Download

CH-517RXHS
HDMI Scaler over CAT5e/6/7 Receiver with LAN/
RS-232/IR/Bidirectional PoE
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology. All Rights Reserved.
Version 1.0 September 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•
Never spill liquid of any kind on or into this product.
•
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
•
Do not attach the power supply cabling to building surfaces.
•
Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
•
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
•
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO.
DATE DD/MM/YY SUMMARY OF CHANGE
VR0
01/11/13
Preliminary release
VS1
09/10/13
Updated text/diagrams
CONTENTS
1. Introduction�������������������������������������������� 1
2. Applications������������������������������������������� 1
3. Package Contents�������������������������������� 1
4. System Requirements���������������������������� 1
5. Features�������������������������������������������������� 2
6. Operation Controls and Functions������� 3
6.1 Front Panel�����������������������������������������3
6.2 Rear Panel�����������������������������������������4
6.3 Remote Control���������������������������������5
6.4 IR Cable Pin Assignment������������������5
6.5 RS-232 Pin Definitions������������������������6
6.6 RS-232 Commands���������������������������7
6.7 OSD Menu������������������������������������������9
6.8 Output Resolutions Support�����������11
7. Connection Diagram�������������������������� 12
8. Specifications�������������������������������������� 13
8.1 Technical Specifications����������������13
8.2 CAT5e/6/7 Cable Specification����14
9. Acronyms��������������������������������������������� 14
1. INTRODUCTION
The CH-517RXHS is an HDBaseT™ Receiver Scaler designed to scale
the incoming video signal first, before outputting to its HDMI port.
There is an Optical port providing additional audio extraction feature.
Besides video and audio from the Transmitter, it also takes in 2-way IR,
RS-232 and bidirectional LAN serving, over a single run of CAT5e/6/7
cable at a distance up to 100 meters. Control is via on-panel buttons
or IR remote control and there is an On-screen Display (OSD) providing
selection and system information. The device provides a full range
of output resolutions, up to 1080p and WUXGA (RB). The bidirectional
Power over Ethernet (PoE) function provides greater flexibility in
installations.
2. APPLICATIONS
• Up-scale HDMI output to HDTV/PC resolutions
• Up-scale standard definition video to High-Definition TVs/displays
• Extend the operating distance of an HDMI signal
• Lecture room/Showroom/Meeting room/Classroom display and control
3. PACKAGE CONTENTS
• CAT5e/6/7 to HDMI with LAN/IR/RS-232/Bidirectional PoE Receiver
• 1×IR Receiver
• 1×IR Blaster
• 24 V/2.7 A DC Power Adaptor
• Remote Control (CR-128)
• Operation Manual
4. SYSTEM REQUIREMENTS
HDBaseT compatible Transmitter (input) and output to display with an
HDMI input connection.
1
5. FEATURES
• Supports HDMI scaling to a wide range of HDTV or PC resolutions up
to 1080p and WUXGA (RB)
• Reception of uncompressed data over a single CAT5e/6/7 cable up
to 100m/328ft
• HDBaseT™ 5Play convergence: uncompressed high definition Video
and Audio, LAN serving, Bidirectional Power over Ethernet (PoE) and
controls (IR & RS-232 bypass)
• Supports IR, Remote control, RS-232 (bypass) and on-panel controls
• Provides bidirectional 24V DC power to or receive from compatible
PoE Transmitter through CAT5e/6/7 cable
• Supports Ethernet transmission rates up to 100 Mbps
• Supports HDMI, Optical (S/PDIF) audio sampling rates up to 48kHz
• Supports HDMI and Optical (S/PDIF) audio up to LPCM 2CH
Note:
1. This system was tested with CAT6/23AWG cables, results may vary
with cables of a different specification.
2. The PoE function is designed for powering compatible Transmitter
units only—non-PoE Transmitters will need their own power supply.
Transmitters from other brands may not be compatible.
3. DO NOT connect the LAN connection to the CAT5e/6/7 port.
Doing so may cause a power shutdown and may damage the
device.
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
OPTICAL OUT
SERVICE
HDMI OUT
XGA
MENU
-
+
ENTER
720P
1
2
3
4
5
6
7
1 SERVICE: Reserved for manufacturer use only.
2 IR RECEIVER WINDOW: Receives only the IR signal from the supplied
remote control.
3 OPTICAL OUT: Connect to an amplifier or active speakers with an
optical cable.
4 HDMI OUT: Connect to an HDMI TV/Monitor
5 MENU: Press this button to enter the On-Screen Display (OSD)
menu.
6 −/+: Use these buttons to navigate down and up in the on-screen
menu.
7 ENTER: Press this button to confirm the selection.
Note:
Pressing '−' (MINUS) and ENTER simultaneously will immediately
switch the output resolution of the device to 720p60.
Pressing '+' (PLUS) and ENTER simultaneously will immediately switch
the output resolution of the device to XGA (1024×768).
3
6.2 Rear Panel
DC 24V
RS232 OUT
LAN
IR
Blaster
IR
Extender
CAT5e/6 IN
POWER
MODE
1
2
3
4
5
6
LINK
7
1 POWER LED: This LED will illuminate when the device is connected
to an active power supply.
2 DC 24V: Connect the 24 V DC power supply to the unit and plug
the adaptor into an AC outlet. Only one unit requires powering if
both the Transmitter and Receiver are both PoE compatible.
3 RS-232 OUT: Connect to the device that is to be controlled (via
D-Sub 9 pin female cable) by RS-232 commands.
4 LAN: Connect to an active network for LAN serving. When any
compatible LAN equipped receivers are connected, this allows
the network access (including internet access if available) to
be shared between any connected LAN equipped receivers.
Connect any Ethernet equipped device e.g. a Smart TV or games
console to the LAN port of a receiver for that device to share the
network/internet access.
Warning: DO NOT connect the LAN connection to the CAT5e/6/7
port. Doing so may cause a power shutdown and may damage the
device.
5 IR Blaster: Connect the supplied IR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
6 IR Extender: Connect to the supplied IR Receiver cables for IR
signal reception. Ensure that remote being used is within the direct
line-of-sight of the IR Extender.
7 CAT5e/6/7 IN: Connect to the Transmitter unit with a Single
CAT5e/6 cable for receiving all data signals.
MODE LED: This LED will illuminate when the power is connected.
LINK LED: This LED will illuminate when connected to a Transmitter
unit that is connected to a source that is outputting a signal.
4
6.3 Remote Control
1 INPUT: Not functional.
2 EXIT: Press this button to exit the menu
or escape the current selection under
OSD.
3 MENU: Press this button to exit the menu
1
or the current selection in the on-screen 2
menu.
4 RESET: Press this button to return the
device to the factory default settings.
5 AUTO ADJUST: Not functional.
6 OK & ▲▼◄►: Press 'OK' to confirm the
INPUT
EXIT
MENU
OK
5
4
RESET
AUTO
ADJUST
6
selection or use the directional buttons
to navigate the on-screen menus.
CR-128
6.4 IR Cable Pin Assignment
IR Blaster
1 Power
2 IR Blaster Signal
3 NC
IR Extender
1 IR Signal
2 Power
3 Ground
5
3
6.5 RS-232 Pin Definitions
PIN
DEFINE TX / RX
1
N/C
2
TxD/RxD
3
RxD/TxD
4
NC
5
GND
6
NC
7
NC
8
NC
9
NC
Baud Rate: 9600bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
6
6.6 RS-232 Commands
COMMAND
DESCRIPTION
S OUTPUT 0~25
0=Native
12=1600×1200
1=640×480
13=1920×1080
2=800×600
16=1920×1200
3=1024×768
17=480p
5=1360×768
[email protected]
6=1280×720
[email protected]
7=1280×800
[email protected]
8=1280×1024
22=576p
9=1440×900
[email protected]
10=1400×1050
[email protected]
11=1680×1050
[email protected]
R OUTPUT
Reports the numerical equivalent for the
OUTPUT setting (as listed above)
S SIZE 0~6
0=OVERSCAN
4=LETTER BOX
1=FULL
5=UNDER 2
2=BEST FIT
6=UNDER 1
3=PAN SCAN
R SIZE
Reports the numerical equivalent for the SIZE
setting (as listed above)
S CONTRAST 0~60
Sets the numerical value for the CONTRAST
setting (0-60)
R CONTRAST
Reports the numerical value for the CONTRAST
setting (0-60)
S BRIGHTNESS 0~60
Sets the numerical value for the BRIGHTNESS
setting (0~60)
R BRIGHTNESS
Reports the numerical value for the BRIGHTNESS
setting (0~60)
S HUE 0~60
Sets the numerical value for the setting (0~60)
R HUE
Reports the numerical value for the setting
(0~60)
7
COMMAND
DESCRIPTION
S SATURATION 0~60
Sets the numerical value for the SATURATION
setting (0~60)
R SATURATION
Reports the numerical value for the SATURATION
setting (0~60)
S SHARPNESS 0~30
Sets the numerical value for the SHARPNESS
setting (0~30)
R SHARPNESS
Reports the numerical value for the SHARPNESS
setting (0~30)
S NR 0~3
0=OFF
2=MIDDLE
1=LOW
3=HIGH
R NR
Reports the numerical equivalent for the NOISE
REDUCTION setting (as listed above)
S AUDIO DELAY 0~3
0=OFF
2=110ms
1=40ms
3=150ms
R AUDIO DELAY
Reports the numeric equivalent for AUDIO
DELAY setting (as listed above)
S AUDIO MUTE 0/1
0=ON
R AUDIO MUTE
Reports the numeric equivalent for AUDIO MUTE
setting (as listed above)
S KEY LOCK 0/1
0=ENABLE
R KEY LOCK
Reports the numeric equivalent for KEY LOCK
setting (as listed above)
FW
Checks the FIRMWARE version
S RESET 1
Sets the numerical equivalent for the RESET
setting (as left)
1=MUTE
1=DISABLE
Note:
1. RS-232 commands will not execute unless followed with carriage
return and LF (Line Feed).
2. Commands are not case-sensitive.
3. Resolutions 1~16 are RGB encoded and 17~25 are YUV encoded.
4. Digital audio supports LPCM 2CH only, please ensure the source
input audio is set to send LPCM 2CH audio in order to avoid
unwanted audio noise.
8
6.7 OSD Menu
1ST LAYER
2ND LAYER
3RD LAYER
DISPLAY
OUTPUT
Native
640x480 60
800x600 60
1024x768 60
1360x768 60
1280x720 60
1280x800 60
1280x1024 60
1440x900 60
1400x1050 60
1680x1050 60
1600x1200 60
1920x1080 60
1920x1200 60
720x480P 60
1280x720P 60
1920x1080I 60
1920x1080P 60
720x576P 50
1280x720P 50
1920x1080I 50
1920x1080P 50
9
1ST LAYER
2ND LAYER
3RD LAYER
SIZE
SIZE
OVER SCAN
FULL
ASPECT RATIO
PAN SCAN
LETTER BOX
UNDER 2
UNDER 1
MODE INFO
INFO
ON
OFF
COLOR
R
G
B
R OFFSET
G OFFSET
B OFFSET
CONTRAST
0~60
BRIGHTNESS
0~60
HUE
0~60
SATURATION
0~60
SHARPNESS
0~60
NR
OFF
LOW
MIDDLE
HIGH
AUDIO
VOLUME
0~100
DELAY
OFF
40mS
110mS
150mS
10
1ST LAYER
2ND LAYER
3RD LAYER
SOUND
ON
MUTE
SETUP
NO
FACTORY RESET
YES
KEY LOCK
OFF
ON
INFORMATION
INPUT
OUTPUT
REVISION
Note: Items in Bold are the default setting.
6.8 Input Resolutions Support
INPUT RESOLUTION
480i/576i
480p/576p
[email protected]/60 Hz
[email protected]/60 Hz
[email protected]/60 Hz
[email protected]/72/75 Hz
[email protected]/60/72/75 Hz
[email protected]/70/75 Hz
[email protected]/75 Hz
[email protected] Hz
1280×[email protected] Hz
1680×[email protected] Hz (RB)
1920×[email protected] Hz
11
HDMI













7. CONNECTION DIAGRAM
DVD Player
RS-232 Control System
HDMI
Input
1.5m
3m
m
7m
m
RS-232
LAN
60°
3m
m
60°
Router with Internet
Connection
IR Blaster
RS-232 In
HDMI In
IR Extender
RS-232 Device to
be Controlled
LAN
Transmitter
HDMI to CAT5e/6 with LAN/IR/RS232
Compatible PoE
Transmitter Unit
CAT5e/6/7
Cable (100m)
RS-232
IR Extender
IR Blaster
Power Supply
DC 24V
RS232 OUT
LAN
IR
Blaster
IR
Extender
CAT5e/6 IN
POWER
MODE
SERVICE
OPTICAL OUT
LINK
HDMI OUT
XGA
MENU
-
+
ENTER
720P
LAN
Digital Audio
Output (Optical)
HDMI
Output
60°
1.5m
60°
AV Receiver
Smart TV
12
8. SPECIFICATIONS
8.1 Technical Specifications
Ethernet Speed
100 Mbps
Input Video Bandwidth
300MHz / 10.2Gbps
Output Video Bandwidth
165MHz / 1.65Gbps
Input Ports
1×CAT5e/6/7, 1×IR Extender
Output Ports
1×HDMI, 1×IR Blaster, 1×Optical,
1×RS-232, 1×LAN
CAT5e/6/7 Output Cable
Up to 100 Meters
Distance
HDMI Resolutions Support
HD: Up to [email protected] Hz
PC: Up to WUXGA (RB)
Audio Sampling Rate
Up to 48 kHz or LCPM 2CH
CAT5e/6/7 Resolutions
HD: Up to [email protected] Hz
Support
PC: Up to WUXGA (RB)
IR Frequency
30~50 kHz
ESD Protection
Human body model:
±8kV (air-gap discharge)
±4kV (contact discharge)
Dimensions
145 mm (W)×192 mm (D)×30 mm (H)/
Jacks Excluded
145 mm (W)×202.75 mm (D)×30
mm(H)/Jacks Included
Weight
608 g
Chassis Material
Aluminum
Color
Black
Operating Temperature
0 ˚C~40 ˚C / 32 ˚F~104 ˚F
Storage Temperature
−20 ˚C ~ 60 ˚C / −4 ˚F ~ 140 ˚F
Relative Humidity
20 ~ 90 % RH (non-condensing)
Power Consumption
14 W
13
8.2 CAT5e/6/7 Cable Specification
Cable Type Range
Pixel Clock Video Data
Rate
Rate
Supported Video
CAT5e/6/7
≤225 MHz
≤5.3 Gbps
Up to 1080p, 60 Hz,
(HD Video)
36 bits, 3D (data
100 m
rates lower than 5.3
Gbps or below 225
MHz TMDS clock).
9. ACRONYMS
ACRONYM
COMPLETE TERM
CAT5e
Category 5 Cable
CAT6
Category 6 Cable
CAT7
Category 7 Cable
HDMI
High-Definition Multimedia Interface
IR
Infrared
WUXGA (RB)
Widescreen Ultra Extended Graphics Array (Reduce
blanking)
14
CYPRESS TECHNOLOGY CO., LTD
Home page: http://www.cypress.com.tw
20130624 MPM-CH517RXHS
Similar pages