Conductive Polymer Aluminum Solid Capacitors (OS-CON)[pdf :1.4 MB]

2016
Products Catalog
Conductive Polymer Aluminum Solid Capacitors
2016.06
http://industrial.panasonic.com/ww/products/capacitors/polymer-capacitors/os-con
——— Notices ———
■ Applicable Laws and Regulations
● This product complies with the RoHS Directive (Restriction of the use of certain Hazardous substances in
electrical and electronic equipment (DIRECTIVE 2011/65/EU).
● No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in
producing this product.
● We do not PBBs or PBDEs as brominated flame retardants.
● Export procedure which followed export related regulations, such as foreign exchange and a foreign trade
method, on the occasion of export of this product Thank you for your consideration.
■ Limited applications
● This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home
appliances, computers and other office equipment, optical equipment, measuring equipment.
● High reliability and safety are required [ be / a possibility that incorrect operation of this product may do harm
to a human life or property ] more. When use is considered by the use, the delivery specifications which suited
the use separately need to be exchanged.
——— Items to be observed ———
● This specification guarantees the quality and performance of the product as individual components.
Before use, check and evaluate their compatibility with installed in your products.
● Do not use the products beyond the specifications described in this document.
■ For specifications
● Install the following systems for a failsafe design to ensure safety if these products are to be used in
equipment where a defect in these products may cause the loss of human life or other signification damage,
such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment,
electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime
prevention equipment.
· The system is equipped with a protection circuit and protection device.
· The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event of
a single fault.
■ Conditions of use
● Before using the products, carefully check the effects on their quality and performance, and determined
whether or not they can be used. These products are designed and manufactured for general-purpose and
standard use in general electronic equipment. These products are not intended for use in the following special
conditions.
(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent.
(2) In direct sunlight, outdoors, or in dust.
(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a
high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NOx.
(4) In an environment where strong static electricity or electromagnetic waves exist.
(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near
these products.
(6) Sealing or coating of these products or a printed circuit board on which these products are mounted,
with resin and other material.
(7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular,
when using water or a water-soluble cleaning agent, be careful not to leave water residues)
(8) Using in the atmosphere which strays Acid or alkaline.
(9) Using in the atmosphere which there are excessive vibration and shock.
● Please arrange circuit design for preventing impulse or transitional voltage.
Do not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage,
instantaneous high voltage, high pulse voltage etc.
● Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid
deterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and
affects performance, characteristics, and functions of customer system.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Guidelines and precautions (OS-CON)
1. Circuit design
1.1 Prohibited circuits
(a) Leakage current of the OS-CON may increase in the following conditions.
(1) Soldering
(2) When voltage is not applied : high temperature no-load test, high temperature and high humiditynoload test, rapidly changing temperature test, etc.
(b) Avoid the use of the OS-CON in the following type of circuits because leakage current may increase.
(1) High-impedance circuits
(2) Coupling circuits
(3) Time constant circuits
(4) Other circuits that are significantly affected by leakage current
✽ If you plan to use 2 or more OS-CONs in a series connection, please contact us before use
1.2 Failure and life-span
The failure rate is 0.5 % /1000 h (Confidence level : 60 %) based on JIS C 5003.
The prospective failure is not zero. The mainly failure modes are as follows.
1.2-1 Contingency failure
The most common failure mode is a short circuit. Mainly caused by the soldering or operating temperature
environment, along with heat stresses, electrical stresses or mechanical stressesas follows.
(1) Applying voltage over the rated voltage.
(2) Applying reverse voltage
(3) Excessive mechanical stress
(4) Applying rush current by sudden charge or discharge out of the specification.
(a) The following phenomenon is seen when short-current is applied to the OS-CON.
(1) When current is relatively low (f10 : approx 1 A or less, f8 : approx 0.5 A or less, f6.3 : approx 0.2 A or
less) The OS-CON becomes heated, but no effects are visible even when the current is continously carried.
(2) When the short circuit currents exceed the mentioned value above.
After internal temperature increase, sealing rubber may be turned over.
In some cases, odorous gas may be produced.
(b) In case a short circuit occurs, ensure safety by fully considering the followings.
(1) If odorous gas is released, turn off the main power of the equipment.
In this case, keep your face and hands away from the area.
(2) Though it depends on the conditions, it takes seconds to minutes before odorant gas generates.
Protective circuit should operate in this period.
(3) If the gas comes into eyes, rinse immediately. If the gas is inhaled, gargle immediately.
(4) Do not lick the electrolyte. If the electrolyte touches skin, wash it off with soap immediately.
(5) The OS-CON contains combustible substances. In case a large current continues to flow after a
short circuit, in the worst case, the shorted-out section may ignite. For safety, install a redundant
circuit or a protective circuit, etc.
1.2-2 Wear-out failure (life time)
When lifetime span exceeded the specified guarantee time of endurance and damp heat, electrolyte
might insulate and cause electric characteristic changed. This is called an open circuit.
The electric characteristics of capacitance and ESR may possibly change within the specified range
in specifications even if it is used under the condition of the rated voltage, electric and mechanical
performance. Please note it when designing.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
1.3 Leakage current
Mechanical stress may cause OS-CON’s leakage current increased.
In such a case, leakage current will gradually decrease by applying voltage (withinthe category voltage and
the upper limit of category temperature).
Then, self-healing speed of leakage current is faster when it is near to the upper limit of category temperature
and the category voltage.
OS-CON
leakage current restoration characteristics
16 V.DC/10 μF (16 V.DC applied)
OS-CON
leakage current restoration characteristics
10 V.DC/33 μF (Ambient temperature : 65 °C)
(Measured voltage : 10 V)
1000
Leakage current (μA)
Leakage current (μA)
1000
100
10
60 °C 20 °C
1
100
5 V applied
10
8 V applied
1
10 V applied
105 °C
0.1
1
10
Time (h)
100
1000
0.1
1
10
Time (h)
100
1000
✽ To make the recovery of LC values easy to show, samples that LC values have
been increased on purpose are used in the test.
1.4 Rapid charge and discharge limitation
Allowance of a large rush current to flow due to rapid charge and discharge may result in short circuit or
large leakage current. The protection circuit, to maintain high reliability, is recommended when rush current to
flow to the OS-CON is in the following cases.
(a) Products which 10 times of allowable ripple current is less than 10 A : It is when 10 A or over of rush
current is applied.
(b) Products which 10 times of allowable ripple current is 10 A or over : It is when rush current, which the
figure is over 10 times of allowable ripple current, is applied.
2. Mounting
2.1 Soldering with a soldering iron
(a) When lead terminals for radial lead type must be processed because the lead pitch and the PCB holes
do not match, process them without any stresses to the OS-CON before soldering.
(b) Solder without any excessive stresses to the OS-CON itself.
(c) When the OS-CON has been soldered once and needs to be removed, remove it after the solder has
been completely melted.
(d) Do not let the tip of the soldering iron touch the OS-CON itself.
2.2 Flow soldering
(a)
(b)
(c)
(d)
(e)
Do not apply flow soldering to OS-CON SMD type.
Do not solder the OS-CON itself by submerging it in melted solder.
Solder the opposite side that the OS-CON is mounted on.
Note that flux does not adhere to anywhere expect the lead terminal.
Note that other components do not fall over and touch the OS-CON when soldering.
2.3 Reflow soldering
(a) Do not apply reflow soldering to OS-CON Radial Lead type.
(b) Please contact us for setting VPS conditions.
2.4 Capacitor handling after soldering
Do
(a)
(b)
(c)
(d)
not subject the OS-CON to excessive stress as follows.
Do not tilt, bend or twist the OS-CON.
Do not move the PCB with holding the OS-CON itself.
Do not hit the OS-CON with objects.
When stacking PCBs, make sure that the OS-CON does not touch other PCBs or components.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
2.5 Circuit board cleaning
Check the following items before washing PC board with these detergents: high quality alcohol-based
cleaning fluid such as Pine-a ST-100S, clean thru 750H, 750L, 710M, 750K or Techno Care FRW 14 through
17 or detergents including substitute freon as AK-225AES or IPA.
(a) Use immersion or ultrasonic waves to clean within 2 minutes.
(b) The temperature of the cleaning fluid should be less than 60 °C.
(c) Watch the contamination of the detergent such as conductivity, pH, specific gravity, water content, etc.
(d) Do not store the OS-CON in a location subject to gases from the cleaning fluid or in an airtight container
after cleaning.
(e) Dry the PCB or OS-CON with hot air that should be less than the upper category temperature.
(f) Please note that indication may disappear when rubbing print side after washing depending on a cleaner.
(g) Please contact us for details about detergents, cleaning methods and detergents other than those listed
above.
2.6 Fixatives and coating materials
(a) Select the appropriate covering and sealant materials for the OS-CON. In particular, don’t use acetone in
the fixative, coating agent and diluent.
(b) Before applying the fixative or coating, completely remove any flux residue and foreign matter from the
area where the board and the OS-CON will be jointed together.
(c) Allow any detergent to dry before applying the fixative or coating.
(d) Please contact us for the fixative and coating heat curing conditions.
2.7 Capacitor insulation
Be sure to completely separate the case, negative lead terminal, positive lead terminal and PC board patterns
with each other due to the following reasons.
(a) Insulation is not guaranteed at a part of resin on the surface of a case.
(b) It offers inconstant resistance between a case and a negative lead terminal and it isn’t insulated.
3. Storage
Open the bags just before mounting and use up all products once opened,
For keeping a good solderability, store the OS-CON as follows.
✽ Due to the feature of the plating material of the lead terminal, it may rarely become dull color during the
specified period as follow, but it will not affect the solderability.
Before unsealing
SMD type
✽1
Bag packing product
Radial
lead type Taping product
Within 24 months after shipment
Within 30 months after shipment
Within 24 months after shipment
After unsealing
Within 30 days from opening
(packaged with carrier tape)
Within 7 days from opening
✽1 The JEDEC J-STD-020 standard is not applicable
◇ Intellectual property right
We, Panasonic Group are providing the product and service that customers can use without anxiety, and are
working positively on the protection of our products underintellectual property rights.
Representative patents relating to OS-CON are as follows:
US Patent Nos. 6310765, 6508846 and 7158367
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Line up
A5
B6
SVPS
Long life
SVPB
Low profile
C6
C5
C55
B6
SVPA
Low ESR
High ripple
SVQP
Guaranteed at 125℃
C6
C6
Conductive Polymer Aluminum Solid Capacitors
Line up
A5
B6
C6
SVP
Standard
B9
C6
SEPC
Super low ESR
Large capacitance
Small size
Low profile
105℃5,000h
C9
C6
SEQP
105℃5,000h
Guaranteed at 125℃
Rated 32V max.
C6
SEP
Standard
Conductive Polymer Aluminum Solid Capacitors
Diagram
SVP
Standard
F12
Low ESR
High ripple
F8 Size
4.0 to 20 V.DC
56 to 680 μF
E7 Size
4.0 to 20 V.DC
33 to 330 μF
F8 Size
E7 Size
2.5 to 16 V.DC
180 to 820 μF
4.0 to 16 V.DC
100 to 680 μF
6.3 to 20 V.DC
47 to 220 μF
E7 Size
E7 Size
C6 Size
2.5 to 20 V.DC
47 to 330 μF
4.0 to 25 V.DC
10 to 270 μF
4.0 to 20 V.DC
22 to 150 μF
C6 Size
C6 Size
2.5 to 20 V.DC
22 to 180 μF
4.0 to 20 V.DC
22 to 150 μF
B6 Size
B6
2.5 to 20 V.DC
10 to 82 μF
4.0 to 16 V.DC
22 to 68 μF
Size
Size
A5 Size
2.5 to 20 V.DC
22 to 220 μF
B6
SVQP
Guaranteed at 125℃
F8 Size
Size
2.5 to 20 V.DC
100 to 680 μF
C6
Long life
Size
2.5 to 20 V.DC
150 to 1,500 μF
E12
SVPS
SVPA
Size
4.0 to 20 V.DC
10 to 68 μF
A5 Size
4.0 to 16 V.DC
3.3 to 33 μF
4.0 to 10 V.DC
10 to 33 μF
SVPB
Low profile
C55 Size
20 V.DC
22 μF
C5 Size
2.5 to 20 V.DC
15 to 120 μF
SEP
Standard
E12 Size
2.5 to 20 V.DC
100 to 680 μF
E7 Size
4.0 to 20 V.DC
33 to 330 μF
F13 Size
2.5 to 20 V.DC
150 to 1,500 μF
F8 Size
4.0 to 20 V.DC
56 to 680 μF
C6
Size
4.0 to 20 V.DC
22 to 150 μF
SEPC
105℃ 5,000h
Super low ESR
Large capacitance
F13 Size
2.5 to 16 V.DC
470 to 2,700 μF
SEQP
F13 Size
105℃ 5,000h
4.0 to 20 V.DC
High voltage
150 to 1,200 μF
Guaranteed at 125℃
E13 Size
E12 Size
E12 Size
F8 Size
2.5 to 6.3 V.DC
470 to 820 μF
16 V.DC
180, 270 μF
4.0 to 32 V.DC
18 to 560 μF
4.0 to 32 V.DC
15 to 680 μF
E9 Size
E7 Size
E7 Size
C6 Size
2.5 to 16 V.DC
180 to 1,000 μF
6.3 to 16 V.DC
150 to 1,000 μF
4.0 to 32 V.DC
6.8 to 330 μF
4.0 to 20 V.DC
22 to 150 μF
C9 Size
C6 Size
2.5 to 16 V.DC
100 to 820 μF
2.5, 16 V.DC
100 to 560 μF
C55 Size B9 Size
6.3 V.DC
220 μF
2.5 V.DC
100 to 560 μF
Conductive Polymer Aluminum Solid Capacitors
Mounting specifications
● Recommendable
reflow soldering
Temperature on the
surface of capacitor
<Peak temperature 250 °C lead free reflow soldering profile>
250 °C
230 °C
220 °C
200 °C
180 °C
40 s max
50 s max
150 °C
120 s max
60 s max
Time (sec.)
Reflow cycle : 2 max.
Temperature on the
surface of capacitor
<Peak temperature 260 °C lead free reflow soldering profile>
260 °C
230 °C
220 °C
200 °C
180 °C
40 s max
50 s max
150 °C
120 s max
60 s max
Time (sec.)
Reflow cycle : 1 max.
<Soldering with a soldering iron>
Tip of a soldering iron : 400±10 °C
Working time : 5 sec. max
<Flow soldering>
Temperature
120 °C or less
(ambient temperature)
Preheating
Soldering
condition
260 °C+5 °C or less
Time
Flow number
120 sec. or less
1 time
10+1 sec. or less
2 times or less
✽1
✽1 When soldering 2 times, total immersion time should be 10+1 sec. or less.
● Land
pattern
c
Unit : mm
a
b
Size code
A5
B45
B6
C5
C55
C6
C10
E7
E12
F8
F12
a
1.0
1.4
1.4
2.1
2.1
2.1
2.1
2.8
2.8
4.3
4.3
b
6.2
7.4
7.4
9.1
9.1
9.1
9.1
11.1
11.1
13.1
13.1
c
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.9
1.9
1.9
1.9
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Explanation of part numbers
Part number system
・Surface mount type
SVPK
・Radial lead type
Conductive Polymer Aluminum Solid Capacitors
Packing specifications
● SMD
type (Taping)
<Carrier tape>
4.0±0.1
2.0±0.1
+0.1
f1.5−0
E
t
W
F
(Polarity)
B
(−)
(+)
Mounting
parts
T
Direction of unreeling
A
P
Unit : mm
Dimension
Size code
A5
B45
B6
C5
C55
C6
C10
E7
E12
F8
F12
A±0.2
B±0.2
W±0.3
F±0.1
E±0.1
P±0.1
t±0.1
T±0.2
4.7
5.6
5.6
6.9
6.9
6.9
7.0
8.6
8.6
10.7
10.7
4.7
5.6
5.6
6.9
6.9
6.9
7.0
8.6
8.6
10.7
10.7
12.0
16.0
16.0
16.0
16.0
16.0
24.0
24.0
24.0
24.0
24.0
5.5
7.5
7.5
7.5
7.5
7.5
11.5
11.5
11.5
11.5
11.5
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
8.0
8.0
8.0
12.0
12.0
12.0
16.0
12.0
16.0
16.0
16.0
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.4
0.5
0.4
0.4
5.8
4.8
6.2
5.3
6.2
6.2
10.5
7.2
12.3
8.2
13.0
● Minimum
packing quantity and weight
<Reel>
Direction of unreeling
W2
W1
2.0±0.5
f80.0±1.0
f13.0±0.2
f21.0±0.8
R1.0
W1
W2
f380±2.0
Size code
A5
B45
B6
C5
C55
C6
C10
E7
E12
F8
F12
Quantity (pcs./Reel, f380) Typical weight (g)
2000
700
2500
900
1500
800
1300
800
1000
800
1000
800
500
700
1000
1100
400
800
500
1000
400
1000
Unit : mm
Size code
A5, B45
B6, C5, C55, C6
C10, E7, F8, E12, F12
W1±0.5
13.0
17.0
25.0
W2±1.0
17.5
21.5
29.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
● Radial
lead type
<Applicationsl>
✽ The following table is a standard specification. Please contact us separately concerming specifications except
for that mentioned below. Because of a limit on the length of a model name, the part of process name
changes to +S from +TSS, +D from +TS, +3 from +C3, Please contact us for details.
Series
Size code
SEP, SEQP
SEPC, SEPF
SXE
B9, C55, C6, C9, E7, E9, E12
E13
F8, F13
Bag-packed product (lead terminal cutting)
Not processed
Straight cut
◯
+C3
◯
+C3
◯
+C3
Taping
+TSS (+S)
+TS (+D)
+T
<Lead terminal cutting>
Lead terminal cutting code Process names
Size code (fD)
Dimensions
+C3
(+3)
Straight
cut
B9 (f5)
C55, C6, C9 (f6.3)
E7, E9, E12, E13 (f8)
F8, F13 (f10)
F±1.0
Unit : mm
C3
3.5
L
L±0.5
Size code
F
B9
2.0
Unit : mm
C55, C6, C9 E7, E9, E12, E13
2.5
3.5
F8, F13
5.0
<Lead terminal taping>
Size code (fD)
Taping
P2
H
W1
W2
P1
F
P0
P2
W0
F8, F13 (f10)
L
F=5.0 mm
k
+T
Δh
P
fD0
W
F
Hold-down
tape
t
Taping code
Carrier
tape
Δh
P2
t
Hold-down
tape
Carrier
tape
Δh
fD0
P0
W
H
W1
W0 W2
F
t
P1
k
B9 (f5)
C55, C6, C9 (f6.3)
E7, E9, E12 (f8)
fD0
P
L
F=2.0 mm
F=2.5 mm
F=3.5 mm
+TSS
(+S)
W0
F
P0
W
P1
E13 (f8)
k
F=3.5 mm
L
+TS
(+D)
W1
W2
H
P
Hold-down
tape
Carrier
tape
Unit : mm
+0.8
−0.2
Code
F
5.0
+T
f10
3.5
+TS (+D) f8
2.0
f5
+TSS
f6.3 2.5
(+S)
3.5
f8
P±1.0
12.7
12.7
12.7
12.7
12.7
P0±0.2
12.7
12.7
12.7
12.7
12.7
P1±0.5
3.85
4.60
5.35
5.10
4.60
P2±1.0 Δh±1.0 W±0.5 W0 (min.) W1±0.5 W2 (max.)
6.35
0
18.0 9.5
9.0
2.5
6.35
0
18.0 9.5
9.0
2.5
6.35
0
18.0 9.5
9.0
2.5
6.35
0
18.0 9.5
9.0
2.5
6.35
0
18.0 9.5
9.0
2.5
H±0.75 fD0±0.2 t±0.3 k (max.)
18.5 4.0
0.6
0
17.5 4.0
0.6
0
17.5 4.0
0.6
0
17.5 4.0
0.6
0
17.5 4.0
0.6
0
L (max.)
11.0
11.0
11.0
11.0
11.0
Minimum packing quantity and weight
Size
code
Case
size
B9
C55
C6
C9
E7
f5
f6.3
f6.3
f6.3
f8
Processed type discrete lead terminals Zig-zag pack taping type
Quantity Typical weight Quantity Typical weight
(pcs./Bag)
(g)
(pcs./Bag)
(g)
500
180
2000
1000
500
150
1500
650
500
160
1500
700
500
240
1500
1000
200
110
1000
820
Size
code
Case
size
E9
E12
E13
F8
F13
f8
f8
f8
f10
f10
Processed type discrete lead terminals Zig-zag pack taping type
Quantity Typical weight Quantity Typical weight
(pcs./Bag)
(g)
(pcs./Bag)
(g)
200
130
1000
900
200
200
1000
980
200
160
1000
1060
200
180
500
890
200
280
500
940
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
NEW
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SXV
Features
● Super
● RoHS
high voltage (100 V.DC max.)
compliance, Halogen free
Specifications
Size code
Category temperature range
Rated voltage range
Rated capacitance range
Capacitance tolerance
Leakage current
Dissipation factor (tan d)
Endurance
Damp heat
(Steady State)
E12
–55 °C to +105 °C
63 V.DC to 100 V.DC
15 µF to 33 µF
±20 % (120 Hz / + 20 °C)
Please see the attached characteristics list
Please see the attached characteristics list
+105 °C, 5000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
Dimensions (not to scale)
0.2 max.
W
–
C
H
fD
P
Polarity marking (−)
Lot. No.
Series
+
L
R
R. Capacitance
Unit : mm
R. Voltage
Size
code
fD±0.5
E12
8.0
L
+0.1
−0.4
11.9
W±0.2 H±0.2 C±0.2
8.3
8.3
9.0
R
P±0.2
0.8 to 1.1
3.2
✽ Externals of figure are the reference.
Characteristics list
Rated
Rated
Series voltage capacitance
(V.DC)
(µF)
SXV
63
100
33
15
Case size (mm)
fD
L
8.0
8.0
11.9
11.9
Size
code
E12
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
2950
25
0.12
2350
40
0.12
LC ✽4
(µA)
104
75
Standard (Reel size : f380)
Min.
Packaging Q'ty
Part number
(pcs)
63SXV33M
400
100SXV15M
400
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
120 Hz < f < 1 kHz
1 kHz < f < 10 kHz
10 kHz < f < 100 kHz
100 kHz < f < 500 kHz
Coefficient
0.05
0.3
0.7
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVPG
Features
● Low
profile (Height 4.5 mm max.)
ESR (8 mΩ to 30 mΩ)
● RoHS compliance, Halogen free
● Low
Specifications
Size code
Category temperature range
Rated voltage range
Rated capacitance range
Capacitance tolerance
Leakage current
Dissipation factor (tan d)
Endurance
Damp heat
(Steady State)
B45
C10
–55 °C to +105 °C
16 V.DC to 25 V.DC
15 µF to 47 µF
16 V.DC
270 µF
±20 % (120 Hz / + 20 °C)
Please see the attached characteristics list
Please see the attached characteristics list
+105 °C, 5000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
Dimensions (not to scale)
0.2 max.
W
–
Series
+
L
R. Capacitance
R. Voltage
Size
code
fD±0.5
B45
C10
5.0
6.3
C
H
fD
P
Polarity marking (−)
Lot. No.
L
+0.1
−0.4
R
W±0.2 H±0.2 C±0.2
4.4
9.9
5.3
6.6
5.3
6.6
6.0
7.3
Unit : mm
R
P±0.2
0.6 to 0.8
0.6 to 0.8
1.4
2.1
✽ Externals of figure are the reference.
Characteristics list
Rated
Rated
Series voltage capacitance
(V.DC)
(µF)
16
SVPG
20
25
47
270
33
15
Case size (mm)
fD
L
5.0
6.3
5.0
5.0
4.4
9.9
4.4
4.4
Specifications
Size
code
B45
C10
B45
✽1
Ripple
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
3200
25
0.12
5800
8
0.12
3000
27
0.12
2800
30
0.12
LC ✽4
(µA)
150
864
132
75
Standard (Reel size : f380)
Min.
Packaging Q'ty
Part number
(pcs)
16SVPG47M
2500
16SVPG270M
500
20SVPG33M
2500
25SVPG15M
2500
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVPF
Features
● High
voltage (50 V.DC max.)
capacitance (1000 μF max.)
● 105 °C 5000 h
● RoHS compliance, Halogen free
● Large
Specifications
Size code
B6
C6
E7
E12
Category temperature range
–55 °C to +105 °C
Rated voltage range
16 V.DC to 25 V.DC
16 V.DC to 50 V.DC
Rated capacitance range 27 μF to 82 μF
10 μF to 180 μF
18 μF to 270 μF
39 μF to 560 μF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+105 °C, 5000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
F12
68 μF to 1000 μF
Dimensions (not to scale)
0.2 max.
W
C
H
fD
P
–
Polarity marking (−)
Lot. No.
+
L
R
Unit : mm
Series
R. Capacitance
R. Voltage
Size
code
fD±0.5
B6
C6
E7
E12
F12
5.0
6.3
8.0
8.0
10.0
L
+0.1
−0.4
5.9
5.9
6.9
11.9
12.6
W±0.2 H±0.2 C±0.2
5.3
6.6
8.3
8.3
10.3
5.3
6.6
8.3
8.3
10.3
6.0
7.3
9.0
9.0
11.0
R
P±0.2
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.8 to 1.1
0.8 to 1.1
1.4
2.1
3.2
3.2
4.6
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Characteristics list
Rated
Rated
Series voltage capacitance
(V.DC)
(μF)
16
20
SVPF
25
35
50
82
180
270
560
1000
56
120
180
390
560
27
47
56
82
100
180
330
22
39
82
120
10
18
39
68
Case size (mm)
fD
L
5.0
6.3
8.0
8.0
10.0
5.0
6.3
8.0
8.0
10.0
5.0
6.3
6.3
8.0
8.0
8.0
10.0
6.3
8.0
8.0
10.0
6.3
8.0
8.0
10.0
5.9
5.9
6.9
11.9
12.6
5.9
5.9
6.9
11.9
12.6
5.9
5.9
5.9
6.9
6.9
11.9
12.6
5.9
6.9
11.9
12.6
5.9
6.9
11.9
12.6
Size
code
B6
C6
E7
E12
F12
B6
C6
E7
E12
F12
B6
C6
E7
E12
F12
C6
E7
E12
F12
C6
E7
E12
F12
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
3000
27
0.12
3300
22
0.12
3300
22
0.12
4950
14
0.12
5400
12
0.12
2800
30
0.12
3200
25
0.12
3200
25
0.12
4950
14
0.12
5400
12
0.12
2450
40
0.12
2800
30
0.12
2800
30
0.12
3000
28
0.12
3200
24
0.12
4650
16
0.12
5000
14
0.12
2600
35
0.12
2800
30
0.12
4000
20
0.12
4400
18
0.12
2500
40
0.12
2700
35
0.12
3800
25
0.12
4300
20
0.12
LC ✽4
(μA)
262
576
864
1792
3200
224
480
720
1560
2240
135
235
280
410
500
900
1650
154
273
574
840
100
180
390
680
Standard (Reel size : f380)
Min.
Packaging Q'ty
Part number
(pcs)
16SVPF82M
1500
16SVPF180M
1000
16SVPF270M
1000
16SVPF560M
400
16SVPF1000M
400
20SVPF56MX
1500
20SVPF120M
1000
20SVPF180M
1000
20SVPF390M
400
20SVPF560M
400
25SVPF27MX
1500
25SVPF47M
1000
25SVPF56M
1000
25SVPF82M
1000
25SVPF100M
1000
25SVPF180M
400
25SVPF330M
400
35SVPF22M
1000
35SVPF39M
1000
35SVPF82M
400
35SVPF120M
400
50SVPF10M
1000
50SVPF18M
1000
50SVPF39M
400
50SVPF68M
400
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
120 Hz < f < 1 kHz
1 kHz < f < 10 kHz
10 kHz < f < 100 kHz
100 kHz < f < 500 kHz
Coefficient
0.05
0.3
0.7
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVPE
Features
● Super
low ESR (8 mΩ to 18 mΩ)
capacitance (1200 μF max.)
● RoHS compliance, Halogen free
● Large
Specifications
Size code
B6
C6
C10
Category temperature range
–55 °C to +105 °C
Rated voltage range
2.5 V.DC to 6.3 V.DC
2.5 V.DC to 10 V.DC
2 V.DC to 16 V.DC
Rated capacitance range
150 μF to 390 μF
220 μF to 390 μF
180 μF to 1200 μF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+105 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
F12
16 V.DC
470 μF
Dimensions (not to scale)
0.2 max.
W
H
fD
Polarity marking (−)
Lot. No.
+
L
Series
Size
code
R. Capacitance
B6
C6
C10
F12
R. Voltage
fD±0.5
5.0
6.3
6.3
10.0
C
P
–
L
+0.1
−0.4
5.9
5.9
9.9
12.6
R
Unit : mm
W±0.2 H±0.2 C±0.2
R
P±0.2
5.3
5.3
6.0 0.6 to 0.8 1.4
6.6
6.6
7.3 0.6 to 0.8 2.1
6.6
6.6
7.3 0.6 to 0.8 2.1
10.3
10.3
11.0 0.8 to 1.1 4.6
✽ Externals of figure are the reference.
Characteristics list
Rated Rated
Series voltage capacitance
(V.DC) (μF)
2
2.5
1200
270
330
390
SVPE
6.3
150
180
220
10
16
220
180
470
Case size (mm)
fD
L
6.3
5.0
5.0
5.0
5.0
6.3
5.0
5.0
5.0
6.3
6.3
6.3
10.0
9.9
5.9
5.9
5.9
5.9
5.9
5.9
5.9
5.9
5.9
5.9
9.9
12.6
Specifications
Size Ripple ✽1
ESR
code current 100 kHz/20 °C 300 kHz/20 °C tan d ✽2
(mAr.m.s.) (mΩ max.) (mΩ max.)
C10
5230
8
8
0.12
3860
10
9
0.12
3150
15
13
0.12
B6
3860
10
9
0.12
3860
10
9
0.12
C6
3900
10
9
0.12
3520
12
10
0.12
3150
15
13
0.12
B6
3150
15
13
0.12
3900
10
9
0.12
C6
2700
20
18
0.12
C10
4460
11
10
0.12
F12
6100
10
9
0.12
✽3
LC
(μA)
500
500
500
500
700
500
500
500
500
500
500
576
1504
Standard (Reel size : f380)
Min.
Packaging Q'ty
Part number
(pcs)
2SVPE1200M
500
2R5SVPE270M
1500
2R5SVPE330M
1500
2R5SVPE330MY
1500
2R5SVPE390MX
1500
2R5SVPE390M
1000
6SVPE150M
1500
6SVPE180M
1500
6SVPE220MW
1500
6SVPE220M
1000
10SVPE220M
1000
16SVPE180M
500
16SVPE470M
400
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 tan d (120 Hz/+20 °C) ✽3 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVPD
Features
● 125 °C 2000 h
● Guaranteed at 85 °C 85 %
● RoHS compliance, Halogen
free
Specifications
Size code
C6
E7
F8
E12
Category temperature range
–55 °C to +125 °C
Rated voltage range
10 V.DC to 25 V.DC 16 V.DC to 35 V.DC
25 V.DC to 35 V.DC
Rated capacitance range 10 µF to 56 µF
8.2 µF to 82 µF
18 µF to 39 µF
22 µF to 47 µF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+125 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
+85 °C, 85 % to 90 %, 1000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
F12
47 µF to 82 µF
Dimensions (not to scale)
0.2 max.
W
H
fD
Polarity marking (−)
Lot. No.
+
L
Series
Size
code
R. Capacitance
C6
E7
F8
E12
F12
R. Voltage
fD±0.5
6.3
8.0
10.0
8.0
10.0
C
P
–
L
+0.1
−0.4
5.9
6.9
7.9
11.9
12.6
R
Unit : mm
W±0.2 H±0.2 C±0.2
R
P±0.2
6.6
6.6
7.3 0.6 to 0.8 2.1
8.3
8.3
9.0 0.6 to 0.8 3.2
10.3
10.3
11.0 0.6 to 0.8 4.6
8.3
8.3
9.0 0.8 to 1.1 3.2
10.3
10.3
11.0 0.8 to 1.1 4.6
✽ Externals of figure are the reference.
Characteristics list
Rated Rated
Series voltage capacitance
(V.DC) (µF)
10
16
25
SVPD
35
56
82
10
22
39
47
82
8.2
18
22
47
Case size (mm)
fD
L
6.3
8.0
6.3
8.0
10.0
8.0
10.0
8.0
10.0
8.0
10.0
5.9
6.9
5.9
6.9
7.9
11.9
12.6
6.9
7.9
11.9
12.6
Specifications
Size Ripple ✽1 Allowable ✽1
✽2
code current ripple current ESR
tan d ✽3
(mΩ
max.)
(mAr.m.s.) (mAr.m.s.)
C6
538
1700
45
0.12
E7
670
2120
40
0.12
C6
474
1500
65
0.10
E7
580
1835
48
0.10
F8
664
2100
45
0.10
E12
943
2980
30
0.12
F12
1202
3800
28
0.12
E7
400
1300
70
0.10
F8
550
1800
60
0.10
E12
700
2300
50
0.12
F12
1150
3650
30
0.12
✽4
LC
(µA)
112
262
50
110
195
235
410
57
126
154
329
Standard (Reel size : f380)
Min.
Part number
Packaging Q'ty
(pcs)
10SVPD56M
1000
16SVPD82M
1000
25SVPD10M
1000
25SVPD22M
1000
25SVPD39M
500
25SVPD47M
400
25SVPD82M
400
35SVPD8R2M
1000
35SVPD18M
500
35SVPD22M
400
35SVPD47M
400
✽1 Ripple current (100 kHz/ +105 °C < Tx < 125 °C), Allowable ripple current (100 kHz / Tx < 105 °C)
✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVPC
Features
● Low
ESR (9 mΩ to 30 mΩ)
capacitance (2700 μF max.)
● RoHS compliance, Halogen free
● Large
Specifications
Size code
B6
C6
E7
E12
Category temperature range
–55 °C to +105 °C
Rated voltage range
2.5 V.DC to 16 V.DC
Rated capacitance range 39 μF to 180 μF
68 μF to 560 μF 120 μF to 680 μF 270 μF to 1500 μF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+105 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
F12
2.5 V.DC
2700 μF
Dimensions (not to scale)
0.2 max.
W
Polarity marking (−)
Lot. No.
C
H
fD
P
–
+
L
R
Series
R. Capacitance
R. Voltage
Unit : mm
Size
code
fD±0.5
B6
C6
E7
E12
F12
5.0
6.3
8.0
8.0
10.0
L
+0.1
−0.4
5.9
5.9
6.9
11.9
12.6
W±0.2 H±0.2 C±0.2
5.3
6.6
6.9
11.9
10.3
5.3
6.6
6.9
11.9
10.3
6.0
7.3
9.0
9.0
11.0
R
P±0.2
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.8 to 1.1
0.8 to 1.1
1.4
2.1
3.2
3.2
4.6
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Characteristics list
Rated Rated
Series voltage capacitance
(V.DC) (μF)
180
390
2.5
560
680
820
1500
2700
150
4.0
330
560
1200
1500
100
SVPC
120
6.3
220
330
390
820
68
10
120
270
330
39
68
16
100
120
150
270
Case size (mm)
fD
L
5.0
5.0
5.0
6.3
6.3
6.3
8.0
8.0
8.0
10.0
5.0
5.0
5.0
6.3
6.3
6.3
8.0
8.0
8.0
8.0
5.0
5.0
5.0
6.3
6.3
6.3
8.0
8.0
5.0
5.0
6.3
6.3
8.0
8.0
5.0
5.0
6.3
6.3
6.3
8.0
8.0
8.0
5.9
5.9
5.9
5.9
5.9
5.9
6.9
11.9
11.9
12.6
5.9
5.9
5.9
5.9
5.9
5.9
6.9
11.9
11.9
11.9
5.9
5.9
5.9
5.9
5.9
5.9
6.9
11.9
5.9
5.9
5.9
5.9
6.9
6.9
5.9
5.9
5.9
5.9
5.9
6.9
6.9
11.9
Specifications
Size Ripple ✽1
ESR
code current 100 kHz/20 °C 300 kHz/20 °C tan d ✽2
(mAr.m.s.) (mΩ max.) (mΩ max.)
1970
30
26
0.12
B6
2200
24
20
0.12
2800
19
16
0.12
2410
25
22
0.12
C6
3160
15
13
0.12
3500
16
14
0.12
E7
3370
20
17
0.12
5380
9
8
0.15
E12
5150
10
9
0.15
F12
5070
12
10
0.15
1970
30
26
0.12
B6
2240
23
20
0.12
2730
20
17
0.12
2320
27
23
0.12
C6
2630
21
18
0.12
3160
15
13
0.12
E7
3220
22
19
0.12
5380
9
8
0.15
E12
4700
12
10
0.15
4700
12
10
0.15
1970
21
18
0.12
B6
2150
30
26
0.12
2660
25
21
0.12
2320
27
23
0.12
C6
3160
15
13
0.12
3390
17
15
0.12
E7
3220
22
19
0.12
E12
4700
12
10
0.15
1970
30
26
0.12
B6
2540
23
20
0.12
2320
27
23
0.12
C6
2600
22
19
0.12
3220
22
19
0.12
E7
3460
19
17
0.12
1820
35
30
0.12
B6
2350
27
23
0.12
2200
30
26
0.12
C6
2440
25
22
0.12
2490
24
23
0.12
2900
27
23
0.12
E7
3220
22
21
0.12
E12
4070
16
14
0.15
LC ✽3
(μA)
300
300
300
300
300
300
500
500
750
1350
300
300
300
300
300
300
500
500
960
1200
300
300
300
300
300
415
491
1033
300
300
300
300
500
660
300
300
300
300
300
500
500
864
Standard (Reel size : f380)
Min.
Packaging Q'ty
Part number
(pcs)
2R5SVPC180M
1500
2R5SVPC180MY
1500
2R5SVPC180MV
1500
2R5SVPC390M
1000
2R5SVPC390MV 1000
2R5SVPC560M
1000
2R5SVPC680M
1000
2R5SVPC820M
400
2R5SVPC1500M
400
2R5SVPC2700M
400
4SVPC150M
1500
4SVPC150MY
1500
4SVPC150MV
1500
4SVPC330M
1000
4SVPC330MY
1000
4SVPC330MV
1000
4SVPC560M
1000
4SVPC560MX
400
4SVPC1200M
400
4SVPC1500M
400
6SVPC100M
1500
6SVPC100MY
1500
6SVPC120MV
1500
6SVPC220M
1000
6SVPC220MV
1000
6SVPC330M
1000
6SVPC390M
1000
6SVPC820M
400
10SVPC68M
1500
10SVPC68MV
1500
10SVPC120M
1000
10SVPC120MV
1000
10SVPC270M
1000
10SVPC330M
1000
16SVPC39M
1500
16SVPC39MV
1500
16SVPC68M
1000
16SVPC68MV
1000
16SVPC100M
1000
16SVPC120M
1000
16SVPC150M
1000
16SVPC270M
400
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 tan d (120 Hz/+20 °C) ✽3 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Jun. 2016
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVPA
Features
● Low
ESR (18 mΩ max.)
ripple (4240 mA.r.m.s.)
● RoHS compliance, Halogen free
● High
Specifications
Size code
Category temperature range
Rated voltage range
Rated capacitance range
Capacitance tolerance
Leakage current
Dissipation factor (tan d)
Endurance
Damp heat
(Steady State)
B6
C6
E7
F8
–55 °C to +105 °C
2.5 V.DC to 20 V.DC
10 µF to 82 µF
22 µF to 180 µF
47 µF to 330 µF
±20 % (120 Hz / + 20 °C)
Please see the attached characteristics list
Please see the attached characteristics list
+105 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
2.5 V.DC to 16 V.DC
180 µF to 820 µF
Dimensions (not to scale)
0.2 max.
W
Polarity marking (−)
Lot. No.
C
H
fD
P
–
+
L
R
Series
R. Capacitance
R. Voltage
Unit : mm
Size
code
fD±0.5
B6
C6
E7
F8
5.0
6.3
8.0
10.0
L
+0.1
−0.4
5.9
5.9
6.9
7.9
W±0.2 H±0.2 C±0.2
5.3
6.6
8.3
10.3
5.3
6.6
8.3
10.3
6.0
7.3
9.0
11.0
R
P±0.2
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
1.4
2.1
3.2
4.6
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Characteristics list
Rated
Rated
Series voltage capacitance
(V.DC)
(µF)
2.5
4.0
6.3
SVPA
10
82
180
330
820
68
150
270
680
47
120
220
470
68
150
330
39
16
20
82
180
10
22
47
Case size (mm)
fD
L
5.0
6.3
8.0
10.0
5.0
6.3
8.0
10.0
5.0
6.3
8.0
10.0
6.3
8.0
10.0
6.3
6.3
8.0
10.0
5.0
6.3
8.0
5.9
5.9
6.9
7.9
5.9
5.9
6.9
7.9
5.9
5.9
6.9
7.9
5.9
6.9
7.9
5.9
5.9
6.9
7.9
5.9
5.9
6.9
Size
code
B6
C6
E7
F8
B6
C6
E7
F8
B6
C6
E7
F8
C6
E7
F8
C6
E7
F8
B6
C6
E7
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
1970
30
0.12
2690
20
0.12
3370
20
0.12
4240
19
0.12
1970
30
0.12
2570
22
0.12
3220
22
0.12
4130
20
0.12
1970
30
0.12
2570
22
0.12
3220
22
0.12
4130
20
0.12
2200
30
0.12
2760
30
0.12
3770
24
0.12
2040
35
0.12
2460
24
0.12
2760
30
0.12
3430
29
0.12
1700
40
0.12
2040
35
0.12
2630
33
0.12
LC ✽4
(µA)
300
300
500
500
300
300
500
544
300
300
500
592
300
500
660
300
300
262
576
80
88
188
Standard (Reel size : f380)
Min.
Packaging Q'ty
Part number
(pcs)
2R5SVPA82MAA
1500
2R5SVPA180MAA
1000
2R5SVPA330MAA
1000
2R5SVPA820M
500
4SVPA68MAA
1500
4SVPA150MAA
1000
4SVPA270MAA
1000
4SVPA680M
500
6SVPA47MAA
1500
6SVPA120MAA
1000
6SVPA220MAA
1000
6SVPA470M
500
10SVPA68MAA
1000
10SVPA150MAA
1000
10SVPA330M
500
16SVPA39MAA
1000
16SVPA39MAAY
1000
16SVPA82MAA
1000
16SVPA180M
500
20SVPA10M
1500
20SVPA22M
1000
20SVPA47M
1000
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
120 Hz < f < 1 kHz
1 kHz < f < 10 kHz
10 kHz < f < 100 kHz
100 kHz < f < 500 kHz
Coefficient
0.05
0.3
0.7
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVPB
Features
● Low
profile (Height 5 mm max.)
compliance, Halogen free
● RoHS
Specifications
Size code
Category temperature range
Rated voltage range
Rated capacitance range
Capacitance tolerance
Leakage current
Dissipation factor (tan d)
Endurance
Damp heat
(Steady State)
C5
C55
–55 °C to +105 °C
2.5 V.DC to 20 V.DC
15 µF to 120 µF
20 V.DC
22 µF
±20 % (120 Hz / + 20 °C)
Please see the attached characteristics list
Please see the attached characteristics list
+105 °C, 1000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value (±30 % for C5 size)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
Dimensions (not to scale)
0.2 max.
W
–
Series
+
L
R. Capacitance
R. Voltage
Size
code
fD±0.5
C5
C55
6.3
6.3
C
H
fD
P
Polarity marking (−)
Lot. No.
L
+0.1
−0.4
R
W±0.2 H±0.2 C±0.2
4.9
5.4
6.6
6.6
6.6
6.6
7.3
7.3
Unit : mm
R
P±0.2
0.6 to 0.8
0.6 to 0.8
2.1
2.1
✽ Externals of figure are the reference.
Characteristics list
Rated
Rated
Series voltage capacitance
(V.DC)
(µF)
SVPB
2.5
4.0
6.3
10
16
20
120
100
82
56
33
15
22
Case size (mm)
fD
L
6.3
6.3
6.3
6.3
6.3
6.3
6.3
4.9
4.9
4.9
4.9
4.9
4.9
5.4
Size
code
C5
C55
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
1670
40
0.12
1670
40
0.12
1670
40
0.12
1670
40
0.12
1670
40
0.12
2000
45
0.12
2000
35
0.12
LC ✽4
(µA)
120
160
207
224
211
120
88
Standard (Reel size : f380)
Min.
Packaging Q'ty
Part number
(pcs)
2R5SVPB120M
1300
4SVPB100M
1300
6SVPB82M
1300
10SVPB56M
1300
16SVPB33M
1300
20SVPB15M
1300
20SVPB22M
1000
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
120 Hz < f < 1 kHz
1 kHz < f < 10 kHz
10 kHz < f < 100 kHz
100 kHz < f < 500 kHz
Coefficient
0.05
0.3
0.7
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVPS
Features
● 105
°C 5000 h
compliance, Halogen free
● RoHS
Specifications
Size code
A5
B6
C6
E7
F8
Category temperature range
–55 °C to +105 °C
Rated capacitance range 4 V.DC to 10 V.DC 4 V.DC to 16 V.DC 4 V.DC to 20 V.DC 4 V.DC to 25 V.DC 4 V.DC to 16 V.DC
Rated capacitance range 10 µF to 33 µF
22 µF to 68 µF
22 µF to 150 µF
10 µF to 270 µF 100 µF to 680 µF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+105 °C, 5000 h, rated voltage applied (25 V.DC → 20 V.DC applied)
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
Dimensions (not to scale)
0.2 max.
W
Polarity marking (−)
Lot. No.
C
H
fD
P
–
+
L
R
Series
R. Capacitance
R. Voltage
Unit : mm
Size
code
fD±0.5
+0.1
L −0.4
A5
B6
C6
E7
F8
4.0
5.0
6.3
8.0
10.0
5.4
5.9
5.9
6.9
7.9
W±0.2 H±0.2 C±0.2
4.3
5.3
6.6
8.3
10.3
4.3
5.3
6.6
8.3
10.3
5.0
6.0
7.3
9.0
11.0
R
P±0.2
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
1.0
1.4
2.1
3.2
4.6
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Characteristics list
Rated
Rated
Series voltage capacitance
(V.DC)
(µF)
4.0
6.3
SVPS
10
33
68
150
270
680
22
47
120
220
470
10
15
33
68
150
16
20
25
330
22
39
82
100
180
22
47
10
Case size (mm)
fD
L
4.0
5.0
6.3
8.0
10.0
4.0
5.0
6.3
8.0
10.0
4.0
4.0
5.0
6.3
8.0
10.0
10.0
5.0
6.3
8.0
10.0
10.0
6.3
8.0
8.0
5.4
5.9
5.9
6.9
7.9
5.4
5.9
5.9
6.9
7.9
5.4
5.4
5.9
5.9
6.9
7.9
7.9
5.9
5.9
6.9
7.9
7.9
5.9
6.9
6.9
Size
code
A5
B6
C6
E7
F8
A5
B6
C6
E7
F8
A5
B6
C6
E7
F8
B6
C6
E7
F8
C6
E7
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
740
200
0.15
1970
30
0.12
2570
22
0.12
3220
22
0.12
4130
20
0.12
740
200
0.12
1970
30
0.12
2570
22
0.12
3220
22
0.12
4130
20
0.12
700
220
0.10
740
200
0.10
1100
70
0.12
2200
30
0.12
2760
30
0.12
3020
30
0.12
3770
24
0.12
1060
90
0.10
2460
24
0.12
2760
30
0.12
2670
35
0.12
3430
29
0.12
1450
60
0.10
1890
45
0.12
1500
60
0.10
LC ✽4
(µA)
66
300
300
500
544
69.3
300
300
500
592
50
75
165
300
500
300
660
176
300
262
320
576
88
188
125
Standard (Reel size : f380)
Min.
Packaging Q'ty
Part number
(pcs)
4SVPS33M
2000
4SVPS68M
1500
4SVPS150M
1000
4SVPS270M
1000
4SVPS680M
500
6SVPS22M
2000
6SVPS47M
1500
6SVPS120M
1000
6SVPS220M
1000
6SVPS470M
500
10SVPS10M
2000
10SVPS15M
2000
10SVPS33M
1500
10SVPS68M
1000
10SVPS150MX
1000
10SVPS150M
500
10SVPS330M
500
16SVPS22M
1500
16SVPS39M
1000
16SVPS82M
1000
16SVPS100M
500
16SVPS180M
500
20SVPS22M
1000
20SVPS47M
1000
25SVPS10M
1000
✽1 Ripple current (100 kHz/ +105 °C ),
: The surface temperature of aluminum case top must not exceed 105 °C. A rise in temperature due to self-heating by ripple current should be factored in.
✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
120 Hz < f < 1 kHz
1 kHz < f < 10 kHz
10 kHz < f < 100 kHz
100 kHz < f < 500 kHz
Coefficient
0.05
0.3
0.7
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVQP
Features
● 125
°C 1000 h
compliance, Halogen free
● RoHS
Specifications
Size code
Category temperature range
Rated voltage range
Rated capacitance range
Capacitance tolerance
Leakage current
Dissipation factor (tan d)
Endurance
Damp heat
(Steady State)
C6
E7
–55 °C to +125 °C
4 V.DC to 20 V.DC
22 µF to 150 µF
6.3 V.DC to 20 V.DC
47 µF to 220 µF
±20 % (120 Hz / + 20 °C)
Please see the attached characteristics list
Please see the attached characteristics list
+125 °C, 1000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
Dimensions (not to scale)
0.2 max.
Series
+
L
R. Capacitance
Size
code
fD±0.5
R. Voltage
C6
E7
6.3
8.0
C
H
fD
P
Polarity marking (−)
Lot. No.
W
–
L
+0.1
−0.4
5.9
6.9
R
W±0.2 H±0.2 C±0.2
6.6
8.3
6.6
8.3
7.3
9.0
Unit : mm
R
P±0.2
0.6 to 0.8
0.6 to 0.8
2.1
3.2
✽ Externals of figure are the reference.
Characteristics list
Rated Rated
Series voltage capacitance
(V.DC) (µF)
4.0
6.3
SVQP
10
16
20
150
82
100
220
56
120
150
39
82
22
47
Case size (mm)
fD
L
6.3
6.3
6.3
8.0
6.3
8.0
8.0
6.3
8.0
6.3
8.3
5.9
5.9
5.9
6.9
5.9
6.9
6.9
5.9
6.9
5.9
6.9
Specifications
Size Ripple ✽1 Allowable ✽1
✽2
code current ripple current ESR
tan d ✽3
(mΩ max.)
(mAr.m.s.) (mAr.m.s.)
572
1810
40
0.12
C6
538
1700
45
0.12
572
1810
40
0.12
E7
810
2560
35
0.12
C6
538
1700
45
0.12
810
2560
35
0.12
E7
810
2560
35
0.12
C6
512
1620
50
0.10
E7
670
2120
40
0.12
C6
459
1450
60
0.10
E7
598
1890
45
0.12
✽4
LC
(µA)
300
258
315
693
280
600
750
312
656
220
470
Standard (Reel size : f380)
Min.
Part number
Packaging Q'ty
(pcs)
4SVQP150M
1000
6SVQP82M
1000
6SVQP100M
1000
6SVQP220M
1000
10SVQP56M
1000
10SVQP120M
1000
10SVQP150M
1000
16SVQP39M
1000
16SVQP82M
1000
20SVQP22M
1000
20SVQP47M
1000
✽1 Ripple current (100 kHz/ +105 °C < Tx < 125 °C), Allowable ripple current (100 kHz / Tx < 105 °C)
✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Surface Mount Type
Series : SVP
Features
● Standard
● Wealth
● RoHS
models
compliance, Halogen free
Specifications
Size code
A5
B6
C6
E7
F8
E12
F12
Category temperature range
–55 °C to +105 °C
Rated voltage range
4 V.DC to 16 V.DC 4 V.DC to 20 V.DC 2.5 V.DC to 20 V.DC
4 V.DC to 20 V.DC
2.5 V.DC to 20 V.DC
Rated capacitance range 3.3 µF to 33 µF 10 µF to 68 µF 22 µF to 220 µF 33 µF to 330 µF 56 µF to 680 µF 100 µF to 680 µF 150 µF to 1500 µF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+105 °C, 2000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
Dimensions (not to scale)
0.2 max.
W
Polarity marking (−)
Lot. No.
Series
R. Capacitance
R. Voltage
+
L
Size
code
fD±0.5
A5
B6
C6
E7
F8
E12
F12
4.0
5.0
6.3
8.0
10.0
8.0
10.0
C
H
fD
P
–
L
+0.1
−0.4
5.4
5.9
5.9
6.9
7.9
11.9
12.6
R
W±0.2 H±0.2 C±0.2
4.3
5.3
6.6
8.3
10.3
8.3
10.3
4.3
5.3
6.6
8.3
10.3
8.3
10.3
5.0
6.0
7.3
9.0
11.0
9.0
11.0
Unit : mm
R
P±0.2
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.8 to 1.1
0.8 to 1.1
1.0
1.4
2.1
3.2
4.6
3.2
4.6
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Characteristics list
Rated
Rated
Series voltage capacitance
(V.DC)
(µF)
2.5
4.0
6.3
220
680
1500
33
39
68
150
330
560
680
1200
22
47
82
100
120
220
330
470
SVP
10
820
4.7
6.8
10
15
33
47
56
120
150
270
330
16
560
3.3
15
22
39
56
82
100
150
180
20
330
10
22
27
33
47
56
68
100
150
Case size (mm)
fD
L
6.3
8.0
10.0
4.0
5.0
5.0
6.3
8.0
8.0
10.0
10.0
4.0
5.0
6.3
6.3
6.3
8.0
10.0
10.0
10.0
8.0
10.0
4.0
4.0
4.0
4.0
5.0
6.3
6.3
8.0
8.0
10.0
10.0
10.0
8.0
10.0
4.0
5.0
5.0
6.3
8.0
8.0
10.0
10.0
10.0
8.0
10.0
5.0
6.3
6.3
8.0
8.0
10.0
10.0
8.0
10.0
5.9
11.9
12.6
5.4
5.9
5.9
5.9
6.9
11.9
7.9
12.6
5.4
5.9
5.9
5.9
5.9
6.9
7.9
7.9
7.9
11.9
12.6
5.4
5.4
5.4
5.4
5.9
5.9
5.9
6.9
6.9
7.9
7.9
7.9
11.9
12.6
5.4
5.9
5.9
5.9
6.9
6.9
7.9
7.9
7.9
11.9
12.6
5.9
5.9
5.9
6.9
6.9
7.9
7.9
11.9
12.6
Size
code
C6
E12
F12
A5
B6
C6
E7
E12
F8
F12
A5
B6
C6
E7
F8
E12
F12
A5
B6
C6
E7
F8
E12
F12
A5
B6
C6
E7
F8
E12
F12
B6
C6
E7
F8
E12
F12
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
2390
23
0.12
4520
13
0.15
5440
12
0.18
740
200
0.15
1100
70
0.12
1400
60
0.12
1810
40
0.12
2560
35
0.12
4520
13
0.15
3700
25
0.12
5440
12
0.18
740
200
0.12
1100
70
0.12
1700
45
0.12
1810
40
0.12
2780
17
0.12
2560
35
0.12
3700
25
0.12
3700
25
0.12
3700
25
0.12
4210
15
0.15
5440
12
0.15
670
240
0.08
670
240
0.09
700
220
0.10
740
200
0.10
1100
70
0.12
1620
50
0.12
1700
45
0.12
2560
35
0.12
2560
35
0.12
3020
30
0.12
3700
25
0.12
3700
25
0.12
3950
17
0.15
5230
13
0.15
660
260
0.07
1020
120
0.10
1060
90
0.10
1620
50
0.10
1890
45
0.12
2120
40
0.12
2670
35
0.12
3020
30
0.12
3020
30
0.12
3640
20
0.15
4720
16
0.15
1020
120
0.10
1450
60
0.10
1450
60
0.10
1890
45
0.12
1890
45
0.12
2400
40
0.12
2400
40
0.12
3320
24
0.15
4320
20
0.15
LC ✽4
(µA)
110
340
750
66
78
136
120
264
448
544
960
69.3
148
103
126
151
277
277
416
592
592
775
23.5
34
50
75
165
94
112
240
300
300
540
660
660
840
26.4
120
176
125
179
262
320
480
576
576
792
100
88
108
132
188
224
272
400
600
Standard (Reel size : f380)
Min.
Packaging Q'ty
Part number
(pcs)
2R5SVP220M
1000
2R5SVP680M
400
2R5SVP1500M
400
4SVP33M
2000
4SVP39M
1500
4SVP68M
1500
4SVP150MX
1000
4SVP330M
1000
4SVP560M
400
4SVP680M
500
4SVP1200M
400
6SVP22M
2000
6SVP47M
1500
6SVP82M
1000
6SVP100M
1000
6SVP120MV
1000
6SVP220MX
1000
6SVP220M
500
6SVP330M
500
6SVP470MX
500
6SVP470M
400
6SVP820M
400
10SVP4R7M
2000
10SVP6R8M
2000
10SVP10M
2000
10SVP15M
2000
10SVP33M
1500
1000
10SVP47M
10SVP56M
1000
10SVP120M
1000
10SVP150MX
1000
10SVP150M
500
10SVP270M
500
10SVP330MX
500
10SVP330M
400
10SVP560M
400
16SVP3R3M
2000
16SVP15M
1500
16SVP22M
1500
16SVP39M
1000
16SVP56M
1000
16SVP82M
1000
16SVP100M
500
16SVP150M
500
16SVP180MX
500
16SVP180M
400
16SVP330M
400
20SVP10M
1500
20SVP22M
1000
20SVP27M
1000
20SVP33M
1000
20SVP47M
1000
20SVP56M
500
20SVP68M
500
20SVP100M
400
20SVP150M
400
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Radial Lead Type
Series : SXE
Features
● Super
● RoHS
high voltage (100 V.DC max.)
compliance, Halogen free
Specifications
Size code
Category temperature range
Rated voltage range
Rated capacitance range
Capacitance tolerance
Leakage current
Dissipation factor (tan d)
Endurance
Damp heat
(Steady State)
E12
–55 °C to +105 °C
63 V.DC to 100 V.DC
15 µF to 33 µF
±20 % (120 Hz / + 20 °C)
Please see the attached characteristics list
Please see the attached characteristics list
+105 °C, 5000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Dimensions (not to scale)
fd±0.05
fD±0.5
Polarity marking (−)
Lot. No.
+
F
Marking
–
Series
L max.
15 min. 4 min.
19 min.
Unit : mm
R. Capacitance
Size code
R. Voltage
E12
fD±0.5
8.0
L max.
12.0
F±0.5
3.5
fd±0.05
0.6
✽ Externals of figure are the reference.
Characteristics list
Series
SXE
Rated
Rated
voltage capacitance
(V.DC)
(µF)
63
100
33
15
Case size (mm)
fD
L
8.0
8.0
12.0
12.0
Size
code
E12
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
2950
25
0.12
2350
40
0.12
LC ✽4
(µA)
104
75
Part number
63SXE33M
100SXE15M
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Radial Lead Type
Series : SEPF
Features
● High voltage (35 V.DC max.)
● Large capacitance (1000 μF max.)
● RoHS compliance, Halogen free
Specifications
Size code
C55
C6
E7
E12
F13
Category temperature range
–55 °C to +105 °C
Rated voltage range
16 V.DC to 32 V.DC
16 V.DC to 35 V.DC
Rated capacitance range 22 μF to 150 μF
22 μF to 180 μF
39 μF to 270 μF
82 μF to 560 μF 120 μF to 1000 μF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+105 °C, 5000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
Dimensions (not to scale)
Unit : mm
fD±0.5
fd±0.05
Series
R. Voltage
+
–
L max.
R. Capacitance
Size code
C55
C6
E7
E12
F13
F
Polarity marking (−)
Lot. No.
15 min. 4 min.
19 min.
✽ Externals of figure are the reference.
fD±0.5 L max. F±0.5 fd±0.05
6.3
5.5
2.5
0.45
6.3
6.0
2.5
0.5
8.0
7.0
3.5
0.5 ✽
8.0
12.0
3.5
0.6
10.0
13.0
5.0
0.6
✽ 32SEPF68M : 0.6±0.05
Characteristics list
Series
Rated
Rated
voltage capacitance
(V.DC)
(μF)
16
20
SEPF
25
32
35
150
180
270
560
1000
120
180
390
560
56
82
180
330
22
68
22
39
82
120
Case size (mm)
fD
L
Size
code
6.3
6.3
8.0
8.0
10.0
6.3
8.0
8.0
10.0
6.3
8.0
8.0
10.0
6.3
8.0
6.3
8.0
8.0
10.0
5.5
6.0
7.0
12.0
13.0
6.0
7.0
12.0
13.0
6.0
7.0
12.0
13.0
5.5
7.0
6.0
7.0
12.0
13.0
C55
C6
E7
E12
F13
C6
E7
E12
F13
C6
E7
E12
F13
C55
E7
C6
E7
E12
F13
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
2590
3300
3300
4950
5400
3200
3200
4950
5400
2800
3000
4650
5000
2400
3200
2600
2800
4000
4400
30
22
22
14
12
25
25
14
12
30
28
16
14
35
25
35
30
20
18
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.10
0.12
0.12
0.12
0.12
LC ✽4
(μA)
Part number
480
576
864
1792
3200
480
720
1560
2240
280
410
900
1650
140
435
154
273
574
840
16SEPF150M
16SEPF180M
16SEPF270M
16SEPF560M
16SEPF1000M
20SEPF120M
20SEPF180M
20SEPF390M
20SEPF560M
25SEPF56M
25SEPF82M
25SEPF180M
25SEPF330M
32SEPF22M
32SEPF68M
35SEPF22M
35SEPF39M
35SEPF82M
35SEPF120M
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Radial Lead Type
Series : SEPC
Features
● Super
low ESR (5 mΩ to 24 mΩ)
capacitance (2700 μF max.)
● RoHS compliance, Halogen free
● Large
Specifications
Size code
B9
C55
C6
C9
E7
E9
E12
E13
F13
Category temperature range
–55 °C to +105 °C
Rated voltage range (V.DC)
2.5
6.3
2.5 to 16
6.3 to 16 2.5 to 16
16
2.5 to 6.3 2.5 to 16
Rated capacitance range (μF) 100 to 560
220
100 to 560 100 to 820 150 to 1000 180 to 1000 180 to 270 470 to 820 470 to 2700
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+105 °C, 5000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Marking
Dimensions (not to scale)
E12, E13, F13 Size
Unit : mm
Polarity marking (−)
Lot. No.
–
L
15 min. 4 min.
19 min.
B9, C55, C6, C9, E7, E9 Size
fd
+
R. Voltage
fD
R. Capacitance
–
L
15 min. 4 min.
19 min.
B9, C55, C6, C9, E7, E9 size flat rubber is used.
F
Series
+
F
fD
fd
Size code fD±0.5 L max. F±0.5 fd±0.05
B9
5.0
9.0
2.0 0.6
C55
6.3
5.5
2.5 0.45
C6
6.3
6.0
2.5 0.45 ✽1
C9
6.3
9.0
2.5 0.6
E7
8.0
7.0
3.5 0.6 ✽2
E9
8.0
9.0
3.5 0.6
E12
8.0
12.0
3.5 0.6
E13
8.0
13.0
3.5 0.6
F13
10.0
13.0
5.0 0.6
✽1 2SEPC390M, 2SEPC560M : 0.5±0.05
✽2 16SEPC150MD, 10SEPC270M : 0.45±0.05
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Characteristics list
Series
Rated
Rated
voltage capacitance
(V.DC)
(μF)
100
300
390
470
560
2.5
820
1000
2700
560
4.0
680
820
220
SEPC
470
6.3
10
560
680
1000
1500
270
100
150
16
180
220
270
470
Case size (mm)
fD
L
5.0
5.0
6.3
5.0
5.0
6.3
6.3
8.0
6.3
8.0
8.0
8.0
8.0
8.0
10.0
6.3
8.0
8.0
8.0
10.0
6.3
6.3
8.0
8.0
6.3
8.0
10.0
8.0
10.0
8.0
6.3
6.3
8.0
8.0
8.0
8.0
8.0
8.0
10.0
9.0
9.0
6.0
9.0
9.0
6.0
9.0
9.0
9.0
7.0
9.0
9.0
13.0
9.0
13.0
9.0
9.0
13.0
13.0
13.0
5.5
9.0
9.0
13.0
9.0
9.0
13.0
7.0
13.0
7.0
6.0
9.0
7.0
9.0
12.0
7.0
9.0
12.0
13.0
Size
code
B9
C6
B9
C6
C9
E9
C9
E7
E9
E13
E9
F13
C9
E9
E13
F13
C55
C9
E9
E13
C9
E9
E13
E7
F13
E7
C6
C9
E7
E9
E12
E7
E9
E12
F13
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
4180
7
0.10
4180
7
0.10
3900
10
0.12
4180
7
0.10
4180
7
0.10
3900
10
0.12
5600
7
0.10
4700
8
0.10
5600
7
0.10
5300
8
0.10
6100
7
0.10
7200
5
0.10
6100
7
0.10
6100
7
0.10
5560
10
0.10
5600
7
0.10
6100
7
0.10
6100
7
0.10
6100
7
0.10
6640
7
0.10
2980
18
0.12
5600
7
0.10
5700
8
0.10
5700
8
0.10
5600
7
0.10
6100
7
0.10
6640
7
0.10
3530
18
0.10
5560
10
0.10
3220
22
0.12
2490
24
0.10
4680
10
0.10
3220
22
0.12
5000
10
0.10
4360
16
0.10
4150
13
0.10
5000
10
0.10
5000
11
0.10
6100
10
0.10
LC ✽4
(μA)
Part number
500
500
500
500
500
500
500
280
500
500
500
500
500
500
1350
500
500
500
544
656
280
592
592
592
705
705
857
1260
1890
500
320
500
500
576
576
500
864
864
1504
2SEPC100MZ
2SEPC330MZ
2SEPC390M
2SEPC470MZ
2SEPC560MZ
2SEPC560M
2SEPC560MW
2SEPC560MX
2SEPC820MW
2SEPC820MD
2SEPC820MX
2SEPC820MY
2R5SEPC820M
2SEPC1000MX
2SEPC2700M
4SEPC560MW
4SEPC560MX
4SEPC560M
4SEPC680M
4SEPC820M
6SEPC220M
6SEPC470MW
6SEPC470MX
6SEPC470M
6SEPC560MW
6SEPC560MX
6SEPC680M
6SEPC1000MD
6SEPC1500M
10SEPC270MD
16SEPC100M
16SEPC100MW
16SEPC150MD
16SEPC180MX
16SEPC180M
16SEPC220MD
16SEPC270MX
16SEPC270M
16SEPC470M
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Radial Lead Type
Series : SEQP
Features
● High
voltage (32 V.DC max.)
°C 1000 h
● RoHS compliance, Halogen free
● 125
Specifications
Size code
C6
E7
F8
E12
F13
Category temperature range
–55 °C to +125 °C
Rated voltage range
4 V.DC to 20 V.DC
4 V.DC to 32 V.DC
4 V.DC to 20 V.DC
Rated capacitance range 22 µF to 150 µF 6.8 µF to 330 µF 15 µF to 680 µF
18 µF to 560 µF 150 µF to 1200 µF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+125 °C, 1000 h/+105 °C, 5000 h, rated voltage applied
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Dimensions (not to scale)
fD
fd
Polarity marking (−)
Lot. No.
+
F
Marking
–
L
15 min. 4 min.
19 min.
Series
Unit : mm
Size code
R. Capacitance
R. Voltage
C6
E7
F8
E12
F13
fD±0.5
6.3
8.0
10.0
8.0
10.0
L max.
6.0
7.0
8.0
12.0
13.0
F±0.5
2.5
3.5
5.0
3.5
5.0
fd±0.05
0.45
0.45
0.50
0.60
0.60
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Characteristics list
Rated
Rated
Series voltage capacitance
(V.DC)
(µF)
4.0
6.3
10
SEQP
16
20
32
150
330
560
680
1200
82
150
330
470
820
56
120
270
330
560
39
82
150
180
330
22
47
68
100
150
6.8
15
18
Case size (mm)
fD
L
Size
code
6.3
8.0
8.0
10.0
10.0
6.3
8.0
10.0
8.0
10.0
6.3
8.0
10.0
8.0
10.0
6.3
8.0
10.0
8.0
10.0
6.3
8.0
10.0
8.0
10.0
8.0
10.0
8.0
6.0
7.0
12.0
8.0
13.0
6.0
7.0
8.0
12.0
13.0
6.0
7.0
8.0
12.0
13.0
6.0
7.0
8.0
12.0
13.0
6.0
7.0
8.0
12.0
13.0
7.0
8.0
12.0
C6
E7
E12
F8
F13
C6
E7
F8
E12
F13
C6
E7
F8
E12
F13
C6
E7
F8
E12
F13
C6
E7
F8
E12
F13
E7
F8
E12
Specifications
Ripple ✽1 Allowable ✽1
ESR ✽2
current ripple current
tan d ✽3
(mΩ max.)
(mAr.m.s.) (mAr.m.s.)
572
1810
40
0.12
810
2560
35
0.12
1430
4520
13
0.15
1170
3700
25
0.12
1721
5440
12
0.18
537
1700
45
0.12
810
2560
35
0.12
1170
3700
25
0.12
1332
4210
15
0.15
1721
5440
12
0.15
537
1700
45
0.12
810
2560
35
0.12
1170
3700
25
0.12
1250
3950
17
0.15
1655
5230
13
0.15
512
1620
50
0.10
670
2120
40
0.12
955
3020
30
0.12
1151
3640
20
0.15
1493
4720
16
0.15
458
1450
60
0.10
598
1890
45
0.12
759
2400
40
0.12
1050
3320
24
0.15
1367
4320
20
0.15
440
1400
100
0.10
560
1800
80
0.10
790
2500
50
0.12
LC ✽4
(µA)
Part number
300
660
448
544
960
258
472
416
592
775
280
600
540
660
840
312
656
480
576
792
220
470
272
400
600
44
96
115
4SEQP150M
4SEQP330M
4SEQP560M
4SEQP680M
4SEQP1200M
6SEQP82M
6SEQP150M
6SEQP330M
6SEQP470M
6SEQP820M
10SEQP56M
10SEQP120M
10SEQP270M
10SEQP330M
10SEQP560M
16SEQP39M
16SEQP82M
16SEQP150M
16SEQP180M
16SEQP330M
20SEQP22M
20SEQP47M
20SEQP68M
20SEQP100M
20SEQP150M
32SEQP6R8M
32SEQP15M
32SEQP18M
✽1 Ripple current (100 kHz/ +105 °C < Tx < 125 °C), Allowable ripple current (100 kHz / Tx < 105 °C)
✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Radial Lead Type
Series : SEP
Features
● Standard
● 105
°C 3000 h
compliance, Halogen free
● RoHS
Specifications
Size code
C6
E7
F8
E12
F13
Category temperature range
–55 °C to +105 °C
Rated voltage range
4 V.DC to 20 V.DC
2.5 V.DC to 20 V.DC
Rated capacitance range 22 µF to 150 µF
33 µF to 330 µF
56 µF to 680 µF 100 µF to 680 µF 150 µF to 1500 µF
Capacitance tolerance
±20 % (120 Hz / + 20 °C)
Leakage current
Please see the attached characteristics list
Dissipation factor (tan d)
Please see the attached characteristics list
+105 °C, 3000 h, rated voltage applied (2.5 V.DC 2000 h applied)
Capacitance change Within ±20 % of the initial value
Endurance
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit
+60 °C, 90 % to 95 %, 1000 h, No-applied voltage
Capacitance change Within ±20 % of the initial value
Damp heat
(Steady State)
tan d
< 150 % of the initial limit
DC leakage current Within the initial limit (after voltage processing)
Dimensions (not to scale)
fD
fd
Polarity marking (−)
Lot. No.
+
F
Marking
–
L
15 min. 4 min.
19 min.
Series
Unit : mm
Size code
R. Capacitance
R. Voltage
C6
E7
F8
E12
F13
fD±0.5
6.3
8.0
10.0
8.0
10.0
L max.
6.0
7.0
8.0
12.0
13.0
F±0.5
2.5
3.5
5.0
3.5
5.0
fd±0.05
0.45
0.45
0.50
0.60
0.60
✽ Externals of figure are the reference.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
Conductive Polymer Aluminum Solid Capacitors
Characteristics list
Series
Rated
Rated
voltage capacitance
(V.DC)
(µF)
2.5
4.0
6.3
SEP
10
16
20
680
1500
100
150
220
330
470
560
680
1200
82
150
330
470
820
56
120
270
330
560
39
82
150
180
330
22
33
47
56
68
100
150
Case size (mm)
fD
L
8.0
10.0
6.3
6.3
8.0
8.0
10.0
8.0
10.0
10.0
6.3
8.0
10.0
8.0
10.0
6.3
8.0
10.0
8.0
10.0
6.3
8.0
10.0
8.0
10.0
6.3
8.0
8.0
10.0
10.0
10.0
8.0
10.0
12.0
13.0
6.0
6.0
7.0
7.0
8.0
12.0
8.0
13.0
6.0
7.0
8.0
12.0
13.0
6.0
7.0
8.0
12.0
13.0
6.0
7.0
8.0
12.0
13.0
6.0
7.0
7.0
8.0
8.0
8.0
12.0
13.0
Size
code
E12
F13
C6
E7
F8
E12
F8
F13
C6
E7
F8
E12
F13
C6
E7
F8
E12
F13
C6
E7
F8
E12
F13
C6
E7
F8
E12
F13
Specifications
Ripple ✽1
ESR ✽2
current
tan d ✽3
(mΩ max.)
(mAr.m.s.)
4520
13
0.15
5440
12
0.18
1810
40
0.12
1810
40
0.12
2560
35
0.12
2560
35
0.12
3700
25
0.12
4520
13
0.15
3700
25
0.12
5440
12
0.18
1700
45
0.12
2560
35
0.12
3700
25
0.12
4210
15
0.15
5440
12
0.15
1700
45
0.12
2560
35
0.12
3700
25
0.12
3950
17
0.15
5230
13
0.15
1620
50
0.10
2120
40
0.12
3020
30
0.12
3640
20
0.15
4720
16
0.15
1450
60
0.10
1890
45
0.12
1890
45
0.12
2400
40
0.12
2400
40
0.12
2570
35
0.12
3320
24
0.15
4320
20
0.15
LC ✽4
(µA)
Part number
340
750
200
300
440
660
376
448
544
960
258
472
416
592
775
280
600
540
660
840
312
656
480
576
792
220
330
470
224
272
400
400
600
2R5SEP680M
2R5SEP1500M
4SEP100M
4SEP150M
4SEP220M
4SEP330M
4SEP470M
4SEP560M
4SEP680M
4SEP1200M
6SEP82M
6SEP150M
6SEP330M
6SEP470M
6SEP820M
10SEP56M
10SEP120M
10SEP270M
10SEP330M
10SEP560M
16SEP39M
16SEP82M
16SEP150M
16SEP180M
16SEP330M
20SEP22M
20SEP33M
20SEP47M
20SEP56M
20SEP68M
20SEP100MX
20SEP100M
20SEP150M
✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes
◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”.
Frequency correction factor for ripple current
Frequency
Coefficient
120 Hz < f < 1 kHz
0.05
1 kHz < f < 10 kHz
0.3
10 kHz < f < 100 kHz
0.7
100 kHz < f < 500 kHz
1
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Nov. 2015
CAUTION AND WARNING
1. The electronic components contained in this catalog are designed and produced for use in home electric appliances, office eq uipment, information equipment,
communications equipment, and other general purpose electronic devices.
Before use of any of these components for equipment that requires a high degree of safety, such as medical instruments, aeros pace equipment, disaster-prevention
equipment, security equipment, vehicles (automobile, train, vessel),
please be sure to contact our sales representative.
2. When applying one of these components for equipment requiring a high degree of safety, no matter what sort of application it might be, be sure to install a protective
circuit or redundancy arrangement to enhance the safety of your equipment. In addition, please carry out the safety test on your own responsibility.
3. When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on thespecifications with us in advance.
4. Technical information contained in this catalog is intended to convey examples of typical performances and/or applications a nd is not intended to make any
warranty with respect to the intellectual property rights or any other related rights of our company or any third parties nor grant any license under such rights.
5. In order to export products in this catalog, the exporter may be subject to the export license requirement under the Foreign Exchange and Foreign Trade Law of
Japan.
6. No ozone-depleting substances (ODSs) under the Montreal Protocol are used in the manufacturing processes of Automotive & Ind ustrial Systems Company, Panasonic
Corporation.
Please contact
Factory
The information in this catalog is valid as of December 2015.
Similar pages