Conductive Polymer Aluminum Electrolytic Capacitors (SP-Cap)[pdf :609.88 KB]

2016
Products Catalog
Conductive Polymer Aluminum Electrolytic Capacitors
2016.01
http://industrial.panasonic.com/ww/products/capacitors/polymer-capacitors/sp-cap
——— Notices ———
■ Applicable Laws and Regulations
● This product complies with the RoHS Directive (Restriction of the use of certain Hazardous substances in
electrical and electronic equipment (DIRECTIVE 2011/65/EU).
● No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in
producing this product.
● We do not PBBs or PBDEs as brominated flame retardants.
● Export procedure which followed export related regulations, such as foreign exchange and a foreign trade
method, on the occasion of export of this product Thank you for your consideration.
■ Limited applications
● This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home
appliances, computers and other office equipment, optical equipment, measuring equipment.
● High reliability and safety are required [ be / a possibility that incorrect operation of this product may do harm
to a human life or property ] more. When use is considered by the use, the delivery specifications which suited
the use separately need to be exchanged.
——— Items to be observed ———
● This specification guarantees the quality and performance of the product as individual components.
Before use, check and evaluate their compatibility with installed in your products.
● Do not use the products beyond the specifications described in this document.
■ For specifications
● Install the following systems for a failsafe design to ensure safety if these products are to be used in
equipment where a defect in these products may cause the loss of human life or other signification damage,
such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment,
electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime
prevention equipment.
· The system is equipped with a protection circuit and protection device.
· The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event of
a single fault.
■ Conditions of use
● Before using the products, carefully check the effects on their quality and performance, and determined
whether or not they can be used. These products are designed and manufactured for general-purpose and
standard use in general electronic equipment. These products are not intended for use in the following special
conditions.
(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent.
(2) In direct sunlight, outdoors, or in dust.
(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a
high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NOx.
(4) In an environment where strong static electricity or electromagnetic waves exist.
(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near
these products.
(6) Sealing or coating of these products or a printed circuit board on which these products are mounted,
with resin and other material.
(7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular,
when using water or a water-soluble cleaning agent, be careful not to leave water residues)
(8) Using in the atmosphere which strays Acid or alkaline.
(9) Using in the atmosphere which there are excessive vibration and shock.
● Please arrange circuit design for preventing impulse or transitional voltage.
Do not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage,
instantaneous high voltage, high pulse voltage etc.
● Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid
deterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and
affects performance, characteristics, and functions of customer system.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Application Guidelines (SP-Cap)
1. Circuit design
1.1 Prohibited circuits for use
Do
(1)
(2)
(3)
(4)
(5)
not use the SP-Cap with the following circuit.
Time-constant circuit
Coupling circuits
2 or more SP-Cap connected serially
Circuit which are greatly affected by leakage current
High-impedance voltage retention circuits
1.2 Voltage and polarity
The application of over- voltage and reverse voltage described below can cause increases in leakage current
and short circuits.
Applied voltage, refers to the voltage value including the peak value of the transitional Instantaneous voltage
and the peak value of ripple voltage, not just steady line voltage.
Design your circuit so than the peak voltage does not exceed the stipulated voltage.
[Over-Voltage]
Do not apply over-voltage in excess of the rated voltage. Do not apply voltage, which exceeds the full rated
voltage when the SP-Cap receive impulse voltage, instantaneous high voltage, high pulse voltage etc.
[Reverse-Voltage]
Do not apply reverse-voltage
1.3 Ripple current
Use the SP-Cap within the stipulated permitted ripple current.
When excessive ripple current is applied to the SP-Cap, if causes increases in leakage current and short
circuits due to self-heating.
Even when using the SP-Cap under the permissible ripple current, reverse voltage may occur if the DC bias voltage is low.
1.4 Leakage current
There is a risk of leakage current characteristics increasing even if the following use environments are within
the stipulated range.
However, even if the leakage current increases, the SP-Cap self-repairing function will reduce the leakage
current in most cases when a voltage is applied.
(1) After re-flow
(2) Shelf conditions such as high temperature with no load, high temperature high humidity with no load and
sudden temperature changes.
1.5 Temperature
Use at or under the rated (guaranteed) temperature.
Operation at temperatures exceeding specifications causes large changes in the SP-Cap electrical properties,
and deterioration than can potentially lead to failure.
When calculating the operating temperature of the SP-Cap, be sure to include not only the ambient
temperature and internal temperature of the unit, but also radiation from heat generating elements inside the
unit (power transistors, resistors, etc.), and self-heating due to ripple current.
1.6 Calculation of the expected life time
Expected life is affected by operating temperature.
Generally, the capacitance change ratio will be 1/10 by each 20 °C reduction in temperature, so estimated life
time will be expected 10 times.
As below can be calculated the formula for expected life time LX (h) of SP-Cap at TX (°C) based on the
capacitance change ratio by temperature reduction.
Not guaranteed is the life time which is obtained by this formula as well as upper limit of valid expected life
time is 20 years.
Lx = L0×10
T0
Tx
L0
Lx
(°C)
(°C)
(h)
(h)
:
:
:
:
(T20-T )
0
x
Upper category temperature
Temperature in actual use (Temperature of SP-Cap)
Guaranteed life at (T0)
Life expectance in actual use (TX)
1.7 Failure rate
The majority of failure modes are short circuits or increases in leakage current.
The main factors of failure are mechanical stress, heat stress and electric stress due to re-flow and heat from
the use temperature environment.
Even within the stipulated limits, it is possible to lower the failure rate by reducing use conditions such as
temperature and voltage. Please be sure to have ample margin in your design.
[Expected Failure Rate]
(1) Date based on our reliability tests: 8.2 Fit or less (Based on applied rated voltage at 105 °C)
(2) Market failure rate: 0.13 Fit or less (Based on c=0, Reliability standard : 60 %)
1.8 Mounting area consideration
Isolate the surface of PCB under the mounted SP-Cap.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05
Mar. 2016
Conductive Polymer Aluminum Electrolytic Capacitors
2. Mounting
2.1 When mounting
(1)
(2)
(3)
(4)
Check the SP-Cap ratings (capacitance and voltage) before mounting.
Check the SP-Cap polarity before mounting.
Check the land size for the SP-Cap before mounting.
When using a mounter, if the pressure for mounting is too high, then the current leak may increase, shortcircuiting may occur, or the SP-Cap may break down or come off.
2.2 Soldering
(1) Reflow soldering
Be performed by one of following methods.
(a) Ambient heat conduction reflow (IR / Hot-air)
Please refer to the page of “Mounting Specifications”.
(b) Vapor phase reflow (but only allowable for CX, CT, SX, ST, GX, LX, LT and HX series).
Please contact Panasonic for details of allowable vapor phase reflow condition.
(2) Wave soldering and dip soldering
Please remind SP-Cap is NOT compatible.
(3) Hand soldering
Excessive force stress to the SP-Cap should be avoided
Conditions :
Tip temperature of soldering iron : 350 °C max.
Exposure time : 10 s max.
✽ Once removed from the printed circuit board for any reason, please do not use the SP-Cap again.
2.3 Land size
Refer to the land size of “Mounting specifications” for appropriate design dimensions.
Circuit board design requires examination of the most suitable dimensions taking conditions such as circuit
board, parts and reflow into consideration.
2.4 Mechanical stress
Do not apply excessive force to the SP-Cap this can damage the electrodes and badly affect the SP-Cap mount ability.
It can also cause the increase of leakage current, separation of the lead wire and element, and damage
to the SP-Cap body, all of which can badly affect the electrical performance of the SP-Cap.
2.5 Circuit board cleaning
SP-Cap should be cleaned after soldering in accordance with the following conditions.
Temperature : Less than 60 °C
Time
: Within 5min
Be sure to sufficiently wash and dry (20 min at 100 °C) the board afterward.
[Recommended Cleaning Solvents]
Pine Alpha ST-100S, Clean-thru 750H / 750L / 710M, Aqua Cleaner 210SEP, Sunelec B-12
DK Beclear CW-5790, Techno Cleaner 219, Cold Cleaner P3-375, Telpene Cleaner EC-7R
Technocare FRW-17 / FRW-1 / FRV-1, AXREL 32, IPA (Isopropyl alcohol)
(1) Consult our factory when performing processes with cleaning solvents other than those listed above or
deionized water.
(2) The use of ozone depleting cleaning agents are not recommended in the interest of protecting the
environment.
(3) In the case of using ultrasonic cleaning, the terminals may be broken. Therefore, please test before
using in mass production.
3. Usage environment of equipment
Avoid using equipment to which SP-Cap are fi ted in the following environments.
(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent.
(2) In direct sunlight, outdoors, or in dust.
(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a high
concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2.
(4) In an environment where strong static electricity or electromagnetic waves exist.
(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these SP-Cap.
(6) Sealing or coating of these SP-Cap or a printed circuit board on which these SP-Cap are mounted, with resin
and other material.
(7) Acid or alkaline environments.
(8) Environment subject to excessive vibration and shock.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
4. Storage
SP-Cap should be stored in a moisture proof environment. Storage conditions before and after opening the
moisture proof packaging as follows.
(If these conditions are exceeded, the package may absorb moisture and there is a risk of damage to the exterior
due to heat stress during mounting.)
[Environment of Storage]
Temperature: 5 °C to 30 °C without direct sunlight
Humidity : Less than 70 %
Maximum storage term before opening the package (2 years after manufactured)
Maximum storage condition after opening the package (7 days after opening)
SP-Cap should be all used within the storage term after opening the package.
5. Transportation
Take sufficient care during handling because excessive vibration, or shock can cause the reliability of the SP-Cap
to decrease.
6. Emergency procedures
If the SP-Cap is overheated, the resin case may emit smoke. If this occurs, immediately switch off the unit’s main
power supply to stop operation. Keep your face and hands away from the SP-Cap the temperature may be high
enough to cause the SP-Cap to ignite and burn.
7. Discarding
Since SP-Cap are composed of various metals and resins, treat them as industrial waste when arranging for their disposal.
The precautions for the use of functional polymer aluminum electrolytic capacitors follow the “Precautionary
guidelines for the use of fixed aluminum electrolytic capacitors for electronic equipment”, RCR- 2367B issued
by EIAJ in March 2002. Please refer to the above guidelines for details.
◇ Intellectual property right
We, Panasonic Group are providing the product and service that customers can use without anxiety, and are
working positively on the protection of our products under intellectual property rights.
Representative patents relating to SP-Cap are as follows :
US Patent No. 7136276
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Line up
Super low ESR/High ripple current
Conductive Polymer Aluminum Electrolytic Capacitors
Diagram
2-terminals
Standard Products
3-terminals
Low ESR Products
Low ESR/Low ESL Products✽
CX
Series
7.3×4.3×1.9 mm
GX
Series
7.3×4.3×1.9 mm
GX-L
Series
7.3×4.3×1.9 mm
2 V.DC/560 µF to 35 V.DC/22 µF
ESR : 12 mΩ to 40 mΩ
2 V.DC/560 µF to 2.5 V.DC/470 µF
ESR : 3 mΩ
2 V.DC/560 µF to 2.5 V.DC/470 µF
ESR : 3 mΩ
Low profile
Super Low
ESR
Super Low
ESR
CT
Series
7.3×4.3×1.4 mm
SX
Series
7.3×4.3×1.9 mm
LX
Series
7.3×4.3×1.9 mm
4 V.DC/180 µF to 35 V.DC/15 µF
ESR : 15 mΩ/40 mΩ
2 V.DC/560 µF to 6.3 V.DC/180 µF
ESR : 4.5 mΩ to 9 mΩ
2 V.DC/560 µF to 2.5 V.DC/470 µF
ESR : 4.5 mΩ/6 mΩ
Low profile
Low profile
CS
Series
7.3×4.3×1.1 mm
4 V.DC/120 µF to 35 V.DC/10 µF
ESR : 15 mΩ/40 mΩ
ST
Series
7.3×4.3×1.4 mm
LT
Series
7.3×4.3×1.4 mm
2 V.DC/330 µF to 2.5 V.DC/270 µF
ESR : 6 mΩ
2 V.DC/330 µF to 2.5 V.DC/270 µF
ESR : 6 mΩ
SS
Series
7.3×4.3×1.1 mm
LS
Series
7.3×4.3×1.1 mm
2 V.DC/220 µF to 2.5 V.DC/180 µF
ESR : 6 mΩ
2 V.DC/220 µF to 2.5 V.DC/180 µF
ESR : 6 mΩ
SR
Series
7.3×4.3×1.0 mm (max.)
LR
Series
7.3×4.3×1.0 mm (max.)
2 V.DC/220 µF to 6.3 V.DC/68 µF
ESR : 4.5 mΩ to 9 mΩ
2 V.DC/220 µF to 6.3 V.DC/68 µF
ESR : 4.5 mΩ to 9 mΩ
Guaranteed at 125 °C
HX
Series
7.3×4.3×1.9 mm
2 V.DC/560 µF to 25 V.DC/33 µF
ESR : 4.5 mΩ to 40 mΩ
✽ : ESL : 0.5nH (Typ.)
Old Series
Standard Products
CD
Series
7.3×4.3×1.8 mm
2 V.DC 220 µF to 16 V.DC 8.2 µF
ESR : 15 mΩ to 110 mΩ
Low Profile
FD Series
7.3×4.3×1.1 mm
2 V.DC 68 µF to 12.5 V.DC 15 µF
ESR : 28 mΩ to 40 mΩ
Low ESR Products
SL Series
7.3×4.3×1.9 mm
2 V.DC 220 µF to 6.3 V.DC 56 µF
ESR : 9 mΩ
UD Series
7.3×4.3×2.8 mm
2 V.DC 470 µF to 8 V.DC 100 µF
ESR : 9 mΩ to 18 mΩ
UE
Series
7.3×4.3×4.2 mm
2 V.DC 560 µF to 8 V.DC 150 µF
ESR : 7 mΩ to 15 mΩ
Miniaturization Products
MC Series
6.3×3.2×1.9 mm
2 V.DC 120 µF to 6.3 V.DC 47 µF
ESR : 12 mΩ to 18 mΩ
Please contact us when old
series is necessary.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Mounting Specifications
● Recommendable
reflow soldering
<Standard>
Temperature on the surface of capacitor (°C)
Soldering temperature and Soldering time
Peak temperature 260 °C
10 s max.
Temperature
Time
> 255 °C
> 230 °C
130 s max.
> 217 °C
150 s max.
Soldering
temperature
250
30 s max.
200
150
Soldering time
150 to 200 °C
180 s max.
100
Sp-Cap recommended
profile condition of the
IPC/J-STD-020D standard
50
Time (s)
Reflow cycle : 3 max.
EX.)
Peak temperature
10 s max.
Peak temperature
Time in 230 °C or more
260 °C, 10 s max.
40 s max.
250 °C, 10 s max.
60 s max.
250
200
150
Time in 230 °C
or more
150 to 200 °C
120 s max.
100
50
Time (s)
270
260
250
240
230
0
Reflow cycle : 2 max.
● Typical
Peak temperature (°C)
Temperature on the surface of capacitor (°C)
<260 °C>
10
20 30 40 50 60 70
Time in 230 °C or more (s)
land pattern
For standard terminal (2-terminals)
a
c
b
Unit : mm
Capacitor
Series
a
b
c
Standard (Except MC)
8.8
4.0
2.8
(MC)
7.2
2.6
2.2
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
● Typical
● VIA
land pattern
For Low ESL terminal (3-terminals)
(LR, LS, LT, LX, GX-L series)
For Low ESL terminal (3-terminals)
(LR, LS, LT, LX, GX-L series)
Unit : mm
Unit : mm
VIA(+)10-00.4
8.8
4.0
2.7
VIA(–)10-00.4
–
1.3
0.5
–
+
–
–
1.15
1.9
2.8
5.1
+
Capacitor
0.9 0.9
Capacitor
0.9 0.9 0.9
0.5
0.3
0.3
Packaging Specifications
● Reel
● Embossed
Dimensions
Taping
0D0 (Feeding hole)
P0
P2
Tape running direction
b
E
t
F
–
A
W
E
0C
a
0A
0B
a
+
0D
R:1.0
P1
b
Chip pocket
B
b-b
Cross section
a-a
Cross section
Unit : mm
W
A
B
W
F
E
P1
Standard (MC series) Standard (MC series)
7.6±0.2 6.3±0.3 4.5±0.2 3.6±0.3 12.0±0.3 5.5±0.1 1.75±0.10 8.0±0.1
t
Unit : mm
0A
0B
0330 330
80
Reel
0C
0D
E
13±0.5 21±0.8 2±0.5
W
t
14
3
P2
P0
0D0
2.0±0.1 4.0±0.1 1.5+0.1
0
Upper row : Product height (mm) / Lower berth : t
to 1.1 1.4 to 1.9 2.8
4.2 (MC series)
1.5±0.2 2.4±0.2 3.5±0.2 4.3±0.2 2.8±0.3
a
Packaging Box Dimensions
c
Unit : mm
Reel
b
0330
a
b
c
400 max. 400 max. 135 max.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Surface Mount Type
Series :
CS, CT, CX
Features
● High
voltage (35 V.DC max.)
profile (Height 1.0 mm max.)
● High ripple current (5600 mAr.m.s. max.)
● RoHS compliance, Halogen free
● Low
Specifications
Series
CS
CT
Category temp. range
CX
–55 °C to +105 °C
Rated voltage range
4 V.DC to 35 V.DC
Nominal cap.range
10 μF to 120 μF
2 V.DC to 35 V.DC
15 μF to 180 μF
15 μF to 560 μF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
DC leakage current
I < 0.1 CV (μA) [2 V.DC to 6.3 V.DC, 2 minutes], I < 0.3 CV (μA) [10 V.DC to 35 V.DC, 2 minutes]
Dissipation factor (tan d)
< 0.06 (120 Hz / + 20 °C)
Surge voltage (V.DC)
Rated voltage × 1.25 [2 V.DC to 16 V.DC], × 1.15 [20 V.DC to 35 V.DC] (15 °C to 35 °C)
+105 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Endurance
< 2 times of the initial limit
2 V.DC to 6.3 V DC : < 3 times of the initial limit
DC leakage current
10 V.DC to 35 V.DC : Within the initial limit
+60 °C, 90 %, 500 h, No-applied voltage
tan d
Capacitance change
of initial measurd value
Damp heat
(Steady state)
2 V.DC to 2.5 V.DC
4 V.DC, 10 V.DC to 35 V.DC
6.3 V.DC
+70 %, –20 %
+60 %, –20 %
+50 %, –20 %
< 2 times of the initial limit
2 V.DC to 6.3 V.DC : Within the initial limit
DC leakage current
10 V.DC to 35V DC : < 3 times of the initial limit
tan d
Marking
Dimensions (not to scale)
–
H
+
Cap.
Polarity bar (Positive)
P
P
L
Lot No.
W2
W2
W1
R.V. code
Unit : mm
Series
CS
Rated voltage mark
d
e
g
2 V.DC
2.5 V.DC
4 V.DC
j
A
C
6.3 V.DC
10 V.DC
16 V.DC
D
E
V
20 V.DC
25 V.DC
35 V.DC
L±0.2 W1±0.2 W2±0.1 H±0.1
7.3
4.3
2.4
1.1
P±0.3
1.3
CT
7.3
4.3
2.4
1.4
1.3
CX
7.3
4.3
2.4
1.9
1.3
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
07 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Characteristics list
Reflow ✽3
Case size (mm)
Series
Rated Capacitance
voltage
(±20 %)
(V.DC)
(μF)
✽1
L
W
H
Part number
Min.✽4
Packaging
Q’ty
(pcs)
✽2
Ripple
ESR
current
(mAr.m.s.) (mΩ max.)
5100
15
4
120
7.3
4.3
1.1
EEFCS0G121R
3500
6.3
68
7.3
4.3
1.1
5100
15
EEFCS0J680R
3500
10
47
7.3
4.3
1.1
3200
40
EEFCS1A470R
3500
15
7.3
4.3
1.1
3200
40
EEFCS1C150R
3500
16
22
7.3
4.3
1.1
3200
40
EEFCS1C220R
3500
33
7.3
4.3
1.1
3200
40
EEFCS1C330R
3500
10
7.3
4.3
1.1
3200
40
EEFCS1D100R
3500
CS
20
15
7.3
4.3
1.1
3200
40
EEFCS1D150R
3500
22
7.3
4.3
1.1
3200
40
EEFCS1D220R
3500
10
7.3
4.3
1.1
3200
40
EEFCS1E100R
3500
15
7.3
4.3
1.1
3200
40
EEFCS1E150R
3500
35
10
7.3
4.3
1.1
3200
40
EEFCS1V100R
3500
4
180
7.3
4.3
1.4
5100
15
EEFCT0G181R
3500
6.3
100
7.3
4.3
1.4
5100
15
EEFCT0J101R
3500
10
68
7.3
4.3
1.4
3200
40
EEFCT1A680R
3500
16
47
7.3
4.3
1.4
3200
40
EEFCT1C470R
3500
25
CT
Specification
<Standard>
33
7.3
4.3
1.4
3200
40
EEFCT1D330R
3500
47
7.3
4.3
1.4
3200
40
EEFCT1D470R
3500
25
22
7.3
4.3
1.4
3200
40
EEFCT1E220R
3500
35
15
7.3
4.3
1.4
3200
40
EEFCT1V150R
3500
20
✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact us when 500 pcs packing is necessary.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
07 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Characteristics list
Reflow ✽3
Case size (mm)
Series
Rated Capacitance
voltage
(±20 %)
(V.DC)
(μF)
220
270
2
2.5
330
390
470
560
220
330
390
470
150
180
4
220
270
330
100
120
CX
6.3
10
16
20
25
35
150
180
220
47
68
100
15
22
33
47
68
22
33
47
56
15
22
33
15
22
Specification
✽1
L
W
H
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
Part number
Min.✽4
Packaging
Q’ty
(pcs)
EEFCX0D221R
EEFCX0D271XR
EEFCX0D331R
EEFCX0D331XR
EEFCX0D391R
EEFCX0D471R
EEFCX0D561R
EEFCX0E221R
EEFCX0E331R
EEFCX0E391R
EEFCX0E471R
EEFCX0G151R
EEFCX0G181R
EEFCX0G181XR
EEFCX0G221R
EEFCX0G221XR
EEFCX0G271R
EEFCX0G331R
EEFCX0J101R
EEFCX0J121R
EEFCX0J151R
EEFCX0J151XR
EEFCX0J181R
EEFCX0J221R
EEFCX1A470R
EEFCX1A680R
EEFCX1A101R
EEFCX1C150R
EEFCX1C220R
EEFCX1C330R
EEFCX1C470R
EEFCX1C680R
EEFCX1D220R
EEFCX1D330R
EEFCX1D470R
EEFCX1D560R
EEFCX1E150R
EEFCX1E220R
EEFCX1E330R
EEFCX1V150R
EEFCX1V220R
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
✽2
Ripple
ESR
current
(mAr.m.s.) (mΩ max.)
5100
15
5600
12
5100
15
5600
12
5100
15
5100
15
5100
15
5100
15
5100
15
5100
15
5100
15
5100
15
5100
15
5600
12
5100
15
5600
12
5100
15
5100
15
5100
15
5100
15
5100
15
5600
12
5100
15
5100
15
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
3200
40
<Standard>
✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact us when 500 pcs packing is necessary.
Temperature compensation multipliers for ripple current
Temp.
2 V.DC to 6.3 V.DC
10 V.DC to 35 V.DC
Coefficient
T < 45 °C
45 °C < T < 85 °C
85 °C < T < 105 °C
1.0
0.7
0.25
1.0
0.8
0.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
07 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Surface Mount Type
Series :
SX (Low ESR Products)
Features
● Large
capacitance (560 μF max.)
ESR (4.5 mΩ to 9 mΩ)
● High ripple current (8500 mAr.m.s. max.)
● RoHS compliance, Halogen free
● Low
Specifications
Series
Category temp. range
Rated voltage range
Nominal cap.range
Capacitance tolerance
DC leakage current
Dissipation factor (tan d)
Surge voltage (V.DC)
Endurance
Damp heat
(Steady state)
SX
–55 °C to +105 °C
2 V.DC to 6.3 V.DC
82 μF to 560 μF
±20 % (120 Hz/+20 °C)
I < 0.1 CV (μA) 2 minutes
< 0.06 (120 Hz/+20 °C)
Rated voltage × 1.25 (15 °C to 35 °C)
+105 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 2 times of the initial limit
DC leakage current
< 3 times of the initial limit
+60 °C, 90 %, 500 h, No-applied voltage
2 to 2.5 V.DC
4 V.DC
Capacitance change of
initial measurd value
+70 %, –20 %
+60 %, –20 %
tan d
< 2 times of the initial limit
DC leakage current
Within the initial limit
Marking
6.3 V.DC
+50 %, –20 %
Dimensions (not to scale)
–
+
H
Cap.
Polarity bar (Positive)
P
P
Lot No.
W1
W2
W2
L
R.V. code
Rated voltage mark
d
e
g
j
2 V.DC
2.5 V.DC
4 V.DC
6.3 V.DC
Unit : mm
Series
SX
L±0.2 W1±0.2 W2±0.1 H±0.1
7.3
4.3
2.4
1.9
P±0.3
1.3
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05
Jan. 2016
Conductive Polymer Aluminum Electrolytic Capacitors
Characteristics list
Reflow ✽3
Case size (mm)
Series
Rated Capacitance
voltage
(±20 %)
(V.DC)
(μF)
180
220
270
330
2
390
470
560
150
180
220
SX
270
2.5
330
390
470
82
100
4
6.3
150
180
220
270
120
150
180
<Standard>
Specification
✽1
L
W
H
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
Part number
Min.✽4
Packaging
Q’ty
(pcs)
EEFSX0D181ER
EEFSX0D221ER
EEFSX0D271ER
EEFSX0D271XE
EEFSX0D271E4
EEFSX0D331ER
EEFSX0D331XE
EEFSX0D331E4
EEFSX0D391ER
EEFSX0D391XE
EEFSX0D391E4
EEFSX0D471ER
EEFSX0D471XE
EEFSX0D471E4
EEFSX0D561E4
EEFSX0E151ER
EEFSX0E181ER
EEFSX0E221ER
EEFSX0E221E7
EEFSX0E271E7
EEFSX0E331ER
EEFSX0E331XE
EEFSX0E331E4
EEFSX0E391ER
EEFSX0E391XE
EEFSX0E391E4
EEFSX0E471ER
EEFSX0E471XE
EEFSX0E471E4
EEFSX0G820ER
EEFSX0G101ER
EEFSX0G151ER
EEFSX0G151E7
EEFSX0G181ER
EEFSX0G221ER
EEFSX0G271ER
EEFSX0J121E7
EEFSX0J151ER
EEFSX0J181ER
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
✽2
Ripple
ESR
current
(mAr.m.s.) (mΩ max.)
6300
9
6300
9
6300
9
7500
6
8500
4.5
6300
9
7500
6
8500
4.5
6300
9
7500
6
8500
4.5
6300
9
7500
6
8500
4.5
8500
4.5
6300
9
6300
9
6300
9
7000
7
7000
7
6300
9
7500
6
8500
4.5
6300
9
7500
6
8500
4.5
6300
9
7500
6
8500
4.5
6300
9
6300
9
6300
9
7000
7
6300
9
6300
9
6300
9
7000
7
6300
9
6300
9
✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact us when 500 pcs packing is necessary.
Temperature compensation multipliers for ripple current
Temp.
T < 45 °C
45 °C < T < 85 °C
85 °C < T < 105 °C
Coefficient
1.0
0.7
0.25
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05
Jan. 2016
Conductive Polymer Aluminum Electrolytic Capacitors
Surface Mount Type
Series :
GX (Super Low ESR Products)
Features
● Large
capacitance (560 μF max.)
Low ESR (3 mΩ max.)
● Low ESL ( 3-terminals : 50 % less than 2-terminals) [Suffix : L]
● High ripple current (10200 mAr.m.s. max.)
● RoHS compliance, Halogen free
● Super
Specifications
Series
Category temp. range
Rated voltage range
Nominal cap.range
Capacitance tolerance
DC leakage current
Dissipation factor (tan d)
Surge voltage (V.DC)
Endurance
Damp heat
(Steady state)
GX
–55 °C to +105 °C
2 V.DC to 2.5 V.DC
330 μF to 560 μF
±20 % (120 Hz/+20 °C)
I < 0.1 CV (μA) 2 minutes
< 0.06 (120 Hz/+20 °C)
Rated voltage × 1.25 (15 °C to 35 °C)
+105 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 2 times of the initial limit
DC leakage current
< 3 times of the initial limit
+60 °C, 90 %, 500 h, No-applied voltage
Capacitance change of 2 V.DC to 2.5 V.DC
initial measurd value
+70 %, –20 %
tan d
< 2 times of the initial limit
DC leakage current
Within the initial limit
Marking
Cap.
Polarity bar (Positive)
Lot No.
Rated voltage mark
d
2 V.DC
e
2.5 V.DC
R.V. code
Dimensions (not to scale)
2 terminals
3 terminals
+
+
–
H
H
–
P
P
L
L
W1
P4
W2
W2
+
W2
–
W2
W1
P1
P3
P2 P1
Unit : mm
Series
GX
L±0.2
7.3
W1±0.2 W2±0.1 H±0.1
4.3
2.4
1.9
✽ Externals of figure are the reference.
P±0.3
1.3
Unit : mm
Series L±0.2 W1±0.2 W2±0.1 H±0.1 P1±0.3 P2±0.1 P3±0.2 P4±0.2
GX
7.3
4.3
2.4
1.9
1.3
1.1
0.7
1.4
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Characteristics list
Case size (mm)
Series
Rated Capacitance
(±20 %)
voltage
(V.DC)
(μF)
330
2
GX
470
560
2.5
470
Specification
✽1
L
7.3
7.3
7.3
7.3
7.3
7.3
7.3
W
4.3
4.3
4.3
4.3
4.3
4.3
4.3
H
1.9
1.9
1.9
1.9
1.9
1.9
1.9
✽2
Ripple
ESR
current
(mAr.m.s.) (mΩ max.)
10200
3
10200
3
10200
3
10200
3
10200
3
10200
3
10200
3
The number
of
terminals
2
Reflow ✽3
<Standard>
Part number
Min.✽4
Packaging
Q’ty
(pcs)
EEFGX0D331R
EEFGX0D471R
EEFGX0D471L
EEFGX0D561R
EEFGX0D561L
EEFGX0E471R
EEFGX0E471L
3500
3500
3500
3500
3500
3500
3500
3
○
○
○
○
○
○
○
✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact us when 500 pcs packing is necessary.
Temperature compensation multipliers for ripple current
Temp.
T < 45 °C
45 °C < T < 85 °C
85 °C < T < 105 °C
Coefficient
1.0
0.7
0.25
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Surface Mount Type
Series :
LX (Low ESR / Low ESL Products)
Features
● Large
capacitance (560 μF max.)
ESR (4.5 mΩ, 6 mΩ)
● Low ESL (3-terminals : 50 % less than 2-terminals)
● High ripple current (8500 mAr.m.s. max.)
● RoHS compliance, Halogen free
● Low
Specifications
Series
Category temp. range
Rated voltage range
Nominal cap.range
Capacitance tolerance
DC leakage current
Dissipation factor (tan d)
Surge voltage (V.DC)
Endurance
Damp heat
(Steady state)
LX
–55 °C to +105 °C
2 V.DC to 2.5 V.DC
330 μF to 560 μF
±20 % (120 Hz/+20 °C)
I < 0.1 CV (μA) 2 minutes
< 0.06 (120 Hz/+20 °C)
Rated voltage × 1.25 (15 °C to 35 °C)
+105 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 2 times of the initial limit
DC leakage current
< 3 times of the initial limit
+60 °C, 90 %, 500 h, No-applied voltage
Capacitance change of 2 V.DC to 2.5 V.DC
initial measurd value
+70 %, –20 %
tan d
< 2 times of the initial limit
DC leakage current
Within the initial limit
Marking
Dimensions (not to scale)
–
H
+
Cap.
Polarity bar (Positive)
L
W1
P4
Lot No.
W2
+
W2
–
P1
R.V. code
P3
P2 P1
Unit : mm
Rated voltage mark
d
e
2 V.DC
2.5 V.DC
Series L±0.2 W1±0.2 W2±0.1 H±0.1 P1±0.3 P2±0.1 P3±0.2 P4±0.2
LX
7.3
4.3
2.4
1.9
1.3
1.1
0.7
1.4
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Characteristics list
Reflow ✽3
Case size (mm)
Series
Rated Capacitance
voltage
(±20 %)
(V.DC)
(μF)
330
2
LX
470
560
330
2.5
470
<Standard>
Specification
✽1
L
W
H
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
Part number
Min.✽4
Packaging
Q’ty
(pcs)
EEFLX0D331R
EEFLX0D331R4
EEFLX0D471R
EEFLX0D471R4
EEFLX0D561R
EEFLX0D561R4
EEFLX0E331R
EEFLX0E331R4
EEFLX0E471R
EEFLX0E471R4
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
✽2
Ripple
ESR
current
(mAr.m.s.) (mΩ max.)
7500
6
8500
4.5
7500
6
8500
4.5
7500
6
8500
4.5
7500
6
8500
4.5
7500
6
8500
4.5
✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact us when 500 pcs packing is necessary.
Temperature compensation multipliers for ripple current
Temp.
T < 45 °C
45 °C < T < 85 °C
85 °C < T < 105 °C
Coefficient
1.0
0.7
0.25
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Surface Mount Type
Series :
SR, LR, SS, LS, ST, LT
Features
● Low profile (Height 1.0 mm max.)
● Low ESR (4.5 mΩ to 9 mΩ)
● Low ESL (3-terminals : 50% less then 2-terminals)
● High ripple current (8500 mAr.m.s. max.)
● RoHS compliance, Halogen free
[LR, LS, LT series]
Specifications
Series
Category temp. Range
Rated voltage range
Nominal cap.Range
Capacitance tolerance
DC leakage current
Dissipation factor (tan d)
Surge voltage (V.DC)
Endurance
Damp heat
(Steady state)
SR
LR
SS
LS
ST
LT
–55 °C to +105 °C
2 V.DC to 6.3 V.DC
2 V.DC to 2.5 V.DC
68 μF to 220μF
180 μF to 220μF
270 μF to 330 μF
±20 % (120 Hz / + 20 °C)
I < 0.1 CV (μA) 2 minutes
< 0.06 (120 Hz/+20 °C)
Rated voltage × 1.25 (15 °C to 35 °C)
+105 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 2 times of the initial limit
DC leakage current
< 3 times of the initial limit
+60 °C, 90 %, 500 h, No-applied voltage
2 V.DC to 2.5 V.DC
4 V.DC
6.3 V.DC
Capacitance change of
initial measurd value
+70 %, –20 %
+60 %, –20 %
+50 %, –20 %
tan d
< 2 times of the initial limit
DC leakage current
Within the initial limit
Marking
Cap.
Polarity bar (Positive)
Rated voltage mark
Lot No.
d
e
g
j
R.V. code
2 V.DC
2.5 V.DC
4 V.DC
6.3 V.DC
Dimensions (not to scale)
SR, SS, ST series
LR, LS, LT series
+
–
+
H
H
–
L
P4
P
W1
P1
P3
Unit : mm
Series
SR
SS
ST
L±0.2
7.3
7.3
7.3
W1±0.2 W2±0.1
4.3
2.4
4.3
2.4
4.3
2.4
✽ Externals of figure are the reference.
W1
+
W2
–
W2
W2
L
W2
P
H±0.1
1.0 ✽1
1.1
1.4
P±0.3
1.3
1.3
1.3
✽1 : Maximum
P2 P1
Unit : mm
Series
LR
LS
LT
L±0.2 W1±0.2 W2±0.1
7.3 4.3 2.4
7.3 4.3 2.4
7.3 4.3 2.4
H±0.1
1.0 ✽1
1.1
1.4
✽ Externals of figure are the reference.
P1±0.3 P2±0.1 P3±0.2 P4±0.2
1.3 1.1 0.7 1.4
1.3 1.1 0.7 1.4
1.3 1.1 0.7 1.4
✽1 : Maximum
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Characteristics list
Case size (mm)
Series
SR
LR
SS
LS
ST
LT
Rated Capacitance
voltage
(±20 %)
(V.DC)
(μF)
2
220
2.5
180
4
6.3
120
68
2
220
2.5
180
4
6.3
2
2.5
2
2.5
2
2.5
2
2.5
120
68
220
180
220
180
330
270
330
270
Specification
✽1
L
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
W
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
H
1.0 max.
1.0 max.
1.0 max.
1.0 max.
1.0 max.
1.0 max.
1.0 max.
1.0 max.
1.0 max.
1.0 max.
1.0 max.
1.0 max.
1.1
1.1
1.1
1.1
1.4
1.4
1.4
1.4
✽2
Ripple
ESR
current
(mAr.m.s.) (mΩ max.)
7500
6
8500
4.5
7500
6
8500
4.5
6300
9
6300
9
7500
6
8500
4.5
7500
6
8500
4.5
6300
9
6300
9
7500
6
7500
6
7500
6
7500
6
7500
6
7500
6
7500
6
7500
6
The number
of
terminals
2
Reflow ✽3
<Standard>
Part number
Min.✽4
Packaging
Q’ty
(pcs)
EEFSR0D221R
EEFSR0D221R4
EEFSR0E181R
EEFSR0E181R4
EEFSR0G121R
EEFSR0J680R
EEFLR0D221R
EEFLR0D221R4
EEFLR0E181R
EEFLR0E181R4
EEFLR0G121R
EEFLR0J680R
EEFSS0D221R
EEFSS0E181R
EEFLS0D221R
EEFLS0E181R
EEFST0D331R
EEFST0E271R
EEFLT0D331R
EEFLT0E271R
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact us when 500 pcs packing is necessary.
Temperature compensation multipliers for ripple current
Temp.
T < 45 °C
45 °C < T < 85 °C
85 °C < T < 105 °C
Coefficient
1.0
0.7
0.25
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Surface Mount Type
Series :
HX (Guaranteed at 125 °C)
Features
● Endurance
125 °C 1000 h
voltage & Large capacitance (2 V.DC 560 μF to 25 V.DC 33 μF)
● Low ESR (4.5 mΩ max.)
● RoHS compliance, Halogen free
● High
Specifications
Series
Category temp. range
Rated voltage range
Category voltage range
Nominal cap.range
Capacitance tolerance
DC leakage current
Dissipation factor (tan d)
Surge voltage (V.DC)
Endurance
Damp heat
(Steady state)
HX
–55 °C to +125 °C
2 V.DC to 2.5 V.DC, 10 V.DC to 25 V.DC
1.6 V.DC to 2 V.DC, 8 V.DC to 20 V.DC
15 μF to 560 μF
±20 % (120 Hz/+20 °C)
2 V.DC to 2.5 V.DC : I < 0.1 CV (μA) 2 minutes, 10 V.DC to 25 V.DC : I < 0.3 CV (μA) 2 minutes
< 0.1 (120 Hz/+20 °C)
Rated voltage × 1.25 [2 V.DC to 16 V.DC], × 1.15 [20 V.DC to 25 V.DC](15 °C to 35 °C)
+125 °C, 1000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 2 times of the initial limit
DC leakage current
Within the initial limit
After storing for 500 hours at +60 °C, 90 %
2 V.DC to 2.5 V.DC
10 V.DC to 25 V.DC
Capacitance change of
initial measurd value
+70 %, –20 %
+60 %, –20 %
tan d
< 2 times of the initial limit
2 V.DC to 2.5 V.DC : Within the initial limit
DC leakage current
10 V.DC to 25V DC : < 3 times of the initial limit
Marking
Dimensions (not to scale)
–
+
H
Cap.
Polarity bar (Positive)
P
P
Lot No.
W1
W2
W2
L
R.V. code
Rated voltage mark
d
e
A
2 V.DC
2.5 V.DC
10 V.DC
Unit : mm
C
D
E
16 V.DC
20 V.DC
25 V.DC
Series
HX
L±0.2 W1±0.2 W2±0.1 H±0.1
7.3
4.3
2.4
1.9
P±0.3
1.3
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03 Nov. 2015
Conductive Polymer Aluminum Electrolytic Capacitors
Characteristics list
Reflow ✽3
Series
Rated
voltage
[105 °C]
(V.DC)
Category
Capacitance
voltage
(±20 %)
[125 °C]
(μF)
(V.DC)
470
2
1.6
560
330
2.5
2
470
47
HX
10
16
20
25
8
12.8
16
20
Case size (mm)
Specification
✽1
L
W
H
7.3
4.3
1.9
7.3
4.3
1.9
✽2
Ripple
ESR
current
(mAr.m.s.) (mΩ max.)
5100
15
6300
9
Part number
<Standard>
Min.✽4
Packaging
Q’ty
(pcs)
EEFHX0D471R
3500
EEFHX0D471R9
3500
7.3
4.3
1.9
7500
6
EEFHX0D471R6
3500
7.3
4.3
1.9
8500
4.5
EEFHX0D471R4
3500
7.3
4.3
1.9
5100
15
EEFHX0D561R
3500
7.3
4.3
1.9
8500
4.5
EEFHX0D561R4
3500
7.3
4.3
1.9
5100
15
EEFHX0E331R
3500
7.3
4.3
1.9
6300
9
EEFHX0E331R9
3500
7.3
4.3
1.9
7500
6
EEFHX0E331R6
3500
7.3
4.3
1.9
8500
4.5
EEFHX0E331R4
3500
7.3
4.3
1.9
5100
15
EEFHX0E471R
3500
7.3
4.3
1.9
6300
9
EEFHX0E471R9
3500
7.3
4.3
1.9
7500
6
EEFHX0E471R6
3500
7.3
4.3
1.9
8500
4.5
EEFHX0E471R4
3500
7.3
4.3
1.9
3200
40
EEFHX1A470R
3500
68
7.3
4.3
1.9
3200
40
EEFHX1A680R
3500
100
7.3
4.3
1.9
3200
40
EEFHX1A101R
3500
15
7.3
4.3
1.9
3200
40
EEFHX1C150R
3500
22
7.3
4.3
1.9
3200
40
EEFHX1C220R
3500
33
7.3
4.3
1.9
3200
40
EEFHX1C330R
3500
47
7.3
4.3
1.9
3200
40
EEFHX1C470R
3500
68
7.3
4.3
1.9
3200
40
EEFHX1C680R
3500
22
7.3
4.3
1.9
3200
40
EEFHX1D220R
3500
33
7.3
4.3
1.9
3200
40
EEFHX1D330R
3500
47
7.3
4.3
1.9
3200
40
EEFHX1D470R
3500
56
7.3
4.3
1.9
3200
40
EEFHX1D560R
3500
15
7.3
4.3
1.9
3200
40
EEFHX1E150R
3500
22
7.3
4.3
1.9
3200
40
EEFHX1E220R
3500
33
7.3
4.3
1.9
3200
40
EEFHX1E330R
3500
45 °C < T < 85 °C 85 °C < T < 105 °C
125 °C < T
✽1: Ripple current (100 kHz/ +45°C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact us when 500 pcs packing is necessary.
Temperature compensation multipliers for ripple current
Temp.
2 V.DC to 2.5 V.DC
10 V.DC to 25 V.DC
Coefficient
T < 45 °C
1.0
0.7
0.25
0.25
1.0
0.8
0.5
0.25
Ripple current should be controlled so that surface temperature of capacitor does not exceed the category temperature.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03 Nov. 2015
SP-Cap/ Conductive Polymer Aluminum Capacitors (Specialty Polymer Aluminum Capacitors)
Surface Mount Type
Series:
FD, CD, UD, UE
Old series
[Our Requests]
Since this series is old, we don't recommend you to adopt it
but CX & SX series for your new design.
■ Features
● Low ESR
● Excellent Noise-absorbent Characteristics
● RoHS directive compliant
■ Specifications
Series & Size Code
FD
CD
Category Temp. Range
UD
UE
–40 °C to +105 °C
Rated Voltage Range
2 V.DC to 12.5 V.DC
2 V.DC to 16 V.DC
2 V.DC to 8 V.DC
2 V.DC to 8 V.DC
Nominal Cap.Range
15 μF to 68 μF
2.2 μF to 220 μF
68 μF to 470 μF
100 μF to 560 μF
Capacitance Tolerance
±20 %
Reflow 240 °C : I < 0.06 CV (μA) 2minutes (2 V.DC to 4 V.DC)
I < 0.04 CV or 3 (μA) 2 minutes (6.3 V.DC to 16 V.DC) (Whichever is greater)
Reflow 260 °C : I < 0.1 CV (μA) 2 minutes
< 0.06 (120 Hz/+20 °C)
<0.10 (120 Hz/+20 °C)
DC Leakage Current
tan d
Surge Voltage
Rated Voltage × 1.25 (15 °C to 35 °C)
After applying rated voltage for 1000 hours at 105 °C±2 °C, and then being stabilized at +20 °C,
capacitor shall meet the following limits.
Endurance
Capacitance change
±10% of initial measured value
tan d
< Initial specified value
DC leakage current
< Initial specified value
After storing for 500 hours at 60 °C, 90 %
Moisture resistance
Capacitance change of
initial measurd value
2, 2.5 V.DC
4 V.DC
6.3 V.DC
8 V.DC to 16 V.DC
+70, –20 %
+60, –20 %
+50, –20 %
+40, –20 %
tan d
< 200 % of initial specified value
DC leakage current
< Initial specified value
■ Marking
■ Dimensions in mm(not to scale)
–
(Unit : mm)
H
+
P
P
W1
Lot No.
R.V. code
Series &
Size Code
FD
CD
UD
UE
W2
Polarity bar (Positive)
W2
Cap.
L
L±0.2 W1±0.2 W2±0.1
7.3
7.3
7.3
7.3
4.3
4.3
4.3
4.3
2.4
2.4
2.4
2.4
H
P±0.3
1.1±0.1
1.8±0.1
2.8±0.2
4.2±0.1
1.3
1.3
1.3
1.3
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02 Mar. 2015
– EEF-16 –
SP-Cap/ Conductive Polymer Aluminum Capacitors (Specialty Polymer Aluminum Capacitors)
■ Standard Products
Series &
Size Code
CapaciRated
tance
Voltage
(±20 %)
(V.DC)
(μF)
2
2.5
FD
4
6.3
8
12.5
68
56
39
47
33
22
15
100
2
120
150
180
220
82
2.5
100
120
150
56
4
68
82
CD
6.3
100
10
22
33
47
68
8
10
12.5
16
8.2
15
22
33
47
22
33
39
4.7
10
15
22
2.2
4.7
6.8
8.2
330
2
390
470
UD
2.5
220
270
Reflow ✽3
Case Size
Specification
L
(mm)
W
(mm)
H
(mm)
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
✽1
✽2
Ripple
ESR
current
(Ar.m.s.) (mΩ max.)
2.0
2.0
2.0
2.0
2.0
2.0
1.4
2.5
2.7
2.5
2.7
2.5
2.5
2.5
2.5
2.7
2.5
2.7
2.5
2.5
2.5
2.7
2.5
2.7
2.5
2.7
2.5
1.4
1.6
2.0
2.5
2.7
2.5
2.7
1.4
1.6
2.0
2.5
1.8
1.6
1.8
1.8
1.0
1.0
1.3
1.6
1.0
1.0
1.0
1.3
3.0
3.3
3.4
3.0
3.4
3.4
3.0
3.3
3.4
3.0
3.4
28
28
28
28
28
28
40
18
15
18
15
18
18
18
18
15
18
15
18
18
18
15
18
15
18
15
18
55
40
28
18
15
18
15
55
40
28
18
25
30
25
25
80
60
50
30
110
80
70
45
15
12
9
15
9
9
15
12
9
15
9
Reflow
Part number
EEFFD0D680R
EEFFD0E560R
EEFFD0G390R
EEFFD0G470R
EEFFD0J330R
EEFFD0K220R
EEFFD1B150R
EEFCD0D101ER
EEFCD0D101XE
EEFCD0D121ER
EEFCD0D121XE
EEFCD0D151ER
EEFCD0D181ER
EEFCD0D221ER
EEFCD0E820ER
EEFCD0E820XE
EEFCD0E101ER
EEFCD0E101XE
EEFCD0E121ER
EEFCD0E151ER
EEFCD0G560ER
EEFCD0G560XE
EEFCD0G680ER
EEFCD0G680XE
EEFCD0G820ER
EEFCD0G820XE
EEFCD0G101ER
EEFCD0J100ER
EEFCD0J220ER
EEFCD0J330ER
EEFCD0J470ER
EEFCD0J470XE
EEFCD0J680ER
EEFCD0J680XE
EEFCD0K8R2ER
EEFCD0K150ER
EEFCD0K220ER
EEFCD0K330ER
EEFCD0K470ER
EEFCD1A220ER
EEFCD1A330ER
EEFCD1A390ER
EEFCD1B4R7R
EEFCD1B100R
EEFCD1B150R
EEFCD1B220R
EEFCD1C2R2R
EEFCD1C4R7R
EEFCD1C6R8R
EEFCD1C8R2R
EEFUD0D331ER
EEFUD0D331XE
EEFUD0D331LE
EEFUD0D391ER
EEFUD0D391LE
EEFUD0D471LE
EEFUD0E221ER
EEFUD0E221XE
EEFUD0E221LE
EEFUD0E271ER
EEFUD0E271LE
✽4
240 °C
260 °C
◯
◯
◯
◯
◯
◯
◯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
◯
◯
◯
◯
◯
◯
◯
◯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
—
—
—
—
—
—
—
—
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
<260 °C>
Min.
Packaging
Q’ty
(pcs)
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
✽1: Ripple current (100 kHz/ +20 to +105 °C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact Panasonic for details of allowable 240 °C reflow condition.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02 Mar. 2015
– EEF-17 –
SP-Cap/ Conductive Polymer Aluminum Capacitors (Specialty Polymer Aluminum Capacitors)
■ Standard Products
Series &
Size Code
CapaciRated
tance
Voltage
(±20 %)
(V.DC)
(μF)
120
4
150
180
100
UD
6.3
120
150
8
68
100
270
330
2
390
470
560
220
270
2.5
330
390
UE
470
180
4
220
270
330
150
6.3
180
220
8
100
150
Reflow ✽3
Case Size
Specification
L
(mm)
W
(mm)
H
(mm)
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
✽1
✽2
Ripple
ESR
current
(Ar.m.s.) (mΩ max.)
3.0
3.4
3.0
3.3
3.4
2.5
3.4
3.0
3.3
3.0
3.3
3.4
2.5
3.4
3.0
2.5
3.3
3.5
3.3
3.5
3.3
3.5
3.7
3.3
3.5
3.7
3.3
3.7
3.3
3.5
3.3
3.5
3.3
3.5
3.7
3.3
3.7
3.3
3.7
3.3
3.5
3.3
3.5
3.7
3.3
3.7
3.3
3.3
3.5
3.3
3.5
3.7
3.0
3.7
3.3
3.0
15
12
15
12
9
18
9
15
12
15
12
9
18
9
15
18
12
10
12
10
12
10
7
12
10
7
12
7
12
10
12
10
12
10
7
12
7
12
7
12
10
12
10
7
12
7
12
12
10
12
10
7
15
7
12
15
Reflow
Part number
EEFUD0G121ER
EEFUD0G121XE
EEFUD0G151ER
EEFUD0G151XE
EEFUD0G151LE
EEFUD0G181ER
EEFUD0G181LE
EEFUD0J101ER
EEFUD0J101XE
EEFUD0J121ER
EEFUD0J121XE
EEFUD0J121LR
EEFUD0J151ER
EEFUD0J151LR
EEFUD0K680ER
EEFUD0K101ER
EEFUE0D271ER
EEFUE0D271XE
EEFUE0D331ER
EEFUE0D331XE
EEFUE0D391ER
EEFUE0D391XE
EEFUE0D391LE
EEFUE0D471ER
EEFUE0D471XE
EEFUE0D471LE
EEFUE0D561ER
EEFUE0D561LE
EEFUE0E221ER
EEFUE0E221XE
EEFUE0E271ER
EEFUE0E271XE
EEFUE0E331ER
EEFUE0E331XE
EEFUE0E331LE
EEFUE0E391ER
EEFUE0E391LE
EEFUE0E471ER
EEFUE0E471LE
EEFUE0G181ER
EEFUE0G181XE
EEFUE0G221ER
EEFUE0G221XE
EEFUE0G221LE
EEFUE0G271ER
EEFUE0G271LE
EEFUE0G331ER
EEFUE0J151ER
EEFUE0J151XE
EEFUE0J181ER
EEFUE0J181XE
EEFUE0J181LR
EEFUE0J221ER
EEFUE0J221LR
EEFUE0K101ER
EEFUE0K151ER
✽4
240 °C
260 °C
—
—
—
—
—
—
—
—
—
—
—
◯
—
◯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
◯
—
◯
—
—
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
—
◯
—
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
—
◯
—
◯
◯
<260 °C>
Min.
Packaging
Q’ty
(pcs)
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
✽1: Ripple current (100 kHz/ +20 to +105 °C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact Panasonic for details of allowable 240 °C reflow condition.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02 Mar. 2015
– EEF-18 –
SP-Cap/ Conductive Polymer Aluminum Capacitors (Specialty Polymer Aluminum Capacitors)
Surface Mount Type
Series:
SL
Old series
■ Features
●
●
●
●
Low-ESR (9 mΩ)
Excellent Noise-absorbent Characteristics
High Ripple Current
RoHS directive compliant
[Our Requests]
Since this series is old, we don't recommend you to adopt it
but SX series for your new design.
■ Specifications
Series & Size Code
Category Temp. Range
Rated Voltage Range
Nominal Cap.Range
Capacitance Tolerance
SL
–40 °C to +105 °C
2 V.DC to 6.3 V.DC
56 μF to 220 μF
±20 %
Reflow 240 °C : I < 0.04 CV (μA) 2 minutes (6.3 V.DC)
DC Leakage Current
Reflow 260 °C : I < 0.1 CV (μA) 2 minutes
< 0.06 (120 Hz/+20 °C)
Rated Voltage × 1.25 (15 °C to 35 °C)
After applying rated voltage for 1000 hours at 105 °C±2 °C, and then being stabilized at +20 °C,
capacitor shall meet the following limits.
Capacitance change
±10% of initial measured value
tan d
< Initial specified value
DC leakage current
< Initial specified value
After storing for 500 hours at 60 °C, 90 %
2, 2.5 V.DC
4 V.DC
6.3 V.DC
Capacitance change of
initial measurd value
+70, –20 %
+60, –20 %
+50, –20 %
tan d
< 200 % of initial specified value
DC leakage current
< Initial specified value
tan d
Surge Voltage
Endurance
Moisture resistance
■ Marking
■ Dimensions in mm(not to scale)
(Unit : mm)
+
H
–
P
P
L
Lot No.
Series &
Size Code
SL
R.V. code
W1
W2
Polarity bar (Positive)
W2
Cap.
L±0.2 W1±0.2 W2±0.1
7.3
4.3
2.4
H
P±0.3
1.8±0.1
1.3
✽ Externals of figure are the reference.
■ Low ESR Products
Rated CapaciSeries & Voltage
tance
Size Code (V.DC) (±20 %)
(μF)
2
SL
2.5
4
6.3
100
120
150
180
220
100
120
150
82
56
Reflow ✽3
Case Size
Specification
L
(mm)
W
(mm)
H
(mm)
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
✽1
✽2
Ripple ESR
current
(Ar.m.s.) (mΩ max.)
3.0
9
3.0
9
3.0
9
3.0
9
3.0
9
3.0
9
3.0
9
3.0
9
3.0
9
3.0
9
<260 °C>
Reflow
Part number
EEFSL0D101ER
EEFSL0D121ER
EEFSL0D151ER
EEFSL0D181ER
EEFSL0D221ER
EEFSL0E101ER
EEFSL0E121ER
EEFSL0E151ER
EEFSL0G820ER
EEFSL0J560R
Min.
Packaging
Q’ty
240 °C 260 °C
(pcs)
✽4
—
—
—
—
—
—
—
—
—
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
—
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
✽1: Ripple current (100 kHz/ +20 to +105 °C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
✽4: Please contact Panasonic for details of allowable 240 °C reflow condition.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03 Mar. 2015
– EEF-19 –
SP-Cap/ Conductive Polymer Aluminum Capacitors (Specialty Polymer Aluminum Capacitors)
Surface Mount Type
Series:
MC
Old series
■ Features
● Achieved 40 % miniaturization on together with
low ESR of SP-Cap for further design flexibility.
● RoHS directive compliant
[Our Requests]
Since this series is old, we don't recommend you to adopt it
■ Specifications
Category Temp. Range
Rated Voltage Range
Nominal Cap.Range
Capacitance Tolerance
DC Leakage Current
tan d
Surge Voltage
–40 °C to +105 °C
2 V.DC to 6.3 V.DC
47 μF to 120 μF
±20 % (120 Hz/+20 °C)
I < 0.1 CV (μA) 2 minutes
< 0.06 (120 Hz/+20 °C)
Rated Voltage × 1.25 (15 °C to 35 °C)
After applying rated voltage for 1000 hours at 105 °C±2 °C and then being atabilized at +20 °C,
Capacitor shall
Capacitance change
±10% of initial measured value
tan d
< Initial specified value
DC leakage current
< Initial specified value
After storing for 500 hours at 60 °C, 90 %
Endurance
Capacitance change
of initial measurd value
Moisture resistance
tan d
DC leakage current
2, 2.5 V.DC
4 V.DC
6.3 V.DC
+70, –20 %
+60, –20 %
+50, –20 %
< 200 % of initial specified value
< Initial specified value
■ Marking
■ Dimensions in mm(not to scale)
(Unit : mm)
–
H
+
P
W1
W2
L
Lot No.
R.V. code
W2
P
Polarity bar (Positive)
Cap.
L±0.2
W1±0.2
W2±0.1
H±0.2
P±0.3
6.0
3.2
1.8
1..9
1.3
✽ Externals of figure are the reference.
■ Standard Products
Rated
Series &
Voltage
Size Code
(V.DC)
MC
2
2.5
4
6.3
Reflow ✽3
Capacitance
(±20 %)
(μF)
120
100
82
47
Case Size
Specification
✽1
L
(mm)
W
(mm)
H
(mm)
6.0
6.0
6.0
6.0
3.2
3.2
3.2
3.2
1.9
1.9
1.9
1.9
✽2
Ripple
ESR
current
(Ar.m.s.) (mΩ max.)
2.7
12
2.7
12
2.2
18
2.2
18
<260 °C>
Part number
Min.
Packaging
Q’ty
(pcs)
EEFMC0D121R
EEFMC0E101R
EEFMC0G820R
EEFMC0J470R
3000
3000
3000
3000
✽1: Ripple current (100 kHz/ +20 to +105 °C ), ✽2: ESR (100 kHz/+20 °C)
✽3: Please refer to the page of “Mounting Specifications”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02 Mar. 2015
– EEF-20 –
CAUTION AND WARNING
1. The electronic components contained in this catalog are designed and produced for use in home electric appliances, office eq uipment, information equipment,
communications equipment, and other general purpose electronic devices.
Before use of any of these components for equipment that requires a high degree of safety, such as medical instruments, aeros pace equipment, disaster-prevention
equipment, security equipment, vehicles (automobile, train, vessel),
please be sure to contact our sales representative.
2. When applying one of these components for equipment requiring a high degree of safety, no matter what sort of application it might be, be sure to install a protective
circuit or redundancy arrangement to enhance the safety of your equipment. In addition, please carry out the safety test on your own responsibility.
3. When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on thespecifications with us in advance.
4. Technical information contained in this catalog is intended to convey examples of typical performances and/or applications a nd is not intended to make any
warranty with respect to the intellectual property rights or any other related rights of our company or any third parties nor grant any license under such rights.
5. In order to export products in this catalog, the exporter may be subject to the export license requirement under the Foreign Exchange and Foreign Trade Law of
Japan.
6. No ozone-depleting substances (ODSs) under the Montreal Protocol are used in the manufacturing processes of Automotive & Ind ustrial Systems Company, Panasonic
Corporation.
Please contact
Factory
The information in this catalog is valid as of December 2015.
Similar pages