ESM1A THRU ESM1J

SURFACE MOUNT SUPER FAST RECTIFIER
ESM1A THRU ESM1J
VOLTAGE RANGE
50 to 600Volts
FORWARD CURRENT
1.0 Ampere
FEATURES
•
•
•
•
•
•
DO-213AB
For surface mounted applications
Glass passivated chip junction
Low leakage current
Fast switchig
Plastic package has underwrites laboratory flammability
Classification 94V-0
High temperature soldering guaranteed
250℃/10 seconds at terminals
MECHANICAL DATA
•
•
•
•
Dimensions in inches and (millimeters)
Case: molded plastic
Polarity: band indicate cathode
Mounting position: Any
Weight: 0.12 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
•
•
•
Ratings at 25℃ ambient temperature unless otherwise specified
Single Phase, half wave, 60Hz, resistive or inductive load
For capacitive load derate current by 20%
SYMBOLS
Maximum Repetitive Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current at T T=100℃
Peak Forward Surge Current
8.3ms single half sine wave superimposed on
rated load (JEDEC Method)
Maximum Instantaneous Forward Voltage at 1.0A
Maximum DC Reverse Current
at rated DC Blocking Voltage at
TA = 25℃
TA = 125℃
Typical Reverse Recovery Time (NOTE 1)
Typical Junction Capacitance (Note 2)
Typical Thermal Resistance (Note 3)
Operating and Storage Temperature Range
VRRM
VRMS
VDC
I(AV)
ESM
1A
50
35
50
ESM
1B
100
70
100
ESM
1C
150
105
150
IFSM
VF
ESM
1D
200
140
200
1.0
ESM
1E
300
210
300
ESM
1J
600
420
600
ESM
1G
400
280
400
30
095
IR
Trr
CJ
RθJT
TJ,TSTG
Notes:
1. Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
2. Measured at 1.0MHz and applied reverse voltage of 4.0 Volts.
3. Thermal resistance Junction to terminal 6.0mm2 copper pads to each terminal.
Web Site: www.hkmic.com
UNITS
Volts
Volts
Volts
Amps
Amps
1.25
5.0
100
35
15
40
-55 to +150
1.7
Volts
µA
ns
PF
℃/W
℃
SURFACE MOUNT SUPER FAST RECTIFIER
ESM1A THRU ESM1J
VOLTAGE RANGE
50 to 600Volts
FOEWARD CURRENT
1.0 Ampere
RATINGS AND CHARACTERISTIC CURVES ESM1A THRU ESM1J
FIG.1-MAXMUM FORWARD CURRENT
FIG.2-MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
DERATING CURVE
1.0
0.8
0.6
0.4
Resistive or Inductive Load
0.2
P.C.B Mounted
0.2x0.2"(5.0x5.0mm)
Copper Pad Areas
0
80
90
100
110
120
130
140
150
PEAK FORWARD SURGE CURRENT,(A)
AVERAGE FORWARD CURRENT(A)
1.2
30
8.3ms Single Half Sine-Wave
(JEDEC Method)T =110°
c
T
25
20
15
10
5.0
0
1
10
100
NUMBER OF CYCLES AT 60 Hz
FIG.4-TYPICAL REVERSE LEAKAGE
CHARACTERISTICS
0.01
0.001
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
INSTANTANEOUS FORWARD VOLTAGE,(V)
FIG.5-TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE,(pF)
60
T =25°
J
C
Pulse Width=300us
1% Duty Cycle
50
40
30
20
10
0
0.1
1.0
10
100
INSTANTANEOUS REVERSE CURRENT,(uA)
T J=25° C
Pulse Width=300us
1% Duty Cycle
TRANSIENT THERMAL IMPEDANCE(℃/W)
ES
M
1J
M
ES
M1
0.1
A -1
D
1E
-1
G
1.0
ES
INSTANTANEOUS FORWARD CURRENT,(A)
FIG.3-TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
5.0
1000
T J=125° C
100
10
T J=75° C
1.0
T =25°
J
C
0.1
0.01
0
20
40
60
80
100
PERCENT OF RATED PEAK
REVERSE VOLTAGE,(%)
FIG.6-TRANSIENT THERMAL IMPEDANCE
100
Mounted on
0.20x0.27"(5.0x7.0mm)
Copper Land Areas
10
1
0.1
1.0
10
T,PULSE DURATION(SEC.)
REVRESE VOLTAGE,(V)
Web Site: www.hkmic.com
100
Similar pages