Conductive Polymer Hybrid Aluminum Electrolytic Capacitors Surface Mount Type Series : ZC Type : V High temperature Lead-Free reflow Features ● Endurance: 4000 h at 125 °C (High temperature / Long life) ● Low ESR and high ripple current (85 % over, Lower ESR than current V-TP) ● High-withstand voltage (25 V.DC to 80 V.DC), Low LC (0.01 CV or 3 μA) ● Equivalent to conductive polymer type aluminum electrolytic capacitor (There are little characteristics change by temperature and frequency) available upon request. (08 mm and larger) ● Vibration-proof product is ● AEC-Q200 compliant ● RoHS directive compliant Specifications Size code C D D8 F G Category temp. range –55 °C to +125 °C Rated voltage range 25 V.DC to 50 V.DC 25 V.DC to 63 V.DC 25 V.DC to 80 V.DC Nominal cap.range 10 μF to 33 μF 10 μF to 56 μF 22 μF to 100 μF 22 μF to 220 μF 33 μF to 330 μF Capacitance tolerance ±20 % (120 Hz/+20 °C) DC leakage current I < 0.01 CV or 3 (μA) After 2 minutes (whichever is greater) Dissipation factor (tan d) Please see the attached standard products list 125 °C, 4000 h, apply the rated ripple current without exceeding the rated voltage Capacitance change Within ±30% of the initial value Endurance 1 tan d < 200 % of the initial limit E. S. R. < 200 % of the initial limit DC leakage current Within the initial limit 125 °C, 3000 h, apply the rated ripple current without exceeding the rated voltage Capacitance change Within ±30% of the initial value Endurance 2 tan d < 200 % of the initial limit E. S. R. < 300 % of the initial limit DC leakage current Within the initial limit After storage for 1000 hours at +125 °C±2 °C with no voltage applied and then being stabilized at +20 °C, Shelf life capacitors shall meet the limits speciﬁed in Endurance. (With voltage treatment) 85 °C, 85 % to 95 %, 2000 h, rated voltage applied Capacitance change Within ±30% of the initial value Damp heat (Load) tan d < 200 % of the initial limit E. S. R. < 200 % of the initial limit DC leakage current Within the initial limit After reﬂow soldering and then being stabilized at +20 °C, capacitors shall meet the following limits. Capacitance change Within ±10% of the initial value Resistance to soldering heat tan d Within the initial limit DC leakage current Within the initial limit 0.3 max. A±0.2 Capacitance (μF) Series identiﬁcation L Pressure relief (010 and larger) B±0.2 33 E ZC 0D±0.5 Negative polarity marking (–) H – + (P) Marking color : BLACK (I) Example : 25 V.DC 33 μF W ( ) Reference size (Unit : mm) Rated voltage mark Lot number Size code Rated voltage mark E V H 25 V.DC 35 V.DC 50 V.DC J K 63 V.DC 80 V.DC (I) Dimensions (not to scale) K Marking D L A, B C 5.0 5.8±0.3 5.3 D 6.3 5.8±0.3 6.6 D8 6.3 7.7±0.3 6.6 F 8.0 10.2±0.3 8.3 G 10.0 10.2±0.3 10.3 H 6.5 max. 7.8 max. 7.8 max. 10.0 max. 12.0 max. I 2.2 2.6 2.6 3.4 3.5 W 0.65±0.1 0.65±0.1 0.65±0.1 0.90±0.2 0.90±0.2 P 1.5 1.8 1.8 3.1 4.6 K 0.15 0.35 +- 0.20 0.15 0.35 +- 0.20 0.15 0.35 +- 0.20 0.70±0.2 0.70±0.2 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 04 Jan. 2016 NEW NEW NEW NEW NEW

- Similar pages