TA = 25°C, VBB = 40 V, unless otherwise noted
Characteristics
Symbol
Load Supply Voltage Range
VBB
Output Leakage Current
IDSS
Output On-Resistance
Body Diode Forward Voltage
VBB Supply Current
VDD Supply Current
RDS(On)
VF
IBB
IDD
Test Conditions
Min.
Typ.2
Max.
Units
Operating
8
–
40
V
During sleep mode
0
–
40
V
VOUT = VBB
–
<1
20
µA
VOUT = 0 V
–
<1
–20
µA
Source driver, IOUT = –2.5 A, TJ = 25°C
–
0.22
0.30
Ω
Sink driver, IOUT = 2.5 A, TJ = 25°C
–
0.15
0.24
Ω
Source diode, IF = –2.5 A
–
1
1.4
V
Source diode, IF = 2.5 A
–
1
1.4
V
fPWM < 50 kHz, duty cycle = 50%
–
–
8
mA
Operating, outputs disabled
–
–
6
mA
Sleep mode
–
<1
20
μA
fPWM < 50 kHz, duty cycle = 50%
–
–
12
mA
Operating, outputs disabled
–
–
10
mA
Sleep mode
–
<1
20
μA
V
Control Logic
Logic Supply Voltage Range
Logic Input Voltage
Logic Input Current
Maximum Step
Frequency3
HOMEn Output Voltage
Blank Time
Fixed Off-Time
Reference Input Voltage Range
Reference Input Current
Gain (Gm)
Error4
3
–
5.5
VIN(1)
0.7× VDD
–
–
V
VIN(0)
–
–
0.3 ×VDD
V
VDD
Operating
IIN(1)
VIN = 0.7 × VDD
–20
<1
20
µA
IIN(0)
VIN = 0.3 × VDD
–20
<1
20
µA
500
–
–
kHz
VOH
IOH = –200 µA
0.7× VDD
–
–
V
VOL
IOL = 200 µA
fSTEP
–
–
0.3 ×VDD
V
tBLANK
RT = 56 kΩ, CT = 680 pF
700
950
1200
ns
tOFF
RT = 56 kΩ, CT = 680 pF
30
38
46
μs
Operating
0
–
VDD
V
–
–
±3
μA
VREF = 2 V, phase current = 100.0%
–
–
±5
%
VREF = 2 V, phase current = 70.7%
–
–
±5
%
VREF = 2 V, phase current = 38.3%
–
–
±10
%
100
475
800
ns
20
–
120
ns
VREFx
IREF
EG
Crossover Dead Time
tDT
Motor Output Slew Time
tSR
10% to 90% rising; 90% to 10% falling
Continued on the next page...
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
5
A5977
Microstepping DMOS Driver with Translator
ELECTRICAL CHARACTERISTICS1 (continued): Valid at TA = 25°C, VBB = 40 V, unless otherwise noted
Characteristics
Symbol
Test Conditions
Min.
Typ.2
Max.
Units
2.45
2.7
2.95
V
Protection Circuits
VBB rising
VDD UVLO Threshold
VUV(VBB)
VDD UVLO Hysteresis
VUV(VBB)HYS
50
100
–
mV
IOCPST
3.5
–
–
A
tLATCHOFF(OC)
–
1.6
–
ms
tBLANK(OC)
–
1.5
–
µs
TJSD
155
165
175
°C
TJSDHYS
–
15
–
°C
Overcurrent Protection Threshold
Overcurrent Latch-Off Time
Overcurrent Protection Blank Time
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
1
Typical data are for initial design estimations only, and assume optimum manufacturing and application conditions. Performance may vary for individual units, within
the specified maximum and minimum limits.
2
Negative current is defined as coming out of (sourcing from) the specified device pin.
3
4
Operation at a step frequency greater than the specified minimum value is possible but not warranteed.
EG = ( [ VREF / 8] – VSENSE ) / ( VREF / 8 ).
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
6
A5977
Microstepping DMOS Driver with Translator
tA
tB
STEP
tC
tD
MSx,
RESETn, or DIR
t WU
SLEEPn
Time Duration
Symbol
Typ.
Unit
STEP Minimum, high pulse width
tA
1
µs
STEP Minimum, low pulse width
tB
1
µs
Setup time, input change to STEP
tC
200
ns
Hold time, input change to STEP
tD
200
ns
tWU
1
ms
Maximum wakeup time
Figure 1: Logic Interface Timing Diagram
Table 1: Microstep Resolution Truth Table
MS2
MS1
Microstep Resolution
Excitation Mode
L
L
Full Step
2 Phase
L
H
Half Step
1-2 Phase
H
L
Quarter Step
W1-2 Phase
H
H
Eighth Step
2W1-2 Phase
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
7
A5977
Microstepping DMOS Driver with Translator
FUNCTIONAL DESCRIPTION
Device Operation
The A5977 is a complete microstepping motor driver with builtin translator for easy operation with minimal control lines. It is
designed to operate bipolar stepper motors in full-, half-,
quarter-, and eighth-step modes. The current in each of the two
output full-bridges, all N-channel DMOS, is regulated with fixed
off-time pulse-width modulated (PWM) control circuitry. The
full-bridge current at each step is set by the value of an external
current-sense resistor (RS), a reference voltage (VREF), and the
output voltage of its DAC (which in turn is controlled by the
output of the translator).
At power-up, or reset, the translator sets the DACs and phase
current polarity to the initial home state (see figures for homestate conditions), and sets the current regulator for both phases to
mixed-decay mode. When a step command signal occurs on the
STEP input, the translator automatically sequences the DACs to
the next level (see Table 2 for the current level sequence and current polarity). The microstep resolution is set by inputs MS1 and
MS2 as shown in Table 1. If the new DAC output level is lower
than the previous level, the decay mode for that full-bridge will
be set by the PFD input (fast, slow, or mixed decay). If the new
DAC level is higher or equal to the previous level, then the decay
mode for that full-bridge will be slow decay. This automatic
current-decay selection will improve microstepping performance
by reducing the distortion of the current waveform due to the
motor BEMF.
When stepping, if the new output levels of the DACs are higher
than or equal to their previous levels, then the decay mode for
that full-bridge is set to slow. If the new output levels of the
DACs are lower than their previous output levels, then the decay
mode for that full-bridge is set by the state of the PFD input (see
PFD input description). This automatic current decay selection
improves microstepping performance by reducing the distortion
of the current waveform that results from the back-EMF of the
motor. See Figure 6 on page 14 for decay mode detail.
Internal PWM Current Control
Each full-bridge is controlled by a fixed off-time PWM currentcontrol circuit that limits the load current to an appropriate
level (ITRIP). Initially, a diagonal pair of source and sink DMOS
outputs are enabled, and current flows through the motor wind-
ing and the current-sense resistor, RS. When the voltage across
RS rises to the DAC output voltage, the current-sense comparator
resets the PWM latch, which turns off the source driver (in slowdecay mode) or the sink and source drivers (in fast- or mixeddecay mode).
The maximum level of current limiting is set by the selection of
RS and the voltage at the VREF input with a transconductance
function approximated by:
ITRIPmax = VREF / (8 × RS)
The DAC output reduces the VREF output to the current-sense
comparator in precise steps (see Table 2 for % ITRIPmax at each
step).
ITRIP = (% ITRIPmax / 100) × ITRIPmax
It is critical to ensure that the maximum rating on the SENSE
terminal is not exceeded (0.5 V). For full-step mode, VREF can be
applied up to the maximum rating of VDD, because the peak sense
value is 0.707 × VREF / 8. In all other modes, VREF should not
exceed 4 V.
Fixed Off-Time
The internal PWM current-control circuitry uses a one-shot to
control the time that the drivers remain off. The one-shot offtime, tOFF, is determined by the selection of an external resistor (RT) and capacitor (CT) connected between the RC timing
terminal and ground. The off-time, over a range of values of CT
= 470 pF to 1500 pF and RT = 12 kΩ to 100 kΩ is approximated
by:
tOFF = RT × CT
RC Blanking
In addition to the fixed off-time of the PWM control circuit, the
CT component sets the comparator blanking time. This function blanks the output of the current-sense comparator when the
outputs are switched by the internal current-control circuitry. The
comparator output is blanked to prevent false overcurrent detection due to reverse-recovery currents of the clamp diodes, and/
or switching transients related to the capacitance of the load. The
blank time, tBLANK, can be approximated by:
tBLANK = 1400 × CT
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
8
A5977
Microstepping DMOS Driver with Translator
Step Input (STEP)
Home Output (HOMEn)
A low-to-high transition on the STEP input sequences the translator and advances the motor one increment. The translator controls
the input to the DACs and the direction of current flow in each
winding. The size of the increment is determined by the state of
inputs MS1 and MS2 (see Table 1).
The HOMEn output is a logic output indicator of the initial state
of the translator. At power-up, the translator is reset to the home
state (see figures for home state conditions), and the HOMEn
output will be low. When the translator is not in the home state,
this output is high.
Microstep Select (MS1 and MS2)
Synchronous Rectification
Input terminals MS1 and MS2 select the microstepping format
per Table 1. Changes to these inputs do not take effect until the
STEP command.
When a PWM off-cycle is triggered by an internal current control, load current will recirculate according to the decay mode
selected by the control logic. The A5977 synchronous rectification feature will turn on the appropriate MOSFETs during the
current decay and effectively short out the body diodes with the
low RDS(ON) driver. This will reduce power dissipation significantly and eliminate the need for external Schottky diodes for
most applications.
Direction Input (DIR)
The state of the DIR input will determine the direction of rotation
of the motor.
Percent Fast-Decay Input (PFD)
When a STEP input command results in a lower output current
than the previous step, it switches the output current decay for
that bridge to either slow-, fast-, or mixed-decay, depending on
the voltage level at the PFD input. If the voltage at the PFD input
is greater than 0.6 × VDD, then slow-decay is selected. If the
voltage on the PFD input is less than 0.21 × VDD, then fast-decay
is selected. Mixed-decay is selected when the voltage on the
PFD input is between these two levels. This terminal should be
decoupled with a 0.1 µF capacitor.
Mixed-Decay Operation
If the voltage on the PFD input is between 0.6 × VDD and 0.21 ×
VDD, the bridge will operate in mixed-decay mode when a STEP
input command results in a lower output current that the previous
step. As the trip point is reached, the bridge will go into fastdecay mode until the voltage on the RC terminal decays to the
voltage applied to the PFD terminal. The time the bridge remains
in fast-decay is approximated by:
tFD = RT × CT × In (0.6 × VDD / VPFD)
After this fast-decay portion, tFD, the bridge will switch to slowdecay mode for the remainder of the fixed off-time period.
Reset Input (RESETn)
The RESETn input (active low) sets the translator to a predefined
home state (see figures for home state conditions) and turns off
all of the DMOS outputs. The HOMEn output goes low and all
STEP inputs are ignored until the RESETn input goes high.
The synchronous rectification can be set in either active mode or
disabled mode using the SR pin.
Synchronous Rectification Mode (SR)
When the SR input is logic-low, active mode is enabled and synchronous rectification will occur. Reversal of the current in the
motor winding is prevented when using this mode by turning off
synchronous rectification if the current in the winding decays to
zero. When the SR input is logic-high, synchronous rectification
is disabled. Synchronous rectification is typically disabled only
when external diodes are required to transfer power dissipation
from the A5977 package to the external diodes.
Enable Input (ENABLEn)
This active-low input enables all of the DMOS outputs. When
logic-high, the outputs are disabled. Inputs to the translator (STEP, DIR, MS1, MS2) are all active independent of the
ENABLEn input state.
Sleep Mode (SLEEPn)
This active-low input is used to minimize power consumption
when the device is not in use. Sleep mode disables much of the
internal circuitry, including the output DMOS, regulator, and
charge pump. A logic-high allows normal operation and a rising
edge on this input resets the translator to the home position.
When coming out of sleep mode, 1 ms is required before issuing
a STEP command, to allow the charge pump to stabilize.
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
9
A5977
Microstepping DMOS Driver with Translator
Charge Pump (CP1 and CP2)
The charge pump is used to generate a gate supply greater than
VBB to drive the source-side DMOS gates. A 0.22 µF ceramic
capacitor is required between CP1 and CP2, and a 0.22 µF
ceramic capacitor is required between VCP and VBB. VCP is
internally monitored, and in the case of a fault condition, the
outputs of the device are disabled.
VREG
This internally generated voltage is used to operate the sink-side
DMOS gates. The VREG terminal should be decoupled with
a 0.22 µF capacitor to ground. VREG is internally monitored,
and in the case of a fault condition, the outputs of the device are
disabled.
Shutdown
In the event of a fault (excessive junction temperature, or low
voltage on VCP or VREG), the outputs of the device are disabled until the fault condition is removed. At power-up, and in
the event of low VDD, the undervoltage lockout (UVLO) circuit
disables the drivers and resets the translator to the home position.
Overcurrent Protection (OCP)
If any FET’s current exceeds IOCP for longer than the blank time,
all FETs are disabled for 1.6 ms. RSENSE is not required for lowside OCP to function and the OCP threshold is independent of the
RSENSE value.
10
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
A5977
Microstepping DMOS Driver with Translator
PHASE CURRENT DIAGRAMS
IOUT2(A→B)
2
70%
1
IOUT1(A→B)
70%
4
3
Figure 2: Full Step
MS2 = L, MS1 = L, DIR = H. See Table 2 for step number detail.
IOUT2(A→B)
3
4
70%
2
5
70%
1
IOUT1(A→B)
8
6
7
Figure 3: Half Step
MS2 = L, MS1 = H, DIR = H. See Table 2 for step number detail.
11
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
A5977
Microstepping DMOS Driver with Translator
IOUT2(A→B)
5
70%
7
3
9
1
70%
IOUT1(A→B)
15
11
13
Figure 4: Quarter Step
MS2 = H, MS1 = L, DIR = H. See Table 2 for step number detail.
IOUT2(A→B)
9
13
70%
5
17
70%
1
IOUT1(A→B)
29
21
25
Figure 5: Eighth Step
MS2 = H, MS1 = H, DIR = H. See Table 2 for step number detail.
12
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
A5977
Microstepping DMOS Driver with Translator
Table 2: Step Sequencing Settings
DIR = H; 360° = 4 full steps; home microstep position at step angle 45º
Full
Step
#
Half
Step
#
1
1/4
Step
#
1
2
1*
2*
3*
4
3
5
6
2
4
7
8
5
9
10
3
6
11
12
7
13
14
4
8
15
16
Phase 1
Current
Phase 2
Current
[% ItripMax]
[% ItripMax]
(%)
0.0
Step
Angle
(º)
0.0
2
98.1
19.5
11.3
3
92.4
38.3
22.5
4
83.1
55.6
33.8
5*
70.7*
70.7*
45.0*
6
55.6
83.1
56.3
7
38.3
92.4
67.5
8
19.5
98.1
78.8
9
0.0
100.0
90.0
10
-19.5
98.1
101.3
11
-38.3
92.4
112.5
12
-55.6
83.1
123.8
1/8
Step
#
1
(%)
100.0
13
-70.7
70.7
135.0
14
-83.1
55.6
146.3
15
-92.4
38.3
157.5
16
-98.1
19.5
168.8
17
-100.0
0.0
180.0
18
-98.1
-19.5
191.3
19
-92.4
-38.3
202.5
20
-83.1
-55.6
213.8
21
-70.7
-70.7
225.0
22
-55.6
-83.1
236.3
23
-38.3
-92.4
247.5
24
-19.5
-98.1
258.8
25
0.0
-100.0
270.0
26
19.5
-98.1
281.3
27
38.3
-92.4
292.5
28
55.6
-83.1
303.8
29
70.7
-70.7
315.0
30
83.1
-55.6
326.3
31
92.4
-38.3
337.5
32
98.1
-19.5
348.8
* Home state; HOMEn output low.
13
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
A5977
Microstepping DMOS Driver with Translator
Slow
Decay
Current Decay
Mode
Full-Step
Winding Current
0A
Current Decay
Mode
Slow
Decay
Set
by
PFD
Input
Slow
Decay
Set
by
PFD
Input
Slow
Decay
Set
by
PFD
Input
Slow
Decay
Half-Step
Winding Current
0A
Current Decay
Mode
Slow
Decay
Set by
PFD
Input
Slow
Decay
Set by
PFD
Input
Slow
Decay
Set by
PFD
Input
Slow
Decay
Quarter-Step
Winding Current
0A
Figure 6: Automatic Decay Mode
14
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
A5977
Microstepping DMOS Driver with Translator
PACKAGE OUTLINE DRAWING
0.45
9.70 ±0.10
28
+0.05
0.15 –0.06
0.65
28
4° ±4
1.65
B
3.00
4.40 ±0.10
6.40 ±0.20
A
1
6.10
(1.00)
2
5.00
0.25
28X
SEATING
PLANE
0.10 C
+0.05
0.25 –0.06
3.00
0.60 ±0.15
0.65
C
SEATING PLANE
GAUGE PLANE
1 2
5.00
C
PCB Layout Reference View
1.20 MAX
0.10 MAX
For reference only
(reference JEDEC MO-153 AET)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A Terminal #1 mark area
B Exposed thermal pad (bottom surface)
C Reference land pattern layout (reference IPC7351 SOP65P640X120-29CM);
All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary
to meet application process requirements and PCB layout tolerances; when
mounting on a multilayer PCB, thermal vias at the exposed thermal pad land
can improve thermal dissipation (reference EIA/JEDEC Standard JESD51-5)
Figure 7: LP Package, 28-Pin TSSOP with Exposed Thermal Pad
15
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
A5977
Microstepping DMOS Driver with Translator
Revision History
Revision
Current
Revision Date
–
December 21, 2015
1
January 21, 2016
2
May 31, 2016
Description of Revision
Initial release
Corrected formula on page 8
Corrected setup and hold time units on page 7
Copyright ©2016, Allegro MicroSystems, LLC
Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to
permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that
the information being relied upon is current.
Allegro’s products are not to be used in any devices or systems, including but not limited to life support devices or systems, in which a failure of
Allegro’s product can reasonably be expected to cause bodily harm.
The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its
use; nor for any infringement of patents or other rights of third parties which may result from its use.
For the latest version of this document, visit our website:
www.allegromicro.com
16
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com