Aluminum Electrolytic Capacitors (Radial Lead Type)[pdf :1.29 MB]

2016
Products Catalog
Aluminum Electrolytic Capacitors
Radial lead type
2016.04
http://industrial.panasonic.com/ww/products/capacitors/aluminum-capacitors/aluminum-cap-lead
——— Notices ———
■ Applicable Laws and Regulations
● This product complies with the RoHS Directive (Restriction of the use of certain Hazardous substances in
electrical and electronic equipment (DIRECTIVE 2011/65/EU).
● No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in
producing this product.
● We do not PBBs or PBDEs as brominated flame retardants.
● Export procedure which followed export related regulations, such as foreign exchange and a foreign trade
method, on the occasion of export of this product Thank you for your consideration.
■ Limited applications
● This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home
appliances, computers and other office equipment, optical equipment, measuring equipment.
● High reliability and safety are required [ be / a possibility that incorrect operation of this product may do harm
to a human life or property ] more. When use is considered by the use, the delivery specifications which suited
the use separately need to be exchanged.
——— Items to be observed ———
● This specification guarantees the quality and performance of the product as individual components.
Before use, check and evaluate their compatibility with installed in your products.
● Do not use the products beyond the specifications described in this document.
■ For specifications
● Install the following systems for a failsafe design to ensure safety if these products are to be used in
equipment where a defect in these products may cause the loss of human life or other signification damage,
such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment,
electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime
prevention equipment.
· The system is equipped with a protection circuit and protection device.
· The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event of
a single fault.
■ Conditions of use
● Before using the products, carefully check the effects on their quality and performance, and determined
whether or not they can be used. These products are designed and manufactured for general-purpose and
standard use in general electronic equipment. These products are not intended for use in the following special
conditions.
(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent.
(2) In direct sunlight, outdoors, or in dust.
(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a
high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NOx.
(4) In an environment where strong static electricity or electromagnetic waves exist.
(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near
these products.
(6) Sealing or coating of these products or a printed circuit board on which these products are mounted,
with resin and other material.
(7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular,
when using water or a water-soluble cleaning agent, be careful not to leave water residues)
(8) Using in the atmosphere which strays Acid or alkaline.
(9) Using in the atmosphere which there are excessive vibration and shock.
● Please arrange circuit design for preventing impulse or transitional voltage.
Do not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage,
instantaneous high voltage, high pulse voltage etc.
● Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid
deterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and
affects performance, characteristics, and functions of customer system.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Nov. 2015
Aluminum Electrolytic Capacitors (Radial Lead Type)
Application Guidelines (Radial Lead Type)
1. Circuit design
1.1 Operating Temperature and Frequency
Electrical parameters for electrolytic capacitors are normally specified at 20 °C temperature and 120 Hz frequency.
These parameters vary with changes in temperature and frequency. Circuit designers should take these
changes into consideration.
(1) Effects of operating temperature on electrical parameters
(a) At higher temperatures, leakage current and capacitance increase while equivalent series resistance
(ESR) decreases.
(b) At lower temperatures, leakage current and capacitance decrease while equivalent series resistance
(ESR) increases.
(2) Effects of frequency on electrical parameters
(a) At higher frequencies, capacitance and impedance decrease while tan d increases.
(b) At lower frequencies, heat generated by ripple current will rise due to an increase in equivalent series
resistance (ESR).
1.2 Operating Temperature and Life Expectancy
(1) Expected life is affected by operating temperature. Generally, each 10 °C reduction in temperature will
double the expected life.
Use capacitors at the lowest possible temperature below the upper category temperature.
(2) If operating temperatures exceed the upper category limit, rapid deterioration of electrical parameter will
occur and irreversible damage will result.
Check for the maximum capacitor operating temperatures including ambient temperature, internal capacitor
temperature rise due to ripple current, and the effects of radiated heat from power transistors, IC's or resistors.
Avoid placing components, which could conduct heat to the capacitor from the back side of the circuit board.
(3) The formula for calculating expected life at lower operating temperatures is as follows;
L2 = L1×2
( T10-T )
1
2
L1 : Guaranteed life (h) at temperature, T1 °C
L2 : Expected life (h) at temperature, T2 °C
T1 : Upper category temperature + temperature rise due to rated ripple current (°C)
T2 : Actual operating temperature, ambient temperature + temperature rise due to ripple current (°C)
(4) Please use according to the lifetime as noted in this specification. Using products beyond end of the
lifetime may change characteristics rapidly, short-circuit, operate pressure relief vent, or leak electrolyte.
1.3 Common Application Conditions to Avoid
The following misapplication load conditions will cause rapid deterioration of a capacitor’s electrical parameters.
In addition, rapid heating and gas generation within the capacitor can occur, causing the pressure relief vent to
operate and resultant leakage of electrolyte. Under extreme conditions, explosion and fi re ignition could result.
The leaked electrolyte is combustible and electrically conductive.
(1) Reverse Voltage
DC capacitors have polarity. Verify correct polarity before insertion. For circuits with changing or uncertain
polarity, use DC bipolar capacitors. DC bipolar capacitors are not suitable for use in AC circuits.
(2) Charge / Discharge Applications
Standard capacitors are not suitable for use in repeating charge/discharge applications. For charge/
discharge applications, consult us with your actual application condition.
For rush current, please to not exceed 100 A.
(3) ON-OFF circuit
Do not use capacitors in circuit where ON-OFF switching is repeated more than 10000 times/per day.
In case of applying to the theses ON-OFF circuit, consult with us about circuit condition and so on.
(4) Over voltage
Do not apply voltages exceeding the maximum specified rated voltage. Voltages up to the surge voltage
rating are acceptable for short periods of time.
Ensure that the sum of the DC voltage and the superimposed AC ripple voltage does not exceed the
rated voltage.
(5) Ripple Current
Do not apply ripple currents exceeding the maximum specified value. For high ripple current applications,
use a capacitor designed for high ripple currents. In addition, consult us if the applied ripple current is to
be higher than the maximum specified value.
Ensure that rated ripple currents that superimposed on low DC bias voltages do not cause reverse
voltage conditions.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
1.4 Using Two or More Capacitors in Series or Parallel
(1) Capacitors Connected in Parallel
The circuit resistance can closely approximate the series resistance of the capacitor, causing an
imbalance of ripple current loads within the capacitors. Careful wiring methods can minimize the possible
application of an excessive ripple current to a capacitor.
(2) Capacitors Connected in Series
Differences in normal DC leakage current among capacitors can cause voltage imbalances.
The use of voltage divider shunt resistors with consideration to leakage currents can prevent capacitor
voltage imbalances.
1.5 Capacitor Mounting Considerations
(1) Double-Sided Circuit Boards
Avoid wiring pattern runs, which pass between the mounted capacitor and the circuit board. When dipping
into a solder bath, an excess solder may deposit under the capacitor by capillary action, causing short
circuit between anode and cathode terminals.
(2) Circuit Board Hole Positioning
The vinyl sleeve of the capacitor can be damaged if solder passes through a lead hole into the
subsequently processed parts.
Special care when locating hole positions in proximity to capacitors is recommended.
(3) Circuit Board Hole Spacing
The spacing of circuit board holes should match the lead wire spacing of capacitors within the specified tolerances.
Incorrect spacing can cause an excessive lead wire stress during the insertion process.
This may result in premature capacitor failure due to the short or open circuit, increased leakage current, or
electrolyte leakage.
(4) Clearance for Case Mounted Pressure Relief
Capacitors with case mounted pressure relief require sufficient clearance to allow for proper pressure relief
operation.
The minimum clearance are dependent on capacitor diameters as follows.
(Dia 6.3 mm to Dia 16 mm : 2 mm minimum, Dia 18 mm : 3 mm minimum)
(5) Wiring Near the Pressure Relief
Avoid locating high voltage or high current wiring or circuit board paths above the pressure relief.
Flammable, high temperature gas that exceeds 100 °C may be released which could dissolve the wire
insulation and ignite.
(6) Circuit Board Patterns Under the Capacitor
Avoid circuit board runs under the capacitor, as an electrical short can occur due to an electrolyte leakage.
(7) Please note the resonant after product implementation
The vicinity of the resonant point will take a heavy load on the capacitor.
Capacitors can cause rapid change in characteristics and dropout by this load.
1.6 Electrical Isolation of the Capacitor
Completely isolate the capacitor as follows.
Between the cathode and the case and between the anode terminal and other circuit paths.
1.7 Capacitor Sleeve
The vinyl sleeve or laminate coating is intended for marking and identification purposes and is not meant to
electrically insulate the capacitor.
The sleeve may split or crack if immersed into solvents such as toluene or xylene and then subsequently
exposed to high temperatures.
2. Capacitor Handling Techniques
2.1 Considerations Before Using
(1) Capacitors have a finite life. Do not reuse or recycle capacitors from used equipment.
(2) Transient recovery voltage may be generated in the capacitor due to dielectric absorption.
If required, this voltage can be discharged with a resistor with a value of about 1 kΩ.
(3) Capacitors stored for a long period of time may exhibit an increase in leakage current.
This can be corrected by gradually applying rated voltage in series with a resistor of approximately 1 kΩ.
(4) If capacitors are dropped, they can be damaged mechanically or electrically. Avoid using dropped
capacitors.
(5) Dented or crushed capacitors should not be used. The seal integrity can be damaged and loss of
electrolyte/shortened life can result.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
2.2 Capacitor Insertion
(1)
(2)
(3)
(4)
Verify the correct capacitance and rated voltage of the capacitor.
Verify the correct polarity of the capacitor before insertion.
Verify the correct hole spacing and land pattern size before insertion to avoid stress on the terminals.
Ensure that the lead clinching operation done by auto insertion equipments does not stress the capacitor
leads where they enter the seal of the capacitor.
2.3 Flow Soldering
(1) Do not immerse the capacitor body into the solder bath as excessive internal pressure could result.
(2) Apply proper soldering conditions (temperature, time, etc.). Do not exceed the specified limits.
(3) Do not allow other parts or components to touch the capacitor during soldering.
2.4 Manual Soldering
(1) Apply soldering conditions (temperature and time) based on the specification, or do not exceed
temperature of 350 °C for 3 seconds or less.
(2) If lead wires must be modified to meet terminal board hole spacing, avoid stress on the lead wire where
it enters the capacitor seal.
(3) If a soldered capacitor must be removed and reinserted, avoid excessive stress on the capacitor leads.
(4) Avoid physical contacts between the tip of the soldering iron and capacitors to prevent melting of the vinyl sleeve.
2.5 Other Soldering Considerations
Rapid temperature rise during the preheat operation and resin bonding operation can cause cracking of the
capacitor’s vinyl sleeve.
For heat curing, do not exceed 150 °C for the maximum time of 2 minutes.
2.6 Capacitor Handling after Soldering
(1) Avoid moving the capacitor after soldering to prevent excessive stress on the lead wires where they enter the seal.
(2) Do not use the capacitor as a handle when moving the circuit board assembly.
(3) Avoid striking the capacitor after assembly to prevent failure due to excessive shock.
2.7 Circuit Board Cleaning
(1) Circuit boards can be immersed or ultrasonically cleaned using suitable cleaning solvents for up to 5 minutes
and up to 60 °C maximum temperatures. The boards should be thoroughly rinsed and dried.
The use of ozone depleting cleaning agents is not recommended for the purpose of protecting our environment.
(2) Avoid using the following solvent groups unless specifically allowed in the specification ;
(a) Halogenated cleaning solvents: except for solvent resistant capacitor types, halogenated solvents can
permeate the seal and cause internal capacitor corrosion and failure.
For solvent resistant capacitors, carefully follow the temperature and time requirements based on the specification.
1,1,1-trichloroethane should never be used on any aluminum electrolytic capacitor.
(b) Alkaline solvents
: could react and dissolve the aluminum case.
(c) Petroleum based solvents : deterioration of the rubber seal could result.
(d) Xylene
: deterioration of the rubber seal could result.
(e) Acetone
: removal of the ink markings on the vinyl sleeve could result.
(3) A thorough drying after cleaning is required to remove residual cleaning solvents that may be trapped
between the capacitor and the circuit board. Avoid drying temperatures, which exceed the Upper category
temperature of the capacitor.
(4) Monitor the contamination levels of the cleaning solvents during use in terms of electrical conductivity,
pH, specific gravity, or water content. Chlorine levels can rise with contamination and adversely affect the
performance of the capacitor.
(5) Depending on the cleaning method, the marking on a capacitor may be erased or blurred.
Please consult us if you are not certain about acceptable cleaning solvents or cleaning methods.
2.8 Mounting Adhesives and Coating Agents
When using mounting adhesives or coating agents to control humidity, avoid using materials containing
halogenated solvents.
Also, avoid the use of chloroprene based polymers.
Harden on dry adhesive or coating agents well lest the solvent should be left.
After applying adhesives or coatings, dry thoroughly to prevent residual solvents from being trapped between
the capacitor and the circuit board.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
2.9 Fumigation
In exporting electronic appliances with aluminum electrolytic capacitors, in some cases fumigation treatment
using such halogen compound as methyl bromide is conducted for wooden boxes.
If such boxes are not dried well, the halogen left in the box is dispersed while transported and enters in the
capacitors inside.
This possibly causes electrical corrosion of the capacitors. Therefore, after performing fumigation and drying
make sure that no halogen is left.
Don’t perform fumigation treatment to the whole electronic appliances packed in a box.
3. Precautions for using capacitors
3.1 Environmental Conditions
Capacitors should not be used in the following environments.
(1) Exposure to temperatures above the upper category or below the lower category temperature of the capacitor.
(2) Direct contact with water, salt water, or oil.
(3) High humidity conditions where water could condense on the capacitor.
(4) Exposure to toxic gases such as hydrogen sulfide, sulfuric acid, nitric acid, chlorine, Chlorine compound,
Bromine, Bromine compound or ammonia.
(5) Exposure to ozone, radiation, or ultraviolet rays.
(6) Vibration and shock conditions exceeding specified requirements.
3.2 Electrical Precautions
(1) Avoid touching the terminals of a capacitor as a possible electric shock could result. The exposed
aluminum case is not insulated and could also cause electric shock if touched.
(2) Avoid short circuiting the area between the capacitor terminals with conductive materials including liquids
such as acids or alkaline solutions.
(3) A low-molecular-weight-shiroxane which is included in a silicon material shall causes abnormal electrical
characteristics.
4. Emergency Procedures
(1) If the pressure relief of the capacitor operates, immediately turn off the equipment and disconnect from the power source.
This will minimize an additional damage caused by the vaporizing electrolyte.
(2) Avoid contact with the escaping electrolyte gas, which can exceed 100 °C temperatures.
If electrolyte or gas enters the eye, immediately flush the eye with large amounts of water.
If electrolyte or gas is ingested by mouth, gargle with water.
If electrolyte contacts the skin, wash with soap and water.
5. Long Term Storage
Leakage current of a capacitor increases with long storage times. The aluminum oxide film deteriorates as a
function of temperature and time.
If used without reconditioning, an abnormally high current will be required to restore the oxide film.
This surge current could cause the circuit or the capacitor to fail.
Expiration date is 42 months from outgoing inspection date.
However, expiration date for series which are not listed below is 12 months from outgoing inspection date.
Series
FC, FK, HD, TA, TP
Expiration date
42 months from outgoing inspection date
For storage condition, keep room temperature (5 °C to 35 °C) and humidity (45 % to 85 %) where direct
sunshine doesn't reach.
5.1 Environmental Conditions
Do
(1)
(2)
(3)
(4)
not store under condition outside the area described in the specification, and also under conditions listed below.
Exposure to temperatures above the upper category or below the lower category temperature of the capacitor.
Direct contact with water, salt water, or oil.
High humidity conditions where water could condense on the capacitor.
Exposure to toxic gases such as hydrogen sulfide, sulfuric acid, nitric acid, chlorine, Chlorine compound,
Bromine, Bromine compound or ammonia.
(5) Exposure to ozone, radiation, or ultraviolet rays.
(6) Vibration and shock conditions exceeding specified requirements.
6. Capacitor Disposal
When disposing capacitors, use one of the following methods.
(1) Incinerate after crushing the capacitor or puncturing the can wall (to prevent explosion due to internal pressure rise).
(2) Dispose as solid waste.
NOTE : Local laws may have specific disposal requirements which must be followed.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Jun. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Diagram
◼ Radial lead type
Low impedance
Long Life · High ripple
EE series
TP series
105 °C
8000 h to 10000 h
135 °C/1000 h to 2000 h
125 °C/2000 h to 5000 h
EB series
TA series
105 °C
5000 h to 10000 h
125 °C
2000 h
FR series
FM series
HD series
105 °C
5000 h to 10000 h
105 °C
2000 h to 7000 h
105 °C
1000 h to 2000 h
FK series
FC series
NHG series
GA series (7L)
GA series Bi-polar
105 °C
3000 h to 5000 h
105 °C
1000 h to 5000 h
105 °C
1000 h to 2000 h
105 °C
1000 h
105 °C
1000 h to 2000 h
M series
SU series Bi-polar
85 °C
2000 h
85 °C
2000 h
KS/KA series
KS/KA series Bi-polar
85 °C
1000 h
85 °C
1000 h
Miniaturized
◼ Surface mount type
NEW
TCU series
High temperature · Long life
NEW
TC series
125 °C
3000 h
125 °C
2000 h to 3000 h
TQ series
TP series
TK series
TG series
125 °C
2000 h
125 °C
2000 h to 3000 h
125 °C
3000 h
125 °C
1000 h to 2000 h
Low impedance
HD series
105 °C
5000 h
Upgrade
FT series
NEW
FKS series
HC series
EB series (Large can)
105 °C
3000 h to 5000 h
105 °C
3000 h to 5000 h
HB series
HB series (5.4 L)
105 °C
2000 h
105 °C
2000 h
105 °C
2000 h to 5000 h
105 °C
2000 h
FP series
FK series
FC series
HA series
105 °C
2000 h
105 °C
2000 h to 5000 h
105 °C
1000 h
105 °C
1000 h
S series
85 °C
1000 h to 2000 h
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Lead taping radial lead type
● Dimensions
Lead space 2.5 mm 5.0 mm 7.5 mm
(F)
Figure Figure Figure
Case size (mm) 0D×L
4
× 5, 7
B
A
5
× 5, 7
B
A
6.3 × 5, 7
C
A
8
× 5, 7
C
E
5
× 11
C
D
6.3 × 11.2, 15
C
D
8
× 11.5, 15, 20
E
10 × 12.5, 16, 20, 25
F
12.5 × 15, 20, 25
G
16 × 15, 20, 25
H
18 × 15, 20, 25
H
Figure A
(Lead space: 5.0 mm / 0D×L : 04×5, 7, 05×5, 7, 06.3×5, 7)
12.7±1.0
fD
1.0 >
1.0 >
16.0±0.5
9.0±0.5
F
Dimensions
Nominal
Tolerance
0d
0.45
±0.05
F
5.0
+0.8
–0.2
P1
3.85
±0.50
Dimensions
Nominal
Tolerance
0d
0.45
±0.05
F
2.5
±0.5
P1
5.1
±0.5
17.50+0.75
–0.20
fd
P1
Unit : mm
0.6±0.3
6.0 < 0 to 1.5
18.0±0.5
L
6.35±1.0
f4.0±0.2
12.7±0.2
Figure B
(Lead space: 2.5 mm / 0D×L : 04×5, 7, 05×5, 7)
12.7±1.0
6.35±1.0
fD
1.0 >
1.0 >
9.0±0.5
F
04.0±0.2
0.6±0.3
0d
P1
18.50+0.75
–0.50
6.0 < 0 to 1.5
18.0±0.5
L
Unit : mm
12.7±0.2
Figure C
(Lead space: 2.5 mm / 0D×L : 05×11, 06.3×5, 7, 11.2, 15, 08×5, 7)
6.35±1.0
12.7±1.0
1.0 >
fD
1.0 >
f4.0±0.2
Nominal
Tolerance
0d
0.45 (5×11, 6.3×11.2, 15 : 0.50)
±0.05
F
2.5
±0.5
P1
5.1
±0.5
0.6±0.3
9.0±0.5
P1 F
18.50+0.75
–0.50
fd
6.0 <
18.0±0.5
0 to 1.5
L
Unit : mm
Dimensions
12.7±0.2
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
06
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
(Lead space: 5 mm / 0D×L : 05×11, 06.3×11.2, 15)
Figure D
12.7±1.0
1.0 > 1.0 >
fD
Nominal
Tolerance
0d
0.50
±0.05
F
5.0
+0.8
–0.2
P1
3.85
±0.50
0.6±0.3
9.0±0.5
F
16.0±0.5
fd
P1
Unit : mm
Dimensions
18.50+0.75
–0.50
6.0 < 0 to 1.5
18.0±0.5
L
6.35±1.0
f4.0±0.2
12.7±0.2
(Lead space: 5 mm / 0D×L : 08×5, 7, 11.5, 15, 20)
Figure E
12.7±1.0
fD
1.0 >
1.0 >
6.0 < 0 to 1.5
Unit : mm
Dimensions
0.6±0.3
F
H
P1
16.0±0.5
fd
9.0±0.5
18.0±0.5
L
6.35±1.0
f4.0±0.2
12.7±0.2
Nominal
08×11.5 to 20
08×5, 7
Suffix code
B
BQ
0d
0.60
0.45
Tolerance
±0.05
F
5.0
+0.8
–0.2
P1
3.85
±0.50
H
20.00
18.50
+0.75
–0.50
(Lead space: 5 mm / 0D×L : 010×12.5, 16, 20, 25)
Figure F
6.35±1.0
12.7±1.0
1.0 > 1.0 >
fD
f4.0±0.2
Dimensions
Nominal
Tolerance
0d
0.60
±0.05
F
5.0
P1
3.85
+0.8
–0.2
±0.50
0.6±0.3
9.0±0.5
P1 F
18.50+0.75
–0.50
fd
6.0 <
18.0±0.5
0 to 1.5
L
Unit : mm
12.7±0.2
Figure G
(Lead space: 5 mm / 0D×L : 012.5×15, 20, 25)
15.0±1.0
1.0 > 1.0 >
fD
f4.0±0.2
Unit : mm
Dimensions
Nominal
Tolerance
0d
0.60
±0.05
F
5.0
+0.8
–0.2
P1
5.0
±0.5
0.6±0.3
9.0±0.5
18.50+0.75
–0.50
fd
P1 F
6.0 <
18.0±0.5
0 to 1.5
L
7.5±1.0
15.0±0.2
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
06
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Figure H
7.5±1.0
1.3 >
30.0±1.0
fD
2.0 >
2.0 >
Unit : mm
Dimensions
Nominal
Tolerance
0d
0.80
±0.05
F
7.5
±0.5
P1
3.75
±0.50
15.0±0.2
0.6±0.3
F
18.50+0.75
–0.50
P1
fd
9.0±0.5
6.0 < 0 to 1.5
18.0±0.5
L
1.3 >
(Lead space: 7.5 mm / 0D×L : 016×15, 20, 25, 018×15, 20, 25)
f4.0±0.2
Packaging Specifications
Dimensions of outer carton box
b
c
Dimensions
a
Unit : mm
04 to 05
06.3
08
010, 012.5
016, 018
a
340 max.
340 max.
340 max.
340 max.
340 max.
b
to 55 max.
to 55 max.
to 55 max.
55 to 66 max.
62 to 75 max.
c
170 to 210 max.
270 max.
230 max.
170 to 270 max.
225 to 310 max.
2000 pcs.
2000 pcs.
1000 pcs.
500 pcs.
250 pcs.
Packaging Quantity
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
06
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Lead Forming Type (Snap-in)
Lead formed Aluminium Electrolytic Capacitor for self mounting, for rationalization and upgrade of soldering process.
0D
Dimensions
H3
H2
P
✽
H1
0d
E
F
4, 5, 6.3, 8
H1
H2
P
✽
0d
E
F
10, 12.5, 16, 18
✽ Direction of bending shape is not specified
Dimensions
Unit : mm
for PWB
0D
H1±0.5
H2
H3
F±0.5
P
E max.
0d
hole dia. 0
thickness
5
4.5
2.7
2.5
5.0
1.0
1.0
0.5
0.9
1.6
6.3
4.5
2.7
2.5
5.0
1.0
1.0
0.5
1.0
1.6
8
4.5
2.7
2.5
5.0
1.0
1.0
0.6
1.0
1.6
10
4.5
2.7
–
5.0
1.0
1.0
0.6
1.0
1.6
12.5
4.5
2.7
–
5.0
1.0 / 0.9
1.0
0.6 / 0.8
1.0 / 1.1
1.6
16
4.5
2.7
–
7.5
0.9
1.0
0.8
1.1
1.6
18
4.5
2.7
–
7.5
0.9
1.0
0.8
1.1
1.6
Series KA/KS Dimensions
Unit : mm
for PWB
0D
H1±0.5
H2
H3±0.3
F±0.5
P
E max.
0d
hole dia. 0
thickness
4
4.5
2.7
1.5
5.0
0.95
1.0
0.45
0.9
1.6
5
4.5
2.7
1.5
5.0
0.95
1.0
0.45
0.9
1.6
6.3
4.5
2.7
1.5
5.0
0.95
1.0
0.45
0.9
1.6
8
4.5
2.7
1.5
5.0
0.95
1.0
0.45
0.9
1.6
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
06
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : FC Type : A
Features
● Endurance
: 105 °C 1000 h to 5000 h
impedance
● RoHS compliant
● Low
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
Leakage current
Dissipation factor
(tan d)
Endurance
–55 °C to +105 °C
6.3 V.DC to 100 V.DC
2.2 µF to 15000 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV or 3 (µA) After 2 minutes (Whichever is greater)
V.DC
tan d
6.3
10
16
25
35
50
63
100
0.22
0.19
0.16
0.14
0.12
0.10
0.08
0.07
(120 Hz/+20 °C)
For capacitance value > 1000 µF, add 0.02 per every 1000 µF.
After following life test with DC voltage and +105 °C±2 °C ripple current value applied (The sum of DC
and ripple peak voltage shall not exceed the rated working voltage) when the capacitors are restored to
20 °C, the capacitors shall meet the limits specified bellow.
Duration : 04 to 06.3 : 1000 hours, 08 : 2000 hours , 010 : 3000 hours , 012.5 to 018 : 5000 hours
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
Shelf life
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
AEC-Q200
AEC-Q200 compliant
Frequency correction factor for ripple current
Rated voltage (V.DC)
Capacitance (µF)
2.2
390
1200
2700
6.3 to 100
60
0.55
0.70
0.75
0.80
to
330
to
1000
to
2200
to 15000
120
0.65
0.75
0.80
0.85
Frequency (Hz)
1k
0.85
0.90
0.90
0.95
10 k
0.90
0.95
0.95
1.00
100 k
1.00
1.00
1.00
1.00
fd±0.05
Dimensions
Sleeve
Pressure relief
06.3 <
< 08
010 <
+
L✽
14 min.
0D±0.5
3 min.
F±0.5
–
0D±0.5
✽ L < 16 : L±1.0 (✽08×15, 016×15, 018×15 : L±1.5)
L > 20 : L±2.0
0D
L
0d
F
4
5
6.3
8
L > 11
10
0.45
1.5
0.5
2.0
0.5
2.5
0.6
3.5
0.6
5.0
12.5
15 to 25 30 to 40
0.6
0.8
5.0
5.0
(Unit : mm)
16
18
4
L=7
5
6.3
0.8
7.5
0.8
7.5
0.45
1.5
0.45
2.0
0.45
2.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Case size/ Impedance/ Ripple current
Rated voltage
(V.DC)
Case size
(mm)
(0D×L)
6.3 V.DC to 35 V.DC
50 V.DC
100 V.DC
Ripple
Ripple
Ripple
Ripple
Impedance
Impedance
Impedance
current
current
current
current
(Ω)/(100 kHz)
(Ω)/(100 kHz)
(Ω)/(100 kHz)
(mA r.m.s)
(mA r.m.s)
(mA r.m.s)
(mA r.m.s)
20 °C –10 °C /(100 kHz) 20 °C –10 °C /(100 kHz) 20 °C –10 °C /(100 kHz) 20 °C –10 °C /(100 kHz)
Impedance
(Ω)/(100 kHz)
4
×
7
2.00
5.00
65
5
×
7
0.950
2.40
120
6.3 ×
7
0.450
1.20
200
× 11
0.800
1.60
175
6.3 × 11.2
0.350
0.700
290
✽
0.600
✽
1.20
8
× 11.5
0.117
0.234
555
0.234
8
× 15
0.085
0.170
730
0.155
5
63 V.DC
✽
260
2.00
4.00
145
4.10
8.20
80
1.00
2.00
240
1.80
3.60
114
0.468
485
0.342
0.684
405
0.680
1.36
260
0.310
635
0.230
0.460
535
0.450
0.900
340
× 20
0.065
0.130
995
0.120
0.240
860
0.178
0.356
690
0.330
0.660
455
10
× 12.5
0.090
0.180
755
0.162
0.324
615
0.256
0.512
535
0.530
1.06
306
10
× 16
0.068
0.136
1050
0.119
0.238
850
0.194
0.388
600
0.360
0.720
400
463
8
10
× 20
0.052
0.104
1220
0.090
0.180
1030
0.147
0.294
885
0.240
0.480
10
× 25
0.045
0.090
1440
0.082
0.164
1200
0.130
0.260
1050
0.210
0.420
599
10
× 30
0.035
0.070
1815
0.060
0.120
1610
0.090
0.180
1300
0.150
0.300
698
12.5 × 15
0.065
0.130
1205
0.110
0.220
1150
0.150
0.300
1020
0.230
0.460
511
12.5 × 20
0.038
0.076
1655
0.063
0.126
1480
0.085
0.170
1285
0.180
0.360
671
12.5 × 25
0.030
0.060
1945
0.050
0.100
1832
0.070
0.140
1720
0.110
0.220
807
12.5 × 30
0.025
0.050
2310
0.040
0.080
2215
0.055
0.110
2090
0.098
0.196
937
12.5 × 35
0.022
0.044
2510
0.034
0.068
2285
0.047
0.094
2265
0.087
0.174
1040
12.5 × 40
0.018
0.036
2655
0.030
0.060
2590
0.042
0.084
2560
0.072
0.144
1130
16
× 15
0.043
0.086
1690
0.080
0.160
1610
0.090
0.180
1410
0.140
0.280
793
16
× 20
0.029
0.058
2205
0.048
0.096
1835
0.059
0.118
1765
0.110
0.220
995
16
× 25
0.022
0.044
2555
0.034
0.068
2235
0.050
0.100
2160
0.089
0.178
1170
16
× 31.5
0.018
0.036
3010
0.028
0.056
2700
0.043
0.086
2670
0.062
0.124
1520
16
× 35.5
0.016
0.032
3150
0.025
0.050
2790
0.036
0.072
2770
0.053
0.106
1730
16
× 40
0.015
0.030
3360
0.023
0.046
2845
0.030
0.060
2825
0.047
0.094
1920
18
× 15
0.038
0.076
2000
0.068
0.136
1900
0.086
0.172
1690
0.120
0.240
917
1230
18
× 20
0.028
0.056
2490
0.042
0.084
2420
0.055
0.110
2290
0.080
0.160
18
× 25
0.020
0.040
2740
0.029
0.058
2610
0.043
0.086
2585
0.070
0.140
1420
18
× 31.5
0.016
0.032
3635
0.025
0.050
3000
0.032
0.064
2950
0.062
0.124
1600
18
× 35.5
0.015
0.030
3680
0.023
0.046
3100
0.030
0.060
3095
0.041
0.082
1770
18
× 40
0.014
0.028
3735
–
–
–
0.025
0.050
3205
0.036
0.072
2300
✽
Case size (mm)
(0D×L)
5 × 11
Capacitance
(µF)
1.0
2.2
3.3
4.7
10
12
15
18
22
Impedance (Ω)/(100 kHz)
20 °C
2.40
1.80
1.30
1.30
1.30
1.30
1.30
1.30
1.30
–10 °C
4.80
3.60
2.60
2.60
2.60
2.60
2.60
2.60
2.60
Ripple current
(mA r.m.s)(100 kHz)
20
45
65
95
125
135
145
155
155
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 04 to 06.3=1000 h, 08=2000 h, 010=3000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
27
56
100
120
220
270
330
390
470
560
820
1000
1200
1500
1800
6.3
2200
2700
3300
3900
4700
5600
6800
8200
10000
12000
15000
0D
4
5
5
6.3
6.3
6.3
6.3
8
8
8
8
10
10
8
10
10
12.5
10
10
16
10
12.5
16
12.5
18
12.5
12.5
16
12.5
16
12.5
16
18
16
16
18
16
18
18
Specification
Ripple
Impedance
current
Endurance
(100 kHz)
L
(100 kHz)
(hours)
(+20 °C)
(+105 °C)
(Ω)
(mA r.m.s.)
7
65 2.000 1000
7
120 0.950 1000
11
175 0.800 1000
7
200 0.450 1000
11.2
290 0.350 1000
11.2
290 0.350 1000
11.2
290 0.350 1000
11.5
555 0.117 2000
11.5
555 0.117 2000
11.5
555 0.117 2000
15
730 0.085 2000
12.5
755 0.090 3000
12.5
755 0.090 3000
20
995 0.065 2000
16
1050 0.068 3000
20
1220 0.052 3000
15
1205 0.065 5000
25
1440 0.045 3000
25
1440 0.045 3000
15
1690 0.043 5000
30
1815 0.035 3000
20
1655 0.038 5000
15
1690 0.043 5000
20
1655 0.038 5000
15
2000 0.038 5000
25
1945 0.030 5000
30
2310 0.025 5000
20
2205 0.029 5000
35
2510 0.022 5000
20
2205 0.029 5000
40
2655 0.018 5000
25
2555 0.022 5000
20
2490 0.028 5000
31.5
3010 0.018 5000
35.5
3150 0.016 5000
25
2740 0.020 5000
40
3360 0.015 5000
31.5
3635 0.016 5000
35.5
3680 0.015 5000
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
Taping Taping
0d Straight ✽B
✽H
0.45
0.45
0.50
0.45
0.50
0.50
0.50
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.80
0.60
0.60
0.80
0.60
0.80
0.60
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
1.5
2.0
2.0
2.5
2.5
2.5
2.5
3.5
3.5
3.5
3.5
5.0
5.0
3.5
5.0
5.0
5.0
5.0
5.0
7.5
5.0
5.0
7.5
5.0
7.5
5.0
5.0
7.5
5.0
7.5
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
7.5
7.5
7.5
7.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
Part No.
EEAFC0J270( )
EEAFC0J560( )
EEUFC0J101( )
EEAFC0J121( )
EEUFC0J221( )
EEUFC0J271( )
EEUFC0J331S( )
EEUFC0J391( )
EEUFC0J471( )
EEUFC0J561( )
EEUFC0J821L( )
EEUFC0J821( )
EEUFC0J102( )
EEUFC0J122L( )
EEUFC0J122( )
EEUFC0J152( )
EEUFC0J152S( )
EEUFC0J182( )
EEUFC0J222( )
EEUFC0J222S( )
EEUFC0J272L
EEUFC0J272( )
EEUFC0J272S( )
EEUFC0J332( )
EEUFC0J332S( )
EEUFC0J392( )
EEUFC0J472
EEUFC0J472S( )
EEUFC0J562L
EEUFC0J562( )
EEUFC0J682L
EEUFC0J682( )
EEUFC0J682S( )
EEUFC0J822
EEUFC0J103
EEUFC0J103S( )
EEUFC0J123L
EEUFC0J123
EEUFC0J153
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
200
100
200
100
200
100
100
100
100
100
100
100
100
100
100
100
50
50
2000
2000
2000
2000
2000
2000
2000
1000
1000
1000
1000
500
500
1000
500
500
500
500
500
250
500
250
500
250
500
250
250
250
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 04 to 06.3=1000 h, 08=2000 h, 010=3000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
22
39
82
100
150
180
220
330
390
470
560
680
820
1000
1200
10
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
10000
12000
0D
L
4
5
5
6.3
5
6.3
6.3
6.3
8
8
8
10
8
10
10
8
10
10
12.5
10
12.5
16
10
12.5
12.5
18
12.5
16
12.5
16
12.5
16
16
18
16
18
16
18
18
18
7
7
11
7
11
11.2
11.2
11.2
11.5
11.5
11.5
12.5
15
12.5
16
20
16
20
15
25
20
15
30
20
25
15
30
20
35
20
40
25
25
20
31.5
25
35.5
31.5
35.5
40
Specification
Ripple
Impedance
current
Endurance
(100 kHz)
(100 kHz)
(hours)
(+20 °C)
(+105 °C)
(Ω)
(mA r.m.s.)
65 2.000 1000
120 0.950 1000
175 0.800 1000
200 0.450 1000
175 0.800 1000
290 0.350 1000
290 0.350 1000
290 0.350 1000
555 0.117 2000
555 0.117 2000
555 0.117 2000
755 0.090 3000
730 0.085 2000
755 0.090 3000
1050 0.068 3000
995 0.065 2000
1050 0.068 3000
1220 0.052 3000
1205 0.065 5000
1440 0.045 3000
1655 0.038 5000
1690 0.043 5000
1815 0.035 3000
1655 0.038 5000
1945 0.030 5000
2000 0.038 5000
2310 0.025 5000
2205 0.029 5000
2510 0.022 5000
2205 0.029 5000
2655 0.018 5000
2555 0.022 5000
2555 0.022 5000
2490 0.028 5000
3010 0.018 5000
2740 0.020 5000
3150 0.016 5000
3635 0.016 5000
3680 0.015 5000
3735 0.014 5000
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
Taping Taping
0d Straight ✽B
✽H
0.45
0.45
0.50
0.45
0.50
0.50
0.50
0.50
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.80
0.60
0.60
0.60
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
1.5
2.0
2.0
2.5
2.0
2.5
2.5
2.5
3.5
3.5
3.5
5.0
3.5
5.0
5.0
3.5
5.0
5.0
5.0
5.0
5.0
7.5
5.0
5.0
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
Part No.
EEAFC1A220( )
EEAFC1A390( )
EEUFC1A820( )
EEAFC1A820( )
EEUFC1A101S( )
EEUFC1A151( )
EEUFC1A181( )
EEUFC1A221S( )
EEUFC1A331( )
EEUFC1A391( )
EEUFC1A471( )
EEUFC1A561( )
EEUFC1A681L( )
EEUFC1A681( )
EEUFC1A821( )
EEUFC1A102L( )
EEUFC1A102( )
EEUFC1A122( )
EEUFC1A122S( )
EEUFC1A152( )
EEUFC1A182( )
EEUFC1A182S( )
EEUFC1A222L
EEUFC1A222( )
EEUFC1A272( )
EEUFC1A272S( )
EEUFC1A332
EEUFC1A332S( )
EEUFC1A392L
EEUFC1A392( )
EEUFC1A472L
EEUFC1A472( )
EEUFC1A562( )
EEUFC1A562S( )
EEUFC1A682
EEUFC1A682S( )
EEUFC1A822L
EEUFC1A822
EEUFC1A103
EEUFC1A123
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
200
200
100
100
100
100
100
100
100
100
100
100
100
100
50
50
50
2000
2000
2000
2000
2000
2000
2000
2000
1000
1000
1000
500
1000
500
500
1000
500
500
500
500
500
250
500
500
250
250
250
250
250
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 04 to 06.3=1000 h, 08=2000 h, 010=3000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
15
27
47
56
68
100
120
220
270
330
390
470
560
680
820
1000
16
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
0D
L
4
5
5
5
6.3
5
6.3
6.3
8
8
8
10
8
10
10
8
10
10
12.5
10
10
10
16
10
12.5
16
12.5
18
12.5
16
12.5
16
12.5
18
16
18
16
18
16
18
16
18
7
7
11
11
7
11
11.2
11.2
11.5
11.5
11.5
12.5
15
12.5
16
20
16
20
15
20
25
25
15
30
20
15
25
15
25
20
30
20
35
20
25
20
31.5
25
35.5
31.5
40
35.5
Specification
Ripple
Impedance
current
Endurance
(100 kHz)
(100 kHz)
(hours)
(+20 °C)
(+105 °C)
(Ω)
(mA r.m.s.)
65 2.000 1000
120 0.950 1000
175 0.800 1000
175 0.800 1000
200 0.450 1000
175 0.800 1000
290 0.350 1000
290 0.350 1000
555 0.117 2000
555 0.117 2000
555 0.117 2000
755 0.090 3000
730 0.085 2000
755 0.090 3000
1050 0.068 3000
995 0.065 2000
1050 0.068 3000
1220 0.052 3000
1205 0.065 5000
1220 0.052 3000
1440 0.045 3000
1440 0.045 3000
1690 0.043 5000
1815 0.035 3000
1655 0.038 5000
1690 0.043 5000
1945 0.030 5000
2000 0.038 5000
1945 0.030 5000
2205 0.029 5000
2310 0.025 5000
2205 0.029 5000
2510 0.022 5000
2490 0.028 5000
2555 0.022 5000
2490 0.028 5000
3010 0.018 5000
2740 0.020 5000
3150 0.016 5000
3635 0.016 5000
3360 0.015 5000
3680 0.015 5000
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
Taping Taping
0d Straight ✽B
✽H
0.45
0.45
0.50
0.50
0.45
0.50
0.50
0.50
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.80
0.60
0.60
0.80
0.60
0.80
0.60
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
1.5
2.0
2.0
2.0
2.5
2.0
2.5
2.5
3.5
3.5
3.5
5.0
3.5
5.0
5.0
3.5
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
7.5
7.5
7.5
7.5
7.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
Part No.
EEAFC1C150( )
EEAFC1C270( )
EEUFC1C470( )
EEUFC1C560( )
EEAFC1C560( )
EEUFC1C680( )
EEUFC1C101( )
EEUFC1C121( )
EEUFC1C221( )
EEUFC1C271( )
EEUFC1C331( )
EEUFC1C391( )
EEUFC1C471L( )
EEUFC1C471( )
EEUFC1C561( )
EEUFC1C681L( )
EEUFC1C681( )
EEUFC1C821( )
EEUFC1C821S( )
EEUFC1C102S( )
EEUFC1C102( )
EEUFC1C122( )
EEUFC1C122S( )
EEUFC1C152L
EEUFC1C152( )
EEUFC1C152S( )
EEUFC1C182( )
EEUFC1C182S( )
EEUFC1C222( )
EEUFC1C222S( )
EEUFC1C272L
EEUFC1C272( )
EEUFC1C332
EEUFC1C332S( )
EEUFC1C392( )
EEUFC1C392S( )
EEUFC1C472
EEUFC1C472S( )
EEUFC1C562L
EEUFC1C562
EEUFC1C682
EEUFC1C822
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
200
100
200
100
200
100
100
100
100
100
100
100
100
100
100
50
100
50
2000
2000
2000
2000
2000
2000
2000
2000
1000
1000
1000
500
1000
500
500
1000
500
500
500
500
500
500
250
500
250
500
250
500
250
250
250
250
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 04 to 06.3=1000 h, 08=2000 h, 010=3000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
10
22
39
47
82
100
180
220
270
330
390
470
560
680
25
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
0D
L
4
5
5
6.3
5
6.3
6.3
8
8
10
8
10
10
8
10
10
12.5
10
10
12.5
10
12.5
16
12.5
18
12.5
16
12.5
16
12.5
18
16
16
18
16
18
18
18
7
7
11
7
11
11.2
11.2
11.5
11.5
12.5
15
12.5
16
20
16
20
15
20
25
20
30
20
15
25
15
25
20
30
20
35
20
25
31.5
25
35.5
31.5
35.5
40
Specification
Ripple
Impedance
current
Endurance
(100 kHz)
(100 kHz)
(hours)
(+20 °C)
(+105 °C)
(Ω)
(mA r.m.s.)
65 2.000 1000
120 0.950 1000
175 0.800 1000
200 0.450 1000
175 0.800 1000
290 0.350 1000
290 0.350 1000
555 0.117 2000
555 0.117 2000
755 0.090 3000
730 0.085 2000
755 0.090 3000
1050 0.068 3000
995 0.065 2000
1050 0.068 3000
1220 0.052 3000
1205 0.065 5000
1220 0.052 3000
1440 0.045 3000
1655 0.038 5000
1815 0.035 3000
1655 0.038 5000
1690 0.043 5000
1945 0.030 5000
2000 0.038 5000
1945 0.030 5000
2205 0.029 5000
2310 0.025 5000
2205 0.029 5000
2510 0.022 5000
2490 0.028 5000
2555 0.022 5000
3010 0.018 5000
2740 0.020 5000
3150 0.016 5000
3635 0.016 5000
3680 0.015 5000
3735 0.014 5000
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
Taping Taping
0d Straight ✽B
✽H
0.45
0.45
0.50
0.45
0.50
0.50
0.50
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.80
0.60
0.80
0.60
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
1.5
2.0
2.0
2.5
2.0
2.5
2.5
3.5
3.5
5.0
3.5
5.0
5.0
3.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
7.5
5.0
7.5
7.5
7.5
7.5
7.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
Part No.
EEAFC1E100( )
EEAFC1E220( )
EEUFC1E390( )
EEAFC1E390( )
EEUFC1E470( )
EEUFC1E820( )
EEUFC1E101S( )
EEUFC1E181( )
EEUFC1E221( )
EEUFC1E271( )
EEUFC1E331L( )
EEUFC1E331( )
EEUFC1E391( )
EEUFC1E471L( )
EEUFC1E471( )
EEUFC1E561( )
EEUFC1E561S( )
EEUFC1E681( )
EEUFC1E821( )
EEUFC1E821S( )
EEUFC1E102L
EEUFC1E102( )
EEUFC1E102S( )
EEUFC1E122( )
EEUFC1E122S( )
EEUFC1E152( )
EEUFC1E152S( )
EEUFC1E182L
EEUFC1E182( )
EEUFC1E222
EEUFC1E222S( )
EEUFC1E272( )
EEUFC1E332
EEUFC1E332S( )
EEUFC1E392L
EEUFC1E392
EEUFC1E472
EEUFC1E562
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
200
100
200
100
200
100
100
100
100
100
100
100
100
100
50
50
50
2000
2000
2000
2000
2000
2000
2000
1000
1000
500
1000
500
500
1000
500
500
500
500
500
500
500
250
500
250
500
250
250
250
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 04 to 06.3=1000 h, 08=2000 h, 010=3000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
6.8
12
22
27
33
47
56
68
100
120
150
180
220
270
330
390
470
35
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
0D
L
4
5
5
5
6.3
5
6.3
6.3
6.3
8
8
8
10
8
10
10
8
10
10
12.5
10
10
12.5
10
12.5
16
12.5
18
12.5
16
12.5
16
12.5
16
18
12.5
16
18
16
18
16
18
18
18
7
7
11
11
7
11
11.2
11.2
11.2
11.5
11.5
11.5
12.5
15
12.5
16
20
16
20
15
20
25
20
30
20
15
25
15
25
20
30
20
35
25
20
40
25
20
31.5
25
35.5
31.5
35.5
40
Specification
Ripple
Impedance
current
Endurance
(100 kHz)
(100 kHz)
(hours)
(+20 °C)
(+105 °C)
(Ω)
(mA r.m.s.)
65 2.000 1000
120 0.950 1000
175 0.800 1000
175 0.800 1000
200 0.450 1000
175 0.080 1000
290 0.350 1000
290 0.350 1000
290 0.350 1000
555 0.117 2000
555 0.117 2000
555 0.117 2000
755 0.090 3000
730 0.085 2000
755 0.090 3000
1050 0.068 3000
995 0.065 2000
1050 0.068 3000
1220 0.052 3000
1205 0.065 5000
1220 0.052 3000
1440 0.045 3000
1655 0.038 5000
1815 0.035 3000
1655 0.038 5000
1690 0.043 5000
1945 0.030 5000
2000 0.038 5000
1945 0.030 5000
2205 0.029 5000
2310 0.025 5000
2205 0.029 5000
2510 0.022 5000
2555 0.022 5000
2490 0.028 5000
2655 0.018 5000
2555 0.022 5000
2490 0.028 5000
3010 0.018 5000
2740 0.020 5000
3150 0.016 5000
3635 0.016 5000
3680 0.015 5000
3735 0.014 5000
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
Taping Taping
0d Straight ✽B
✽H
0.45
0.45
0.50
0.50
0.45
0.50
0.50
0.50
0.50
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.80
0.60
0.80
0.60
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
1.5
2.0
2.0
2.0
2.5
2.0
2.5
2.5
2.5
3.5
3.5
3.5
5.0
3.5
5.0
5.0
3.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
7.5
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
7.5
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
Part No.
EEAFC1V6R8( )
EEAFC1V120( )
EEUFC1V220( )
EEUFC1V270( )
EEAFC1V270( )
EEUFC1V330( )
EEUFC1V470( )
EEUFC1V560( )
EEUFC1V680( )
EEUFC1V101( )
EEUFC1V121( )
EEUFC1V151( )
EEUFC1V181( )
EEUFC1V221L( )
EEUFC1V221( )
EEUFC1V271( )
EEUFC1V331L( )
EEUFC1V331( )
EEUFC1V391( )
EEUFC1V391S( )
EEUFC1V471( )
EEUFC1V561( )
EEUFC1V561S( )
EEUFC1V681L
EEUFC1V681( )
EEUFC1V681S( )
EEUFC1V821L( )
EEUFC1V821( )
EEUFC1V102( )
EEUFC1V102S( )
EEUFC1V122L
EEUFC1V122( )
EEUFC1V152L
EEUFC1V152( )
EEUFC1V152S( )
EEUFC1V182L
EEUFC1V182( )
EEUFC1V182S( )
EEUFC1V222
EEUFC1V222S( )
EEUFC1V272L
EEUFC1V272
EEUFC1V332
EEUFC1V392
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
200
100
200
100
200
100
100
100
100
100
100
100
100
100
100
100
100
50
50
50
2000
2000
2000
2000
2000
2000
2000
2000
2000
1000
1000
1000
500
1000
500
500
1000
500
500
500
500
500
500
500
250
500
250
500
250
250
250
250
250
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 04 to 06.3=1000 h, 08=2000 h, 010=3000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
2.2
3.3
4.7
10
12
15
18
22
33
39
47
68
82
100
120
150
180
220
50
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
0D
L
5
5
5
5
5
5
5
5
6.3
6.3
6.3
8
8
10
8
10
10
8
10
10
12.5
10
10
12.5
12.5
16
10
12.5
12.5
18
12.5
16
12.5
18
12.5
16
16
18
16
16
18
18
11
11
11
11
11
11
11
11
11.2
11.2
11.2
11.5
11.5
12.5
15
12.5
16
20
16
20
15
25
30
20
20
15
30
25
25
15
30
20
35
20
40
25
31.5
25
35.5
40
31.5
35.5
Specification
Ripple
Impedance
current
Endurance
(100 kHz)
(100 kHz)
(hours)
(+20 °C)
(+105 °C)
(Ω)
(mA r.m.s.)
45 1.800 1000
65 1.300 1000
95 1.300 1000
125 1.300 1000
135 1.300 1000
145 1.300 1000
155 1.300 1000
155 1.300 1000
260 0.600 1000
260 0.600 1000
260 0.600 1000
485 0.234 2000
485 0.234 2000
615 0.162 3000
635 0.155 2000
615 0.162 3000
850 0.119 3000
860 0.120 2000
850 0.119 3000
1030 0.090 3000
1150 0.110 5000
1200 0.082 3000
1610 0.060 3000
1480 0.063 5000
1480 0.063 5000
1610 0.080 5000
1610 0.060 3000
1832 0.050 5000
1832 0.050 5000
1900 0.068 5000
2215 0.040 5000
1835 0.048 5000
2285 0.034 5000
2420 0.042 5000
2590 0.030 5000
2235 0.034 5000
2700 0.028 5000
2610 0.029 5000
2790 0.025 5000
2845 0.023 5000
3000 0.025 5000
3100 0.023 5000
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
Taping Taping
0d Straight ✽B
✽H
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.80
0.60
0.60
0.60
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.5
2.5
2.5
3.5
3.5
5.0
3.5
5.0
5.0
3.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
5.0
5.0
7.5
5.0
7.5
5.0
7.5
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
5.0
7.5
7.5
7.5
7.5
7.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
Part No.
EEUFC1H2R2( )
EEUFC1H3R3( )
EEUFC1H4R7( )
EEUFC1H100L( )
EEUFC1H120( )
EEUFC1H150( )
EEUFC1H180( )
EEUFC1H220( )
EEUFC1H330( )
EEUFC1H390( )
EEUFC1H470( )
EEUFC1H680( )
EEUFC1H820( )
EEUFC1H101( )
EEUFC1H121L( )
EEUFC1H121( )
EEUFC1H151( )
EEUFC1H181L( )
EEUFC1H181( )
EEUFC1H221( )
EEUFC1H221S( )
EEUFC1H271( )
EEUFC1H331L
EEUFC1H331( )
EEUFC1H391( )
EEUFC1H391S( )
EEUFC1H471L
EEUFC1H471( )
EEUFC1H561( )
EEUFC1H561S( )
EEUFC1H681L
EEUFC1H681( )
EEUFC1H821L
EEUFC1H821( )
EEUFC1H102L
EEUFC1H102( )
EEUFC1H122
EEUFC1H122S( )
EEUFC1H152L
EEUFC1H182L
EEUFC1H182
EEUFC1H222
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
200
200
100
100
200
200
100
100
100
100
100
100
100
100
100
100
100
50
50
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
1000
1000
500
1000
500
500
1000
500
500
500
500
500
500
250
500
500
250
250
250
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 04 to 06.3=1000 h, 08=2000 h, 010=3000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
12
22
33
47
56
68
82
100
120
150
180
220
270
63
330
390
470
560
680
820
1000
1200
1500
1800
0D
L
5
6.3
6.3
8
8
8
10
8
10
10
8
10
12.5
10
10
12.5
16
10
12.5
12.5
18
12.5
16
16
12.5
16
18
12.5
16
18
16
16
16
18
18
18
11
11.2
11.2
11.5
11.5
11.5
12.5
15
12.5
16
20
20
15
20
25
20
15
30
20
25
15
30
20
25
35
25
20
40
31.5
25
31.5
35.5
40
31.5
35.5
40
Specification
Ripple
Impedance
current
Endurance
(100 kHz)
(100 kHz)
(hours)
(+20 °C)
(+105 °C)
(Ω)
(mA r.m.s.)
145 2.000 1000
240 1.000 1000
240 1.000 1000
405 0.342 2000
405 0.342 2000
405 0.342 2000
535 0.256 3000
535 0.230 2000
535 0.256 3000
600 0.194 3000
690 0.178 2000
885 0.147 3000
1020 0.150 5000
885 0.147 3000
1050 0.130 3000
1285 0.085 5000
1410 0.090 5000
1300 0.090 3000
1285 0.085 5000
1720 0.070 5000
1690 0.086 5000
2090 0.055 5000
1765 0.059 5000
2160 0.050 5000
2265 0.047 5000
2160 0.050 5000
2290 0.055 5000
2560 0.042 5000
2670 0.043 5000
2585 0.043 5000
2670 0.043 5000
2770 0.036 5000
2825 0.030 5000
2950 0.032 5000
3095 0.030 5000
3205 0.025 5000
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
Taping Taping
0d Straight ✽B
✽H
0.50
0.50
0.50
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.80
0.60
0.60
0.60
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80
2.0
2.5
2.5
3.5
3.5
3.5
5.0
3.5
5.0
5.0
3.5
5.0
5.0
5.0
5.0
5.0
7.5
5.0
5.0
5.0
7.5
5.0
7.5
7.5
5.0
7.5
7.5
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
2.5
2.5
2.5
Part No.
Straight
Taping
leads
(pcs)
(pcs)
EEUFC1J120( )
EEUFC1J220( )
EEUFC1J330( )
EEUFC1J470( )
EEUFC1J560( )
EEUFC1J680( )
EEUFC1J820( )
EEUFC1J101L( )
EEUFC1J101( )
EEUFC1J121( )
EEUFC1J151( )
EEUFC1J181( )
EEUFC1J181S( )
EEUFC1J221X( )
EEUFC1J221( )
EEUFC1J221S( )
EEUFC1J271( )
EEUFC1J331L
EEUFC1J331( )
EEUFC1J391( )
EEUFC1J391S( )
EEUFC1J471L
EEUFC1J471( )
EEUFC1J561( )
EEUFC1J681L
EEUFC1J681( )
EEUFC1J681S( )
EEUFC1J821L
EEUFC1J821
EEUFC1J821S( )
EEUFC1J102U
EEUFC1J102
EEUFC1J122L
EEUFC1J122
EEUFC1J152
EEUFC1J182
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
200
200
100
100
100
100
100
100
100
100
100
100
100
100
100
50
50
50
2000
2000
2000
1000
1000
1000
500
1000
500
500
1000
500
500
500
500
500
250
500
500
250
250
250
250
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 04 to 06.3=1000 h, 08=2000 h, 010=3000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
5.6
12
22
33
39
56
68
100
120
100
150
180
220
270
330
390
470
560
680
0D
L
5
6.3
8
8
10
8
10
10
10
12.5
10
12.5
16
12.5
18
12.5
16
12.5
16
12.5
18
16
18
16
18
16
18
18
11
11.2
11.5
15
12.5
20
16
20
25
15
30
20
15
25
15
30
20
35
25
40
20
31.5
25
35.5
31.5
40
35.5
40
Specification
Lead length (mm)
Ripple
Lead space
Impedance
current
Endurance Lead
(100 kHz)
(100 kHz)
(hours) dia.
Taping Taping
(+20 °C)
(+105 °C)
0d Straight ✽B
✽H
(Ω)
(mA r.m.s.)
80 4.10
1000
0.5
2.0
5.0
2.5
114 1.80
1000
0.5
2.5
5.0
2.5
260 0.680 2000
0.6
3.5
5.0
340 0.450 2000
0.6
3.5
5.0
306 0.530 3000
0.6
5.0
5.0
455 0.330 2000
0.6
5.0
5.0
400 0.360 3000
0.6
5.0
5.0
463 0.240 3000
0.6
5.0
5.0
599 0.210 3000
0.6
5.0
5.0
511 0.230 5000
0.6
5.0
5.0
698 0.150 3000
0.6
5.0
671 0.180 5000
0.6
5.0
5.0
793 0.140 5000
0.8
7.5
7.5
807 0.110 5000
0.6
5.0
5.0
917 0.120 5000
0.8
7.5
7.5
937 0.098 5000
0.8
5.0
995 0.110 5000
0.8
7.5
7.5
1040 0.087 5000
0.8
5.0
1170 0.089 5000
0.8
7.5
7.5
1130 0.072 5000
0.8
5.0
1230 0.080 5000
0.8
7.5
7.5
1520 0.062 5000
0.8
7.5
1420 0.070 5000
0.8
7.5
7.5
1730 0.053 5000
0.8
7.5
1600 0.062 5000
0.8
7.5
1920 0.047 5000
0.8
7.5
1770 0.041 5000
0.8
7.5
2300 0.036 5000
0.8
7.5
Min. Packaging Q'ty
Part No.
EEUFC2A5R6( )
EEUFC2A120( )
EEUFC2A220( )
EEUFC2A330L( )
EEUFC2A330( )
EEUFC2A390L( )
EEUFC2A390( )
EEUFC2A560( )
EEUFC2A680L( )
EEUFC2A680( )
EEUFC2A101L
EEUFC2A101( )
EEUFC2A121S( )
EEUFC2A151( )
EEUFC2A151S( )
EEUFC2A181L
EEUFC2A181( )
EEUFC2A221L
EEUFC2A221( )
EEUFC2A271L
EEUFC2A271S( )
EEUFC2A331
EEUFC2A331S( )
EEUFC2A391L
EEUFC2A391
EEUFC2A471
EEUFC2A561
EEUFC2A681
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
100
200
100
200
100
100
100
100
100
100
100
100
100
100
50
100
50
50
2000
2000
1000
1000
500
1000
500
500
500
500
500
250
500
250
250
250
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
08
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : FK Type : A
Features
● Low
impedance (10 % to 30 % less than FC Series)
Miniaturization (30 % to 40 % less than FC Series)
● Endurance : 105 °C 3000 h to 5000 h
● RoHS compliant
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
Leakage current
V.DC
tan d
Dissipation factor
(tan d)
Endurance
–55 °C to +105 °C
6.3 V.DC to 35 V.DC
180 µF to 12000 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV (µA) After 2 minutes
6.3
10
16
25
35
0.22
0.19
0.16
0.14
0.12
(120 Hz/+20 °C)
Add 0.02 per 1000 µF for products of 1000 µF or more.
After following life test with DC voltage and +105 °C±2 °C ripple current value applied (The
sum of DC and ripple peak voltage shall not exceed the rated working voltage), when the
capacitors are restored to 20 °C, the capacitors shall meet the limits specified bellow.
Duration : 08: 3000 hours , 010: 4000 hours , 012.5 to 018: 5000 hours
Capacitance change
tan d
DC leakage current
Within ±20 % of the initial value
< 200 % of the initial limit
Within the initial limit
Shelf life
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
AEC-Q200
AEC-Q200 compliant
Frequency correction factor for ripple current
Rated voltage (V.DC)
6.3 to 35
Frequency (Hz)
Capacitance (µF)
60
120
1k
10 k
100 k
180
to
330
0.60
0.70
0.85
0.95
1.00
390
to
1000
0.65
0.75
0.90
0.98
1.00
to 12000
0.75
0.80
0.95
1.00
1.00
1200
Sleeve
Pressure relief
fd±0.05
Dimensions
08
010 <
+
L✽
14 min.
0D±0.5
3 min.
F±0.5
–
0D±0.5
✽ L < 16 : L±1.5
L > 20 : L±2.0
(Unit : mm)
0D
8
10
16
18
L
—
—
12.5 to 25
30 to 40
—
—
0d
0.6
0.6
0.6
0.8
0.8
0.8
F
3.5
5.0
5.0
5.0
7.5
7.5
12.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Case size/ Impedance/ Ripple current
Impedance
(Ω)/(100 kHz)
Case size (mm)
(0D×L)
8
8
8
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
12.5
16
16
16
18
18
18
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
11.5
15
20
12.5
16
20
25
30
15
20
25
30
35
40
15
20
25
15
20
25
Ripple current
(mA r.m.s.)/(100 kHz)
+20 °C
–10 °C
+105 °C
0.090
0.062
0.044
0.063
0.049
0.035
0.033
0.025
0.048
0.029
0.022
0.018
0.016
0.014
0.038
0.026
0.019
0.036
0.025
0.018
0.180
0.124
0.088
0.126
0.098
0.070
0.066
0.050
0.096
0.058
0.044
0.036
0.032
0.028
0.076
0.052
0.038
0.072
0.050
0.036
630
860
1220
900
1240
1490
1680
2140
1400
1890
2280
2720
2940
3010
1800
2330
2760
2060
2640
2850
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 08=3000 h, 010=4000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
680
1000
1500
1800
2200
6.3
3300
4700
5600
6800
8200
12000
560
820
1200
1500
1800
10
2700
3900
4700
5600
6800
8200
0D
L
8
8
10
8
10
12.5
10
10
10
12.5
16
12.5
18
12.5
16
12.5
12.5
16
18
18
8
8
10
8
10
12.5
10
10
10
12.5
16
12.5
18
12.5
16
12.5
12.5
16
18
18
11.5
15
12.5
20
16
15
20
25
30
20
15
25
15
30
20
35
40
25
20
25
11.5
15
12.5
20
16
15
20
25
30
20
15
25
15
30
20
35
40
25
20
25
Specification
Lead length (mm)
Ripple
Lead space
Impedance
current
Endurance Lead
(100 kHz)
(100 kHz)
(hours) dia.
Taping
(+20 °C)
Straight
(+105 °C)
0d
✽B
(Ω)
(mA r.m.s.)
630 0.090 3000
0.6
3.5
5.0
860 0.062 3000
0.6
3.5
5.0
900 0.063 4000
0.6
5.0
5.0
1220 0.044 3000
0.6
3.5
5.0
1240 0.049 4000
0.6
5.0
5.0
1400 0.048 5000
0.6
5.0
5.0
1490 0.035 4000
0.6
5.0
5.0
1680 0.033 4000
0.6
5.0
5.0
2140 0.025 4000
0.6
5.0
1890 0.029 5000
0.6
5.0
5.0
1800 0.038 5000
0.8
7.5
7.5
2280 0.022 5000
0.6
5.0
5.0
2060 0.036 5000
0.8
7.5
7.5
2720 0.018
5000
0.8
5.0
2330 0.026 5000
0.8
7.5
7.5
2940 0.016
5000
0.8
5.0
3010 0.014
5000
0.8
5.0
2760 0.019
5000
0.8
7.5
7.5
2640 0.025 5000
0.8
7.5
7.5
2850 0.018
5000
0.8
7.5
7.5
630 0.090 3000
0.6
3.5
5.0
860 0.062 3000
0.6
3.5
5.0
900 0.063 4000
0.6
5.0
5.0
1220 0.044 3000
0.6
3.5
5.0
1240 0.049 4000
0.6
5.0
5.0
1400 0.048 5000
0.6
5.0
5.0
1490 0.035 4000
0.6
5.0
5.0
1680 0.033 4000
0.6
5.0
5.0
2140 0.025 4000
0.6
5.0
1890 0.029 5000
0.6
5.0
5.0
1800 0.038 5000
0.8
7.5
7.5
2280 0.022 5000
0.6
5.0
5.0
2060 0.036 5000
0.8
7.5
7.5
2720 0.018
5000
0.8
5.0
2330 0.026 5000
0.8
7.5
7.5
2940 0.016
5000
0.8
5.0
3010 0.014
5000
0.8
5.0
2760 0.019
5000
0.8
7.5
7.5
2640 0.025 5000
0.8
7.5
7.5
2850 0.018
5000
0.8
7.5
7.5
Min. Packaging Q'ty
Part No.
EEUFK0J681( )
EEUFK0J102L( )
EEUFK0J102( )
EEUFK0J152L( )
EEUFK0J152( )
EEUFK0J182S( )
EEUFK0J222( )
EEUFK0J222L( )
EEUFK0J332L
EEUFK0J332( )
EEUFK0J332S( )
EEUFK0J472( )
EEUFK0J472S( )
EEUFK0J562L
EEUFK0J562S( )
EEUFK0J682L
EEUFK0J822L
EEUFK0J822( )
EEUFK0J822S( )
EEUFK0J123S( )
EEUFK1A561( )
EEUFK1A821L( )
EEUFK1A821( )
EEUFK1A122L( )
EEUFK1A122( )
EEUFK1A152S( )
EEUFK1A182( )
EEUFK1A182L( )
EEUFK1A272L
EEUFK1A272( )
EEUFK1A272S( )
EEUFK1A392( )
EEUFK1A392S( )
EEUFK1A472L
EEUFK1A472S( )
EEUFK1A562L
EEUFK1A682L
EEUFK1A682( )
EEUFK1A682S( )
EEUFK1A822S( )
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
100
200
100
200
100
100
100
100
100
100
100
100
200
200
200
200
200
200
200
200
100
200
100
200
100
100
100
100
100
100
100
100
1000
1000
500
1000
500
500
500
500
500
250
500
250
250
250
250
250
1000
1000
500
1000
500
500
500
500
500
250
500
250
250
250
250
250
· When requesting taped product, please put the letter "B" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 08=3000 h, 010=4000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
390
680
820
1000
1200
1500
16
2200
2700
3300
3900
4700
5600
6800
270
390
470
560
820
1000
1200
25
1500
1800
2200
2700
3300
4700
0D
L
8
8
10
8
10
10
12.5
10
10
12.5
16
12.5
18
12.5
12.5
16
12.5
18
16
18
8
8
10
8
10
10
12.5
10
12.5
10
16
12.5
18
12.5
16
12.5
12.5
16
18
18
11.5
15
12.5
20
16
20
15
25
30
20
15
25
15
30
35
20
40
20
25
25
11.5
15
12.5
20
16
20
15
25
20
30
15
25
15
30
20
35
40
25
20
25
Specification
Lead length (mm)
Ripple
Lead space
Impedance
current
Endurance Lead
(100 kHz)
(100 kHz)
(hours) dia.
Taping
(+20 °C)
Straight
(+105 °C)
0d
✽B
(Ω)
(mA r.m.s.)
630 0.090 3000
0.6
3.5
5.0
860 0.062 3000
0.6
3.5
5.0
900 0.063 4000
0.6
5.0
5.0
1220 0.044 3000
0.6
3.5
5.0
1240 0.049 4000
0.6
5.0
5.0
1490 0.035 4000
0.6
5.0
5.0
1400 0.048 5000
0.6
5.0
5.0
1680 0.033 4000
0.6
5.0
5.0
2140 0.025 4000
0.6
5.0
1890 0.029 5000
0.6
5.0
5.0
1800 0.038 5000
0.8
7.5
7.5
2280 0.022 5000
0.6
5.0
5.0
2060 0.036 5000
0.8
7.5
7.5
2720 0.018
5000
0.8
5.0
2940 0.016
5000
0.8
5.0
2330 0.026 5000
0.8
7.5
7.5
3010 0.014
5000
0.8
5.0
2640 0.025 5000
0.8
7.5
7.5
2760 0.019
5000
0.8
7.5
7.5
2850 0.018
5000
0.8
7.5
7.5
630 0.090 3000
0.6
3.5
5.0
860 0.062 3000
0.6
3.5
5.0
900 0.063 4000
0.6
5.0
5.0
1220 0.044 3000
0.6
3.5
5.0
1240 0.049 4000
0.6
5.0
5.0
1490 0.035 4000
0.6
5.0
5.0
1400 0.048 5000
0.6
5.0
5.0
1680 0.033 4000
0.6
5.0
5.0
1890 0.029 5000
0.6
5.0
5.0
2140 0.025 4000
0.6
5.0
1800 0.038 5000
0.8
7.5
7.5
2280 0.022 5000
0.6
5.0
5.0
2060 0.036 5000
0.8
7.5
7.5
2720 0.018
5000
0.8
5.0
2330 0.026 5000
0.8
7.5
7.5
2940 0.016
5000
0.8
5.0
3010 0.014
5000
0.8
5.0
2760 0.019
5000
0.8
7.5
7.5
2640 0.025 5000
0.8
7.5
7.5
2850 0.018
5000
0.8
7.5
7.5
Min. Packaging Q'ty
Part No.
EEUFK1C391( )
EEUFK1C681L( )
EEUFK1C681( )
EEUFK1C821L( )
EEUFK1C102( )
EEUFK1C122( )
EEUFK1C122S( )
EEUFK1C152L( )
EEUFK1C222L
EEUFK1C222( )
EEUFK1C222S( )
EEUFK1C272( )
EEUFK1C272S( )
EEUFK1C332L
EEUFK1C392L
EEUFK1C392S( )
EEUFK1C472L
EEUFK1C472S( )
EEUFK1C562( )
EEUFK1C682S( )
EEUFK1E271( )
EEUFK1E391L( )
EEUFK1E471( )
EEUFK1E561L( )
EEUFK1E561( )
EEUFK1E821( )
EEUFK1E821S( )
EEUFK1E102L( )
EEUFK1E122( )
EEUFK1E152L
EEUFK1E152S( )
EEUFK1E182( )
EEUFK1E182S( )
EEUFK1E222L
EEUFK1E222S( )
EEUFK1E272L
EEUFK1E332L
EEUFK1E332( )
EEUFK1E332S( )
EEUFK1E472S( )
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
100
200
100
200
100
100
100
100
100
100
100
100
200
200
200
200
200
200
200
200
200
100
100
200
100
100
100
100
100
100
100
100
1000
1000
500
1000
500
500
500
500
500
250
500
250
250
250
250
250
1000
1000
500
1000
500
500
500
500
500
250
500
250
250
250
250
250
· When requesting taped product, please put the letter "B" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 08=3000 h, 010=4000 h, 012.5 to 018=5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
180
270
390
560
680
820
35
1000
1200
1500
1800
2200
3300
0D
L
8
8
10
8
10
10
12.5
10
12.5
10
16
12.5
18
12.5
12.5
16
12.5
16
18
18
11.5
15
12.5
20
16
20
15
25
20
30
15
25
15
30
35
20
40
25
20
25
Specification
Lead length (mm)
Ripple
Lead space
Impedance
current
Endurance Lead
(100 kHz)
(100 kHz)
(hours) dia.
Taping
(+20 °C)
Straight
(+105 °C)
0d
✽B
(Ω)
(mA r.m.s.)
630 0.090 3000
0.6
3.5
5.0
860 0.062 3000
0.6
3.5
5.0
900 0.063 4000
0.6
5.0
5.0
1220 0.044 3000
0.6
3.5
5.0
1240 0.049 4000
0.6
5.0
5.0
1490 0.035 4000
0.6
5.0
5.0
1400 0.048 5000
0.6
5.0
5.0
1680 0.033 4000
0.6
5.0
5.0
1890 0.029 5000
0.6
5.0
5.0
2140 0.025 4000
0.6
5.0
1800 0.038 5000
0.8
7.5
7.5
2280 0.022 5000
0.6
5.0
5.0
2060 0.036 5000
0.8
7.5
7.5
2720 0.018
5000
0.8
5.0
2940 0.016
5000
0.8
5.0
2330 0.026 5000
0.8
7.5
7.5
3010 0.014
5000
0.8
5.0
2760 0.019
5000
0.8
7.5
7.5
2640 0.025 5000
0.8
7.5
7.5
2850 0.018
5000
0.8
7.5
7.5
Min. Packaging Q'ty
Part No.
EEUFK1V181( )
EEUFK1V271L( )
EEUFK1V271( )
EEUFK1V391L( )
EEUFK1V391( )
EEUFK1V561( )
EEUFK1V561S( )
EEUFK1V681L( )
EEUFK1V821( )
EEUFK1V102L
EEUFK1V102S( )
EEUFK1V122( )
EEUFK1V122S( )
EEUFK1V152L
EEUFK1V182L
EEUFK1V182S( )
EEUFK1V222L
EEUFK1V222( )
EEUFK1V222S( )
EEUFK1V332S( )
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
100
100
200
100
100
100
100
100
100
100
100
1000
1000
500
1000
500
500
500
500
500
250
500
250
250
250
250
250
· When requesting taped product, please put the letter "B" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : FM Type : A
Features
● Low impedance (40 % to 70 % less than
● Endurance : 105 °C 2000 h to 7000 h
● RoHS compliant
FC Series)
Attention
● Not applicable for automotive
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
Leakage current
Dissipation factor
(tan d)
Endurance
Shelf life
–40 °C to +105 °C
6.3 V.DC to 50 V.DC
22 µF to 6800 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV (µA) After 2 minutes
V.DC
6.3
10
16
25
35
50
(max.) (120 Hz/+20 °C)
tan d
0.22 0.19 0.16 0.14 0.12 0.10
Add 0.02 per 1000 µF for products of 1000 µF or more.
After following life test with DC voltage and +105 °C±2 °C ripple current value applied. (The
sum of DC and ripple peak voltage shall not exceed the rated working voltage) when the
capacitors are restored to 20 °C, the capacitors shall meet the limits specified below.
Duration
05 to 06.3 : 2000 hours, 08×11.5 to 08×15: 3000 hours
08×20 to 010×16 : 4000 hours, 010×20 to 012.5×20/ 016×20 : 5000 hours
012.5×25 to 012.5×35/ 016×25 : 7000 hours
Capacitance change Within ±25 % of the initial value (6.3 V.DC to 10 V.DC : ±30 %)
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Frequency correction factor for ripple current
Rated voltage (V.DC)
6.3 to 50
Capacitance (µF)
22
47
390
1200
to
to
to
to
60
0.45
0.60
0.65
0.75
33
330
1000
6800
Frequency (Hz)
1k
0.75
0.85
0.90
0.95
120
0.55
0.70
0.75
0.80
10 k
0.90
0.95
0.98
1.00
100 k
1.00
1.00
1.00
1.00
fd±0.05
Dimensions
Sleeve
Pressure relief
06.3 <
< 08
010 <
+
L✽
✽
0D
L
0d
F
14 min.
0D±0.5
3 min.
F±0.5
–
0D±0.5
L < 16 : L±1.5
L > 20 : L±2.0
5
—
0.5
2.0
(Unit : mm)
6.3
—
0.5
2.5
8
—
0.6
3.5
10
—
0.6
5.0
12.5
12.5 to 25 30 to 40
0.6
0.8
5.0
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
16
—
0.8
7.5
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Case size/ Impedance/ Ripple current
Rated voltage
(V.DC)
Case size
(mm)
(0D×L)
5
× 11
6.3 V.DC to 35 V.DC
Impedance
(Ω/100 kHz)
+20 °C
–10 °C
50 V.DC
Ripple current
(mA r.m.s./100 kHz)
+105 °C
Impedance
(Ω/100 kHz)
+20 °C
–10 °C
Ripple current
(mA r.m.s./100 kHz)
+105 °C
0.300
1.000
280
0.340
1.130
250
6.3 × 11.2
0.130
0.430
455
0.140
0.460
405
8
× 11.5
0.056
0.168
950
0.061
0.183
870
8
× 15
0.041
0.123
1240
0.045
0.135
1140
8
× 20
0.030
0.090
1560
0.033
0.099
1430
10
× 12.5
0.038
0.114
1290
0.042
0.126
1170
10
× 16
0.026
0.078
1790
0.030
0.090
1650
10
× 20
0.019
0.057
2180
0.023
0.069
1890
10
× 25
0.018
0.054
2470
0.022
0.066
2150
12.5 × 20
0.018
0.045
2600
0.022
0.055
2260
12.5 × 25
0.015
0.038
3190
0.018
0.045
2660
12.5 × 30
0.013
0.033
3630
0.016
0.040
3160
12.5 × 35
0.012
0.030
3750
0.014
0.035
3270
16
× 20
0.017
0.043
3300
0.019
0.048
2870
16
× 25
0.014
0.035
3820
0.016
0.040
3320
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
150
330
560
820
1000
1200
6.3
1500
2200
3300
3900
4700
5600
6800
100
220
470
680
1000
10
1200
1500
2200
3300
3900
4700
5600
68
120
330
470
680
16
1000
1200
1500
2200
2700
3300
3900
0D
5
6.3
8
8
10
8
10
10
10
12.5
12.5
12.5
12.5
16
16
5
6.3
8
8
10
8
10
10
10
12.5
12.5
12.5
16
12.5
16
5
6.3
8
8
10
8
10
10
10
12.5
12.5
12.5
16
12.5
16
Specification
Lead length (mm)
Ripple
Lead space
Impedance
current
Endurance Lead
(100 kHz)
(100 kHz)
(hours) dia.
L
Taping Taping
(+20 °C)
(+105 °C)
0d Straight ✽B
✽H
(Ω)
(mA r.m.s.)
11
280 0.300 2000
0.5
2.0
5.0
2.5
11.2
455 0.130 2000
0.5
2.5
5.0
2.5
11.5
950 0.056 3000
0.6
3.5
5.0
15
1240 0.041 3000
0.6
3.5
5.0
12.5
1290 0.038 4000
0.6
5.0
5.0
20
1560 0.030 4000
0.6
3.5
5.0
16
1790 0.026 4000
0.6
5.0
5.0
20
2180 0.019 5000
0.6
5.0
5.0
25
2470 0.018 5000
0.6
5.0
5.0
20
2600 0.018 5000
0.6
5.0
5.0
25
3190 0.015 7000
0.6
5.0
5.0
30
3630 0.013 7000
0.8
5.0
35
3750 0.012 7000
0.8
5.0
20
3300 0.017 5000
0.8
7.5
7.5
25
3820 0.014 7000
0.8
7.5
7.5
11
280 0.300 2000
0.5
2.0
5.0
2.5
11.2
455 0.130 2000
0.5
2.5
5.0
2.5
11.5
950 0.056 3000
0.6
3.5
5.0
15
1240 0.041 3000
0.6
3.5
5.0
12.5
1290 0.038 4000
0.6
5.0
5.0
20
1560 0.030 4000
0.6
3.5
5.0
16
1790 0.026 4000
0.6
5.0
5.0
20
2180 0.019 5000
0.6
5.0
5.0
25
2470 0.018 5000
0.6
5.0
5.0
20
2600 0.018 5000
0.6
5.0
5.0
25
3190 0.015 7000
0.6
5.0
5.0
30
3630 0.013 7000
0.8
5.0
20
3300 0.017 5000
0.8
7.5
7.5
35
3750 0.012 7000
0.8
5.0
25
3820 0.014 7000
0.8
7.5
7.5
11
280 0.300 2000
0.5
2.0
5.0
2.5
11.2
455 0.130 2000
0.5
2.5
5.0
2.5
11.5
950 0.056 3000
0.6
3.5
5.0
15
1240 0.041 3000
0.6
3.5
5.0
12.5
1290 0.038 4000
0.6
5.0
5.0
20
1560 0.030 4000
0.6
3.5
5.0
16
1790 0.026 4000
0.6
5.0
5.0
20
2180 0.019 5000
0.6
5.0
5.0
25
2470 0.018 5000
0.6
5.0
5.0
20
2600 0.018 5000
0.6
5.0
5.0
25
3190 0.015 7000
0.6
5.0
5.0
30
3630 0.013 7000
0.8
5.0
20
3300 0.017 5000
0.8
7.5
7.5
35
3750 0.012 7000
0.8
5.0
25
3820 0.014 7000
0.8
7.5
7.5
Min. Packaging Q'ty
Part No.
EEUFM0J151( )
EEUFM0J331( )
EEUFM0J561( )
EEUFM0J821L( )
EEUFM0J102( )
EEUFM0J122L( )
EEUFM0J122( )
EEUFM0J152( )
EEUFM0J222L( )
EEUFM0J332( )
EEUFM0J392( )
EEUFM0J472L
EEUFM0J562L
EEUFM0J562S( )
EEUFM0J682( )
EEUFM1A101( )
EEUFM1A221( )
EEUFM1A471( )
EEUFM1A681L( )
EEUFM1A681( )
EEUFM1A102L( )
EEUFM1A102( )
EEUFM1A122( )
EEUFM1A152L( )
EEUFM1A222( )
EEUFM1A332( )
EEUFM1A392L
EEUFM1A392S( )
EEUFM1A472L
EEUFM1A562( )
EEUFM1C680( )
EEUFM1C121( )
EEUFM1C331( )
EEUFM1C471L( )
EEUFM1C471( )
EEUFM1C681L( )
EEUFM1C681( )
EEUFM1C102( )
EEUFM1C122L( )
EEUFM1C152( )
EEUFM1C222( )
EEUFM1C272L
EEUFM1C272S( )
EEUFM1C332L
EEUFM1C392( )
Long
Taping
lead
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
2000
2000
1000
1000
500
1000
500
500
500
500
500
250
250
2000
2000
1000
1000
500
1000
500
500
500
500
500
250
250
2000
2000
1000
1000
500
1000
500
500
500
500
500
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
47
100
220
330
470
25
680
820
1000
1500
1800
2200
2700
33
68
150
220
330
35
470
560
680
1000
1200
50
1500
1800
22
56
100
120
150
180
220
270
330
470
560
680
820
1000
0D
5
6.3
8
8
10
8
10
10
10
12.5
12.5
12.5
16
12.5
16
5
6.3
8
8
10
8
10
10
10
12.5
12.5
12.5
16
12.5
16
5
6.3
8
8
10
8
10
10
10
12.5
12.5
12.5
12.5
16
16
Specification
Lead length (mm)
Ripple
Lead space
Impedance
current
Endurance Lead
(100 kHz)
(100 kHz)
(hours) dia.
L
Taping Taping
(+20 °C)
(+105 °C)
0d Straight ✽B
✽H
(Ω)
(mA r.m.s.)
11
280 0.300 2000
0.5
2.0
5.0
2.5
11.2
455 0.130 2000
0.5
2.5
5.0
2.5
11.5
950 0.056 3000
0.6
3.5
5.0
15
1240 0.041 3000
0.6
3.5
5.0
12.5
1290 0.038 4000
0.6
5.0
5.0
20
1560 0.030 4000
0.6
3.5
5.0
16
1790 0.026 4000
0.6
5.0
5.0
20
2180 0.019 5000
0.6
5.0
5.0
25
2470 0.018 5000
0.6
5.0
5.0
20
2600 0.018 5000
0.6
5.0
5.0
25
3190 0.015 7000
0.6
5.0
5.0
30
3630 0.013 7000
0.8
5.0
20
3300 0.017 5000
0.8
7.5
7.5
35
3750 0.012 7000
0.8
5.0
25
3820 0.014 7000
0.8
7.5
7.5
11
280 0.300 2000
0.5
2.0
5.0
2.5
11.2
455 0.130 2000
0.5
2.5
5.0
2.5
11.5
950 0.056 3000
0.6
3.5
5.0
15
1240 0.041 3000
0.6
3.5
5.0
12.5
1290 0.038 4000
0.6
5.0
5.0
20
1560 0.030 4000
0.6
3.5
5.0
16
1790 0.026 4000
0.6
5.0
5.0
20
2180 0.019 5000
0.6
5.0
5.0
25
2470 0.018 5000
0.6
5.0
5.0
20
2600 0.018 5000
0.6
5.0
5.0
25
3190 0.015 7000
0.6
5.0
5.0
30
3630 0.013 7000
0.8
5.0
20
3300 0.017 5000
0.8
7.5
7.5
35
3750 0.012 7000
0.8
5.0
25
3820 0.014 7000
0.8
7.5
7.5
11
250 0.340 2000
0.5
2.0
5.0
2.5
11.2
405 0.140 2000
0.5
2.5
5.0
2.5
11.5
870 0.061 3000
0.6
3.5
5.0
15
1140 0.045 3000
0.6
3.5
5.0
12.5
1170 0.042 4000
0.6
5.0
5.0
20
1430 0.033 4000
0.6
3.5
5.0
16
1650 0.030 4000
0.6
5.0
5.0
20
1890 0.023 5000
0.6
5.0
5.0
25
2150 0.022 5000
0.6
5.0
5.0
20
2260 0.022 5000
0.6
5.0
5.0
25
2660 0.018 7000
0.6
5.0
5.0
30
3160 0.016 7000
0.8
5.0
35
3270 0.014 7000
0.8
5.0
20
2870 0.019 5000
0.8
7.5
7.5
25
3320 0.016 7000
0.8
7.5
7.5
Min. Packaging Q'ty
Part No.
EEUFM1E470( )
EEUFM1E101( )
EEUFM1E221( )
EEUFM1E331L( )
EEUFM1E331( )
EEUFM1E471L( )
EEUFM1E471( )
EEUFM1E681( )
EEUFM1E821L( )
EEUFM1E102( )
EEUFM1E152( )
EEUFM1E182L
EEUFM1E182S( )
EEUFM1E222L
EEUFM1E272( )
EEUFM1V330( )
EEUFM1V680( )
EEUFM1V151( )
EEUFM1V221L( )
EEUFM1V221( )
EEUFM1V331L( )
EEUFM1V331( )
EEUFM1V471( )
EEUFM1V561L( )
EEUFM1V681( )
EEUFM1V102( )
EEUFM1V122L
EEUFM1V122S( )
EEUFM1V152L
EEUFM1V182( )
EEUFM1H220( )
EEUFM1H560( )
EEUFM1H101( )
EEUFM1H121L( )
EEUFM1H151( )
EEUFM1H181L( )
EEUFM1H221( )
EEUFM1H271( )
EEUFM1H331L( )
EEUFM1H471( )
EEUFM1H561( )
EEUFM1H681L
EEUFM1H821L
EEUFM1H821S( )
EEUFM1H102( )
Long
Taping
lead
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
2000
2000
1000
1000
500
1000
500
500
500
500
500
250
250
2000
2000
1000
1000
500
1000
500
500
500
500
500
250
250
2000
2000
1000
1000
500
1000
500
500
500
500
500
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : FR Type : A
Features
Country of origin
● Low ESR (Same as FM Series)
● Endurance : 105 °C 5000 h to 10000
● RoHS compliant
● Malaysia
h
Attention
● Not applicable for automotive
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
Leakage current
Dissipation factor
(tan d)
Endurance
Shelf life
–40 °C to +105 °C
6.3 V.DC to 100 V.DC
4.7 µF to 8200 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV (µA) After 2 minutes
V.DC
6.3
10
16
25
35
50
63
100
(120 Hz/+20 °C)
tan d
0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08
Add 0.02 per 1000 µF for products of 1000 µF or more.
After following life test with DC voltage and +105 °C±2 °C ripple current value applied. (The sum
of DC and ripple peak voltage shall not exceed the rated working voltage) when the capacitors
are restored to 20 °C, the capacitors shall meet the limits specified below.
Duration
05×11/ 06.3×11.2 : 5000 hours
08×11.5/ 010×12.5 : 6000 hours (✽ Only EEUFR1V331U (010×12.5) 5000 hours)
08×15/ 010×16 : 8000 hours, 08×20 : 9000 hours
010×20 to 010×25/ 012.5×20 to 012.5×35/ 016×20 to 016×25 : 10000 hours
Capacitance change Within ±25 % of the initial value (6.3 V.DC to 10 V.DC : ±30 %)
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Frequency correction factor for ripple current
Rated voltage (V.DC)
6.3 to 100
Capacitance (µF)
4.7
47
390
1200
to
to
to
to
60
0.45
0.60
0.65
0.75
33
330
1000
8200
Frequency (Hz)
1k
0.75
0.85
0.90
0.95
120
0.55
0.70
0.75
0.80
10 k
0.90
0.95
0.98
1.00
100 k
1.00
1.00
1.00
1.00
Sleeve
Pressure relief
06.3 <
fd±0.05
Dimensions
< 08
010 <
+
L✽
✽
0D
L
0d
F
14 min.
0D±0.5
3 min.
F±0.5
–
0D±0.5
L < 16 : L±1.5
L > 20 : L±2.0
5
—
0.5
2.0
(Unit : mm)
6.3
—
0.5
2.5
8
—
0.6
3.5
10
—
0.6
5.0
12.5
12.5 to 25
30 to 35
0.6
0.8
5.0
16
—
0.8
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
07
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Case size/ Impedance/ Ripple current
Rated voltage
(V.DC)
Case size
(mm)
(0D×L)
5
× 11
6.3 V.DC to 35 V.DC
Impedance
(Ω/100 kHz)
+20 °C
–10 °C
50 V.DC
Ripple current
(mA r.m.s./100 kHz)
+105 °C
Impedance
(Ω/100 kHz)
+20 °C
–10 °C
Ripple current
(mA r.m.s./100 kHz)
+105 °C
0.300
1.000
280
0.340
1.130
250
6.3 × 11.2
0.130
0.430
455
0.140
0.460
405
8
× 11.5
0.056
0.168
950
0.061
0.183
870
8
× 15
0.041
0.123
1240
0.045
0.135
1140
8
× 20
0.030
0.090
1560
0.033
0.099
1430
10
× 12.5
0.043
0.114
1290
0.042
0.126
1170
10
× 16
0.028
0.078
1790
0.030
0.090
1650
10
× 20
0.020
0.057
2180
0.023
0.069
1890
10
× 25
0.018
0.054
2470
0.022
0.066
2150
12.5 × 20
0.018
0.045
2600
0.022
0.055
2260
12.5 × 25
0.015
0.038
3190
0.018
0.045
2660
12.5 × 30
0.013
0.033
3630
0.016
0.040
3160
12.5 × 35
0.012
0.030
3750
0.014
0.035
3270
16
× 20
0.017
0.043
3300
0.019
0.048
2870
16
× 25
0.014
0.035
3820
0.016
0.040
3320
Rated voltage
(V.DC)
Case size
(mm)
(0D×L)
5
× 11
63 V.DC
Impedance
(Ω/100 kHz)
+20 °C
–10 °C
Ripple current
(mA r.m.s./100 kHz)
+105 °C
0.510
2.040
175
6.3 × 11.2
0.210
0.840
284
8
× 11.5
0.092
0.368
566
8
× 15
0.068
0.272
741
8
× 20
0.050
0.200
930
10
× 12.5
0.063
0.252
761
10
× 16
0.045
0.180
1073
10
× 20
0.035
0.140
1229
10
× 25
0.033
0.132
1500
12.5 × 20
0.033
0.125
1582
12.5 × 25
0.027
0.092
1995
12.5 × 30
0.024
0.082
2528
12.5 × 35
0.021
0.071
2780
16
× 20
0.029
0.093
2153
16
× 25
0.024
0.074
2988
Rated voltage
(V.DC)
Case size
(mm)
(0D×L)
10
× 20
100 V.DC
Impedance
(Ω/100 kHz)
Ripple current
(mA r.m.s./100 kHz)
+20 °C
–10 °C
+105 °C
0.084
0.336
1500
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
07
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
150
220
330
470
820
1000
1200
6.3
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
100
150
220
270
470
680
820
1000
10
1500
1800
2200
3300
3900
4700
5600
6800
0D
L
5
6.3
6.3
6.3
8
8
8
10
8
10
10
10
10
12.5
12.5
12.5
12.5
16
16
5
5
6.3
6.3
8
8
10
10
8
8
10
10
10
12.5
12.5
12.5
16
12.5
12.5
16
11
11.2
11.2
11.2
11.5
11.5
15
12.5
20
16
20
25
25
20
25
30
35
20
25
11
11
11.2
11.2
11.5
11.5
12.5
16
15
20
16
20
25
20
25
30
20
35
35
25
Specification
Lead length (mm)
Ripple
Lead space
Impedance
current
Endurance Lead
(100 kHz)
(100 kHz)
(hours) dia.
Taping Taping
(+20 °C)
(+105 °C)
0d Straight ✽B
✽H
(Ω)
(mA r.m.s.)
280 0.300 5000
0.5
2.0
5.0
2.5
455 0.130
5000
0.5
2.5
5.0
2.5
455 0.130
5000
0.5
2.5
5.0
2.5
455 0.130
5000
0.5
2.5
5.0
2.5
950 0.056 6000
0.6
3.5
5.0
950 0.056 6000
0.6
3.5
5.0
1240 0.041
8000
0.6
3.5
5.0
1290 0.043 6000
0.6
5.0
5.0
1560 0.030 9000
0.6
3.5
5.0
1790 0.028 8000
0.6
5.0
5.0
2180 0.020 10000
0.6
5.0
5.0
2470 0.018 10000
0.6
5.0
5.0
2470 0.018 10000
0.6
5.0
5.0
2600 0.018 10000
0.6
5.0
5.0
3190 0.015 10000
0.6
5.0
5.0
3630 0.013 10000
0.8
5.0
3750 0.012 10000
0.8
5.0
3300 0.017 10000
0.8
7.5
7.5
3820 0.014 10000
0.8
7.5
7.5
280 0.300 5000
0.5
2.0
5.0
2.5
280 0.300 5000
0.5
2.0
5.0
2.5
455 0.130
5000
0.5
2.5
5.0
2.5
455 0.130
5000
0.5
2.5
5.0
2.5
950 0.056 6000
0.6
3.5
5.0
950 0.056 6000
0.6
3.5
5.0
1290 0.043 6000
0.6
5.0
5.0
1790 0.028 8000
0.6
5.0
5.0
1240 0.041
8000
0.6
3.5
5.0
1560 0.030 9000
0.6
3.5
5.0
1790 0.028 8000
0.6
5.0
5.0
2180 0.020 10000
0.6
5.0
5.0
2470 0.018 10000
0.6
5.0
5.0
2600 0.018 10000
0.6
5.0
5.0
3190 0.015 10000
0.6
5.0
5.0
3630 0.013 10000
0.8
5.0
3300 0.017 10000
0.8
7.5
7.5
3750 0.012 10000
0.8
5.0
3750 0.012 10000
0.8
5.0
3820 0.014 10000
0.8
7.5
7.5
Min. Packaging Q'ty
Part No.
EEUFR0J151( )
EEUFR0J221( )
EEUFR0J331( )
EEUFR0J471( )
EEUFR0J821( )
EEUFR0J102( )
EEUFR0J122L( )
EEUFR0J122( )
EEUFR0J152L( )
EEUFR0J182( )
EEUFR0J222( )
EEUFR0J272L( )
EEUFR0J332L( )
EEUFR0J392( )
EEUFR0J472( )
EEUFR0J562L
EEUFR0J682L
EEUFR0J682S( )
EEUFR0J822( )
EEUFR1A101( )
EEUFR1A151( )
EEUFR1A221( )
EEUFR1A271( )
EEUFR1A471( )
EEUFR1A681( )
EEUFR1A821( )
EEUFR1A102( )
EEUFR1A102L( )
EEUFR1A152L( )
EEUFR1A152( )
EEUFR1A182( )
EEUFR1A222L( )
EEUFR1A332( )
EEUFR1A392( )
EEUFR1A472L
EEUFR1A472S( )
EEUFR1A562L
EEUFR1A682L
EEUFR1A682( )
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
100
2000
2000
2000
2000
1000
1000
1000
500
1000
500
500
500
500
500
500
250
250
2000
2000
2000
2000
1000
1000
500
500
1000
1000
500
500
500
500
500
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
07
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
68
100
120
220
470
680
1000
16
1500
1800
2200
2700
3300
3900
4700
5600
47
68
100
150
220
330
390
470
560
25
680
820
1000
1200
1500
1800
2200
2700
3300
0D
L
5
5
6.3
6.3
8
8
10
8
10
10
10
10
12.5
12.5
12.5
16
12.5
16
12.5
16
16
5
5
6.3
6.3
8
8
8
8
8
10
8
8
10
10
10
10
10
12.5
12.5
16
12.5
16
12.5
16
16
11
11
11.2
11.2
11.5
15
12.5
20
16
20
25
25
20
25
30
20
35
20
35
25
25
11
11
11.2
11.2
11.5
11.5
15
15
20
12.5
20
20
16
20
20
25
25
20
25
20
30
20
35
20
25
Specification
Lead length (mm)
Ripple
Lead space
Impedance
current
Endurance Lead
(100 kHz)
(100 kHz)
(hours) dia.
Taping Taping
(+20 °C)
(+105 °C)
0d Straight ✽B
✽H
(Ω)
(mA r.m.s.)
280 0.300 5000
0.5
2.0
5.0
2.5
280 0.300 5000
0.5
2.0
5.0
2.5
455 0.130
5000
0.5
2.5
5.0
2.5
455 0.130
5000
0.5
2.5
5.0
2.5
950 0.056 6000
0.6
3.5
5.0
1240 0.041
8000
0.6
3.5
5.0
1290 0.043 6000
0.6
5.0
5.0
1560 0.030 9000
0.6
3.5
5.0
1790 0.028 8000
0.6
5.0
5.0
2180 0.020 10000
0.6
5.0
5.0
2470 0.018 10000
0.6
5.0
5.0
2470 0.018 10000
0.6
5.0
5.0
2600 0.018 10000
0.6
5.0
5.0
3190 0.015 10000
0.6
5.0
5.0
3630 0.013 10000
0.8
5.0
3300 0.017 10000
0.8
7.5
7.5
3750 0.012 10000
0.8
5.0
3300 0.017 10000
0.8
7.5
7.5
3750 0.012 10000
0.8
5.0
3820 0.014 10000
0.8
7.5
7.5
3820 0.014 10000
0.8
7.5
7.5
280 0.300 5000
0.5
2.0
5.0
2.5
280 0.300 5000
0.5
2.0
5.0
2.5
455 0.130 5000
0.5
2.5
5.0
2.5
455 0.130 5000
0.5
2.5
5.0
2.5
950 0.056 6000
0.6
3.5
5.0
950 0.056 6000
0.6
3.5
5.0
1240 0.041 8000
0.6
3.5
5.0
1240 0.041 8000
0.6
3.5
5.0
1560 0.030 9000
0.6
3.5
5.0
1290 0.043 6000
0.6
5.0
5.0
1560 0.030 9000
0.6
3.5
5.0
1560 0.030 9000
0.6
3.5
5.0
1790 0.028 8000
0.6
5.0
5.0
2180 0.020 10000
0.6
5.0
5.0
2180 0.020 10000
0.6
5.0
5.0
2470 0.018 10000
0.6
5.0
5.0
2470 0.018 10000
0.6
5.0
5.0
2600 0.018 10000
0.6
5.0
5.0
3190 0.015 10000
0.6
5.0
5.0
3300 0.017 10000
0.8
7.5
7.5
3630 0.013 10000
0.8
5.0
3300 0.017 10000
0.8
7.5
7.5
3750 0.012 10000
0.8
5.0
3300 0.017 10000
0.8
7.5
7.5
3820 0.014 10000
0.8
7.5
7.5
Min. Packaging Q'ty
Part No.
EEUFR1C680( )
EEUFR1C101( )
EEUFR1C121( )
EEUFR1C221( )
EEUFR1C471( )
EEUFR1C681L( )
EEUFR1C681( )
EEUFR1C102L( )
EEUFR1C102( )
EEUFR1C152( )
EEUFR1C152L( )
EEUFR1C182L( )
EEUFR1C222( )
EEUFR1C272( )
EEUFR1C332L
EEUFR1C332S( )
EEUFR1C392L
EEUFR1C392S( )
EEUFR1C472L
EEUFR1C472( )
EEUFR1C562( )
EEUFR1E470( )
EEUFR1E680( )
EEUFR1E101( )
EEUFR1E151( )
EEUFR1E221( )
EEUFR1E331( )
EEUFR1E391L( )
EEUFR1E471Y( )
EEUFR1E471L( )
EEUFR1E471( )
EEUFR1E561L( )
EEUFR1E681L( )
EEUFR1E681( )
EEUFR1E821( )
EEUFR1E102( )
EEUFR1E102L( )
EEUFR1E122L( )
EEUFR1E152( )
EEUFR1E182( )
EEUFR1E182S( )
EEUFR1E222L
EEUFR1E222S( )
EEUFR1E272L
EEUFR1E272S( )
EEUFR1E332( )
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
100
100
100
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
100
100
2000
2000
2000
2000
1000
1000
500
1000
500
500
500
500
500
500
250
250
250
250
2000
2000
2000
2000
1000
1000
1000
1000
1000
500
1000
1000
500
500
500
500
500
500
500
250
250
250
250
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
07
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
33
68
100
180
220
270
330
390
470
35
560
680
820
1000
1200
1500
1800
2200
50
4.7
10
22
47
56
100
120
150
180
220
270
330
470
560
680
820
1000
18
47
82
100
120
150
63
180
220
270
330
390
470
560
100
680
820
100
0D
L
5
6.3
8
8
8
8
10
10
8
8
10
10
10
10
10
12.5
12.5
12.5
16
12.5
16
12.5
16
5
5
5
6.3
6.3
8
8
10
8
10
10
10
12.5
12.5
12.5
12.5
16
16
5
6.3
8
8
10
8
10
8
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
16
12.5
16
10
11
11.2
11.5
11.5
11.5
15
12.5
12.5
20
20
16
20
20
25
25
20
25
30
20
35
25
35
25
11
11
11
11.2
11.2
11.5
15
12.5
20
16
20
25
20
25
30
35
20
25
11
11.2
11.5
15
12.5
20
16
20
16
20
25
20
25
20
20
25
25
30
20
35
25
20
Specification
Lead length (mm)
Ripple
Lead space
Impedance
current
Endurance Lead
(100 kHz)
(100 kHz)
(hours) dia.
Taping Taping
(+20 °C)
(+105 °C)
0d Straight ✽B
✽H
(Ω)
(mA r.m.s.)
280 0.300 5000
0.5
2.0
5.0
2.5
455 0.130 5000
0.5
2.5
5.0
2.5
950 0.056 6000
0.6
3.5
5.0
950 0.056 6000
0.6
3.5
5.0
950 0.056 6000
0.6
3.5
5.0
1240 0.041 8000
0.6
3.5
5.0
1290 0.043 6000
0.6
5.0
5.0
1330 0.043 5000
0.6
5.0
5.0
1560 0.030 9000
0.6
3.5
5.0
1560 0.030 9000
0.6
3.5
5.0
1790 0.028 8000
0.6
5.0
5.0
2180 0.020 10000
0.6
5.0
5.0
2180 0.020 10000
0.6
5.0
5.0
2470 0.018 10000
0.6
5.0
5.0
2470 0.018 10000
0.6
5.0
5.0
2600 0.018 10000
0.6
5.0
5.0
3190 0.015 10000
0.6
5.0
5.0
3630 0.013 10000
0.8
5.0
3300 0.017 10000
0.8
7.5
7.5
3750 0.012 10000
0.8
5.0
3820 0.014 10000
0.8
7.5
7.5
3750 0.012 10000
0.8
5.0
3820 0.014 10000
0.8
7.5
7.5
185 0.620 5000
0.5
2.0
5.0
2.5
250 0.340 5000
0.5
2.0
5.0
2.5
250 0.340 5000
0.5
2.0
5.0
2.5
405 0.140 5000
0.5
2.5
5.0
405 0.140 5000
0.5
2.5
5.0
2.5
870 0.061 6000
0.6
3.5
5.0
1140 0.045 8000
0.6
3.5
5.0
1170 0.042 6000
0.6
5.0
5.0
1430 0.033 9000
0.6
3.5
5.0
1650 0.030 8000
0.6
5.0
5.0
1890 0.023 10000
0.6
5.0
5.0
2150 0.022 10000
0.6
5.0
5.0
2260 0.022 10000
0.6
5.0
5.0
2660 0.018 10000
0.6
5.0
5.0
3160 0.016 10000
0.8
5.0
3270 0.014 10000
0.8
5.0
2870 0.019 10000
0.8
7.5
7.5
3320 0.016 10000
0.8
7.5
7.5
175 0.510 5000
0.5
2.0
5.0
2.5
284 0.210 5000
0.5
2.5
5.0
2.5
566 0.092 6000
0.6
3.5
5.0
741 0.068 8000
0.6
3.5
5.0
761 0.063 6000
0.6
5.0
5.0
930 0.050 9000
0.6
3.5
5.0
1073 0.045 8000
0.6
5.0
5.0
930 0.050 9000
0.6
3.5
5.0
1073 0.045 8000
0.6
5.0
5.0
1229 0.035 10000
0.6
5.0
5.0
1500 0.033 10000
0.6
5.0
5.0
1229 0.035 10000
0.6
5.0
5.0
1500 0.033 10000
0.6
5.0
5.0
1582 0.033 10000
0.6
5.0
5.0
1582 0.033 10000
0.6
5.0
5.0
1995 0.027 10000
0.6
5.0
5.0
1995 0.027 10000
0.6
5.0
5.0
2528 0.024 10000
0.8
5.0
2153 0.029 10000
0.8
7.5
7.5
2780 0.021 10000
0.8
5.0
2988 0.024 10000
0.8
7.5
7.5
1500 0.084 10000
0.6
5.0
5.0
Min. Packaging Q'ty
Part No.
EEUFR1V330( )
EEUFR1V680( )
EEUFR1V101( )
EEUFR1V181( )
EEUFR1V221( )
EEUFR1V271L( )
EEUFR1V271( )
EEUFR1V331U( )
EEUFR1V391L( )
EEUFR1V471L( )
EEUFR1V471( )
EEUFR1V561( )
EEUFR1V681( )
EEUFR1V681L( )
EEUFR1V821L( )
EEUFR1V102( )
EEUFR1V122( )
EEUFR1V152L
EEUFR1V152S( )
EEUFR1V182L
EEUFR1V182( )
EEUFR1V222L
EEUFR1V222( )
EEUFR1H4R7( )
EEUFR1H100( )
EEUFR1H220( )
EEUFR1H470( )
EEUFR1H560( )
EEUFR1H101( )
EEUFR1H121L( )
EEUFR1H151( )
EEUFR1H181L( )
EEUFR1H221( )
EEUFR1H271( )
EEUFR1H331L( )
EEUFR1H471( )
EEUFR1H561( )
EEUFR1H681L
EEUFR1H821L
EEUFR1H821S( )
EEUFR1H102( )
EEUFR1J180( )
EEUFR1J470( )
EEUFR1J820( )
EEUFR1J101L( )
EEUFR1J101( )
EEUFR1J121L( )
EEUFR1J121( )
EEUFR1J151L( )
EEUFR1J151( )
EEUFR1J181( )
EEUFR1J221L( )
EEUFR1J271U( )
EEUFR1J271L( )
EEUFR1J271( )
EEUFR1J331( )
EEUFR1J391( )
EEUFR1J471( )
EEUFR1J561L
EEUFR1J561S( )
EEUFR1J681L
EEUFR1J821( )
EEUFR2A101( )
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
100
100
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
200
2000
2000
1000
1000
1000
1000
500
500
1000
1000
500
500
500
500
500
500
500
250
250
250
2000
2000
2000
2000
2000
1000
1000
500
1000
500
500
500
500
500
250
250
2000
2000
1000
1000
500
1000
500
1000
500
500
500
500
500
500
500
500
500
250
250
500
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
07
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : EB Type : A
Features
● Endurance
: +105 °C 5000 h to 10000 h
ripple hight frequency (Hight Voltage)
● RoHS compliant
● Hight
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
–40 °C to +105 °C
10 V.DC to 63 V.DC
2.2 µF to 3300 µF
–25 °C to +105 °C
160 V.DC to 450 V.DC
10 µF to 330 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV or 3 (µA)
Leakage current
After 2 minutes application of rated working voltage at +20 °C (Whichever is greater)
Dissipation factor (tan d)
Please see the attached characteristics list
After following life test with DC voltage and +105 °C±2 °C ripple current value applied (The
sum of DC and ripple peak voltage shall not exceed the rated working voltage), when the
capacitors are restord to 20 °C, the capacitors shall meet the limits specified below.
(10 V.DC to 63 V.DC)
Duration : 05×11 to 08×11.5 : 5000 hours 08×15 to 012.5×25 : 10000 hours
Capacitance change Within ±30 % of the initial value
tan d
< 300 % of the initial limit
DC leakage current Within the initial limit
Endurance
(160 V.DC to 450 V.DC)
Duration : 5000 hours
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Shelf life
Frequency correction factor for ripple current
(10 V.DC ~ 63 V.DC)
Capacitance
(µF)
2.2 to
10
22
to 470
1000
to 3300
60
0.75
0.85
0.95
Frequency (Hz)
120
1k
10 k
1.00 1.40 1.55
1.00 1.20 1.25
1.00 1.05 1.10
Rated voltage
(V.DC)
160 to 250
350 to 450
100 k
1.65
1.30
1.15
120
0.55
0.50
Frequency (Hz)
10 k to 30k 30 k to 100k
1k
0.85
0.90
1.00
0.80
0.90
1.00
Sleeve
Pressure relief
06.3 <
fd±0.05
Dimensions
< 08
010 <
+
L✽
14 min.
0D±0.5
3 min.
F±0.5
–
0D±0.5
✽ L < 16 : L±1.0 (08×15 only L±1.5)
L > 20 : L±2.0
0D
0d
F
5
0.5
2.0
6.3
0.5
2.5
(Unit : mm)
8
0.6
3.5
10
0.6
5.0
12.5
0.6
5.0
16
0.8
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
18
0.8
7.5
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 05×11 to 08×11.5=5000 h, 08×15 to 012.5×25=10000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
100
220
10
16
25
35
50
63
470
2200
3300
1000
2200
47
100
220
330
470
1000
33
220
330
470
1000
2.2
3.3
4.7
10
22
47
100
220
330
470
2.2
3.3
4.7
10
22
33
47
100
220
330
470
0D
L
5
6.3
8
8
12.5
12.5
10
12.5
5
6.3
8
8
10
12.5
5
8
10
10
12.5
5
5
5
5
5
6.3
8
10
10
12.5
5
5
5
5
6.3
6.3
8
8
8
10
12.5
12.5
11
11.2
15
11.5
20
25
20
25
11
11.2
11.5
15
16
20
11
15
16
20
25
11
11
11
11
11
11.2
11.5
16
20
20
11
11
11
11
11.2
11.2
15
11.5
15
20
20
25
Specification
Lead length (mm)
Lead space
Ripple
Lead
current tan d
Endurance
dia.
(120 Hz) (120 Hz)
Taping Taping
(hours)
(+105 °C) (+20 °C)
0d Straight ✽B
✽H
(mA r.m.s.)
66
0.30
5000 0.5
2.0
5.0
2.5
100
0.30
5000 0.5
2.5
5.0
2.5
278
0.30 10000 0.6
3.5
5.0
180
0.30
5000 0.6
3.5
5.0
540
0.32 10000 0.6
5.0
5.0
802
0.34 10000 0.6
5.0
5.0
430
0.25 10000 0.6
5.0
5.0
706
0.27 10000 0.6
5.0
5.0
55
0.22
5000 0.5
2.0
5.0
2.5
95
0.22
5000 0.5
2.5
5.0
2.5
125
0.22
5000 0.6
3.5
5.0
255
0.22 10000 0.6
3.5
5.0
321
0.22 10000 0.6
5.0
5.0
498
0.22 10000 0.6
5.0
5.0
46
0.18
5000 0.5
2.0
5.0
2.5
197
0.18 10000 0.6
3.5
5.0
278
0.18 10000 0.6
5.0
5.0
349
0.18 10000 0.6
5.0
5.0
586
0.18 10000 0.6
5.0
5.0
15
0.15
5000 0.5
2.0
5.0
2.5
18
0.15
5000 0.5
2.0
5.0
2.5
18
0.15
5000 0.5
2.0
5.0
2.5
27
0.15
5000 0.5
2.0
5.0
2.5
39
0.15
5000 0.5
2.0
5.0
2.5
61
0.15
5000 0.5
2.5
5.0
2.5
99
0.15
5000 0.6
3.5
5.0
234
0.15 10000 0.6
5.0
5.0
293
0.15 10000 0.6
5.0
5.0
370
0.15 10000 0.6
5.0
5.0
16.5
0.12
5000 0.5
2.0
5.0
2.5
20
0.12
5000 0.5
2.0
5.0
2.5
23
0.12
5000 0.5
2.0
5.0
2.5
30
0.12
5000 0.5
2.0
5.0
2.5
40
0.12
5000 0.5
2.5
5.0
2.5
50
0.12
5000 0.5
2.5
5.0
2.5
94
0.12 10000 0.6
3.5
5.0
80
0.12
5000 0.6
3.5
5.0
180
0.12 10000 0.6
3.5
5.0
292
0.12 10000 0.6
5.0
5.0
381
0.12 10000 0.6
5.0
5.0
454
0.12 10000 0.6
5.0
5.0
Min. Packaging Q'ty
Part No.
EEUEB1A101S( )
EEUEB1A221S( )
EEUEB1A471( )
EEUEB1A471S( )
EEUEB1A222( )
EEUEB1A332( )
EEUEB1C102( )
EEUEB1C222( )
EEUEB1E470S( )
EEUEB1E101S( )
EEUEB1E221S( )
EEUEB1E331( )
EEUEB1E471( )
EEUEB1E102( )
EEUEB1V330S( )
EEUEB1V221( )
EEUEB1V331( )
EEUEB1V471( )
EEUEB1V102( )
EEUEB1H2R2S( )
EEUEB1H3R3S( )
EEUEB1H4R7S( )
EEUEB1H100S( )
EEUEB1H220S( )
EEUEB1H470S( )
EEUEB1H101S( )
EEUEB1H221( )
EEUEB1H331( )
EEUEB1H471( )
EEUEB1J2R2S( )
EEUEB1J3R3S( )
EEUEB1J4R7S( )
EEUEB1J100S( )
EEUEB1J220S( )
EEUEB1J330S( )
EEUEB1J470( )
EEUEB1J470S( )
EEUEB1J101( )
EEUEB1J221( )
EEUEB1J331( )
EEUEB1J471( )
Straight
leads Taping
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
2000
2000
1000
1000
500
500
500
500
2000
2000
1000
1000
500
500
2000
1000
500
500
500
2000
2000
2000
2000
2000
2000
1000
500
500
500
2000
2000
2000
2000
2000
2000
1000
1000
1000
500
500
500
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 5000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
22
33
47
68
160
100
150
220
330
22
33
47
68
200
100
150
220
22
33
47
250
68
100
150
10
22
33
350
47
68
100
10
22
400
33
47
10
22
450
33
47
0D
10
10
12.5
12.5
16
16
18
16
18
16
18
18
10
12.5
12.5
12.5
16
16
18
16
18
18
12.5
12.5
12.5
16
16
18
16
18
18
10
12.5
16
16
18
16
18
18
10
12.5
16
16
18
16
18
12.5
16
18
16
18
18
L
20
20
20
25
20
25
20
31.5
25
31.5
25
31.5
20
20
20
25
20
25
20
31.5
25
31.5
20
20
25
20
25
20
31.5
25
31.5
20
20
20
25
20
31.5
25
31.5
20
25
20
25
20
31.5
25
20
25
20
31.5
25
31.5
Specification
Ripple
current tan d
Endurance
(120 Hz) (120 Hz)
(hours)
(+105 °C) (+20 °C)
(mA r.m.s.)
470
0.15
5000
470
0.15
5000
600
0.15
5000
750
0.15
5000
750
0.15
5000
1060
0.15
5000
1060
0.15
5000
1280
0.15
5000
1280
0.15
5000
1280
0.15
5000
1280
0.15
5000
1690
0.15
5000
470
0.15
5000
600
0.15
5000
600
0.15
5000
750
0.15
5000
750
0.15
5000
1060
0.15
5000
1060
0.15
5000
1280
0.15
5000
1280
0.15
5000
1690
0.15
5000
560
0.15
5000
560
0.15
5000
710
0.15
5000
710
0.15
5000
990
0.15
5000
990
0.15
5000
1200
0.15
5000
1200
0.15
5000
1470
0.15
5000
270
0.20
5000
350
0.20
5000
480
0.20
5000
640
0.20
5000
640
0.20
5000
780
0.20
5000
780
0.20
5000
970
0.20
5000
250
0.24
5000
410
0.24
5000
410
0.24
5000
600
0.24
5000
600
0.24
5000
730
0.24
5000
730
0.24
5000
310
0.24
5000
560
0.24
5000
560
0.24
5000
680
0.24
5000
680
0.24
5000
850
0.24
5000
Lead length (mm)
Lead space
Lead
dia.
Taping
Straight
0d
✽B
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.6
0.8
0.8
0.8
0.8
0.8
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
7.5
7.5
7.5
7.5
7.5
5.0
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
7.5
7.5
7.5
–
7.5
–
7.5
–
5.0
5.0
5.0
5.0
7.5
7.5
7.5
–
7.5
–
5.0
5.0
5.0
7.5
7.5
7.5
–
7.5
–
5.0
5.0
7.5
7.5
7.5
–
7.5
–
5.0
5.0
7.5
7.5
7.5
–
7.5
5.0
7.5
7.5
–
7.5
–
Min. Packaging Q'ty
Part No.
EEUEB2C220( )
EEUEB2C330( )
EEUEB2C470( )
EEUEB2C680( )
EEUEB2C680S( )
EEUEB2C101( )
EEUEB2C101S( )
EEUEB2C151
EEUEB2C151S( )
EEUEB2C221
EEUEB2C221S( )
EEUEB2C331
EEUEB2D220( )
EEUEB2D330( )
EEUEB2D470( )
EEUEB2D680( )
EEUEB2D680S( )
EEUEB2D101( )
EEUEB2D101S( )
EEUEB2D151
EEUEB2D151S( )
EEUEB2D221
EEUEB2E220( )
EEUEB2E330( )
EEUEB2E470( )
EEUEB2E470S( )
EEUEB2E680( )
EEUEB2E680S( )
EEUEB2E101
EEUEB2E101S( )
EEUEB2E151
EEUEB2V100( )
EEUEB2V220( )
EEUEB2V330S( )
EEUEB2V470( )
EEUEB2V470S( )
EEUEB2V680
EEUEB2V680S( )
EEUEB2V101
EEUEB2G100( )
EEUEB2G220( )
EEUEB2G220S( )
EEUEB2G330( )
EEUEB2G330S( )
EEUEB2G470
EEUEB2G470S( )
EEUEB2W100( )
EEUEB2W220( )
EEUEB2W220S( )
EEUEB2W330( )
EEUEB2W330S( )
EEUEB2W470
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
100
100
100
100
100
100
100
50
200
200
200
200
100
100
100
100
100
50
200
200
200
100
100
100
100
100
50
200
200
100
100
100
100
100
50
200
200
100
100
100
100
100
200
100
100
100
100
50
500
500
500
500
250
250
250
–
250
–
250
–
500
500
500
500
250
250
250
–
250
–
500
500
500
250
250
250
–
250
–
500
500
250
250
250
–
250
–
500
500
250
250
250
–
250
500
250
250
–
250
–
· When requesting taped product, please put the letter "B" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : EE Type : A
Features
● High
ripple current (at high frequency) : 40 % higher than ED Series
: 105 °C 8000 h to 10000 h
● RoHS compliant
● Endurance
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
Leakage current
Dissipation factor
(tan d)
Endurance
Shelf life
–25 °C to + 105 °C
160 V .DC to 450 V .DC
10 µF to 330 µF
±20 % (120 Hz/+20 °C)
I < 0.06 CV +10 (µA) After 2 minutes
V.DC
160 200 250 350 400 450
(120 Hz/+20 °C)
tan d
0.15 0.15 0.15 0.20 0.24 0.24
After following life test with DC voltage and +105 °C±2 °C ripple current value applied
(The sum of DC and ripple peak voltage shall not exceed the rated working voltage),
when the capacitors are restored to 20 °C, the capacitors shall meet the limits specified below.
Duration
010 : 8000 hours
012.5 to 018 : 10000 hours
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Frequency correction factor for ripple current
Rated voltage
(V.DC)
160 to 450
Frequency (Hz)
Capacitance
(µF)
60 <
120 <
300 <
1k<
10 k <
100 k <
10 to 82
0.25
0.35
0.50
0.65
0.90
1.00
100 to 330
0.30
0.40
0.55
0.70
0.90
1.00
Sleeve
Pressure relief
fd±0.05
Dimensions
+
L±2.0
14 min.
3 min.
0D±0.5
F±0.5
–
(Unit : mm)
0D
10
12.5
16
18
0d
0.6
0.6
0.8
0.8
F
5.0
5.0
7.5
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Case size/Ripple current
160 V.DC
Capacitance
(µF)
Case size (mm)
(0D×L)
100 kHz
700
810
1065
470
1350
25
25
20S
25
20S
520
660
680
755
730
1480
1660
1700
1890
1820
16
18
× 31.5
× 25S
910
780
18
× 31.5
1040
10
10
10
68
12.5 × 20
82
12.5
12.5
16
16
18
×
×
×
×
×
220
330
150
Ripple current
(mA r.m.s.) 105 °C
120 Hz
245
280
370
× 20
× 20
× 20
22
33
47
100
200 V.DC
Case size (mm)
(0D×L)
120 Hz
300
320
385
100 kHz
850
920
1100
12.5 × 25
16
× 20S
465
465
1330
1330
16
16
18
× 20S
× 25
× 20S
510
690
670
1460
1730
1665
16
× 25
740
1860
2280
1950
18
× 31.5
1175
2600
2600
18
× 40
1250
3120
10
× 20
10
× 20
12.5 × 20
250 V.DC
Capacitance
(µF)
Case size (mm)
(0D×L)
350 V.DC
Ripple current
(mA r.m.s.) 105 °C
120 Hz
100 kHz
Case size (mm)
(0D×L)
Ripple current
(mA r.m.s.) 105 °C
120 Hz
170
230
100 kHz
480
660
12.5 × 25
16
× 20S
275
315
790
900
16
18
× 25
× 20S
375
375
1070
1070
1400
16
18
× 31.5
× 25S
535
465
1530
1330
590
590
1680
1680
18
× 25S
535
1530
× 31.5
× 25S
840
840
2100
2100
18
× 31.5
640
1600
× 31.5
× 40
1010
1175
2520
2940
15
22
10
× 20
275
785
33
12.5 × 20
350
995
47
12.5 × 25
16
× 20S
450
490
1290
1400
68
16
× 20S
490
82
16
18
× 25
× 20S
100
16
18
150
220
18
18
10
× 20
12.5 × 20
400 V.DC
Capacitance
(µF)
Ripple current
(mA r.m.s.) 105 °C
Case size (mm)
(0D×L)
450 V.DC
Ripple current
(mA r.m.s.) 105 °C
120 Hz
100 kHz
Case size (mm)
(0D×L)
Ripple current
(mA r.m.s.) 105 °C
120 Hz
100 kHz
10
10
× 20
150
430
10
× 20U
12.5 × 20
115
170
330
490
15
12.5 × 20
205
590
12.5 × 25
270
780
22
12.5 × 25
16
× 20S
265
300
760
860
16
× 20S
330
945
33
16
× 20S
355
1020
16
18
× 25
× 20S
350
350
1000
1000
47
16
18
× 25
× 20S
410
410
1180
1180
16
18
× 31.5
× 25S
420
420
1200
1200
18
18
18
× 25
× 31.5
× 40
515
575
825
1470
1645
2060
18
18
× 31.5
× 40
480
630
1380
1800
56
68
82
100
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 010=8000 h, 012.5 to 018=10000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
22
33
47
68
82
160
100
150
220
330
22
33
47
68
200
82
100
150
220
330
22
33
47
68
250
82
100
150
220
15
22
33
350
47
68
82
100
0D
L
10
10
10
12.5
12.5
12.5
16
16
18
16
18
18
10
10
12.5
12.5
16
16
16
18
16
18
18
10
12.5
12.5
16
16
16
18
16
18
18
18
10
12.5
12.5
16
16
18
16
18
18
18
20
20
20
20
25
25
20
25
20
31.5
25
31.5
20
20
20
25
20
20
25
20
25
31.5
40
20
20
25
20
20
25
20
31.5
25
31.5
40
20
20
25
20
25
20
31.5
25
25
31.5
Specification
Lead length (mm)
Ripple
Lead space
Lead
current tan d
Endurance
dia.
(100 kHz) (120 Hz)
Taping
(hours)
Straight
(+105 °C) (+20 °C)
0d
✽B
(mA r.m.s.)
700
0.15
8000
0.6
5.0
5.0
810
0.15
8000
0.6
5.0
5.0
1065
0.15
8000
0.6
5.0
5.0
1350
0.15 10000
0.6
5.0
5.0
1480
0.15 10000
0.6
5.0
5.0
1660
0.15 10000
0.6
5.0
5.0
1700
0.15 10000
0.8
7.5
7.5
1890
0.15 10000
0.8
7.5
7.5
1820
0.15 10000
0.8
7.5
7.5
2280
0.15 10000
0.8
7.5
1950
0.15 10000
0.8
7.5
7.5
2600
0.15 10000
0.8
7.5
850
0.15
8000
0.6
5.0
5.0
920
0.15
8000
0.6
5.0
5.0
1100
0.15 10000
0.6
5.0
5.0
1330
0.15 10000
0.6
5.0
5.0
1330
0.15 10000
0.8
7.5
7.5
1460
0.15 10000
0.8
7.5
7.5
1730
0.15 10000
0.8
7.5
7.5
1665
0.15 10000
0.8
7.5
7.5
1860
0.15 10000
0.8
7.5
7.5
2600
0.15 10000
0.8
7.5
3120
0.15 10000
0.8
7.5
785
0.15
8000
0.6
5.0
5.0
995
0.15 10000
0.6
5.0
5.0
1290
0.15 10000
0.6
5.0
5.0
1400
0.15 10000
0.8
7.5
7.5
1400
0.15 10000
0.8
7.5
7.5
1680
0.15 10000
0.8
7.5
7.5
1680
0.15 10000
0.8
7.5
7.5
2100
0.15 10000
0.8
7.5
2100
0.15 10000
0.8
7.5
7.5
2520
0.15 10000
0.8
7.5
2940
0.15 10000
0.8
7.5
480
0.20
8000
0.6
5.0
5.0
660
0.20 10000
0.6
5.0
5.0
790
0.20 10000
0.6
5.0
5.0
900
0.20 10000
0.8
7.5
7.5
1070
0.20 10000
0.8
7.5
7.5
1070
0.20 10000
0.8
7.5
7.5
1530
0.20 10000
0.8
7.5
1330
0.20 10000
0.8
7.5
7.5
1530
0.20 10000
0.8
7.5
7.5
1600
0.20 10000
0.8
7.5
Min. Packaging Q'ty
Part No.
EEUEE2C220( )
EEUEE2C330( )
EEUEE2C470( )
EEUEE2C680( )
EEUEE2C820( )
EEUEE2C101( )
EEUEE2C101S( )
EEUEE2C151( )
EEUEE2C151S( )
EEUEE2C221
EEUEE2C221S( )
EEUEE2C331
EEUEE2D220( )
EEUEE2D330( )
EEUEE2D470( )
EEUEE2D680( )
EEUEE2D680S( )
EEUEE2D820S( )
EEUEE2D101( )
EEUEE2D101S( )
EEUEE2D151( )
EEUEE2D221
EEUEE2D331
EEUEE2E220( )
EEUEE2E330( )
EEUEE2E470( )
EEUEE2E470S( )
EEUEE2E680S( )
EEUEE2E820( )
EEUEE2E820S( )
EEUEE2E101
EEUEE2E101S( )
EEUEE2E151
EEUEE2E221
EEUEE2V150( )
EEUEE2V220( )
EEUEE2V330( )
EEUEE2V330S( )
EEUEE2V470( )
EEUEE2V470S( )
EEUEE2V680
EEUEE2V680S( )
EEUEE2V820S( )
EEUEE2V101
Straight
leads Taping
(pcs)
(pcs)
200
200
200
200
200
200
100
100
100
100
100
50
200
200
200
200
100
100
100
100
100
50
50
200
200
200
100
100
100
100
100
100
50
50
200
200
200
100
100
100
100
100
100
50
500
500
500
500
500
500
250
250
250
250
500
500
500
500
250
250
250
250
250
500
500
500
250
250
250
250
250
500
500
500
250
250
250
250
250
· When requesting taped product, please put the letter "B" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 010=8000 h, 012.5 to 018=10000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
10
15
22
400
33
47
68
82
100
10
15
22
450
33
47
56
68
0D
L
10
12.5
12.5
16
16
16
18
18
18
18
10
12.5
12.5
16
16
18
16
18
18
18
20
20
25
20
20
25
20
25
31.5
40
20
20
25
20
25
20
31.5
25
31.5
40
Specification
Lead length (mm)
Ripple
Lead space
Lead
current tan d
Endurance
dia.
(100 kHz) (120 Hz)
Taping
(hours)
Straight
(+105 °C) (+20 °C)
0d
✽B
(mA r.m.s.)
430
0.24
8000
0.6
5.0
5.0
590
0.24 10000
0.6
5.0
5.0
760
0.24 10000
0.6
5.0
5.0
860
0.24 10000
0.8
7.5
7.5
1020
0.24 10000
0.8
7.5
7.5
1180
0.24 10000
0.8
7.5
7.5
1180
0.24 10000
0.8
7.5
7.5
1470
0.24 10000
0.8
7.5
7.5
1645
0.24 10000
0.8
7.5
2060
0.24 10000
0.8
7.5
330
0.24
8000
0.6
5.0
5.0
490
0.24 10000
0.6
5.0
5.0
780
0.24 10000
0.6
5.0
5.0
945
0.24 10000
0.8
7.5
7.5
1000
0.24 10000
0.8
7.5
7.5
1000
0.24 10000
0.8
7.5
7.5
1200
0.24 10000
0.8
7.5
1200
0.24 10000
0.8
7.5
7.5
1380
0.24 10000
0.8
7.5
1800
0.24 10000
0.8
7.5
Min. Packaging Q'ty
Part No.
EEUEE2G100( )
EEUEE2G150( )
EEUEE2G220( )
EEUEE2G220S( )
EEUEE2G330S( )
EEUEE2G470( )
EEUEE2G470S( )
EEUEE2G680( )
EEUEE2G820
EEUEE2G101
EEUEE2W100U( )
EEUEE2W100( )
EEUEE2W150( )
EEUEE2W220S( )
EEUEE2W330( )
EEUEE2W330S( )
EEUEE2W470
EEUEE2W470S( )
EEUEE2W560
EEUEE2W680
Straight
leads Taping
(pcs)
(pcs)
200
200
200
100
100
100
100
100
50
50
200
200
200
100
100
100
100
100
50
50
500
500
500
250
250
250
250
250
500
500
500
250
250
250
250
· When requesting taped product, please put the letter "B" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : TA Type : A
Features
● Endurance:
125 °C 2000 h
cycle: 1000 cycle –40 °C to +125 °C
● RoHS compliant
● Heat
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
Leakage current
–40 °C to + 125 °C
10 V .DC to 63 V .DC
2.2 µF to 4700 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV or 3 (µA) After 2 minutes (Whichever is greater)
V.DC
10
16
25
35
50
63
(120Hz / +20 °C)
tan d
0.20 0.16 0.14 0.12 0.10 0.09
For capacitance value > 1000 µF , add 0.02 per every 1000 µF.
After following life test with DC voltage and +125 °C±2 °C ripple current value applied (The sum
of DC and ripple peak voltage shall not exceed the rated working voltage), for 2000 hours,
when the capacitors are restored to 20 °C, the capacitors, shall meet the limits specified below.
Capacitance change Within ±30 % of the initial value
tan d
< 300 % of the initial limit
DC leakage current Within the initial limit
Dissipation factor
(tan d)
Endurance
Shelf life
After storage for 1000 hours at +125 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
AEC-Q200
AEC-Q200 compliant
Frequency correction factor for ripple current
Rated voltage
(V.DC)
Frequency (Hz)
Capacitance
(µF)
10 to 63
60
120
1k
10 k
100 k
1
to
330
0.55
0.65
0.85
0.90
1.00
470
to
1000
0.70
0.75
0.90
0.95
1.00
2200
to
4700
0.75
0.80
0.90
0.95
1.00
Sleeve
fd±0.05
Dimensions
08
010 <
+
Pressure relief
L✽
14 min.
3 min.
0D±0.5
F±0.5
–
0D±0.5
✽ L < 16 : L±1.0 (016×15, 018×15 : L±1.5)
L > 20 : L±2.0
(Unit : mm)
0D
8
10
12.5
16
18
0d
0.6
0.6
0.6
0.8
0.8
F
3.5
5.0
5.0
7.5
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 125 °C 2000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
330
470
1000
10
2200
3300
4700
220
330
470
1000
16
2200
3300
4700
100
220
330
470
25
1000
2200
3300
100
220
330
35
470
1000
2200
0D
L
8
10
10
12.5
12.5
16
18
16
18
16
18
8
10
10
12.5
16
16
18
16
18
18
8
10
10
10
12.5
12.5
16
18
16
18
18
10
10
10
12.5
16
16
18
18
11.5
12.5
20
15
25
20
15
25
20
31.5
25
11.5
12.5
16
20
15
25
20
31.5
25
31.5
11.5
12.5
16
20
15
25
20
15
31.5
25
35.5
12.5
16
20
20
15
25
20
35.5
Specification
Ripple
Impedance
current
(100 kHz)
(100 kHz)
(+20 °C)
(+125 °C)
(Ω)
(mA r.m.s.)
500
0.130
680
0.100
1100
0.057
1085
0.070
1750
0.033
1985
0.032
1800
0.042
2300
0.024
2250
0.031
2710
0.020
2470
0.022
500
0.130
680
0.100
945
0.075
1490
0.042
1520
0.047
2300
0.024
2250
0.031
2710
0.020
2470
0.022
3270
0.018
500
0.130
680
0.100
945
0.075
1100
0.057
1085
0.070
1750
0.033
1985
0.032
1800
0.042
2710
0.020
2470
0.022
3310
0.017
555
0.180
765
0.130
930
0.100
1330
0.070
1450
0.088
2010
0.037
2180
0.046
2790
0.025
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
0d
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
Part No.
Taping
Straight
✽B
3.5
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
3.5
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
3.5
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
5.0
5.0
5.0
5.0
7.5
7.5
7.5
EEUTA1A331( )
EEUTA1A471( )
EEUTA1A102( )
EEUTA1A102S( )
EEUTA1A222L( )
EEUTA1A222( )
EEUTA1A222S( )
EEUTA1A332( )
EEUTA1A332S( )
EEUTA1A472
EEUTA1A472S( )
EEUTA1C221( )
EEUTA1C331( )
EEUTA1C471( )
EEUTA1C102( )
EEUTA1C102S( )
EEUTA1C222( )
EEUTA1C222S( )
EEUTA1C332
EEUTA1C332S( )
EEUTA1C472
EEUTA1E101( )
EEUTA1E221( )
EEUTA1E331( )
EEUTA1E471( )
EEUTA1E471S( )
EEUTA1E102L( )
EEUTA1E102( )
EEUTA1E102S( )
EEUTA1E222
EEUTA1E222S( )
EEUTA1E332
EEUTA1V101( )
EEUTA1V221( )
EEUTA1V331( )
EEUTA1V471( )
EEUTA1V471S( )
EEUTA1V102( )
EEUTA1V102S( )
EEUTA1V222
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
100
100
100
100
100
100
200
200
200
200
100
100
100
100
100
50
200
200
200
200
200
200
100
100
100
100
50
200
200
200
200
100
100
100
50
1000
500
500
500
500
250
250
250
250
250
1000
500
500
500
250
250
250
250
1000
500
500
500
500
500
250
250
250
500
500
500
500
250
250
250
· When requesting taped product, please put the letter "B" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 125 °C 2000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
10
22
33
47
100
220
50
330
470
1000
22
33
47
100
63
220
330
470
0D
L
8
8
8
8
10
10
12.5
16
12.5
16
18
16
18
8
10
10
10
12.5
16
18
16
18
16
18
11.5
11.5
11.5
11.5
12.5
20
20
15
25
20
15
31.5
25
11.5
12.5
16
20
25
20
15
25
20
31.5
25
Specification
Ripple
Impedance
current
(100 kHz)
(100 kHz)
(+20 °C)
(+125 °C)
(Ω)
(mA r.m.s.)
180
0.950
250
0.650
300
0.450
440
0.350
555
0.180
930
0.100
1330
0.070
1450
0.088
1650
0.055
1650
0.053
1710
0.075
2430
0.031
2350
0.032
310
0.470
410
0.360
460
0.270
680
0.205
1325
0.100
1360
0.085
1300
0.120
1660
0.070
1760
0.077
2055
0.060
1990
0.060
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
0d
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.6
0.8
0.8
0.8
0.8
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
Part No.
Taping
Straight
✽B
3.5
3.5
3.5
3.5
5.0
5.0
5.0
7.5
5.0
7.5
7.5
7.5
7.5
3.5
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
EEUTA1H100( )
EEUTA1H220( )
EEUTA1H330( )
EEUTA1H470S( )
EEUTA1H101( )
EEUTA1H221( )
EEUTA1H331( )
EEUTA1H331S( )
EEUTA1H471L( )
EEUTA1H471( )
EEUTA1H471S( )
EEUTA1H102
EEUTA1H102S( )
EEUTA1J220( )
EEUTA1J330( )
EEUTA1J470( )
EEUTA1J101( )
EEUTA1J221L( )
EEUTA1J221( )
EEUTA1J221S( )
EEUTA1J331( )
EEUTA1J331S( )
EEUTA1J471
EEUTA1J471S( )
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
100
200
100
100
100
100
200
200
200
200
200
100
100
100
100
100
100
1000
1000
1000
1000
500
500
500
250
500
250
250
250
1000
500
500
500
500
250
250
250
250
250
· When requesting taped product, please put the letter "B" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : TP Type : A
Features
● Endurance : 125 °C 2000 h to 5000 h or 135 °C 1000 h to 2000 h
● Smaller than series TA
● High ripple current (at high frequency) : 20 to 40% higher than TA series
● RoHS compliant
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
Leakage current
Dissipation factor
(tan d)
Endurance 1
Endurance 2
Shelf Life 1
Shelf Life 2
AEC-Q200
–40 °C to + 135 °C
25 V .DC to 35 V .DC
100 µF to 5100 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV After 2 minutes
V.DC
tan d
25
35
(120Hz / +20 °C)
0.14 0.12
For capacitance value > 1000 µF , add 0.02 per every 1000 µF.
After following life test with DC voltage and +125 °C±2 °C ripple current value applied. (The
sum of DC and ripple peak voltage shall not exceed the rated working voltage) when the
capacitors are restored to 20 °C, the capacitors shall meet the limits specified below.
Duration
08 : 2000 hours, 010 : 3000 hours, 012.5 : 4000 hours, 016 to 018 : 5000 hours
Capacitance change Within ±30 % of the initial value
tan d
< 300 % of the initial limit
DC leakage current Within the initial limit
After following life test with DC voltage and +135 °C±2 °C ripple current value applied. (The
sum of DC and ripple peak voltage shall not exceed the rated working voltage) when the
capacitors are restored to 20 °C, the capacitors shall meet the limits specified below.
Duration
08 : 1000 hours, 010 to 018 : 2000 hours
Capacitance change Within ±30 % of the initial value
tan d
< 300 % of the initial limit
DC leakage current Within the initial limit
After storage for 1000 hours at +125 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
After storage for 1000 hours at +135 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
AEC-Q200 compliant
Frequency correction factor for ripple current
Rated voltage
(V.DC)
25 to 35
Capacitance
(µF)
to
330
390
to
1000
1200
to
60
0.55
0.70
0.75
120
0.65
0.75
0.80
Frequency (Hz)
1k
0.85
0.90
0.90
10 k
0.90
0.95
0.95
100 k
1.00
1.00
1.00
fd±0.05
Dimensions
Sleeve
08
010 <
+
Pressure relief
L✽
✽ L < 16 : L±1.5
L > 20 : L±2.0
0D
0d
F
8
0.6
3.5
14 min.
3 min.
0D±0.5
F±0.5
–
0D±0.5
(Unit : mm)
10
0.6
5.0
12.5
0.6
5.0
16
0.8
7.5
18
0.8
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF) 0D
25
35
220 10
330 10
8
470
10
510 10
820 10
1000 12.5
1200 12.5
12.5
1800
16
2000 16
16
2200
18
16
2700
18
16
3300
18
16
3900
18
4700 18
5100 18
100 10
120 10
8
220
10
8
270
10
330 10
390 10
470 12.5
560 12.5
620 12.5
820 12.5
1000 16
1200 16
16
1500
18
1600 16
16
1800
18
16
2000
18
2200 18
2700 18
L
12.5
16
20
16
16
20
20
20
25
20
20
25
20
25
20
31.5
25
31.5
25
31.5
31.5
12.5
12.5
20
16
20
16
20
20
20
20
20
25
20
20
25
20
25
31.5
25
31.5
25
31.5
31.5
Specification
Ripple Ripple
current current
(100 kHz) (100 kHz)
(+125 °C) (+135 °C)
(mA r.m.s.) (mA r.m.s.)
580
500
1100
945
1060
760
1100
945
1100
945
1540 1100
1860 1490
1860 1490
2180 1750
2380 1985
2380 1985
2760 2300
2700 2250
2760 2300
2700 2250
3250 2710
2960 2470
3250 2710
2960 2470
3480 2900
3480 2900
580
500
580
500
1060
760
1100
945
1060
760
1100
945
1540 1100
1540 1100
1860 1490
1860 1490
1860 1490
2180 1750
2380 1985
2380 1985
2760 2300
2700 2250
2760 2300
3250 2710
2960 2470
3250 2710
2960 2470
3480 2900
3480 2900
Lead length (mm)
Min. Packaging Q'ty
Lead space
ESR
Straight
tan d 125 °C 135 °C Lead
Part No.
(100 kHz)
Taping
Taping
leads
(120 Hz) Enduance Enduance dia.
(pcs)
(+20 °C)
Straight
(+20 °C) (hours) (hours) 0d
(pcs)
✽B ✽ : Substandard
(Ω)
(E24series numbers)
0.190
0.130
0.067
0.130
0.130
0.052
0.038
0.038
0.030
0.029
0.029
0.022
0.028
0.022
0.028
0.018
0.020
0.018
0.020
0.016
0.016
0.190
0.190
0.067
0.130
0.067
0.130
0.052
0.052
0.038
0.038
0.038
0.030
0.029
0.029
0.022
0.028
0.022
0.018
0.020
0.018
0.020
0.016
0.016
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.16
0.16
0.16
0.16
0.16
0.18
0.18
0.18
0.18
0.20
0.22
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.14
0.14
0.14
0.14
3000
3000
2000
3000
3000
3000
4000
4000
4000
5000
5000
5000
5000
5000
5000
5000
5000
5000
5000
5000
5000
3000
3000
2000
3000
2000
3000
3000
3000
4000
4000
4000
4000
5000
5000
5000
5000
5000
5000
5000
5000
5000
5000
5000
2000
2000
1000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
1000
2000
1000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
5.0
5.0
3.5
5.0
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
3.5
5.0
3.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
EEUTP1E221( )
EEUTP1E331( )
EEUTP1E471L( )
EEUTP1E471( )
EEUTP1E511( )✽
EEUTP1E821( )
EEUTP1E102( )
EEUTP1E122( )
EEUTP1E182( )
EEUTP1E182S( )
EEUTP1E202S( )✽
EEUTP1E222( )
EEUTP1E222S( )
EEUTP1E272( )
EEUTP1E272S( )
EEUTP1E332
EEUTP1E332S( )
EEUTP1E392
EEUTP1E392S( )
EEUTP1E472
EEUTP1E512✽
EEUTP1V101( )
EEUTP1V121( )
EEUTP1V221L( )
EEUTP1V221( )
EEUTP1V271L( )
EEUTP1V271( )
EEUTP1V331( )
EEUTP1V391( )
EEUTP1V471( )
EEUTP1V561( )
EEUTP1V621( )✽
EEUTP1V821( )
EEUTP1V102( )
EEUTP1V122( )
EEUTP1V152( )
EEUTP1V152S( )
EEUTP1V162( )✽
EEUTP1V182
EEUTP1V182S( )
EEUTP1V202✽
EEUTP1V202S( )✽
EEUTP1V222
EEUTP1V272
200
200
200
200
200
200
200
200
200
100
100
100
100
100
100
100
100
100
100
50
50
200
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
100
100
100
100
100
50
50
500
500
1000
500
500
500
500
500
500
250
250
250
250
250
250
250
250
500
500
1000
500
1000
500
500
500
500
500
500
500
250
250
250
250
250
250
250
· When requesting taped product, please put the letter "B" between the "( )". Lead wire pitch ✽B=5 mm, 7.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : HD Type : A
Features
● Endurance
: 105 °C 1000 h to 2000 h
Higher Capacitance : 1 Size Miniturized Product of Current A-NHG
● RoHS compliant
● Minaturize,
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
–55 °C to +105 °C
10 V.DC to 50 V.DC
2.2 µF to 22000 µF
±20 % (120 Hz/+20 °C)
Leakage current
I < 0.01 CV or 3 (µA) After 2 minutes
(Which is greater)
Dissipation factor (tan d)
Please see the attached characteristics list
After following life test with DC voltage and +105 °C±2 °C ripple current value applied (The sum
of DC and ripple peak voltage shall not exceed the rated working voltage), When the capacitors
are restored to 20 °C, the capacitors shall meet the limits specified below.
Endurance
Duration : 05 to 08=1000 hours, 010 to 018=2000 hours
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Shelf life
Frequency correction factor for ripple current
Rated voltage
(V.DC)
2.2
10 to 50
Frequency (Hz)
Capacitance
(µF)
60
120
1k
10 k
100 k
to
33
0.75
1.00
1.55
1.80
2.00
47
to
470
0.80
1.00
1.35
1.50
1.50
1000
to
22000
0.85
1.00
1.10
1.15
1.15
fd±0.05
Dimensions
Sleeve
Pressure relief
06.3 <
< 08
010 <
+
L✽
14 min.
0D±0.5
3 min.
F±0.5
–
0D±0.5
✽ L < 16 : L±1.5
L > 20 : L±2.0
(Unit : mm)
0D
0d
F
5
0.5
2.0
6.3
0.5
2.5
8
0.6
3.5
10
0.6
5.0
12.5
0.6
5.0
16
0.8
7.5
18
0.8
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 05 to 08=1000 h, 010 to 018=2000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
0D
L
330
470
1000
2200
4700
6800
10000
15000
22000
100
220
330
470
3300
4700
6800
8200
10000
15000
47
68
100
220
330
470
1000
2200
3300
4700
5600
6800
10000
47
100
220
330
470
680
2200
3300
4700
6800
6.3
8
10
10
12.5
12.5
16
16
18
5
6.3
8
8
12.5
12.5
16
16
16
18
5
5
6.3
8
8
10
10
12.5
12.5
16
16
16
18
5
6.3
8
10
10
10
12.5
16
16
18
11.2
11.5
12.5
16
20
25
25
31.5
35.5
11
11.2
11.5
11.5
20
25
25
25
31.5
35.5
11
11
11.2
11.5
11.5
12.5
16
20
25
25
25
31.5
35.5
11
11.2
11.5
12.5
16
16
25
25
31.5
35.5
10
16
25
35
Specification
Lead length (mm)
Ripple
Lead space
Lead
current tan d
Endurance
dia.
(120 Hz) (120 Hz)
Taping Taping
(hours)
(+105 °C) (+20 °C)
0d Straight ✽B
✽H
(mA r.m.s.)
200
0.24 1000
0.5
2.5
5.0
2.5
250
0.24 1000
0.6
3.5
5.0
460
0.24 2000
0.6
5.0
5.0
760
0.26 2000
0.6
5.0
5.0
1260
0.30 2000
0.6
5.0
5.0
1570
0.34 2000
0.6
5.0
5.0
1890
0.42 2000
0.8
7.5
7.5
2180
0.52 2000
0.8
7.5
2400
0.66 2000
0.8
7.5
110
0.20 1000
0.5
2.0
5.0
2.5
180
0.20 1000
0.5
2.5
5.0
2.5
260
0.20 1000
0.6
3.5
5.0
310
0.20 1000
0.6
3.5
5.0
1170
0.24 2000
0.6
5.0
5.0
1480
0.26 2000
0.6
5.0
5.0
1780
0.30 2000
0.8
7.5
7.5
1780
0.34 2000
0.8
7.5
7.5
2060
0.38 2000
0.8
7.5
2210
0.48 2000
0.8
7.5
91
0.16 1000
0.5
2.0
5.0
2.5
91
0.16 1000
0.5
2.0
5.0
2.5
130
0.16 1000
0.5
2.5
5.0
2.5
230
0.16 1000
0.6
3.5
5.0
310
0.16 1000
0.6
3.5
5.0
380
0.16 2000
0.6
5.0
5.0
680
0.16 2000
0.6
5.0
5.0
1090
0.18 2000
0.6
5.0
5.0
1400
0.20 2000
0.6
5.0
5.0
1750
0.22 2000
0.8
7.5
7.5
1750
0.24 2000
0.8
7.5
7.5
2040
0.26 2000
0.8
7.5
2200
0.34 2000
0.8
7.5
90
0.14 1000
0.5
2.0
5.0
2.5
150
0.14 1000
0.5
2.5
5.0
2.5
270
0.14 1000
0.6
3.5
5.0
350
0.14 2000
0.6
5.0
5.0
460
0.14 2000
0.6
5.0
5.0
460
0.14 2000
0.6
5.0
5.0
1260
0.16 2000
0.6
5.0
5.0
1610
0.18 2000
0.8
7.5
7.5
1910
0.20 2000
0.8
7.5
2050
0.24 2000
0.8
7.5
Min. Packaging Q'ty
Part No.
EEUHD1A331( )
EEUHD1A471( )
EEUHD1A102( )
EEUHD1A222( )
EEUHD1A472( )
EEUHD1A682( )
EEUHD1A103( )
EEUHD1A153
EEUHD1A223
EEUHD1C101( )
EEUHD1C221( )
EEUHD1C331( )
EEUHD1C471( )
EEUHD1C332( )
EEUHD1C472( )
EEUHD1C682( )
EEUHD1C822( )
EEUHD1C103
EEUHD1C153
EEUHD1E470( )
EEUHD1E680( )
EEUHD1E101( )
EEUHD1E221( )
EEUHD1E331( )
EEUHD1E471( )
EEUHD1E102( )
EEUHD1E222( )
EEUHD1E332( )
EEUHD1E472( )
EEUHD1E562( )
EEUHD1E682
EEUHD1E103
EEUHD1V470( )
EEUHD1V101( )
EEUHD1V221( )
EEUHD1V331( )
EEUHD1V471( )
EEUHD1V681( )
EEUHD1V222( )
EEUHD1V332( )
EEUHD1V472
EEUHD1V682
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
100
100
50
200
200
200
200
200
200
100
100
100
50
200
200
200
200
200
200
200
200
200
100
100
100
50
200
200
200
200
200
200
200
100
100
50
2000
1000
500
500
500
500
250
2000
2000
1000
1000
500
500
250
250
2000
2000
2000
1000
1000
500
500
500
500
250
250
2000
2000
1000
500
500
500
500
250
· When requesting taped product, please put the letter “B” or “H” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 05 to 08=1000 h, 010 to 018=2000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
50
0D
L
Specification
Lead length (mm)
Ripple
Lead space
current tan d
Lead
Part No.
Endurance
(120 Hz) (120 Hz)
dia.
Taping Taping
(hours)
Straight
(+105 °C) (+20 °C)
0d
✽B
✽H
(mA r.m.s.)
18
0.12 1000
0.5
2.0
5.0
2.5
EEUHD1H2R2( )
Min. Packaging Q'ty
Straight
Taping
leads
(pcs)
(pcs)
2.2
5
11
200
2000
3.3
5
11
22
0.12
1000
0.5
2.0
5.0
2.5
EEUHD1H3R3( )
200
2000
4.7
5
11
26
0.12
1000
0.5
2.0
5.0
2.5
EEUHD1H4R7( )
200
2000
10
5
11
39
0.12
1000
0.5
2.0
5.0
2.5
EEUHD1H100( )
200
2000
22
5
11
65
0.12
1000
0.5
2.0
5.0
2.5
EEUHD1H220( )
200
2000
33
5
11
90
0.12
1000
0.5
2.0
5.0
2.5
EEUHD1H330( )
200
2000
47
6.3
11.2
110
0.12
1000
0.5
2.5
5.0
2.5
EEUHD1H470( )
200
2000
68
2.5
6.3
11.2
110
0.12
1000
0.5
2.5
5.0
EEUHD1H680( )
200
2000
100
8
11.5
180
0.12
1000
0.6
3.5
5.0
EEUHD1H101( )
200
1000
220
10
12.5
300
0.12
2000
0.6
5.0
5.0
EEUHD1H221( )
200
500
330
10
16
410
0.12
2000
0.6
5.0
5.0
EEUHD1H331( )
200
500
470
10
20
530
0.12
2000
0.6
5.0
5.0
EEUHD1H471( )
200
500
560
16
15
650
0.12
2000
0.8
7.5
7.5
EEUHD1H561S( )
100
250
680
16
15
650
0.12
2000
0.8
7.5
7.5
EEUHD1H681S( )
100
250
5.0
500
1000
12.5
25
950
0.12
2000
0.6
5.0
EEUHD1H102( )
200
2200
16
31.5
1470
0.14
2000
0.8
7.5
EEUHD1H222
100
3300
18
35.5
1770
0.16
2000
0.8
7.5
EEUHD1H332
50
· When requesting taped product, please put the letter “B” or “H” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, H=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : NHG Type : A
Features
● Endurance
● RoHS
: 105 °C 1000 h to 2000 h
compliant
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
–55 °C to +105 °C
6.3 V.DC to 100 V.DC
2.2 µF to 22000 µF
–25 °C to +105 °C
160 V.DC to 450 V.DC
1 µF to 330 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV or 3 (µA) After 2 minutes
(Which is greater)
Leakage current
Dissipation factor (tan d)
I < 0.06 CV +10 (µA) After 2 minutes
Please see the attached characteristics list
After following life test with DC voltage and +105 °C±2 °C ripple current value applied (The
sum of DC and ripple peak voltage shall not exceed the rated working voltage), When the
capacitors are restored to 20 °C, the capacitors shall meet the limits specified below.
Endurance
Shelf life
Duration : 6.3 V.DC to 100 V.DC : (05 to 08)=1000 hours, (010 to 018)=2000 hours
160 V.DC to 450 V.DC : 2000 hours
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Frequency correction factor for ripple current
Capacitance
(µF)
Rated voltage
(V.DC)
6.3 to 100
160 to 450
2.2
47
1000
1
60
0.75
0.80
0.85
0.80
to
33
to
470
to 22000
to
330
120
1.00
1.00
1.00
1.00
Frequency (Hz)
1k
1.55
1.35
1.10
1.35
10 k
1.80
1.50
1.15
1.50
< 08
010<
100 k
2.00
1.50
1.15
1.50
fd±0.05
Dimensions
Sleeve
Pressure relief
06.3 <
+
L✽
14 min.
0D±0.5
3 min.
F±0.5
–
0D±0.5
✽ L < 16 : L±1.0
L > 20 : L±2.0
(Unit : mm)
0D
5
6.3
8
10
12.5
16
18
0d
0.5
0.5
0.6
0.6
0.6
0.8
0.8
F
2.0
2.5
3.5
5.0
5.0
7.5
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
0D
L
220
470
1000
2200
3300
4700
6800
10000
15000
22000
330
470
1000
2200
3300
4700
6800
10000
15000
100
220
330
470
1000
2200
3300
4700
6800
10000
47
100
220
330
470
1000
2200
3300
4700
6800
47
100
220
330
470
1000
2200
3300
4700
5
6.3
8
10
10
12.5
12.5
16
16
18
6.3
8
10
10
12.5
12.5
16
16
18
5
6.3
8
8
10
12.5
12.5
16
16
18
5
6.3
8
8
10
10
12.5
16
16
18
5
6.3
8
10
10
12.5
16
16
18
11
11.2
11.5
16
20
20
25
25
31.5
35.5
11.2
11.5
12.5
20
20
25
25
31.5
35.5
11
11.2
11.5
11.5
16
20
25
25
31.5
35.5
11
11.2
11.5
11.5
12.5
20
25
25
31.5
35.5
11
11.2
11.5
12.5
16
20
25
31.5
35.5
6.3
10
16
25
35
Specification
Lead length (mm)
Ripple
Lead space
Lead
current tan d
Endurance
dia.
(120 Hz) (120 Hz)
Taping Taping
(hours)
(+105 °C) (+20 °C)
0d Straight ✽B
✽i
(mA r.m.s.)
140
0.28 1000
0.5
2.0
5.0
2.5
230
0.28 1000
0.5
2.5
5.0
2.5
380
0.28 1000
0.6
3.5
5.0
710
0.30 2000
0.6
5.0
5.0
840
0.32 2000
0.6
5.0
5.0
1090
0.34 2000
0.6
5.0
5.0
1350
0.38 2000
0.6
5.0
5.0
1650
0.46 2000
0.8
7.5
7.5
2010
0.56 2000
0.8
7.5
2350
0.70 2000
0.8
7.5
200
0.24 1000
0.5
2.5
5.0
2.5
250
0.24 1000
0.6
3.5
5.0
460
0.24 2000
0.6
5.0
5.0
760
0.26 2000
0.6
5.0
5.0
1000
0.28 2000
0.6
5.0
5.0
1260
0.30 2000
0.6
5.0
5.0
1570
0.34 2000
0.8
7.5
7.5
1890
0.42 2000
0.8
7.5
2180
0.52 2000
0.8
7.5
110
0.20 1000
0.5
2.0
5.0
2.5
180
0.20 1000
0.5
2.5
5.0
2.5
260
0.20 1000
0.6
3.5
5.0
310
0.20 1000
0.6
3.5
5.0
560
0.20 2000
0.6
5.0
5.0
920
0.22 2000
0.6
5.0
5.0
1170
0.24 2000
0.6
5.0
5.0
1480
0.26 2000
0.8
7.5
7.5
1780
0.30 2000
0.8
7.5
2060
0.38 2000
0.8
7.5
91
0.16 1000
0.5
2.0
5.0
2.5
130
0.16 1000
0.5
2.5
5.0
2.5
230
0.16 1000
0.6
3.5
5.0
310
0.16 1000
0.6
3.5
5.0
380
0.16 2000
0.6
5.0
5.0
680
0.16 2000
0.6
5.0
5.0
1090
0.18 2000
0.6
5.0
5.0
1400
0.20 2000
0.8
7.5
7.5
1750
0.22 2000
0.8
7.5
2040
0.26 2000
0.8
7.5
90
0.14 1000
0.5
2.0
5.0
2.5
150
0.14 1000
0.5
2.5
5.0
2.5
270
0.14 1000
0.6
3.5
5.0
350
0.14 2000
0.6
5.0
5.0
460
0.14 2000
0.6
5.0
5.0
810
0.14 2000
0.6
5.0
5.0
1260
0.16 2000
0.8
7.5
7.5
1610
0.18 2000
0.8
7.5
1910
0.20 2000
0.8
7.5
Min. Packaging Q'ty
Part No.
Straight
Taping
leads
(pcs)
(pcs)
ECA0JHG221( )
ECA0JHG471( )
ECA0JHG102( )
ECA0JHG222( )
ECA0JHG332( )
ECA0JHG472( )
ECA0JHG682( )
ECA0JHG103( )
ECA0JHG153
ECA0JHG223
ECA1AHG331( )
ECA1AHG471( )
ECA1AHG102( )
ECA1AHG222( )
ECA1AHG332( )
ECA1AHG472( )
ECA1AHG682( )
ECA1AHG103
ECA1AHG153
ECA1CHG101( )
ECA1CHG221( )
ECA1CHG331( )
ECA1CHG471( )
ECA1CHG102( )
ECA1CHG222( )
ECA1CHG332( )
ECA1CHG472( )
ECA1CHG682
ECA1CHG103
ECA1EHG470( )
ECA1EHG101( )
ECA1EHG221( )
ECA1EHG331( )
ECA1EHG471( )
ECA1EHG102( )
ECA1EHG222( )
ECA1EHG332( )
ECA1EHG472
ECA1EHG682
ECA1VHG470( )
ECA1VHG101( )
ECA1VHG221( )
ECA1VHG331( )
ECA1VHG471( )
ECA1VHG102( )
ECA1VHG222( )
ECA1VHG332
ECA1VHG472
200
200
200
200
200
200
200
100
100
50
200
200
200
200
200
200
100
100
50
200
200
200
200
200
200
200
100
100
50
200
200
200
200
200
200
200
100
100
50
200
200
200
200
200
200
100
100
50
2000
2000
1000
500
500
500
500
250
2000
1000
500
500
500
500
250
2000
2000
1000
1000
500
500
500
250
2000
2000
1000
1000
500
500
500
250
2000
2000
1000
500
500
500
250
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
2.2
50
63
100
0D
5
L
11
Specification
Lead length (mm)
Ripple
Lead space
Lead
current tan d
Part No.
Endurance
dia.
(120 Hz) (120 Hz)
Taping Taping
(hours)
Straight
(+105 °C) (+20 °C)
0d
✽B
✽i
(mA r.m.s.)
18
0.12 1000
0.5
2.0
5.0
2.5
ECA1HHG2R2( )
Min. Packaging Q'ty
Straight
Taping
leads
(pcs)
(pcs)
200
2000
3.3
5
11
22
0.12
1000
0.5
2.0
5.0
2.5
ECA1HHG3R3( )
200
2000
4.7
5
11
26
0.12
1000
0.5
2.0
5.0
2.5
ECA1HHG4R7( )
200
2000
10
5
11
39
0.12
1000
0.5
2.0
5.0
2.5
ECA1HHG100( )
200
2000
22
5
11
65
0.12
1000
0.5
2.0
5.0
2.5
ECA1HHG220( )
200
2000
33
5
11
47
6.3
11.2
90
0.12
1000
0.5
2.0
5.0
2.5
ECA1HHG330( )
200
2000
110
0.12
1000
0.5
2.5
5.0
2.5
ECA1HHG470( )
200
2000
100
8
220
10
11.5
180
0.12
1000
0.6
3.5
5.0
ECA1HHG101( )
200
1000
12.5
300
0.12
2000
0.6
5.0
5.0
ECA1HHG221( )
200
500
330
10
16
410
0.12
2000
0.6
5.0
5.0
ECA1HHG331( )
200
500
470
10
20
530
0.12
2000
0.6
5.0
5.0
ECA1HHG471( )
200
500
5.0
500
1000
12.5
25
950
0.12
2000
0.6
5.0
ECA1HHG102( )
200
2200
16
31.5
1470
0.14
2000
0.8
7.5
ECA1HHG222
100
3300
18
35.5
1770
0.16
2000
0.8
7.5
ECA1HHG332
50
10
5
11
46
0.10
1000
0.5
2.0
5.0
2.5
ECA1JHG100( )
200
2000
22
5
11
71
0.10
1000
0.5
2.0
5.0
2.5
ECA1JHG220( )
200
2000
33
6.3
11.2
100
0.10
1000
0.5
2.5
5.0
2.5
ECA1JHG330( )
200
2000
47
6.3
11.2
120
0.10
1000
0.5
2.5
5.0
2.5
ECA1JHG470( )
200
2000
100
10
12.5
215
0.10
2000
0.6
5.0
5.0
ECA1JHG101( )
200
500
220
10
16
335
0.10
2000
0.6
5.0
5.0
ECA1JHG221( )
200
500
330
10
20
510
0.10
2000
0.6
5.0
5.0
ECA1JHG331( )
200
500
470
12.5
20
640
0.10
2000
0.6
5.0
5.0
ECA1JHG471( )
200
500
1000
16
25
7.5
ECA1JHG102( )
100
250
2200
18
35.5
930
0.10
2000
0.8
7.5
1610
0.12
2000
0.8
7.5
21
0.08
1000
0.5
2.0
5.0
2.5
ECA2AHG2R2( )
200
2000
ECA1JHG222
50
2.2
5
11
3.3
5
11
31
0.08
1000
0.5
2.0
5.0
2.5
ECA2AHG3R3( )
200
2000
4.7
5
11
38
0.08
1000
0.5
2.0
5.0
2.5
ECA2AHG4R7( )
200
2000
10
6.3
11.2
54
0.08
1000
0.5
2.5
5.0
2.5
ECA2AHG100( )
200
2000
22
6.3
11.2
93
0.08
1000
0.5
2.5
5.0
2.5
ECA2AHG220( )
200
2000
33
8
11.5
130
0.08
1000
0.6
3.5
5.0
ECA2AHG330( )
200
1000
47
10
12.5
165
0.08
2000
0.6
5.0
5.0
ECA2AHG470( )
200
500
100
10
20
265
0.08
2000
0.6
5.0
5.0
ECA2AHG101( )
200
500
220
12.5
25
440
0.08
2000
0.6
5.0
5.0
ECA2AHG221( )
200
500
330
16
25
540
0.08
2000
0.8
7.5
7.5
ECA2AHG331( )
100
250
470
16
25
715
0.08
2000
0.8
7.5
7.5
ECA2AHG471( )
100
250
1000
18
35.5
985
0.08
2000
0.8
7.5
ECA2AHG102
50
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
0D
L
1
2.2
3.3
4.7
10
22
33
47
100
220
330
1
2.2
3.3
4.7
10
22
33
47
100
220
1
2.2
3.3
4.7
10
22
33
47
100
1
2.2
3.3
4.7
10
22
33
47
100
6.3
6.3
6.3
6.3
10
10
10
12.5
16
16
18
6.3
6.3
6.3
8
10
10
12.5
12.5
16
18
6.3
6.3
8
8
10
12.5
12.5
12.5
16
6.3
8
10
10
10
12.5
16
16
18
11.2
11.2
11.2
11.2
12.5
20
20
20
25
31.5
31.5
11.2
11.2
11.2
11.5
16
20
20
20
25
31.5
11.2
11.2
11.5
11.5
16
20
20
25
31.5
11.2
11.5
12.5
16
20
20
25
25
31.5
160
200
250
350
Specification
Lead length (mm)
Ripple
Lead space
current tan d
Lead
Endurance
dia.
(120 Hz) (120 Hz)
Taping Taping
(hours)
(+105 °C) (+20 °C)
0d Straight ✽B
✽i
(mA r.m.s.)
17 0.15 2000
0.5
2.5
5.0
2.5
25 0.15 2000
0.5
2.5
5.0
2.5
36 0.15 2000
0.5
2.5
5.0
2.5
43 0.15 2000
0.5
2.5
5.0
2.5
70 0.15 2000
0.6
5.0
5.0
130 0.15 2000
0.6
5.0
5.0
180 0.15 2000
0.6
5.0
5.0
220 0.15 2000
0.6
5.0
5.0
335 0.15 2000
0.8
7.5
7.5
540 0.15 2000
0.8
7.5
705 0.15 2000
0.8
7.5
17 0.15 2000
0.5
2.5
5.0
2.5
25 0.15 2000
0.5
2.5
5.0
2.5
36 0.15 2000
0.5
2.5
5.0
2.5
50 0.15 2000
0.6
3.5
5.0
80 0.15 2000
0.6
5.0
5.0
140 0.15 2000
0.6
5.0
5.0
190 0.15 2000
0.6
5.0
5.0
220 0.15 2000
0.6
5.0
5.0
335 0.15 2000
0.8
7.5
7.5
575 0.15 2000
0.8
7.5
17 0.15 2000
0.5
2.5
5.0
2.5
29 0.15 2000
0.5
2.5
5.0
2.5
42 0.15 2000
0.6
3.5
5.0
50 0.15 2000
0.6
3.5
5.0
88 0.15 2000
0.6
5.0
5.0
155 0.15 2000
0.6
5.0
5.0
190 0.15 2000
0.6
5.0
5.0
230 0.15 2000
0.6
5.0
5.0
365 0.15 2000
0.8
7.5
18 0.20 2000
0.5
2.5
5.0
2.5
31 0.20 2000
0.6
3.5
5.0
38 0.20 2000
0.6
5.0
5.0
50 0.20 2000
0.6
5.0
5.0
82 0.20 2000
0.6
5.0
5.0
130 0.20 2000
0.6
5.0
5.0
195 0.20 2000
0.8
7.5
7.5
230 0.20 2000
0.8
7.5
7.5
375 0.20 2000
0.8
7.5
Min. Packaging Q'ty
Part No.
Straight
Taping
leads
(pcs)
(pcs)
ECA2CHG010( )
ECA2CHG2R2( )
ECA2CHG3R3( )
ECA2CHG4R7( )
ECA2CHG100( )
ECA2CHG220( )
ECA2CHG330( )
ECA2CHG470( )
ECA2CHG101( )
ECA2CHG221
ECA2CHG331
ECA2DHG010( )
ECA2DHG2R2( )
ECA2DHG3R3( )
ECA2DHG4R7( )
ECA2DHG100( )
ECA2DHG220( )
ECA2DHG330( )
ECA2DHG470( )
ECA2DHG101( )
ECA2DHG221
ECA2EHG010( )
ECA2EHG2R2( )
ECA2EHG3R3
ECA2EHG4R7( )
ECA2EHG100( )
ECA2EHG220( )
ECA2EHG330( )
ECA2EHG470( )
ECA2EHG101
ECA2VHG010( )
ECA2VHG2R2( )
ECA2VHG3R3( )
ECA2VHG4R7( )
ECA2VHG100( )
ECA2VHG220( )
ECA2VHG330( )
ECA2VHG470( )
ECA2VHG101
200
200
200
200
200
200
200
200
100
100
50
200
200
200
200
200
200
200
200
100
50
200
200
200
200
200
200
200
200
100
200
200
200
200
200
200
100
100
50
2000
2000
2000
2000
500
500
500
500
250
2000
2000
2000
1000
500
500
500
500
250
2000
2000
1000
1000
500
500
500
500
2000
1000
500
500
500
500
250
250
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
1
400
450
0D
6.3
Specification
Lead length (mm)
Ripple
Lead space
Lead
current tan d
Part No.
Endurance
dia.
L
(120 Hz) (120 Hz)
Taping Taping
(hours)
Straight
(+105 °C) (+20 °C)
0d
✽B
✽i
(mA r.m.s.)
11.2
18
0.24 2000
0.5
2.5
5.0
2.5
ECA2GHG010( )
Min. Packaging Q'ty
Straight
Taping
leads
(pcs)
(pcs)
200
2000
2.2
8
11.5
30
0.24
2000
0.6
3.5
5.0
ECA2GHG2R2( )
200
1000
3.3
10
12.5
40
0.24
2000
0.6
5.0
5.0
ECA2GHG3R3( )
200
500
4.7
10
16
50
0.24
2000
0.6
5.0
5.0
ECA2GHG4R7( )
200
500
10
20
80
0.24
2000
0.6
5.0
5.0
ECA2GHG100( )
200
500
10
22
12.5
25
145
0.24
2000
0.6
5.0
5.0
ECA2GHG220( )
200
500
33
16
25
195
0.24
2000
0.8
7.5
7.5
ECA2GHG330( )
100
250
47
16
31.5
250
0.24
2000
0.8
7.5
ECA2GHG470
100
1
8
11.5
18
0.24
2000
0.6
3.5
5.0
ECA2WHG010( )
200
1000
2.2
10
12.5
29
0.24
2000
0.6
5.0
5.0
ECA2WHG2R2( )
200
500
3.3
10
16
41
0.24
2000
0.6
5.0
5.0
ECA2WHG3R3( )
200
500
4.7
10
20
49
0.24
2000
0.6
5.0
5.0
ECA2WHG4R7( )
200
500
10
12.5
20
75
0.24
2000
0.6
5.0
5.0
ECA2WHG100( )
200
500
22
16
25
115
0.24
2000
0.8
7.5
7.5
ECA2WHG220( )
100
250
33
16
31.5
155
0.24
2000
0.8
7.5
ECA2WHG330
100
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : GA Type : A
Features
● Endurance
● RoHS
: 105 °C 1000 h
compliant
Specifications
Category temperature range
Rated voltage range
Capacitance range
Capacitance tolerance
Leakage current
Dissipation factor (tan d)
–55 °C to +105 °C
10 V.DC to 50 V.DC
1.5 µF to 220 µF
±20 % (120 Hz/+20 °C)
I < 0.01 CV or 3 (µA) After 2 minutes (Whichever is greater)
Please see the attached characteristics list
After following life test with DC voltage and +105 °C±2 °C ripple current value applied (The sum
of DC and ripple peak voltage shall not exceed the rated working voltage), for 1000 hours, when
the capacitors are restored to 20 °C, the capacitors shall meet the limits specified below.
Endurance
Shelf life
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Frequency correction factor for ripple current
Frequency (Hz)
60
120
1k
10 k
100 k to
Correction factor
0.85
1.00
1.30
1.40
1.55
Sleeve
fd±0.05
Dimensions
+
L±1.0
14 min.
3 min.
0D±0.5
F±0.5
–
(Unit : mm)
0D
4
5
6.3
8
0d
0.45
0.45
0.45
0.45
F
1.5
2.0
2.5
2.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 105 °C 1000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
10
16
25
22
4
7
5
7
50
0.22
1000
0.45
2.0
5.0
2.5
EEAGA1A330( )
Min. Packaging Q'ty
Straight
Taping
leads
(pcs)
(pcs)
200
2000
200
2000
47
6.3
7
65
0.22
1000
0.45
2.5
5.0
2.5
EEAGA1A470( )
200
2000
68
6.3
7
75
0.22
1000
0.45
2.5
5.0
2.5
EEAGA1A680( )
200
2000
100
6.3
7
110
0.22
1000
0.45
2.5
5.0
2.5
EEAGA1A101( )
200
2000
220
8
7
160
0.22
1000
0.45
2.5
5.0
2.5
EEAGA1A221( )
200
1000
10
4
7
30
0.18
1000
0.45
1.5
5.0
2.5
EEAGA1C100( )
200
2000
15
4
7
33
0.18
1000
0.45
1.5
5.0
2.5
EEAGA1C150( )
200
2000
22
5
7
50
0.18
1000
0.45
2.0
5.0
2.5
EEAGA1C220( )
200
2000
33
6.3
7
65
0.18
1000
0.45
2.5
5.0
2.5
EEAGA1C330( )
200
2000
47
6.3
7
77
0.18
1000
0.45
2.5
5.0
2.5
EEAGA1C470( )
200
2000
100
8
7
120
0.18
1000
0.45
2.5
5.0
2.5
EEAGA1C101( )
200
1000
10
4
7
33
0.16
1000
0.45
1.5
5.0
2.5
EEAGA1E100( )
200
2000
15
5
7
45
0.16
1000
0.45
2.0
5.0
2.5
EEAGA1E150( )
200
2000
22
5
7
50
0.16
1000
0.45
2.0
5.0
2.5
EEAGA1E220( )
200
2000
33
6.3
7
75
0.16
1000
0.45
2.5
5.0
2.5
EEAGA1E330( )
200
2000
8
7
100
0.16
1000
0.45
2.5
5.0
2.5
EEAGA1E680( )
200
1000
4
7
33
0.13
1000
0.45
1.5
5.0
2.5
EEAGA1V6R8( )
200
2000
6.8
50
L
33
68
35
0D
Specification
Lead length (mm)
Ripple
Lead space
Lead
current tan d
Part No.
Endurance
dia.
(120 Hz) (120 Hz)
Taping Taping
(hours)
Straight
(+105 °C) (+20 °C)
0d
✽B
✽H
(mA r.m.s.)
30
0.22 1000 0.45
1.5
5.0
2.5
EEAGA1A220( )
10
5
7
35
0.13
1000
0.45
2.0
5.0
2.5
EEAGA1V100( )
200
2000
15
6.3
7
50
0.13
1000
0.45
2.5
5.0
2.5
EEAGA1V150( )
200
2000
22
6.3
7
70
0.13
1000
0.45
2.5
5.0
2.5
EEAGA1V220( )
200
2000
47
8
7
96
0.13
1000
0.45
2.5
5.0
2.5
EEAGA1V470( )
200
1000
1.5
4
7
16
0.10
1000
0.45
1.5
5.0
2.5
EEAGA1H1R5( )
200
2000
2.2
4
7
18
0.10
1000
0.45
1.5
5.0
2.5
EEAGA1H2R2( )
200
2000
3.3
4
7
22
0.10
1000
0.45
1.5
5.0
2.5
EEAGA1H3R3( )
200
2000
4.7
4
7
26
0.10
1000
0.45
1.5
5.0
2.5
EEAGA1H4R7( )
200
2000
5
7
35
0.10
1000
0.45
2.0
5.0
2.5
EEAGA1H6R8( )
200
2000
10
6.8
6.3
7
39
0.10
1000
0.45
2.5
5.0
2.5
EEAGA1H100( )
200
2000
15
6.3
7
55
0.10
1000
0.45
2.5
5.0
2.5
EEAGA1H150( )
200
2000
22
8
7
70
0.10
1000
0.45
2.5
5.0
2.5
EEAGA1H220( )
200
1000
33
8
7
91
0.10
1000
0.45
2.5
5.0
2.5
EEAGA1H330( )
200
1000
· When requesting taped product, please put the letter "B" or "H" between the "( )". Lead wire pitch ✽B=5 mm, H=2.5 mm.
Suffix "BQ" for 08×7, 5 mm pitch products
· Please refer to the page of “Taping Dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : GA (Bi-polar) Type : A
Features
● Endurance
● RoHS
: 105 °C 1000 h to 2000 h
compliant
Specifications
Category temperature range
–40 °C to +105 °C
Rated voltage range
6.3 V.DC to 50 V.DC
Capacitance range
2.2 µF to 330 µF
Capacitance tolerance
±20 % (120 Hz/+20 °C)
I < 0.03 CV +3 (µA) After 2 minutes
Leakage current
or
I < 0.03 CV or 3 (µA) After 5 minutes (Whichever is greater)
Dissipation factor (tan d)
Please see the attached characteristics list
After following life test of DC working voltage at +105 °C±2 °C
when the capacitors are restored to 20 °C, the capacitors shall meet the following limits.
Duration
05 to 08 : 1000 hours (500 hours for each polarity)
Endurance
010
: 2000 hours (1000 hours for each polarity)
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current
Within the initial limit
After storage for 1000 hours at +105 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Shelf life
Frequency correction factor for ripple current
Frequency (Hz)
50, 60
120
1k
10 k to
Correction factor
0.70
1.00
1.30
1.70
fd±0.05
Dimensions
L✽
14 min.
< 08
0D±0.5
3 min.
010 <
F±0.5
Sleeve
Pressure relief
06.3 <
0D±0.5
✽ L < 16 : L±1.0
L > 20 : L±2.0
(Unit : mm)
0D
5
6.3
8
10
0d
0.5
0.5
0.6
0.6
F
2.0
2.5
3.5
5.0
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list (Bi-polar)
Endurance : 105 °C 05 to 08=1000 h (500 h for each polarity), 010=2000 h (1000 h for each polarity)
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
6.3
10
16
25
35
L
100
6.3
11.2
330
8
11.5
47
5
11
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
0d
Part No.
Taping Taping
Straight
✽B
✽i
0.5
2.5
5.0
250
0.30
0.6
3.5
5.0
90
0.24
0.5
2.0
5.0
2.5
2.5
Straight
Taping
leads
(pcs)
(pcs)
ECA0JEN101( )
200
2000
ECA0JEN331( )
200
1000
ECA1AEN470( )
200
2000
10
5
11
40
0.20
0.5
2.0
5.0
2.5
ECA1CEN100( )
200
2000
22
5
11
60
0.20
0.5
2.0
5.0
2.5
ECA1CEN220( )
200
2000
33
5
11
80
0.20
0.5
2.0
5.0
2.5
ECA1CEN330( )
200
2000
47
6.3
11.2
100
0.20
0.5
2.5
5.0
2.5
ECA1CEN470( )
200
2000
10
5
11
45
0.15
0.5
2.0
5.0
2.5
ECA1EEN100( )
200
2000
22
6.3
11.2
60
0.15
0.5
2.5
5.0
2.5
ECA1EEN220( )
200
2000
33
6.3
11.2
90
0.15
0.5
2.5
5.0
2.5
ECA1EEN330( )
200
2000
47
6.3
11.2
110
0.15
0.5
2.5
5.0
2.5
ECA1EEN470( )
200
2000
100
8
11.5
180
0.15
0.6
3.5
5.0
ECA1EEN101( )
200
1000
33
8
11.5
100
0.15
0.6
3.5
5.0
ECA1VEN330( )
200
1000
100
10
16
230
0.15
0.6
5.0
5.0
ECA1VEN101( )
200
500
2.2
5
11
18
0.15
0.5
2.0
5.0
2.5
ECA1HEN2R2( )
200
2000
3.3
5
11
25
0.15
0.5
2.0
5.0
2.5
ECA1HEN3R3( )
200
2000
5
11
30
0.15
0.5
2.0
5.0
2.5
ECA1HEN4R7( )
200
2000
6.3
11.2
50
0.15
0.5
2.5
5.0
2.5
ECA1HEN100( )
200
2000
4.7
50
0D
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+105 °C) (+20 °C)
(mA r.m.s.)
130
0.30
10
22
8
11.5
90
0.15
0.6
3.5
5.0
ECA1HEN220( )
200
1000
33
8
11.5
110
0.15
0.6
3.5
5.0
ECA1HEN330( )
200
1000
47
10
12.5
140
0.15
0.6
5.0
5.0
ECA1HEN470( )
200
500
100
10
20
250
0.15
0.6
5.0
5.0
ECA1HEN101( )
200
500
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : M Type : A
Features
● Endurance
: 85 °C 2000 h
than series SU
● RoHS compliant
● Smaller
Specifications
Category temperature range
–40 °C to + 85 °C
–25 °C to +85 °C
Rated voltage range
6.3 V.DC to 100 V.DC
160 V.DC to 450 V.DC
Capacitance range
2.2 µF to 22000 µF
1 µF to 470 µF
Capacitance tolerance
±20 % (120 Hz/+20 °C)
I < 0.01 CV or 3 (µA) After 2 minutes
(Whichever is greater)
Leakage current
Dissipation factor (tan d)
I < 0.06 CV +10 (µA) After 2 minutes
Please see the attached characteristics list
After applying rated working voltage for 2000 hours at +85°C±2 °C, when the capacitors are
restored to 20 °C, capacitors shall meet the following limits.
Endurance
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current
Within the initial limit
After storage for 1000 hours at +85 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Shelf life
Frequency correction factor for ripple current
Frequency (Hz)
50, 60
120
1k
10 k to
Correction factor
0.70
1.00
1.30
1.70
fd±0.05
Dimensions
Sleeve
Pressure relief
06.3 <
< 08
010<
+
L✽
14 min.
0D+0.5
3 min.
F±0.5
–
0D+0.5
✽ L < 16 : L±1.0
L > 20 : L±2.0
(Unit : mm)
0D
5
6.3
8
10
12.5
16
18
0d
0.5
0.5
0.6
0.6
0.6
0.8
0.8
F
2.0
2.5
3.5
5.0
5.0
7.5
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 85 °C 2000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
16
25
Min. Packaging Q'ty
Lead space
Lead
dia.
0d
Part No.
Taping Taping
Straight
✽B
✽i
Straight
Taping
leads
(pcs)
(pcs)
5
11
0.5
2.0
5.0
2.5
ECA0JM221( )
200
2000
470
6.3
11.2
380
0.28
0.5
2.5
5.0
2.5
ECA0JM471( )
200
2000
8
11.5
580
0.28
0.6
3.5
5.0
ECA0JM102( )
200
1000
2200
10
16
890
0.30
0.6
5.0
5.0
ECA0JM222( )
200
500
3300
10
20
1020
0.32
0.6
5.0
5.0
ECA0JM332( )
200
500
4700
12.5
20
1170
0.34
0.6
5.0
5.0
ECA0JM472( )
200
500
6800
12.5
25
1270
0.38
0.6
5.0
5.0
ECA0JM682( )
200
500
7.5
ECA0JM103( )
100
250
ECA0JM153
100
10000
16
25
1450
0.46
0.8
7.5
15000
16
31.5
1700
0.56
0.8
7.5
22000
18
330
10
L
Lead length (mm)
220
1000
6.3
0D
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
240
0.28
6.3
35.5
1900
0.70
0.8
7.5
11.2
330
0.24
0.5
2.5
5.0
ECA0JM223
2.5
ECA1AM331( )
50
200
2000
1000
10
12.5
630
0.24
0.6
5.0
5.0
ECA1AM102( )
200
500
2200
10
20
920
0.26
0.6
5.0
5.0
ECA1AM222( )
200
500
3300
12.5
20
1090
0.28
0.6
5.0
5.0
ECA1AM332( )
200
500
4700
12.5
25
1200
0.30
0.6
5.0
5.0
ECA1AM472( )
200
500
6800
16
25
1400
0.34
0.8
7.5
7.5
ECA1AM682( )
100
250
10000
16
31.5
1600
0.42
0.8
7.5
ECA1AM103
100
15000
18
35.5
1850
0.52
0.8
7.5
ECA1AM153
50
10
5
11
30
0.20
0.5
2.0
5.0
2.5
ECA1CM100( )
200
2000
22
5
11
75
0.20
0.5
2.0
5.0
2.5
ECA1CM220( )
200
2000
33
5
11
110
0.20
0.5
2.0
5.0
2.5
ECA1CM330( )
200
2000
47
5
11
130
0.20
0.5
2.0
5.0
2.5
ECA1CM470( )
200
2000
100
5
11
180
0.20
0.5
2.0
5.0
2.5
ECA1CM101( )
200
2000
220
6.3
11.2
280
0.20
0.5
2.5
5.0
2.5
ECA1CM221( )
200
2000
470
8
11.5
440
0.20
0.6
3.5
5.0
ECA1CM471( )
200
1000
1000
10
16
680
0.20
0.6
5.0
5.0
ECA1CM102( )
200
500
2200
12.5
20
1000
0.22
0.6
5.0
5.0
ECA1CM222( )
200
500
3300
12.5
25
1200
0.24
0.6
5.0
5.0
ECA1CM332( )
200
500
4700
16
25
1360
0.26
0.8
7.5
7.5
ECA1CM472( )
100
250
6800
16
31.5
1600
0.30
0.8
7.5
ECA1CM682
100
10000
18
35.5
1800
0.38
0.8
7.5
ECA1CM103
50
100
6.3
11.2
180
0.16
0.5
2.5
5.0
ECA1EM101( )
200
2000
330
8
11.5
390
0.16
0.6
3.5
5.0
2.5
ECA1EM331( )
200
1000
470
10
12.5
480
0.16
0.6
5.0
5.0
ECA1EM471( )
200
500
1000
10
20
850
0.16
0.6
5.0
5.0
ECA1EM102( )
200
500
2200
12.5
25
1200
0.18
0.6
5.0
5.0
ECA1EM222( )
200
500
3300
16
25
1300
0.20
0.8
7.5
7.5
ECA1EM332( )
100
250
4700
16
31.5
1500
0.22
0.8
7.5
ECA1EM472
100
6800
18
35.5
1750
0.26
0.8
7.5
ECA1EM682
50
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 85 °C 2000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
47
100
35
50
63
0D
L
5
11
6.3
11.2
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
130
0.14
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
0d
Part No.
Taping Taping
Straight
✽B
✽i
Straight
Taping
leads
(pcs)
(pcs)
0.5
2.0
5.0
2.5
ECA1VM470( )
200
2000
210
0.14
0.5
2.5
5.0
2.5
ECA1VM101( )
200
2000
220
8
11.5
350
0.14
0.6
3.5
5.0
ECA1VM221( )
200
1000
330
10
12.5
440
0.14
0.6
5.0
5.0
ECA1VM331( )
200
500
470
10
16
550
0.14
0.6
5.0
5.0
ECA1VM471( )
200
500
1000
12.5
20
900
0.14
0.6
5.0
5.0
ECA1VM102( )
200
500
2200
16
25
1250
0.16
0.8
7.5
7.5
ECA1VM222( )
100
250
3300
16
31.5
1400
0.18
0.8
7.5
ECA1VM332
100
4700
18
35.5
1600
0.20
0.8
7.5
ECA1VM472
50
2.2
5
11
20
0.12
0.5
2.0
5.0
2.5
ECA1HM2R2( )
200
2000
3.3
5
11
35
0.12
0.5
2.0
5.0
2.5
ECA1HM3R3( )
200
2000
4.7
5
11
45
0.12
0.5
2.0
5.0
2.5
ECA1HM4R7( )
200
2000
10
5
11
65
0.12
0.5
2.0
5.0
2.5
ECA1HM100( )
200
2000
22
5
11
100
0.12
0.5
2.0
5.0
2.5
ECA1HM220( )
200
2000
33
5
11
110
0.12
0.5
2.0
5.0
2.5
ECA1HM330( )
200
2000
47
6.3
11.2
130
0.12
0.5
2.5
5.0
2.5
ECA1HM470( )
200
2000
100
8
11.5
250
0.12
0.6
3.5
5.0
ECA1HM101( )
200
1000
220
10
12.5
400
0.12
0.6
5.0
5.0
ECA1HM221( )
200
500
330
10
16
500
0.12
0.6
5.0
5.0
ECA1HM331( )
200
500
470
10
20
650
0.12
0.6
5.0
5.0
ECA1HM471( )
200
500
5.0
ECA1HM102( )
200
500
ECA1HM222
100
1000
12.5
25
1050
0.12
0.6
5.0
2200
16
31.5
1300
0.14
0.8
7.5
3300
18
35.5
1500
0.16
0.8
7.5
10
5
11
70
0.11
0.5
2.0
ECA1HM332
5.0
2.5
ECA1JM100( )
50
200
2000
22
5
11
105
0.11
0.5
2.0
5.0
2.5
ECA1JM220( )
200
2000
33
6.3
11.2
130
0.11
0.5
2.5
5.0
2.5
ECA1JM330( )
200
2000
47
2.5
6.3
11.2
160
0.11
0.5
2.5
5.0
ECA1JM470( )
200
2000
100
8
11.5
270
0.11
0.6
3.5
5.0
ECA1JM101( )
200
1000
220
10
16
450
0.11
0.6
5.0
5.0
ECA1JM221( )
200
500
330
10
20
550
0.11
0.6
5.0
5.0
ECA1JM331( )
200
500
470
12.5
20
750
0.11
0.6
5.0
5.0
ECA1JM471( )
200
500
7.5
ECA1JM102( )
100
250
1000
16
25
1100
0.11
0.8
7.5
2200
18
35.5
1400
0.13
0.8
7.5
ECA1JM222
50
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 85 °C 2000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
2.2
5
11
5
11
40
Min. Packaging Q'ty
Lead space
Lead
dia.
0d
Part No.
Taping Taping
Straight
✽B
✽i
Straight
Taping
leads
(pcs)
(pcs)
0.5
2.0
5.0
2.5
ECA2AM2R2( )
200
2000
0.5
2.0
5.0
2.5
ECA2AM3R3( )
200
2000
5
11
50
0.10
0.5
2.0
5.0
2.5
ECA2AM4R7( )
200
2000
5
11
70
0.10
0.5
2.0
5.0
2.5
ECA2AM100( )
200
2000
22
6.3
11.2
115
0.10
0.5
2.5
5.0
2.5
ECA2AM220( )
200
2000
33
8
11.5
145
0.10
0.6
3.5
5.0
ECA2AM330( )
200
1000
47
8
11.5
180
0.10
0.6
3.5
5.0
ECA2AM470( )
200
1000
100
10
16
350
0.10
0.6
5.0
5.0
ECA2AM101( )
200
500
220
12.5
20
550
0.10
0.6
5.0
5.0
ECA2AM221( )
200
500
330
12.5
25
700
0.10
0.6
5.0
5.0
ECA2AM331( )
200
500
470
16
25
900
0.10
0.8
7.5
7.5
ECA2AM471( )
100
250
1000
18
35.5
1300
0.10
0.8
7.5
11.2
36
0.16
0.5
2.5
5.0
2.5
ECA2CM010( )
200
2000
6.3
ECA2AM102
50
2.2
6.3
11.2
53
0.16
0.5
2.5
5.0
2.5
ECA2CM2R2( )
200
2000
3.3
6.3
11.2
66
0.16
0.5
2.5
5.0
2.5
ECA2CM3R3( )
200
2000
4.7
6.3
11.2
78
0.16
0.5
2.5
5.0
2.5
ECA2CM4R7( )
200
2000
10
10
12.5
105
0.16
0.6
5.0
5.0
ECA2CM100( )
200
500
22
10
16
175
0.16
0.6
5.0
5.0
ECA2CM220( )
200
500
33
10
20
235
0.16
0.6
5.0
5.0
ECA2CM330( )
200
500
47
12.5
20
320
0.16
0.6
5.0
5.0
ECA2CM470( )
200
500
5.0
500
100
12.5
25
515
0.16
0.6
5.0
ECA2CM101( )
200
220
16
31.5
830
0.16
0.8
7.5
ECA2CM221
100
330
18
31.5
1090
0.16
0.8
7.5
ECA2CM331
50
470
18
40
1440
0.16
0.8
7.5
ECA2CM471
50
1
6.3
11.2
34
0.18
0.5
2.5
5.0
2.5
ECA2DM010( )
200
2000
2.2
6.3
11.2
50
0.18
0.5
2.5
5.0
2.5
ECA2DM2R2( )
200
2000
3.3
6.3
11.2
62
0.18
0.5
2.5
5.0
2.5
ECA2DM3R3( )
200
2000
4.7
8
11.5
86
0.18
0.6
3.5
5.0
ECA2DM4R7( )
200
1000
10
12.5
100
0.18
0.6
5.0
5.0
ECA2DM100( )
200
500
10
200
0.10
Lead length (mm)
10
1
160
L
3.3
4.7
100
0D
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
30
0.10
22
10
20
180
0.18
0.6
5.0
5.0
ECA2DM220( )
200
500
33
10
20
220
0.18
0.6
5.0
5.0
ECA2DM330( )
200
500
12.5
20
300
0.18
0.6
5.0
5.0
ECA2DM470( )
200
500
100
47
16
25
475
0.18
0.8
7.5
7.5
ECA2DM101( )
100
250
220
18
31.5
835
0.18
0.8
7.5
ECA2DM221
50
330
18
40
1140
0.18
0.8
7.5
ECA2DM331
50
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 85 °C 2000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
250
0D
L
1
6.3
11.2
2.2
6.3
11.2
3.3
8
4.7
8
Lead space
Lead
dia.
0d
Part No.
Taping Taping
Straight
✽B
✽i
Straight
Taping
leads
(pcs)
(pcs)
0.5
2.5
5.0
2.5
ECA2EM010( )
200
2000
50
0.18
0.5
2.5
5.0
2.5
ECA2EM2R2( )
200
2000
11.5
72
0.18
0.6
3.5
5.0
ECA2EM3R3( )
200
1000
11.5
86
0.18
0.6
3.5
5.0
ECA2EM4R7( )
200
1000
110
0.18
0.6
5.0
5.0
ECA2EM100( )
200
500
22
10
20
180
0.18
0.6
5.0
5.0
ECA2EM220( )
200
500
33
12.5
20
250
0.18
0.6
5.0
5.0
ECA2EM330( )
200
500
16
5.0
ECA2EM470( )
200
500
ECA2EM101
100
12.5
25
330
0.18
0.6
5.0
100
16
31.5
530
0.18
0.8
7.5
220
18
40
930
0.18
0.8
7.5
32
0.20
0.5
2.5
5.0
6.3
11.2
ECA2EM221
2.5
ECA2VM010( )
50
200
2000
2.2
8
11.5
55
0.20
0.6
3.5
5.0
ECA2VM2R2( )
200
1000
3.3
8
11.5
60
0.20
0.6
3.5
5.0
ECA2VM3R3( )
200
1000
4.7
10
12.5
65
0.20
0.6
5.0
5.0
ECA2VM4R7( )
200
500
10
10
20
115
0.20
0.6
5.0
5.0
ECA2VM100( )
200
500
22
12.5
20
195
0.20
0.6
5.0
5.0
ECA2VM220( )
200
500
33
16
25
300
0.20
0.8
7.5
7.5
ECA2VM330( )
100
250
47
16
25
325
0.20
0.8
7.5
7.5
ECA2VM470( )
100
250
100
18
31.5
535
0.20
0.8
7.5
6.3
11.2
32
0.20
0.5
2.5
2.2
8
11.5
50
0.20
0.6
3.5
5.0
3.3
10
12.5
54
0.20
0.6
5.0
5.0
1
4.7
450
Min. Packaging Q'ty
10
1
400
Lead length (mm)
10
47
350
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
34
0.18
10
ECA2VM101
5.0
2.5
ECA2GM010( )
50
200
2000
ECA2GM2R2( )
200
1000
ECA2GM3R3( )
200
500
10
16
72
0.20
0.6
5.0
5.0
ECA2GM4R7( )
200
500
10
20
115
0.20
0.6
5.0
5.0
ECA2GM100( )
200
500
22
12.5
25
215
0.20
0.6
5.0
5.0
ECA2GM220( )
200
500
33
16
25
275
0.20
0.8
7.5
7.5
ECA2GM330( )
100
250
47
16
31.5
350
0.20
0.8
7.5
ECA2GM470
100
100
18
40
600
0.20
0.8
7.5
ECA2GM101
50
1
8
11.5
37
0.20
0.6
3.5
5.0
ECA2WM010( )
200
1000
2.2
10
12.5
44
0.20
0.6
5.0
5.0
ECA2WM2R2( )
200
500
3.3
10
16
60
0.20
0.6
5.0
5.0
ECA2WM3R3( )
200
500
4.7
10
20
79
0.20
0.6
5.0
5.0
ECA2WM4R7( )
200
500
12.5
20
130
0.20
0.6
5.0
5.0
ECA2WM100( )
200
500
7.5
ECA2WM220( )
100
250
ECA2WM330
100
10
22
16
25
210
0.20
0.8
7.5
33
16
31.5
285
0.20
0.8
7.5
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : SU (Bi-polar) Type : A
Features
● Endurance
● RoHS
: 85 °C 2000 h
compliant
Specifications
Category temperature range
–40 °C to +85 °C
Rated voltage range
6.3 V.DC to 50 V.DC
Capacitance range
2.2 µF to 6800 µF
Capacitance tolerance
±20 % (120 Hz/+20 °C)
Leakage current
I < 0.03 CV +3 (µA) After 5 minutes
Dissipation factor (tan d)
Please see the attached characteristics list
After 2000 hours application of DC working voltage (1000 hours for each polarity) at +85 °C±2 °C,
when the capacitors are restored to 20 °C, the capacitors shall meet the following limits.
Endurance
Capacitance change Within ±20 % of the initial value
tan d
< 150 % of the initial limit
DC leakage current
Shelf life
Within the initial limit
After storage for 1000 hours at +85 °C±2 °C with no voltage applied and then being stabilized
at +20 °C capacitors shall meet the limits specified in Endurance. (With voltage treatment)
Frequency correction factor for ripple current
Frequency (Hz)
50, 60
120
1k
10 k to
Correction factor
0.70
1.00
1.30
1.70
L✽
14 min.
< 08
0D±0.5
3 min.
010 <
F±0.5
Sleeve
Pressure relief
06.3 <
fd±0.05
Dimensions
0D±0.5
✽ L < 16 : L±1.0
L >20 : L±2.0
(Unit : mm)
0D
5
6.3
8
10
12.5
16
18
0d
0.5
0.5
0.6
0.6
0.6
0.8
0.8
F
2.0
2.5
3.5
5.0
5.0
7.5
7.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list (Bi-polar)
Endurance : 85 °C 2000 h (1000 hours for each polarity)
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
6.3
10
16
25
35
330
470
1000
2200
3300
4700
6800
47
100
220
330
470
1000
2200
3300
4700
10
22
33
47
220
330
470
1000
2200
3300
10
22
33
47
100
220
330
470
1000
2200
10
22
33
47
100
220
330
470
0D
L
8
10
10
12.5
16
16
18
5
6.3
8
10
10
12.5
16
16
18
5
5
5
6.3
10
10
10
12.5
16
18
5
5
6.3
6.3
8
10
12.5
12.5
16
18
5
6.3
8
8
10
12.5
12.5
12.5
11.5
12.5
20
25
25
31.5
35.5
11
11.2
11.5
16
16
20
25
31.5
35.5
11
11
11
11.2
12.5
16
20
25
31.5
35.5
11
11
11.2
11.2
11.5
16
20
20
25
35.5
11
11.2
11.5
11.5
16
20
20
25
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
250
0.30
310
0.30
430
0.30
660
0.32
760
0.34
1170
0.36
1450
0.40
90
0.25
130
0.25
200
0.25
280
0.25
340
0.25
470
0.25
690
0.27
1090
0.29
1200
0.31
40
0.20
60
0.20
80
0.20
100
0.20
260
0.20
330
0.20
380
0.20
560
0.20
750
0.22
900
0.24
45
0.15
60
0.15
90
0.15
110
0.15
180
0.15
320
0.15
350
0.15
430
0.15
680
0.15
900
0.17
43
0.15
80
0.15
100
0.15
120
0.15
230
0.15
360
0.15
450
0.15
590
0.15
Lead length (mm)
Lead space
Lead
dia.
0d
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.5
0.5
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.8
0.8
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.8
0.8
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
Min. Packaging Q'ty
Taping Taping
Straight
✽B
✽i
3.5
5.0
5.0
5.0
7.5
7.5
7.5
2.0
2.5
3.5
5.0
5.0
5.0
7.5
7.5
7.5
2.0
2.0
2.0
2.5
5.0
5.0
5.0
5.0
7.5
7.5
2.0
2.0
2.5
2.5
3.5
5.0
5.0
5.0
7.5
7.5
2.0
2.5
3.5
3.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
5.0
5.0
5.0
5.0
5.0
5.0
7.5
2.5
2.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
2.5
2.5
2.5
2.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
2.5
2.5
2.5
2.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
2.5
2.5
Part No.
ECEA0JN331U( )
ECEA0JN471X( )
ECEA0JN102U( )
ECEA0JN222U( )
ECEA0JN332U( )
ECEA0JN472U
ECEA0JN682U
ECEA1AN470U( )
ECEA1AN101X( )
ECEA1AN221U( )
ECEA1AN331U( )
ECEA1AN471U( )
ECEA1AN102X( )
ECEA1AN222U( )
ECEA1AN332U
ECEA1AN472U
ECEA1CN100U( )
ECEA1CN220U( )
ECEA1CN330U( )
ECEA1CN470U( )
ECEA1CN221X( )
ECEA1CN331U( )
ECEA1CN471U( )
ECEA1CN102U( )
ECEA1CN222U
ECEA1CN332U
ECEA1EN100U( )
ECEA1EN220X( )
ECEA1EN330U( )
ECEA1EN470U( )
ECEA1EN101U( )
ECEA1EN221U( )
ECEA1EN331U( )
ECEA1EN471U( )
ECEA1EN102U( )
ECEA1EN222U
ECEA1VN100U( )
ECEA1VN220U( )
ECEA1VN330U( )
ECEA1VN470U( )
ECEA1VN101U( )
ECEA1VN221U( )
ECEA1VN331U( )
ECEA1VN471U( )
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
100
100
50
200
200
200
200
200
200
100
100
50
200
200
200
200
200
200
200
200
100
50
200
200
200
200
200
200
200
200
100
50
200
200
200
200
200
200
200
200
1000
500
500
500
250
2000
2000
1000
500
500
500
250
2000
2000
2000
2000
500
500
500
500
2000
2000
2000
2000
1000
500
500
500
250
2000
2000
1000
1000
500
500
500
500
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list (Bi-polar)
Endurance : 85 °C 2000 h (1000 hours for each polarity)
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
0D
L
2.2
3.3
4.7
10
22
33
47
100
220
330
470
5
5
5
6.3
8
8
10
10
12.5
16
16
11
11
11
11.2
11.5
11.5
12.5
20
25
25
31.5
50
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
18
0.15
25
0.15
30
0.15
50
0.15
90
0.15
110
0.15
140
0.15
250
0.15
360
0.15
450
0.15
590
0.15
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
0d
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.8
0.8
Part No.
Taping Taping
Straight
✽B
✽i
2.0
2.0
2.0
2.5
3.5
3.5
5.0
5.0
5.0
7.5
7.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
2.5
2.5
2.5
2.5
ECEA1HN2R2U( )
ECEA1HN3R3U( )
ECEA1HN4R7U( )
ECEA1HN100U( )
ECEA1HN220U( )
ECEA1HN330U( )
ECEA1HN470U( )
ECEA1HN101U( )
ECEA1HN221U( )
ECEA1HN331U( )
ECEA1HN471U
Straight
Taping
leads
(pcs)
(pcs)
200
200
200
200
200
200
200
200
200
100
100
2000
2000
2000
2000
1000
1000
500
500
500
250
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Low Profile
Radial Lead Type
Series : KA Type : A
KA
7 mm height
↑
M
Features
● Endurance
: 85 °C 1000 h
mm height
● RoHS compliant
●7
Specifications
Category temperature range
–40 °C to +85 °C
Rated voltage range
4 V.DC to 50 V.DC
Capacitance range
2.2 µF to 470 µF
Capacitance tolerance
±20 % (120 Hz/+20 °C)
Leakage current
I < 0.01 CV or 3 (µA) After 2 minutes (Whichever is greater)
Dissipation factor (tan d)
Please see the attached characteristics list
After applying rated working voltage for 1000 hours at +85 °C±2 °C when the capacitors are
restored to 20 °C, capacitors shall meet the following limits.
Endurance
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current
Shelf life
Within the initial limit
After storage for 1000 hours at +85 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance (With voltage treatment)
Frequency correction factor for ripple current
Frequency (Hz)
50, 60
120
1k
10 k to
Correction factor
0.70
1.00
1.30
1.70
Sleeve
fd±0.05
Dimensions
+
L±1.0
14 min.
3 min.
0D±0.5
F±0.5
–
(Unit : mm)
0D
4
5
6.3
8
0d
0.45
0.45
0.45
0.45
F
1.5
2.0
2.5
2.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 85 °C 1000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
4
0.45
1.5
5.0
2.5
ECEA0GKA470( )
200
2000
7
61
0.35
0.45
2.0
5.0
2.5
ECEA0GKA101( )
200
2000
220
6.3
7
82
0.35
0.45
2.5
5.0
2.5
ECEA0GKA221( )
200
2000
2.5
ECEA0GKA331( )
200
330
8
7
110
0.35
0.45
8
7
110
0.35
0.45
8
7
140
0.35
0.45
8
7
140
0.35
0.45
2.5
5.0
2.5
ECEA0GKA331Q
2.5
5.0
ECEA0GKA471( )
1000
1000
200
ECEA0GKA471Q
1000
1000
47
4
7
46
0.24
0.45
1.5
5.0
2.5
ECEA0JKA470( )
200
2000
100
5
7
71
0.24
0.45
2.0
5.0
2.5
ECEA0JKA101( )
200
2000
220
6.3
7
103
0.24
0.45
2.5
5.0
8
7
130
0.24
0.45
2.5
100
2.5
ECEA0JKA221( )
200
2000
2.5
ECEA0JKA331( )
200
1000
8
7
130
0.24
0.45
4
7
43
0.20
0.45
1.5
5.0
2.5
ECEA1AKA330( )
200
2000
6.3
7
80
0.20
0.45
2.5
5.0
2.5
ECEA1AKA101( )
200
2000
2.5
ECEA1AKA221( )
200
8
7
120
0.20
0.45
8
7
120
0.20
0.45
5.0
ECEA0JKA331Q
2.5
5.0
1000
ECEA1AKA221Q
1000
1000
10
4
7
28
0.16
0.45
1.5
5.0
2.5
ECEA1CKA100( )
200
2000
22
4
7
39
0.16
0.45
1.5
5.0
2.5
ECEA1CKA220( )
200
2000
33
5
7
60
0.16
0.45
2.0
5.0
2.5
ECEA1CKA330( )
200
2000
47
5
7
70
0.16
0.45
2.0
5.0
2.5
ECEA1CKA470( )
200
2000
6.3
7
91
0.16
0.45
2.5
5.0
2.5
ECEA1CKA101( )
200
2000
4
7
28
0.14
0.45
1.5
5.0
2.5
ECEA1EKA100( )
200
2000
10
22
5
7
55
0.14
0.45
2.0
5.0
2.5
ECEA1EKA220( )
200
2000
33
6.3
7
65
0.14
0.45
2.5
5.0
2.5
ECEA1EKA330( )
200
2000
47
6.3
7
70
0.14
0.45
2.5
5.0
2.5
ECEA1EKA470( )
200
2000
10
5
7
30
0.12
0.45
2.0
5.0
2.5
ECEA1VKA100( )
200
2000
22
6.3
7
60
0.12
0.45
2.5
5.0
2.5
ECEA1VKA220( )
200
2000
33
6.3
7
65
0.12
0.45
2.5
5.0
2.5
ECEA1VKA330( )
200
2000
8
7
85
0.12
0.45
2.5
2.5
ECEA1VKA470( )
200
1000
8
7
85
0.12
0.45
4
7
16
0.10
0.45
2.5
ECEA1HKA2R2( )
200
2000
47
2.2
50
Straight
Taping
leads
(pcs)
(pcs)
7
100
35
Part No.
Taping Taping
Straight
✽B
✽i
5
220
25
Lead space
Lead
dia.
0d
4
33
16
Min. Packaging Q'ty
47
330
10
L
Lead length (mm)
100
470
6.3
0D
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
34
0.35
5.0
1.5
5.0
ECEA1VKA470Q
1000
3.3
4
7
18
0.10
0.45
1.5
5.0
2.5
ECEA1HKA3R3( )
200
2000
4.7
4
7
23
0.10
0.45
1.5
5.0
2.5
ECEA1HKA4R7( )
200
2000
10
5
7
35
0.10
0.45
2.0
5.0
2.5
ECEA1HKA100( )
200
2000
22
6.3
7
60
0.10
0.45
2.5
5.0
2.5
ECEA1HKA220( )
200
2000
2.5
2.5
ECEA1HKA330( )
200
33
8
7
75
0.10
0.45
8
7
75
0.10
0.45
5.0
ECEA1HKA330Q
1000
1000
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Radial Lead Type
Series : KA (Bi-polar) Type : A
Features
● Endurance
: 85 °C 1000 h
mm height
● RoHS compliant
●7
Specifications
Category temperature range
–40 °C to +85 °C
Rated voltage range
4 V.DC to 50 V.DC
Capacitance range
2.2 µF to 100 µF
Capacitance tolerance
±20 % (120 Hz/+20 °C)
Leakage current
I < 0.05 CV or 10 (µA) After 2 minutes (Whichever is greater)
Dissipation factor (tan d)
Please see the attached characteristics list
After 1000 hours application of DC working voltage (500 hours for each polarity) at +85 °C±2 °C,
when the capacitors are restored to 20 °C, the capacitors shall meet the following limits.
Endurance
Capacitance change Within ±20 % of the initial value
tan d
< 200 % of the initial limit
DC leakage current Within the initial limit
Shelf life
After storage for 1000 hours at +85 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance (With voltage treatment)
Frequency correction factor for ripple current
Frequency (Hz)
50, 60
120
1k
10 k to
Correction factor
0.70
1.00
1.30
1.70
Sleeve
L±1.0
14 min.
0D±0.5
3 min.
F±0.5
fd±0.05
Dimensions
(Unit : mm)
0D
4
5
6.3
0d
0.45
0.45
0.45
F
1.5
2.0
2.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list (Bi-polar)
Endurance : 85 °C 1000 h (500hours for each polarity)
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
4
0D
L
6.3
7
5
7
33
5
47
6.3
100
22
6.3
10
25
35
Min. Packaging Q'ty
Lead space
Lead
dia.
0d
Part No.
Taping Taping
Straight
✽B
✽i
Straight
Taping
leads
(pcs)
(pcs)
0.45
2.5
5.0
2.5
ECEA0GKN101( )
200
2000
29
0.24
0.45
2.0
5.0
2.5
ECEA0JKN220( )
200
2000
7
38
0.24
0.45
2.0
5.0
2.5
ECEA0JKN330( )
200
2000
7
46
0.24
0.45
2.5
5.0
2.5
ECEA0JKN470( )
200
2000
10
4
7
25
0.20
0.45
1.5
5.0
2.5
ECEA1AKN100( )
200
2000
5
7
35
0.20
0.45
2.0
5.0
2.5
ECEA1AKN220( )
200
2000
33
6.3
7
43
0.20
0.45
2.5
5.0
2.5
ECEA1AKN330( )
200
2000
47
6.3
7
65
0.20
0.45
2.5
5.0
2.5
ECEA1AKN470( )
200
2000
4
7
20
0.16
0.45
1.5
5.0
2.5
ECEA1CKN4R7( )
200
2000
10
5
7
25
0.16
0.45
2.0
5.0
2.5
ECEA1CKN100( )
200
2000
22
6.3
7
39
0.16
0.45
2.5
5.0
2.5
ECEA1CKN220( )
200
2000
33
6.3
7
60
0.16
0.45
2.5
5.0
2.5
ECEA1CKN330( )
200
2000
3.3
4
7
16
0.16
0.45
1.5
5.0
2.5
ECEA1EKN3R3( )
200
2000
4.7
5
7
21
0.16
0.45
2.0
5.0
2.5
ECEA1EKN4R7( )
200
2000
10
6.3
7
28
0.16
0.45
2.5
5.0
2.5
ECEA1EKN100( )
200
2000
22
6.3
7
55
0.16
0.45
2.5
5.0
2.5
ECEA1EKN220( )
200
2000
2.2
4
7
12
0.14
0.45
1.5
5.0
2.5
ECEA1VKN2R2( )
200
2000
3.3
5
7
16
0.14
0.45
2.0
5.0
2.5
ECEA1VKN3R3( )
200
2000
4.7
5
7
22
0.14
0.45
2.0
5.0
2.5
ECEA1VKN4R7( )
200
2000
6.3
7
30
0.14
0.45
2.5
5.0
2.5
ECEA1VKN100( )
200
2000
5
7
16
0.12
0.45
2.0
5.0
2.5
ECEA1HKN2R2( )
200
2000
10
2.2
50
Lead length (mm)
22
4.7
16
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
61
0.35
3.3
5
7
16
0.12
0.45
2.0
5.0
2.5
ECEA1HKN3R3( )
200
2000
4.7
6.3
7
23
0.12
0.45
2.5
5.0
2.5
ECEA1HKN4R7( )
200
2000
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, 7.5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Low Profile
Radial Lead Type
Series : KS Type : A
KS
5 mm height
↑
KA
7 mm height
↑
M
Features
● Endurance
: 85 °C 1000 h
mm height
● RoHS compliant
●5
Specifications
Category temperature range
–40 °C to +85 °C
Rated voltage range
4 V.DC to 50 V.DC
Capacitance range
2.2 µF to 330 µF
Capacitance tolerance
±20 % (120 Hz/+20 °C)
Leakage current
I < 0.01 CV or 3 (µA) After 2 minutes (Whichever is greater)
Dissipation factor (tan d)
Please see the attached characteristics list
After applying rated working voltage for 1000 hours at +85 °C±2 °C, when the capacitors are
restored to 20°C capacitors, shall meet the following limits.
Endurance
Capacitance change Within ±20 % of the initial value (4 V.DC : ±30 %)
tan d
< 200 % of the initial limit
DC leakage current
Shelf life
Within the initial limit
After storage for 1000 hours at +85 °C±2 °C with no voltage applied and then being stabilized
at +20 °C, capacitors shall meet the limits specified in Endurance (With voltage treatment)
Frequency correction factor for ripple current
Frequency (Hz)
50, 60
120
1k
10 k to
Correction factor
0.70
1.00
1.30
1.70
Sleeve
fd±0.05
Dimensions
+
L±1.0
14 min.
3 min.
0D±0.5
F±0.5
–
(Unit : mm)
0D
4
5
6.3
8
0d
0.45
0.45
0.45
0.45
F
1.5
2.0
2.5
2.5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list
Endurance : 85 °C 1000 h
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
4
6.3
4
5
47
4
5
Part No.
Taping Taping
Straight
✽B
✽i
Straight
Taping
leads
(pcs)
(pcs)
0.45
1.5
5.0
2.5
ECEA0GKS330( )
200
2000
0.45
1.5
5.0
2.5
ECEA0GKS470( )
200
2000
5
5
61
0.35
0.45
2.0
5.0
2.5
ECEA0GKS101( )
200
2000
5
82
0.35
0.45
2.5
5.0
2.5
ECEA0GKS221( )
200
2000
22
4
5
29
0.24
0.45
1.5
5.0
2.5
ECEA0JKS220( )
200
2000
33
5
5
38
0.24
0.45
2.0
5.0
2.5
ECEA0JKS330( )
200
2000
5
5
46
0.24
0.45
2.0
5.0
2.5
ECEA0JKS470( )
200
2000
6.3
5
71
0.24
0.45
2.5
5.0
2.5
ECEA0JKS101( )
200
2000
2.5
ECEA0JKS331( )
200
1000
47
100
8
5
130
0.24
0.45
8
5
130
0.24
0.45
2.5
5.0
ECEA0JKS331Q
1000
22
5
5
35
0.20
0.45
2.0
5.0
2.5
ECEA1AKS220( )
200
2000
33
5
5
43
0.20
0.45
2.0
5.0
2.5
ECEA1AKS330( )
200
2000
47
6.3
5
65
0.20
0.45
2.5
5.0
2.5
ECEA1AKS470( )
200
2000
100
6.3
5
80
0.20
0.45
2.5
5.0
2.5
ECEA1AKS101( )
200
2000
8
5
120
0.20
0.45
2.5
2.5
ECEA1AKS221( )
200
1000
8
5
120
0.20
0.45
4
5
28
0.16
0.45
200
2000
5.0
1.5
5.0
ECEA1AKS221Q
2.5
ECEA1CKS100( )
1000
22
5
5
39
0.16
0.45
2.0
5.0
2.5
ECEA1CKS220( )
200
2000
33
6.3
5
60
0.16
0.45
2.5
5.0
2.5
ECEA1CKS330( )
200
2000
47
6.3
5
70
0.16
0.45
2.5
5.0
8
5
91
0.16
0.45
2.5
8
5
91
0.16
0.45
4
5
22
0.14
0.45
4.7
2.5
ECEA1CKS470( )
200
2000
2.5
ECEA1CKS101( )
200
1000
200
2000
5.0
1.5
5.0
ECEA1CKS101Q
2.5
ECEA1EKS4R7( )
1000
10
5
5
28
0.14
0.45
2.0
5.0
2.5
ECEA1EKS100( )
200
2000
22
6.3
5
55
0.14
0.45
2.5
5.0
2.5
ECEA1EKS220( )
200
2000
33
6.3
5
65
0.14
0.45
2.5
5.0
2.5
ECEA1EKS330( )
200
2000
8
5
85
0.14
0.45
2.5
2.5
ECEA1EKS101( )
200
1000
8
5
85
0.14
0.45
4
5
16
0.12
0.45
200
2000
100
3.3
4.7
5.0
1.5
ECEA1EKS101Q
5.0
2.5
ECEA1VKS3R3( )
1000
4
5
22
0.12
0.45
1.5
5.0
2.5
ECEA1VKS4R7( )
200
2000
10
5
5
30
0.12
0.45
2.0
5.0
2.5
ECEA1VKS100( )
200
2000
22
6.3
5
60
0.12
0.45
2.5
5.0
2.5
ECEA1VKS220( )
200
2000
8
5
65
0.12
0.45
2.5
2.5
ECEA1VKS330( )
200
1000
8
5
65
0.12
0.45
33
5.0
5
85
0.12
0.45
5
85
0.12
0.45
2.2
4
5
16
0.10
0.45
1.5
5.0
2.5
ECEA1HKS2R2( )
200
2000
3.3
4
5
16
0.10
0.45
1.5
5.0
2.5
ECEA1HKS3R3( )
200
2000
4.7
22
2.5
5.0
ECEA1VKS470( )
1000
8
10
2.5
ECEA1VKS330Q
8
47
50
Lead space
Lead
dia.
0d
6.3
100
35
0.35
Min. Packaging Q'ty
100
10
25
34
Lead length (mm)
220
220
16
L
33
330
10
0D
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
26
0.35
200
ECEA1VKS470Q
1000
1000
5
5
23
0.10
0.45
2.0
5.0
2.5
ECEA1HKS4R7( )
200
2000
6.3
5
35
0.10
0.45
2.5
5.0
2.5
ECEA1HKS100( )
200
2000
2.5
ECEA1HKS220( )
200
1000
8
5
60
0.10
0.45
8
5
60
0.10
0.45
2.5
5.0
ECEA1HKS220Q
1000
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
6.3 V.DC to 50 V.DC
Aluminum Electrolytic Capacitors (Radial Lead Type)
Characteristics list (Bi-polar)
Endurance : 85 °C 1000 h (500hours for each polarity)
Case size (mm)
Rated Cap.
voltage (±20 %)
(V.DC) (µF)
6.3
10
25
L
Lead length (mm)
Min. Packaging Q'ty
Lead space
Lead
dia.
0d
Part No.
Taping Taping
Straight
✽B
✽i
Straight
Taping
leads
(pcs)
(pcs)
22
5
5
0.45
2.0
5.0
2.5
ECEA0JSN220( )
200
2000
33
6.3
5
38
0.24
0.45
2.5
5.0
2.5
ECEA0JSN330( )
200
2000
47
6.3
5
46
0.24
0.45
2.5
5.0
2.5
ECEA0JSN470( )
200
2000
10
4
5
25
0.20
0.45
1.5
5.0
2.5
ECEA1ASN100( )
200
2000
22
6.3
5
35
0.20
0.45
2.5
5.0
2.5
ECEA1ASN220( )
200
2000
33
6.3
5
43
0.20
0.45
2.5
5.0
2.5
ECEA1ASN330( )
200
2000
4
5
20
0.20
0.45
1.5
5.0
2.5
ECEA1CSN4R7( )
200
2000
4.7
16
0D
Specification
Ripple
current tan d
(120 Hz) (120 Hz)
(+85 °C) (+20 °C)
(mA r.m.s.)
29
0.24
10
5
5
25
0.20
0.45
2.0
5.0
2.5
ECEA1CSN100( )
200
2000
22
6.3
5
39
0.20
0.45
2.5
5.0
2.5
ECEA1CSN220( )
200
2000
3.3
5
5
18
0.20
0.45
2.0
5.0
2.5
ECEA1ESN3R3( )
200
2000
4.7
5
5
21
0.20
0.45
2.0
5.0
2.5
ECEA1ESN4R7( )
200
2000
6.3
5
28
0.20
0.45
2.5
5.0
2.5
ECEA1ESN100( )
200
2000
35
10
2.2
4
5
12
0.20
0.45
1.5
5.0
2.5
ECEA1VSN2R2( )
200
2000
50
2.2
5
5
16
0.20
0.45
2.0
5.0
2.5
ECEA1HSN2R2( )
200
2000
· When requesting taped product, please put the letter “B” or “i” between the “( )”. Lead wire pitch ✽B=5 mm, i=2.5 mm.
· Please refer to the page of “Taping dimensions”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Mar. 2016
CAUTION AND WARNING
1. The electronic components contained in this catalog are designed and produced for use in home electric appliances, office eq uipment, information equipment,
communications equipment, and other general purpose electronic devices.
Before use of any of these components for equipment that requires a high degree of safety, such as medical instruments, aeros pace equipment, disaster-prevention
equipment, security equipment, vehicles (automobile, train, vessel),
please be sure to contact our sales representative.
2. When applying one of these components for equipment requiring a high degree of safety, no matter what sort of application it might be, be sure to install a protective
circuit or redundancy arrangement to enhance the safety of your equipment. In addition, please carry out the safety test on your own responsibility.
3. When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on thespecifications with us in advance.
4. Technical information contained in this catalog is intended to convey examples of typical performances and/or applications a nd is not intended to make any
warranty with respect to the intellectual property rights or any other related rights of our company or any third parties nor grant any license under such rights.
5. In order to export products in this catalog, the exporter may be subject to the export license requirement under the Foreign Exchange and Foreign Trade Law of
Japan.
6. No ozone-depleting substances (ODSs) under the Montreal Protocol are used in the manufacturing processes of Automotive & Ind ustrial Systems Company, Panasonic
Corporation.
Please contact
Factory
The information in this catalog is valid as of December 2015.
Similar pages