ECL Datasheet

ECL
www.vishay.com
Vishay Roederstein
Aluminum Capacitors
FEATURES
• Load life: 2000 h at 105 °C
• Extra low impedance, high ripple current
• Polarized SMD aluminum electrolytic capacitors,
non solid electrolyte
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
QUICK REFERENCE DATA
DESCRIPTION
APPLICATIONS
VALUE
Nominal case size
(Ø D x L in mm )
• SMD technology, for high mounting density
• Industrial and professional applications
6 x 5.8 to 12.5 x 13.5
Rated capacitance range CR
Capacitance tolerance
• General industrial, consumer
10 μF to 1500 μF
• Smoothing, filtering, buffering
± 20 %
Rated voltage range
6.3 V to 50 V
Category temperature range
Load life
PACKAGING
- 40 °C to 105 °C
Supplied in blister tape.
2000 h
Based on sectional
specification
IEC 60384-4/EN 130300
Climatic category
IEC 60068
40/105/56
SELECTION CHART FOR CR, UR, AND RELEVANT NOMINAL CASE SIZES (Ø D x L in mm)
CR
(μF)
RATED VOLTAGE (V)
6.3
10
16
25
35
50
10





6.3 x 5.8
22





6.3 x 5.8
33




6.3 x 5.8
8 x 6.2
47




6.3 x 5.8
8 x 6.2
68



6.3 x 5.8
8 x 6.2
8 x 10
100


6.3 x 5.8
8 x 6.2
8 x 10
10 x 10
220
6.3 x 5.8
6.3 x 7.7
8 x 6.2
8 x 10
10 x 10
-
330
8 x 6.2

8 x 10
-
-
-
470

8 x 10
10 x 10
-
-
-
680

10 x 10
-
-
-
-
1000
10 x 10
-
-
-
-
-
1500
10 x 10
-
-
-
-
-
Revision: 18-Oct-12
Document Number: 25020
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ECL
www.vishay.com
Vishay Roederstein
DIMENSIONS in millimeters
CASE SIZE
CODE
D±
L±
A±
B±
C±
E±
R
N
P
0.5
AD
6.3 ± 0.5
5.8 ± 0.3
2.4 ± 0.2
6.6 ± 0.2
6.6 ± 0.2
2.2 ± 0.2
0.5 to 0.8
0.3
BM
6.3 ± 0.5
7.7 ± 0.4
2.4 ± 0.2
6.6 ± 0.2
6.6 ± 0.2
2.2 ± 0.2
0.5 to 0.8
0.3
0.5
AE
8 ± 0.5
6.2 ± 0.4
3.3 ± 0.2
8.3 ± 0.2
8.3 ± 0.2
2.3 ± 0.2
0.5 to 0.8
0.3
0.5
AF
8 ± 0.5
10 ± 0.5
2.9 ± 0.2
8.3 ± 0.2
8.3 ± 0.2
3.1 ± 0.2
0.8 to 1.1
0.3
0.5
AG
10 ± 0.5
10 ± 0.5
3.2 ± 0.2
10.3 ± 0.2
10.3 ± 0.2
4.5 ± 0.2
0.8 to 1.1
0.3
0.5
AH
12.5 ± 0.5
13.5 ± 0.5
4.6 ± 0.2
12.8 ± 0.2
12.8 ± 0.2
4.5 ± 0.2
1.1 to 1.4
0.3
0.5
Capacitance
N max.
Plastic plateform
C±α
+ Positive
P max.
A±α
E±α
A±α
Voltage
B±α
Lot no.
ØD±α
22 A
50
+
L±α
- Negative
ORDERING EXAMPLE
ELECTRICAL DATA
SYMBOL
R
ECL 22 μF/50 V, ± 20 %, size 6.3 x 5.8 mm
DESCRIPTION
Ordering code: MALSECL00AD222HARK
UR
Rated voltage
CR
Rated capacitance at 120 Hz
tan 
Max. dissipation factor at 120 Hz
RESR
Max. equivalent series resistance at 120 Hz
IR
Rated alternating current at 120 Hz and upper
catagory temperature
Z
Max. impedance at 100 kHz
For Standard Packaging Quantity (SPQ) and Minimum Order
Quantity (MOQ) please refer to our price list or contact
customer service.
Note
• Unless otherwise specified, all electrical values apply at
Tamb = 20 °C, P = 86 to 100 kPa, RH = 45 to 75 %.
ELECTRICAL DATA AND ORDERING INFORMATION
UR
(V)
6.3
10
16
Z
100 kHz/
20 °C
()
CR
120 Hz
(μF)
DIMENSIONS
DxL
(mm)
220
6.3 x 5.8
0.24
0.44
330
8 x 6.2
0.24
0.26
1000
10 x 10
0.24
0.09
1500
10 x 10
0.24
220
6.3 x 7.7
0.19
tan 
120 Hz
IR
100 kHz/
105 °C
(mA)
WEIGHT
(g)
CATALOG NUMBER
230
0.30
MALSECL00AD322BARK
300
0.55
MALSECL00AE333BARK
670
1.21
MALSECL00AG410BARK
0.09
670
1.21
MALSECL00AG415BARK
0.34
280
0.40
MALSECL00BM322CARK
470
8 x 10
0.19
0.17
450
1.00
MALSECL00AF347CARK
680
10 x 10
0.19
0.09
670
1.21
MALSECL00AG368CARK
100
6.3 x 5.8
0.16
0.44
230
0.30
MALSECL00AD310DARK
220
8 x 6.2
0.16
0.26
300
0.55
MALSECL00AE322DARK
330
8 x 10
0.16
0.17
450
1.00
MALSECL00AF333DARK
470
10 x 10
0.16
0.09
670
1.21
MALSECL00AG347DARK
Revision: 18-Oct-12
Document Number: 25020
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ECL
www.vishay.com
Vishay Roederstein
ELECTRICAL DATA AND ORDERING INFORMATION
UR
(V)
25
35
50
CR
120 Hz
(μF)
DIMENSIONS
DxL
(mm)
tan 
120 Hz
Z
100 kHz/
20 °C
()
IR
100 kHz/
105 °C
(mA)
WEIGHT
(g)
CATALOG NUMBER
68
100
220
33
47
68
100
220
10
22
33
47
68
100
6.3 x 5.8
8 x 6.2
8 x 10
6.3 x 5.8
6.3 x 5.8
8 x 6.2
8 x 10
10 x 10
6.3 x 5.8
6.3 x 5.8
8 x 6.2
8 x 6.2
8 x 10
10 x 10
0.14
0.14
0.14
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.44
0.26
0.17
0.44
0.44
0.26
0.17
0.09
0.88
0.88
0.63
0.63
0.34
0.18
230
300
450
230
230
300
450
670
165
165
300
300
450
670
0.30
0.55
1.00
0.30
0.30
0.55
1.00
1.21
0.30
0.30
0.55
0.55
1.00
1.21
MALSECL00AD268EARK
MALSECL00AE310EARK
MALSECL00AF322EARK
MALSECL00AD233FARK
MALSECL00AD247FARK
MALSECL00AE268FARK
MALSECL00AF310FARK
MALSECL00AG322FARK
MALSECL00AD210HARK
MALSECL00AD222HARK
MALSECL00AE233HARK
MALSECL00AE247HARK
MALSECL00AF268HARK
MALSECL00AG310HARK
REFLOW SOLDERING CONDITIONS FOR SMD ALUMINUM ELECTROLYTIC CAPACITORS
tP
TP
Critical Zone
TL to TP
Temperature
Ramp-up
TL
tL
Ts max.
Ts min.
Ramp-down
ts
Preheat
t 25 °C to Peak
Time
PROFILE FEATURE
Average ramp-up rate (TL to TP)
Preheat
Temperature min. (Ts min.)
Temperature max. (Ts max.)
Time (Ts min. to Ts max.)
Ts max. to TL
Ramp-up rate
Time maintained above
Temperature (TL)
Time (tL)
Peak/classification temperature (TP)
Time within 5 °C of actual peak temperature (TP)
Ramp-down rate
Time 25 °C to peak temperature
Revision: 18-Oct-12
Ø 4 TO Ø 10
3 °C/s max.
150 °C
200 °C
60 s to 150 s
SOLDERING CONDITION
Ø 12.5
3 °C/s max.
Ø 16
150 °C
200 °C
40 s to 120 s
40 s to 100 s
3 °C/s max.
3 °C/s max.
217 °C
60 s to 90 s
250 °C
10 s max.
3 °C/s max.
8 min max.
217 °C
40 s to 60 s
240 °C
230 °C
10 s max.
3 °C/s max.
8 min max.
Document Number: 25020
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ECL
www.vishay.com
Vishay Roederstein
RESISTANCE TO SOLDERING HEAT
Leakage current
Less than specified value
Capacitance value
Within ± 10 % of initial value
tan 
Less than specified value
LOW TEMPERATURE BEHAVIOR (at 120 Hz)
IMPEDANCE RATIO
(Z) T2/(Z) T1
RATED VOLTAGE (V)
T2/T1
6.3
10
16
25
35
50
63
100
- 25 °C/+ 20 °C
2
2
2
2
2
2
3
3
- 40 °C/+ 20 °C
3
3
3
3
3
3
4
4
MULTIPLIER OF RIPPLE CURRENT (IR) AS A FUNCTION OF FREQUENCY
FREQUENCY (Hz)
IR MULTIPLIER
50
0.41
120
0.59
300
0.69
1000
0.80
10 000
0.88
100 000
1.00
ADDITIONAL ELECTRICAL DATA
PARAMETER
CONDITIONS
VALUE
Current
Leakage current
(test conditions: UR, 20 °C)
After 2 min at UR
IL2  0.01 x CR x UR
or 3 μA
for UR  100 V (whichever is greater)
Resistance
Equivalent series resistance
(ESR)
Calculated from tan max.
ESR = tan /2  f CR
TEST PROCEDURES AND REQUIREMENTS
TEST
PROCEDURE
(quick reference)
REQUIREMENTS
Load life
Tamb = 105 °C
UR and IR applied
After 2000 h
C/C: ± 25 % of initial value
IL  spec. limit
tan   2 x spec. limit
Shelf life
No voltage applied
After 1000 h
After test: UR to be applied for 30 min
24 h to 48 h before measurement
C/C: ± 25 % of initial value
IL  spec. limit
tan   2 x spec. limit
Revision: 18-Oct-12
Document Number: 25020
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000