Electric Double Layer Capacitors (Gold Capacitor)[pdf :738.36 KB]

2016
Products Catalog
Gold Capacitors
Electric Double Layer Capacitors
2016.01
http://industrial.panasonic.com/ww/products/capacitors/edlc
——— Notices ———
■ Applicable Laws and Regulations
● This product complies with the RoHS Directive (Restriction of the use of certain Hazardous substances in
electrical and electronic equipment (DIRECTIVE 2011/65/EU).
● No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in
producing this product.
● We do not PBBs or PBDEs as brominated flame retardants.
● Export procedure which followed export related regulations, such as foreign exchange and a foreign trade
method, on the occasion of export of this product Thank you for your consideration.
■ Limited applications
● This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home
appliances, computers and other office equipment, optical equipment, measuring equipment.
● High reliability and safety are required [ be / a possibility that incorrect operation of this product may do harm
to a human life or property ] more. When use is considered by the use, the delivery specifications which suited
the use separately need to be exchanged.
——— Items to be observed ———
● This specification guarantees the quality and performance of the product as individual components.
Before use, check and evaluate their compatibility with installed in your products.
● Do not use the products beyond the specifications described in this document.
■ For specifications
● Install the following systems for a failsafe design to ensure safety if these products are to be used in
equipment where a defect in these products may cause the loss of human life or other signification damage,
such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment,
electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime
prevention equipment.
· The system is equipped with a protection circuit and protection device.
· The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event of
a single fault.
■ Conditions of use
● Before using the products, carefully check the effects on their quality and performance, and determined
whether or not they can be used. These products are designed and manufactured for general-purpose and
standard use in general electronic equipment. These products are not intended for use in the following special
conditions.
(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent.
(2) In direct sunlight, outdoors, or in dust.
(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a
high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NOx.
(4) In an environment where strong static electricity or electromagnetic waves exist.
(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near
these products.
(6) Sealing or coating of these products or a printed circuit board on which these products are mounted,
with resin and other material.
(7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular,
when using water or a water-soluble cleaning agent, be careful not to leave water residues)
(8) Using in the atmosphere which strays Acid or alkaline.
(9) Using in the atmosphere which there are excessive vibration and shock.
● Please arrange circuit design for preventing impulse or transitional voltage.
Do not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage,
instantaneous high voltage, high pulse voltage etc.
● Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid
deterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and
affects performance, characteristics, and functions of customer system.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Nov. 2015
Electric Double Layer Capacitors (Gold Capacitor)
Application Guidelines (Gold Capacitor)
1. Circuit design
1.1 Product Life
The life of an electric double layer capacitor is limited. Its capacitance will decrease and its internal
resistance will increase over time.
The life of a capacitor greatly depends on the ambient temperature, humidity, applied voltage and
discharging currents. Capacitor life can be extended when these parameters are set well below the ratings.
The guaranteed durability of electric double-layer capacitors is between 1000 hours at 70 °C and 2000
hours at 85 °C. depending on product series. Generally, it is 1000 hours at 70 °C. The life of the capacitor
is guaranteed to be 16000 hours at a normal temperature (30 °C) by applying the acceleration double for
every 10 °C. Please choose the product that is suitable for the reliability that you need.
If your application incorporates this capacitor over a long period of time, then check it periodically and
replace it when necessary.
1.2 Polarity and voltage
Capacitors have polarities.
Do not apply a reverse or AC voltage. If a reversed voltage is applied to a capacitor for a long period of
time, then its life will be reduced and critical failures such as electrolyte leakage might occur.
Do not apply an over-voltage (a voltage exceeding the rated voltage).
If voltage exceeding the rating is applied to the capacitor for a long time, then its life will be reduced and critical
failures such as electrolyte leakage or physical damage due to gas generated by electrochemical reaction or
explosion might occur.
1.3 Circuits though which ripple currents pass
When using a capacitor in a circuit through which ripple currents pass, please note following matters.
(1) The internal resistance of electric double-layer capacitors is higher than that of electrolytic capacitors.
Electric double-layer capacitors may generate heat due to ripple currents.
(2) Please do not exceed the maximum operating voltage when the voltage changes from ripple.
(3) Because internal resistance is high, the gold capacitor is not basically suitable for the absorption of ripple
current.
1.4 Ambient temperature and product life
Capacitor life is affected by usage temperatures. Generally speaking, capacitor life is approximately doubled
when the temperature is decreased by 10 °C. Therefore, lower the usage temperature as much as possible.
Using capacitors beyond the guaranteed range might cause rapid deterioration of their characteristics and
cause them to break down. The temperature referred to here includes the ambient temperature within the
equipment, the heat produced by heat generating devices (power transistor, resistors, etc.), self-heating due to
ripple currents, etc. Take all of these factors into consideration when checking the capacitor’s temperature.
Do not place any heat generating devices on the back of the capacitors. Life acceleration can be
calculated with the following equation :
( T10-T )
L2 = L1×2
L1
L2
T1
T2
:
:
:
:
1
2
Life at temperature T1 °C (h)
Life at temperature T2 °C (h)
Category s upper limit temperature
Ambient temperature to calculate the life + heat generation due to ripple current (°C)
✽ Humidity also affects the capacitor’s life. When using capacitors outside the following conditions, please contact us.
A temperature at +55 °C and a relative humidity of 90 % to 95% for 500 hours.
Max. Discharging Current
Series
SG/SD/SE/NF/F
0.047 F or less
0.1 F to 0.33 F
0.47 F to 1.5 F
3.3 F to 4.7 F
10 F to 100 F
200 µA
300 µA
1 mA
—
—
RF (–40 °C, –25 °C)
—
300 µA, 3 mA
1 mA, 20 mA
—
—
RG (–40 °C, –25 °C)
—
300 µA, 1 mA
1 mA, 20 mA
—
—
1.5 Voltage drop
Pay particular attention to the instantaneous working current and the voltage drop due to the capacitor’s
internal resistance when used in backup mode. The discharging current level is different depending on the
capacitor’s internal resistance. Use a capacitor with a discharging current below what is specified by the
corresponding capacitor.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
1.6 Series connection
When connecting capacitors in series, add a bleeder resistor in parallel with each capacitor by taking the
leakage current into consideration so that the balance of voltages is not disrupted.
✽ Please present use condition about HZ/HW/HL series, and please contact us.
1.7 Electrolyte is used in the products
Electrolyte is used in the capacitors. Electrolyte leakage will damage printed circuit boards and can affect
their performance, characteristics, and functions.
1.8 External sleeve
The external sleeve is not electrical insulation, and thus capacitors should not be used in an environment
that requires electrical insulation. The sleeve is covered only for showing ratings.
2. Mounting
Solder bath temperature (°C)
2.1 Heat stress at the soldering
When soldering a capacitor to a printed circuit board, excessive heat stress could cause the deterioration
of the capacitor’s electrical characteristics. For example the integrity of the seal can be compromised
causing the electrolyte to leak, and short circuits could occur in addition to and failure of the appearance.
Please observe the following guidelines.
(1) Manual soldering
Do not touch the capacitor body with a soldering iron. Solder the capacitor using a soldering tip temperature of
350 °C or less for 4 seconds or less. Solder a the capacitor three times or less at intervals of 15 seconds or more.
(2) Flow soldering
1) Do not dip the body of the products into a
soldering bath.
General specifide ange
2) Keep the product’s surface temperature
260
at or below 100 °C for no more than 60
seconds (the peak 105 °C) when soldering.
Please refer to
the chart at right to
240
Recommended range
set soldering temperature and time. It
is recommended to check the product
temperature before you use.
220
3) The terminals of the NF/F/RF type are
designed so the bottom of the product
floats from the PWB. This is to protect
against heat stress during soldering.
0
2
4
6
8
Dipping time (s)
Do not touch the bottom of the
product directly to the PWB.
Pre-heating temperature : 110 °C or under(on the surface of circuit)
: 100 °C or under(on the surface of capacitor)
(3) Other heat stress
Pre-heating time
: 60 seconds or under
1) Keep the product’s surface temperature
Board thickness
: 0.8 mm or more
at or below 100 °C for no more than 60
seconds (the peak 105 °C) when applying
heat to bake the PWB or fixing resin, etc.The capacitor voltage must be 0.3 V or less.
2) Do not use a product more than once after it has been mounted on the PWB. Excessive heat stress is
applied when detaching it from the PWB. Please observe “(1) Manual soldering” when you adjusting it.
3) Be sure that excessive heat stress is not applied to the Gold capacitor when other parts in its
surroundings of the Gold capacitor are detached or adjusted.
(4) Others
1) The lead wires and terminals are plated for solderability. Rasping or filing lead wires or terminals
might damage the plating layer and degrade the solderability.
2) Do not apply a large mechanical force to the lead wires or terminals. Otherwise, they may break or
come off or the capacitor characteristics may be damaged.
3) There is a possibility that the sealing performance of the product is deteriorated if a coating material
that contains an organic solvent is used.
2.2 Circuit Design
Do not set wiring pattern directly under the mounted capacitor, and pass between terminals. If the
electrolyte leaks, short circuit might occur and tracking or migrations are anticipated. If a capacitor is
directly touching a PWB, then the bottom of the capacitorand the circuit pattern may short-circuit. On PWBs,
blowing flux or solder may cause the capacitor’s external sleeve to break or shrink, potentially affecting the
internal structure. In addition, please refer to application guidelines for the aluminum electrolytic capacitor.
2.3 Residual voltage
Gold Capacitors can hold a large charge and could have residual voltage. Therefore, some electronic
components with a low withstand voltage, such as semi-conductors, might be damaged.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
2.4 Circuit board cleaning
Apply the following conditions for flux cleaning after soldering. (Excepted for NF,F and RF series)
Temperature : 60 °C or less
Duraiton : 5 minutes or less
Rinse sufficiently and dry the boards.
[Recommended cleaning solvents include]
Pine Alpha ST-100s, Sunelec B-12, DK be-clear CW-5790, Aqua Cleaner 210SEP, Cold Cleaner P3-375, Cllearth-ru 750H, Clean-thru 750L, Clean-thru 710M, Techno Cleaner219, Techno Care FRW-17, Techno Care FRW-1,
Techno Care FRV1
● Consult with us if you are using a solvent other than any of those listed above or Deionized water.
● The uses of ozone depleting cleaning agents is not recommended in the interest protecting the environment.
3. Precautions for using equipment
Avoid using mounting equipment in environments where :
(1) Capacitors are exposed to water, salt water or oil.
(2) Capacitors are exposed to direct sunlight.
(3) Capacitors are exposed to high temperature and humidity where water can condense on the capacitor surface.
(4) Capacitors are subject to various active gases.
(5) Capacitors are exposed to acidic or alkaline environments.
(6) Capacitors are subject to high-frequency induction.
(7)Capacitors are subject to excessive vibrations or mechanical impact.
A brown excretion might be caused around the sealing, depending on the conditions of use. This excretion is
insulation and does not. have influence on the electrical characteristics.
4. Maintenance Precautions
Periodically check capacitors used in industrial equipment. When checking and maintaining capacitors, turn off
the equipment and discharge the capacitors beforehand. Do not apply stress to the capacitor lead terminals.
Periodically check the following items.
1) Significant appearance abnormalities (deformation, electrolyte leakage, etc.)
2) Electrical characteristics (described in the catalog or delivery specifications)
If any abnormalities are found, then replace the capacitors or take appropriate actions.
5. Emergency procedures
If the capacitors generate heat, then smoke may come out of the exterior resin. Under these conditions turn off
the equipment immediately and stop using it.
Do not place your face or hands close to the capacitor, burns might be caused.
6. Storage
Do not store capacitors in a high-temperature or high-humidity environment. Store capacitors at a room
temperature of 5 to 35 °C and a relative humidity of 85 % or less. (Recommended storage term: 1year or less.)
Store capacitors in their packaging as long as possible. Avoid storing capacitors under the following conditions.
(1) Exposed to water, high temperatures or humidity, or when condensation can occurs.
(2) Exposed to oil or in environments filled with gaseous oil contents.
(3) Exposed to salt water or environments filled with saline substances.
(4) In environments filled with harmful gases
(hydrogen disulfide, sulfurous acid, nitrous acid, chlorine, bromine, bromomethane, etc.)
(5) In environments filled with harmful alkaline gases such as ammonia.
(6) Exposed to acid or alkaline solvents.
(7) Exposed to direct sunlight, ozone, ultraviolet or radial rays.
(8) Exposed to vibration or mechanical impact.
7. Discarding
Dispose of capacitors as industrial waste. They are comprised of various metals and resin.
The precautions for the use of Electric Double Layer Capacitors (Gold Capacitors) follow the
“Precautionary guidelines for the use of fixed Electric Double Layer Capacitors for electronic equipment”,
RCR-2370C issued by EIAJ in July 2008. Please refer to the above guidelines for details.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Diagram
Stacked coin type/Standard
Miniaturized
SD
Taped
5.5 V.DC
0.22 F to 0.33 F
–40, –25 °C to +70 °C
NF
5.5 V.DC
0.22 F to 1.5 F
–40, –25 °C to +70 °C
SE
5.5 V.DC
0.22 F
–40, –25 °C to +70 °C
SG
5.5 V.DC
0.47 F to 1.5 F
–40, –25 °C to +70 °C
Standard
Stacked coin type/High reliability
RG
3.6 V.DC
0.22 F to 1.5 F
–40, –25 °C to +85 °C
F
5.5 V.DC
0.1 F to 1.0 F
–40, –25 °C to +85 °C
RF
85 °C
2000 h
guaranteed
5.5 V.DC
0.1 F to 1.0 F
–40, –25 °C to +85 °C
85 °C 1000 h
guaranteed
Radial lead type
HW
HZ
2.3(2.1) V.DC
22 F to 70 F
< 0.1 Ω
–25 °C ~ +70(60) °C
2.5 V.DC
3.3 F to 10 F
–25 °C to +70 °C
NEW
Miniaturized/
High withstand voltage
HL
2.7 V.DC
50 F to 100 F
< 0.01 Ω
–40 °C to +65 °C
Low resistance/High reliability (2000 h)
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
RG Low temperature assured product
Series :
Features
● Endurance
: +85 °C 2000 h
temperature range : –40 °C to +85 °C
● RoHS compliant
● Category
Recommended applications
● Backup
of data/RTC of base station, electronic meter, and industrial equipment
Specifications
Category temp. range
Maximum operating voltage
Nominal capacitance
Characteristics at
low temperature
Endurance
Shelf life
–40 °C to +85 °C
3.6 V.DC
0.22 F
1.0 F, 1.5 F
Capacitance change ±30 % of initial measured value at +20 °C (at –40 °C)
Internal resistance < 7 times of initial measured value at +20 °C (at –40 °C)
After 2000 hours application of maximum operating voltage at +85 °C
Capacitance change ±30 % of initial measured value at 20 °C
100 Ω or less (0.22 F)
Internal resistance
40 Ω or less (1.0 F, 1.5 F)
After 2000 hours storage at +85 °C without load (voltage)
Capacitance change Capacitance change shall meet the specified limits for Endurance
Internal resistance Internal resistance shall meet the specified limits for Endurance
Dimensions in mm(not to scale)
RG series 0.22(F)
Terminal : V
11.5 max.
6.0 max.
3.0±0.5
0.2±0.05
5.0±0.8
1.0±0.1
–
5.0±0.5
0.2±0.05
3.0±0.5
20.0±0.5
0.8±0.05
(1.7)
f19.0±0.3
20.5 Max.
+
0.20±0.05
0.2±0.05
10.0±0.5
Sleeve
5.5±0.5
21.0 max.
4.0±0.3
11.5 max.
010.5 max.
f19.0±0.3
Terminal : H
3.5±0.3 6.5 max.
Sleeve
5.0 max.
10.5 max.
0.8±0.05
(1.7)
Terminal : H
5.0±0.3
Terminal : V
RG series 1.0, 1.5(F)
1.0±0.1
(Unit : mm)
Characteristics list
Maximum
operating
voltage
(V.DC)
3.6
0.22
0.176 to 0.396
< 50
300 µA or less
EECRG0V224( )N
1.0
Min.
packaging
q'ty
(pcs)
200
1.0
0.8 to 1.8
< 20
1 mA or less
EECRG0V105( )N
4.1
100
1.5
1.2 to 2.7
< 20
1 mA or less
EECRG0V155( )N
4.2
100
Capacitance
(F)
Capacitance Internal resistance Recommended
tolerance (Initial specified value) discharge current
(F)
(Ω) at 1 kHz
(mA)
Parts number
Mass
(Reference value)
(g)
Do not use reflow soldering. (IR, Atmospherheating methods, etc.) Please refer to the page of “Application guidelines”.
( ) : Please use V or H to indicate terminal type.
The recommended discharge current is a reference value. Please design your equipment(circuit) in consideration of IR dorop.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
RG
Features
● Endurance
: +85 °C 2000 h
be discharged mA current
● RoHS compliant
● Can
Recommended applications
● Backup
● For
of data/RTC of base station, electronic meter, and industrial equipment
assist of rapid load change
Specifications
Category temp. range
Maximum operating voltage
Nominal capacitance
Characteristics at
low temperature
Endurance
Shelf life
–25 °C to +85 °C
3.6 V.DC
0.22 F
1.0 F, 1.5 F
Capacitance change ±30 % of initial measured value at +20 °C (at –25 °C)
Internal resistance < 5 times of initial measured value at +20 °C (at –25 °C)
After 2000 hours application of maximum operating voltage at +85 °C
Capacitance change ±30 % of initial measured value at 20 °C
100 Ω or less (0.22 F)
Internal resistance
40 Ω or less (1.0 F, 1.5 F)
After 2000 hours storage at +85 °C without load (voltage)
Capacitance change Capacitance change shall meet the specified limits for Endurance
Internal resistance Internal resistance shall meet the specified limits for Endurance
Dimensions in mm(not to scale)
RG series 0.22(F)
Terminal : V
11.5 max.
6.0 max.
3.0±0.5
0.2±0.05
5.0±0.8
1.0±0.1
–
5.0±0.5
1.0±0.1
0.2±0.05
3.0±0.5
20.0±0.5
0.8±0.05
(1.7)
f19.0±0.3
20.5 Max.
+
0.20±0.05
0.2±0.05
10.0±0.5
Sleeve
5.5±0.5
21.0 max.
4.0±0.3
11.5 max.
010.5 max.
f19.0±0.3
Terminal : H
3.5±0.3 6.5 max.
Sleeve
5.0 max.
10.5 max.
0.8±0.05
(1.7)
Terminal : H
5.0±0.3
Terminal : V
RG series 1.0, 1.5(F)
(Unit : mm)
Characteristics list
Maximum
operating
voltage
(V.DC)
3.6
0.22
0.176 to 0.396
< 50
1 or less
EECRG0V224( )
1.0
Min.
packaging
q'ty
(pcs)
200
1.0
0.8 to 1.8
< 20
20 or less
EECRG0V105( )
4.1
100
1.5
1.2 to 2.7
< 20
20 or less
EECRG0V155( )
4.2
100
Capacitance
(F)
Capacitance Internal resistance Recommended
tolerance (Initial specified value) discharge current
(F)
(Ω) at 1 kHz
(mA)
Parts number
Mass
(Reference value)
(g)
Do not use reflow soldering. (IR, Atmospherheating methods, etc.) Please refer to the page of “Application guidelines”.
( ) : Please use V or H to indicate terminal type.
The recommended discharge current is a reference value. Please design your equipment(circuit) in consideration of IR dorop.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
RF Low temperature assured product
Series :
Features
● Endurance
: +85 °C 2000 h
temperature range : –40 °C to +85 °C
● RoHS compliant
● Category
Recommended applications
● Backup
of data/RTC of base station, electronic meter, and industrial equipment
Specifications
Category temp. range
Maximum operating voltage
Nominal capacitance
Characteristics at
low temperature
Endurance
Shelf life
–40 °C to +85 °C
5.5 V.DC
0.1 F
0.68 F, 1.0 F
Capacitance change ±30 % of initial measured value at +20 °C (at –40 °C)
Internal resistance < 7 times of initial measured value at +20 °C (at –40 °C)
After 2000 hours application of maximum operating voltage at +85 °C
Capacitance change ±30 % of initial measured value at 20 °C
150 Ω or less (0.1 F)
Internal resistance
40 Ω or less (0.68 F, 1.0 F)
After 2000 hours storage at +85 °C without load (voltage)
Capacitance change Capacitance change shall meet the specified limits for Endurance
Internal resistance Internal resistance shall meet the specified limits for Endurance
Dimensions in mm(not to scale)
0.8±0.1
–
9.5 max. 6±1
+
6±1
3.5±0.5
2.5±0.5
0.5±0.1
+
fD
–
Sleeve
5.0
5.0±0.3
1.2±0.1
Cap (F)
0D (mm)
0.1
13.5 max
0.68, 1.0
21.5 max
01.1±0.05
(Recommended)
(Unit : mm)
Characteristics list
Maximum
operating
voltage
(V.DC)
5.5
0.1
0.080 to 0.180
< 75
300 µA or less
EECRF0H104N
3.3
Min.
packaging
q'ty
(pcs)
200
0.68
0.544 to 1.224
< 20
1 mA or less
EECRF0H684N
10.0
100
1.0
0.8 to 1.8
< 20
1 mA or less
EECRF0H105N
10.0
100
Capacitance
(F)
Capacitance Internal resistance
Recommended
tolerance (Initial specified value)
discharge current
(F)
(Ω) at 1 kHz
Parts number
Mass
(Reference value)
(g)
Do not use reflow soldering. (IR, Atmospherheating methods, etc.) Please refer to the page of “Application guidelines”.
The recommended discharge current is a reference value. Please design your equipment(circuit) in consideration of IR dorop.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
RF
Features
● Endurance
: +85 °C 2000 h
be discharged mA current
● RoHS compliant
● Can
Recommended applications
● Backup
● For
of data/RTC of base station, electronic meter, and industrial equipment
assist of rapid load change
Specifications
Category temp. range
Maximum operating voltage
Nominal capacitance
Characteristics at
low temperature
Endurance
Shelf life
–25 °C to +85 °C
5.5 V.DC
0.1 F
0.68 F, 1.0 F
Capacitance change ±30 % of initial measured value at +20 °C (at –25 °C)
Internal resistance < 5 times of initial measured value at +20 °C (at –25 °C)
After 2000 hours application of maximum operating voltage at +85 °C
Capacitance change ±30 % of initial measured value at 20 °C
150 Ω or less (0.1 F)
Internal resistance
40 Ω or less (0.68 F, 1.0 F)
After 2000 hours storage at +85 °C without load (voltage)
Capacitance change Capacitance change shall meet the specified limits for Endurance
Internal resistance Internal resistance shall meet the specified limits for Endurance
Dimensions in mm(not to scale)
5.0±0.3
1.2±0.1
0.8±0.1
–
9.5 max. 6±1
+
Cap (F)
5.0
6±1
3.5±0.5
2.5±0.5
0.5±0.1
+
fD
–
Sleeve
0D (mm)
0.1
13.5 max
0.68, 1.0
21.5 max
01.1±0.05
(Recommended)
(Unit : mm)
Characteristics list
Maximum
operating
voltage
(V.DC)
Capacitance
(F)
0.1
0.080 to 0.180
< 75
3 or less
EECRF0H104
3.3
Min.
packaging
q'ty
(pcs)
200
5.5
0.68
0.544 to 1.224
< 20
20 or less
EECRF0H684
10.0
100
1.0
0.8 to 1.8
< 20
20 or less
EECRF0H105
10.0
100
Capacitance Internal resistance Recommended
tolerance (Initial specified value) discharge current
(F)
(Ω) at 1 kHz
(mA)
Parts number
Mass
(Reference value)
(g)
Do not use reflow soldering. (IR, Atmospherheating methods, etc.) Please refer to the page of “Application guidelines”.
The recommended discharge current is a reference value. Please design your equipment(circuit) in consideration of IR dorop.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
SD Low temperature assured product
Features
● Endurance
: +70 °C 1000 h
temperature range : –40 °C to +70 °C
● RoHS compliant
● Category
Recommended applications
● Memory
back-up for video and audio equipment, cameras, telephones, printers, data terminals,
rice cookers, intelligent remote controls
Specifications
Category temp. range
Maximum operating voltage
Nominal cap.range
Characteristics at
low temperature
Endurance
Shelf life
–40 °C to +70 °C
5.5 V.DC
0.22 F, 0.33 F
Capacitance change ±30 % of initial measured value at +20 °C (at –40 °C)
Internal resistance < 7 times of initial measured value at +20 °C (at –40 °C)
After 1000 hours application of 5.5 V.DC at +70 °C, the capacitor shall meet the following limits.
Capacitance change ±30 % of initial measured value
Internal resistance < 4 times of initial specified value
After 1000 hours storage at +70 °C without load, the capacitor shall meet the specified
limits for Endurance.
Dimensions in mm(not to scale)
Terminal: V
Terminal: H
f10.5 max.
Sleeve
B max.
11.5 max.
10.5 max.
0.8±0.05
(1.7)
3.0±0.5
0.2±0.05
5.0±0.8
0.2±0.05
+
10.0±0.5
–
(Unit : mm)
Cap. (F)
0.22
0.33
B
5.0
5.5
Cap. (F)
0.22
0.33
3.0±0.5
A max.
11.5 max.
0.8±0.05
(1.7)
(Unit : mm)
A
6.0
6.5
Characteristics list
Maximum
operating Capacitance
(F)
voltage
(V.DC)
0.22
5.5
0.33
0.176 to 0.396
< 75
300 or less
Min.
Mass
packaging
Parts number
(Reference value)
q'ty
(g)
(pcs)
EECS0HD224( )N
1.0
200
0.264 to 0.594
< 75
300 or less
EECS0HD334( )N
Capacitance
tolerance
(F)
Internal resistance Recommended
(Initial specified value) discharge current
(Ω) at 1 kHz
(µA)
1.1
200
( ) Please use V or H, to indicate the terminal style.
Note : Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
SD
Features
● Endurance
● RoHS
: +70 °C 1000 h
compliant
Recommended applications
● Memory
back-up for video and audio equipment, cameras, telephones, printers, data terminals,
rice cookers, intelligent remote controls
Specifications
Category temp. range
–25 °C to +70 °C
Maximum operating voltage
5.5 V.DC
Nominal cap.range
0.22 F, 0.33 F
Capacitance change ±30 % of initial measured value at +20 °C (at –25 °C)
Characteristics at
low temperature
Internal resistance
< 5 times of initial measured value at +20 °C (at –25 °C)
After 1000 hours application of 5.5 V.DC at +70 °C, the capacitor shall meet the following limits.
Endurance
Capacitance change ±30 % of initial measured value
Internal resistance < 4 times of initial specified value
After 1000 hours storage at +70 °C without load, the capacitor shall meet the specified
limits for Endurance.
Shelf life
Dimensions in mm(not to scale)
Terminal : V
Terminal : H
f10.5 max.
Sleeve
B max.
11.5 max.
10.5 max.
0.8±0.05
(1.7)
3.0±0.5
0.2±0.05
5.0±0.8
0.2±0.05
+
10.0±0.5
–
(Unit : mm)
Cap. (F)
0.22
0.33
B
5.0
5.5
Cap. (F)
0.22
0.33
3.0±0.5
A max.
11.5 max.
0.8±0.05
(1.7)
(Unit : mm)
A
6.0
6.5
Characteristics list
Maximum
operating Capacitance
voltage
(F)
(V.DC)
0.22
5.5
0.33
0.176 to 0.396
< 75
300 or less
Min.
Mass
packaging
(Reference value)
Parts number
q'ty
(g)
(pcs)
EECS0HD224( )
1.0
200
0.264 to 0.594
< 75
300 or less
EECS0HD334( )
Capacitance
tolerance
(F)
Internal resistance Recommended
(Initial specified value) discharge current
(Ω) at 1 kHz
(µA)
1.1
200
( ) Please use V or H, to indicate the terminal style.
Note : Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
SG Low temperature assured product
Features
● Endurance
: +70 °C 1000 h
temperature range : –40 °C to +70 °C
● Maximum height of 6.5 mm (H Terminal)
● RoHS compliant
● Category
Recommended applications
● Memory
back-up for video and audio equipment, cameras, telephones, printers, data terminals,
rice cookers and intelligent remote controls
Specifications
Category temp. range
–40 °C to +70 °C
Maximum operating voltage
5.5 V.DC
Nominal cap.range
0.47 F to 1.5 F
Capacitance change ±30 % of initial measured value at +20 °C (at –40 °C)
Characteristics at
low temperature
Internal resistance
< 7 times of initial measured value at +20 °C (at –40 °C)
After 1000 hours application of 5.5 V.DC at +70 °C, the capacitor shall meet the following limits.
Endurance
Capacitance change ±30 % of initial measured value
Internal resistance < 4 times of initial specified value
After 1000 hours storage at +70 °C without load, the capacitor shall meet the specified
limits for Endurance.
Shelf life
Dimensions in mm(not to scale)
Terminal: V
Terminal: H
Sleeve
f19.0±0.3
5.0±0.3
–
20.5 max.
f19.0±0.3
3.5±0.3 6.5 max.
1.0±0.1
4.0±0.3
21.0 max.
5.5±0.5
+
5.0±0.5 0.20±0.05
20.0±0.5
(Unit : mm)
0.2±0.05
1.0±0.1
(Unit : mm)
Characteristics list
Maximum
operating Capacitance
voltage
(F)
(V.DC)
0.47
5.5
1.0
1.5
Capacitance
tolerance
(F)
0.376 to 1.41
0.80 to 1.80
1.20 to 2.70
Internal resistance Recommended
(Initial specified value) discharge current
(Ω) at 1kHz
(mA)
< 30
< 30
< 30
1 or less
1 or less
1 or less
Min.
Mass
packaging
(Reference value)
Part number
q’ty
(g)
(pcs)
EECS5R5( )474N
4.1
100
EECS5R5( )105N
4.1
100
EECS5R5( )155N
4.2
100
( ) Please use V or H, to indicate the terminal style.
Note : Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
SG
Features
● Endurance
: +70 °C 1000 h
height of 6.5 mm (H Terminal)
● RoHS compliant
● Maximum
Recommended applications
● Memory
back-up for video and audio equipment, cameras, telephones, printers, data terminals,
rice cookers and intelligent remote controls
Specifications
Category temp. range
Maximum operating voltage
Nominal cap.range
Characteristics at
low temperature
Endurance
Shelf life
–25 °C to +70 °C
5.5 V.DC
0.47 F to 1.5 F
Capacitance change ±30 % of initial measured value at +20 °C (at –25 °C)
Internal resistance < 5 times of initial measured value at +20 °C (at –25 °C)
After 1000 hours application of 5.5 V.DC at +70 °C, the capacitor shall meet the following limits.
Capacitance change ±30 % of initial measured value
Internal resistance < 4 times of initial specified value
After 1000 hours storage at +70 °C without load, the capacitor shall meet the specified
limits for Endurance.
Dimensions in mm(not to scale)
Terminal: V
Terminal: H
Sleeve
f19.0±0.3
5.0±0.3
–
f19.0±0.3
20.5 max.
3.5±0.3 6.5 max.
1.0±0.1
4.0±0.3
21.0 max.
5.5±0.5
+
5.0±0.5 0.20±0.05
20.0±0.5
0.2±0.05
(Unit : mm)
1.0±0.1
(Unit : mm)
Characteristics list
Maximum
Capacitance
operating Capacitance
tolerance
voltage
(F)
(F)
(V.DC)
0.47
0.376 to 1.41
5.5
1.0
0.80 to 1.80
1.5
1.20 to 2.70
Internal resistance Recommended
(Initial specified value) discharge current
(Ω) at 1kHz
(mA)
< 30
< 30
< 30
1 or less
1 or less
1 or less
Part number
EECS5R5( )474
EECS5R5( )105
EECS5R5( )155
Min.
Mass
packaging
(Reference value)
q’ty
(g)
(pcs)
4.1
100
4.1
100
4.2
100
( ) Please use V or H, to indicate the terminal style.
Note : Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
SE Low temperature assured product
Features
● Endurance
: +70 °C 1000 h
temperature range : –40 °C to +70 °C
● Automatic insertion available
● RoHS compliant
● Category
Recommended applications
● Memory
back-up for video and audio equipment, cameras, telephones, printers, data terminals,
rice cookers and intelligent remote controls.
Specifications
Category temp. range
–40 °C to +70 °C
Maximum operating voltage
5.5 V.DC
Nominal cap.range
0.22 F
Capacitance change ±30 % of initial measured value at +20 °C (at –40 °C)
Characteristics at
low temperature
Internal resistance
< 7 times of initial measured value at +20 °C (at –40 °C)
After 1000 hours application of 5.5 V.DC at +70 °C, the capacitor shall meet the following limits.
Endurance
Capacitance change ±30 % of initial measured value
Internal resistance < 4 times of initial specified value
After 1000 hours storage at +70 °C without load, the capacitor shall meet the specified
limits for Endurance.
Shelf life
Dimensions in mm(not to scale)
5.4±0.8
△h
△h1
10.5 max.
P
–
+
fd
+
W
W1
W0
H0
P1 F
–
W2
13.4 max.
H1
P2
P0
fD0
(Unit : mm)
Dimensions
Nominal
Tolerance
0d
P0
F
W
W0
W1
W2
H0
0D0
P
P1
P2
△h, △h1
H1
0.55
12.7
5.0
18.0
5.5 <
9.0
0 to 3.0
16.4
4.0
12.7
3.85
6.35
0
30.3 >
±0.05
±0.2
+0.8
–0.2
±0.5
–
±0.5
–
±0.5
±0.2
±1.0
±0.50
±1.00
±1.0
–
Characteristics list
Maximum
operating Capacitance
voltage
(F)
(V.DC)
0.22
5.5
Capacitance
tolerance
(F)
0.176 to 0.396
Internal resistance Recommended
(Initial specified value) discharge current
(Ω) at 1kHz
(µA)
< 75
300 or less
Part number
EECSE0H224N
Min.
Mass
packaging
(Reference value)
q’ty
(g)
(pcs)
1.0
1000
Note: 1. When ordering please observe the minimum packaging quantity.
2. When the surface mount component goes through UV or a heat oven to affix the adhesive glue, the capacitor’s surface
temperature should not exceed 100 °C for more than 60 seconds (maximum temperature should not exceed 105 °C)
3. Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
SE
Features
● Endurance
: +70 °C 1000 h
insertion available
● RoHS compliant
● Automatic
Recommended applications
● Memory
back-up for video and audio equipment,cameras, telephones, printers, data terminals,
rice cookers and intelligent remote controls.
Specifications
Category temp. range
–25 °C to +70 °C
Maximum operating voltage
5.5 V.DC
Nominal cap.range
0.22 F
Capacitance change ±30 % of initial measured value at +20 °C (at –25 °C)
Characteristics at
low temperature
Internal resistance
< 5 times of initial measured value at +20 °C (at –25 °C)
After 1000 hours application of 5.5 V.DC at +70 °C, the capacitor shall meet the following limits.
Endurance
Capacitance change ±30 % of initial measured value
Internal resistance
< 4 times of initial specified value
After 1000 hours storage at +70 °C without load, the capacitor shall meet the specified
limits for Endurance.
Shelf life
Dimensions in mm(not to scale)
5.4±0.8
△h
△h1
10.5 max.
P
–
+
fd
–
+
W
W1
W0
H0
P1 F
W2
13.4 max.
H1
P2
P0
fD0
(Unit : mm)
Dimensions
Nominal
Tolerance
0d
P0
F
W
W0
W1
W2
H0
0D0
P
P1
P2
△h, △h1
H1
0.55
12.7
5.0
18.0
5.5 <
9.0
0 to 3.0
16.4
4.0
12.7
3.85
6.35
0
30.3 >
±0.05
±0.2
+0.8
–0.2
±0.5
–
±0.5
–
±0.5
±0.2
±1.0
±0.50
±1.00
±1.0
–
Characteristics list
Maximum
operating Capacitance
voltage
(F)
(V.DC)
0.22
5.5
Capacitance
tolerance
(F)
0.176 to 0.396
Internal resistance Recommended
(Initial specified value) discharge current
(Ω) at 1kHz
(µA)
< 75
300 or less
Part number
EECSE0H224
Min.
Mass
packaging
(Reference value)
q’ty
(g)
(pcs)
1.0
1000
Note: 1. When ordering please observe the minimum packaging quantity.
2. When the surface mount component goes through UV or a heat oven to affix the adhesive glue, the capacitor’s surface
temperature should not exceed 100 °C for more than 60 seconds (maximum temperature should not exceed 105 °C)
3. Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
05
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
NF Low temperature assured product
Features
● Endurance
: +70 °C 1000 h
temperature range : –40 °C to +70 °C
● RoHS compliant
● Category
Recommended applications
● Memory
back-up for video and audio equipment, cameras, telephones, printers, data terminals,
rice cookers and intelligent remote controls.
Specifications
Category temp. range
–40 °C to +70 °C
Maximum operating voltage
5.5 V.DC
Nominal cap.range
0.22 F to 1.5 F
Capacitance change ±30 % of initial measured value at +20 °C (at –40 °C)
Characteristics at
low temperature
Internal resistance
< 7 times of initial measured value at +20 °C (at –40 °C)
After 1000 hours application of 5.5 V.DC at +70 °C, the capacitor shall meet the following limits.
Endurance
Capacitance change ±30 % of initial measured value
Internal resistance < 4 times of initial specified value
After 1000 hours storage at +70 °C without load, the capacitor shall meet the specified
limits for Endurance.
Shelf life
Dimensions in mm(not to scale)
1.2±0.1
5.0±0.3
–
0.5±0.1
0.8±0.1
+
L max.
6±1
5.0
6±1
3.5±0.5
2.5±0.5
+
0D max.
–
Sleeve
(Unit : mm)
Size
D
L
13.5
7.5
21.5
8.0
Case
code
A
B
01.1±0.05
(Recommended)
Characteristics list
Maximum
operating
voltage
(V.DC)
5.5
0.22
0.176 to 0.396
< 75
Min.
Mass
Case
packaging
Parts number
(Reference value)
code
q’ty
(g)
(pcs)
300 µA or less EECF5R5U224N
A
2.6
200
0.47
0.376 to 1.41
< 30
1 mA or less
1.0
0.80
to 1.80
< 30
1 mA or less
EECF5R5U105N
1.5
1.20
to 2.70
< 30
1 mA or less
EECF5R5U155N
Capacitance
(F)
Capacitance
tolerance
(F)
Internal resistance
Recommended
(Initial specified value)
discharge current
(Ω) at 1 kHz
EECF5R5U474N
B
7.9
100
B
8.1
100
B
8.1
100
Note : Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
NF
Features
● Endurance
● RoHS
: +70 °C 1000 h
compliant
Recommended applications
● Memory
back-up for video and audio equipment, cameras, telephones, printers, data terminals,
rice cookers and intelligent remote controls.
Specifications
Category temp. range
–25 °C to +70 °C
Maximum operating voltage
5.5 V.DC
Nominal cap.range
0.22 F to 1.5 F
Capacitance change ±30 % of initial measured value at +20 °C (at –25 °C)
Characteristics at
low temperature
Internal resistance
< 5 times of initial measured value at +20 °C (at –25 °C)
After 1000 hours application of 5.5 V.DC at +70 °C, the capacitor shall meet the following limits.
Endurance
Capacitance change ±30 % of initial measured value
Internal resistance
< 4 times of initial specified value
After 1000 hours storage at +70 °C without load, the capacitor shall meet the specified
limits for Endurance.
Shelf life
Dimensions in mm(not to scale)
(Unit : mm)
1.2±0.1
5.0±0.3
–
0.5±0.1
6±1
+
D
13.5
21.5
A
B
L
7.5
8.0
5.0
6±1
3.5±0.5
2.5±0.5
0D max.
+
L max.
Size
Case
code
0.8±0.1
–
Sleeve
01.1±0.05
(Recommended)
Characteristics list
Maximum
operating
voltage
(V.DC)
5.5
Capacitance
(F)
Capacitance
tolerance
(F)
Internal resistance
Recommended
(Initial specified value)
discharge current
(Ω) at 1 kHz
Parts number
Min.
Mass
Case
packaging
(Reference value)
code
q’ty
(g)
(pcs)
A
2.6
200
0.22
0.176 to 0.396
< 75
300 µA or less
EECF5R5U224
0.47
0.376 to 1.41
< 30
1 mA or less
EECF5R5U474
1.0
0.80
to 1.80
< 30
1 mA or less
EECF5R5U105
B
8.1
100
1.5
1.20
to 2.70
< 30
1 mA or less
EECF5R5U155
B
8.1
100
B
7.9
100
Note : Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
04
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
F Low temperature assured product
Features
● Endurance
: +85 °C 1000 h
temperature range : –40 °C to +85 °C
● RoHS compliant
● Category
Recommended Applications
● Backup
of data/RTC of base station,electronic meter, and industrial equipment
Specifications
Category temp. range
–40 °C to +85 °C
Maximum operating voltage
5.5 V.DC
Nominal cap.range
0.1 F to 1.0 F
Capacitance change ±30 % of initial measured value at +20 °C (at –40 °C)
Characteristics at
low temperature
< 7 times of initial measured value at +20 °C (at –40 °C)
Internal resistance
After 1000 hours application of 5.5 V.DC at +85 °C, the capacitor shall meet the following limits.
Endurance
Capacitance change ±30 % of initial measured value
Internal resistance < 4 times of initial specified value
After 1000 hours storage at +85 °C without load, the capacitor shall meet the specified
limits for Endurance.
Shelf Life
Dimensions in mm(not to scale)
1.2±0.1
5.0±0.3
0.8±0.1
A
B
–
L max.
6±1
5.0
6±1
3.5±0.5
2.5±0.5
0.5±0.1
+
0D max.
–
Sleeve
(Unit : mm)
Size
D
L
13.5
9.5
21.5
9.5
Case
code
+
01.1±0.05
(Recommended)
Characteristics list
Maximum
operating
voltage
(V.DC)
5.5
Internal resistance
Recommended
(Initial specified value)
discharge current
(Ω)at 1 kHz
Min.
Mass
Case
packaging
(Reference value)
code
q’ty
(g)
(pcs)
A
3.3
200
Capacitance
(F)
Capacitance
tolerance
(F)
0.10
0.080 to 0.180
< 100
300 µA or less EECF5R5H104N
0.47
0.376 to 0.846
< 75
1 mA or less EECF5R5H474N
B
10.0
100
0.68
0.544 to 1.224
< 50
1 mA or less EECF5R5H684N
B
10.0
100
1.00
0.80
< 50
1 mA or less EECF5R5H105N
B
10.0
100
to 1.80
Parts number
Note : Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Stacked Coin Type
Series :
F
Features
● Endurance
● RoHS
: +85 °C 1000 h
compliant
Recommended Applications
● Backup
of data/RTC of base station, electronic meter, and industrial equipmet
Specifications
Category temp. range
–25 °C to +85 °C
Maximum operating voltage
5.5 V.DC
Nominal cap.range
0.1 F to 1.0 F
Capacitance change ±30 % of initial measured value at +20 °C (at –25 °C)
Characteristics at
low temperature
Internal resistance
< 5 times of initial measured value at +20 °C (at –25 °C)
After 1000 hours application of 5.5 V.DC at +85 °C, the capacitor shall meet the following limits.
Endurance
Capacitance change ±30 % of initial measured value
Internal resistance
< 4 times of initial specified value
After 1000 hours storage at +85 °C without load, the capacitor shall meet the specified
limits for Endurance.
Shelf Life
Dimensions in mm(not to scale)
(Unit : mm)
1.2±0.1
5.0±0.3
D
13.5
21.5
A
B
–
L
9.5
9.5
L max.
6±1
5.0
6±1
3.5±0.5
2.5±0.5
0.5±0.1
+
0D max.
–
Sleeve
Size
Case
code
0.8±0.1
+
01.1±0.05
(Recommended)
Characteristics list
Maximum
operating
voltage
(V.DC)
5.5
Internal resistance
Recommended
(Initial specified value)
discharge current
(Ω) at 1 kHz
Capacitance
(F)
Capacitance
tolerance
(F)
0.10
0.080 to 0.180
< 100
Parts number
300 µA or less EECF5R5H104
Min.
Mass
Case
packaging
(Reference value)
code
q’ty
(g)
(pcs)
A
3.3
200
0.47
0.376 to 0.846
< 75
1 mA or less
EECF5R5H474
B
10.0
100
0.68
0.544 to 1.224
< 50
1 mA or less
EECF5R5H684
B
10.0
100
1.00
0.80
< 50
1 mA or less
EECF5R5H105
B
10.0
100
to 1.80
Note : Do not use reflow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Radial lead Type
Series :
HZ
Features
● Miniaturized,
High withstand voltage
be discharge mA or more current
● RoHS compliant
● Can
Recommended Applications
● Solar
battery operated circuits
Power Supplies (UPS)
● Back-up
Specifications
Category temp. range
Maximum operating voltage
Nominal cap. range
Characteristics at
low temperature
Endurance
Shelf Life
–25 °C to +70 °C
2.5 V.DC
3.3 F
4.7 F
10 F
Capacitance change ±30 % of initial measured value at 20 °C (at –25 °C)
Internal resistance
< 4 times of initial specified value. (at –25 °C)
After 1000 hours application of 2.5 V.DC at +70 °C
Capacitance change ±30 % of initial measured value at 20 °C
Internal resistance
< 4 times of initial specified value.
After 1000 hours storage at +70 °C without load (voltage)
Capacitance change ±30 % of initial measured value at 20 °C
Internal resistance
< 4 times of initial specified value.
Dimensions in mm(not to scale)
Sleeve
0d±0.05
(Unit : mm)
P±0.5
(>8.0 mm dia.)
Vent
L+2 max.
0D+0.5 max.
3 min.
14 min.
Capacitance
0D
(F)
3.3
8.0
4.7
10
10
10
L
0d
P
20
20
30
0.6
0.6
0.6
3.5
5.0
5.0
Characteristics list
Min.
Category Maximum
Internal
Recommended
Mass
Capacitance
operating Capacitance
packaging
temp.
resistance
discharge
Parts number (Reference value)
tolerance
voltage
q’ty
range
(F)
(Initial specified value)
current
(F)
(g)
(V.DC)
(pcs)
(°C)
(Ω) at 1 kHz
3.3
2.64 to 4.62
300 mA or less EECHZ0E335
1.5
200
< 0.3
–25 to +70
2.5
4.7
3.76 to
10
8
6.58
to 14
< 0.3
300 mA or less EECHZ0E475
< 0.2
1 A or less
EECHZ0E106
2.1
200
3.1
200
Note : Do not use reflow soldering. (IR, Atmosphere heating methods, etc. )
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Jan. 2016
Electric Double Layer Capacitors (Gold Capacitor)
Radial lead Type
Series :
HW
Features
● Guaranteed
at 70 °C (60°C 1000 h)
be discharge mA or more current
● RoHS compliant
● Can
Recommended Applications
● Solar
battery operated circuits (Road guidance flasher), Quick charging motor drives (Toy car)
Power Supplies (UPS)
● Back-up
Specifications
Category temp. range
Maximum operating voltage
Nominal cap. range
Characteristics at
low Temperature
–25 °C to +70 °C
–25 °C to +60 °C
2.3 V.DC
2.3 V.DC
2.1 V.DC
22 F
30, 50 F
70 F
Capacitance change ±30 % of initial measured value at +20 °C (at –25 °C)
Internal resistance < 4 times of initial measured value at +20 °C (at –25 °C)
After 1000 hours application of 2.3 V.DC at +70 °C (+60 °C), the capacitor shall meet the
following limits.
Endurance
Capacitance change ±30 % of initial measured value
Internal resistance < 2 time of initial specified value
After 1000 hours storage at +70 °C (+60 °C) without load, the capacitor shall meet the
specified limits for Endurance.
Shelf Life
Dimensions in mm(not to scale)
(Unit : mm)
Sleeve
0d±0.05
P±0.5
(>8.0 mm dia.)
Vent
L+2 max.
14 min.
0D+0.5 max.
3 min.
Capacitance
L
0D
(F)
22
18.0 35.0
0d
P
0.8
7.5
30
18.0 35.0
0.8
7.5
50
18.0 40.0
0.8
7.5
70
18.0 50.0
0.8
7.5
Characteristics list
✽ : 10 F or less HW series is not recommended for new design. Please consider HZ series.
Category Maximum
operating Capacitance
temp.
voltage
range
(F)
(V.DC)
(°C)
22
–25 to +70
2.3
–25 to +60
2.1
Capacitance
tolerance
(F)
17.6 to 30.8
Min.
Internal
Recommended
Mass
packaging
resistance
discharge
Parts number (Reference value)
q’ty
current
(Initial specified value)
(g)
(pcs)
(Ω) at 1 kHz
(A)
1 or less
EECHW0D226
12.0
50
< 0.1
30
24.0 to 42.0
< 0.1
1 or less
50
40.0 to 70.0
< 0.1
70
56.0 to 98.0
< 0.1
EECHW0D306
14.0
50
1 or less
EECHW0D506
15.0
50
1 or less
EECHW0D706
19.0
50
Note : 1. Do not use reflow soldering. (IR, Atmosphere heating methods, etc. )
Please refer to the page of “Application guidelines”.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
03
Jan. 2016
CAUTION AND WARNING
1. The electronic components contained in this catalog are designed and produced for use in home electric appliances, office eq uipment, information equipment,
communications equipment, and other general purpose electronic devices.
Before use of any of these components for equipment that requires a high degree of safety, such as medical instruments, aeros pace equipment, disaster-prevention
equipment, security equipment, vehicles (automobile, train, vessel),
please be sure to contact our sales representative.
2. When applying one of these components for equipment requiring a high degree of safety, no matter what sort of application it might be, be sure to install a protective
circuit or redundancy arrangement to enhance the safety of your equipment. In addition, please carry out the safety test on your own responsibility.
3. When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on thespecifications with us in advance.
4. Technical information contained in this catalog is intended to convey examples of typical performances and/or applications a nd is not intended to make any
warranty with respect to the intellectual property rights or any other related rights of our company or any third parties nor grant any license under such rights.
5. In order to export products in this catalog, the exporter may be subject to the export license requirement under the Foreign Exchange and Foreign Trade Law of
Japan.
6. No ozone-depleting substances (ODSs) under the Montreal Protocol are used in the manufacturing processes of Automotive & Ind ustrial Systems Company, Panasonic
Corporation.
Please contact
Factory
The information in this catalog is valid as of December 2015.
Similar pages