MCP39F511N
Power Monitor
Demonstration Board
User’s Guide
2015 Microchip Technology Inc.
DS50002445A
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer,
LANCheck, MediaLB, MOST, MOST logo, MPLAB,
OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC,
SST, SST Logo, SuperFlash and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
The Embedded Control Solutions Company and mTouch are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo,
CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit
Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet,
KleerNet logo, MiWi, motorBench, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, RightTouch logo, REAL ICE, SQI, Serial Quad I/O,
Total Endurance, TSHARC, USBCheck, VariSense,
ViewSpan, WiperLock, Wireless DNA, and ZENA are
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2015, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
ISBN: 978-1-5224-0104-9
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
DS50002445A-page 2
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
2015 Microchip Technology Inc.
Object of Declaration: MCP39F511N Power Monitor Demonstration Board
VP Development Tools
2015 Microchip Technology Inc.
DS50002445A-page 3
MCP39F511N Power Monitor Demonstration Board User’s Guide
NOTES:
DS50002445A-page 4
2015 Microchip Technology Inc.
MCP39F511N POWER MONITOR
DEMONSTRATION BOARD
USER’S GUIDE
Table of Contents
Preface ........................................................................................................................... 7
Introduction............................................................................................................ 7
Document Layout .................................................................................................. 7
Conventions Used in this Guide ............................................................................ 8
Recommended Reading........................................................................................ 9
The Microchip Web Site ........................................................................................ 9
Customer Support ................................................................................................. 9
Document Revision History ................................................................................... 9
Chapter 1. Product Overview
1.1 Introduction ................................................................................................... 11
1.2 What the MCP39F511N Power Monitor Demonstration Board Kit
Includes .................................................................................................. 12
Chapter 2. Installation and Operation
2.1 Getting Started ............................................................................................. 13
Chapter 3. Hardware Description
3.1 Input and Analog Front End ......................................................................... 17
3.2 Power Supply Circuit .................................................................................... 18
Appendix A. Schematic and Layouts
A.1 Introduction .................................................................................................. 19
A.2 Schematics and PCB Layout ....................................................................... 19
A.3 Board – Schematic ....................................................................................... 20
A.4 Board – Schematic (Continued) ................................................................... 21
A.5 Board – Top Silk .......................................................................................... 22
A.6 Board – Top Copper and Silk ....................................................................... 23
A.7 Board – Top Copper .................................................................................... 24
A.8 Board – Bottom Copper ............................................................................... 25
A.9 Board – Bottom Copper and Silk ................................................................. 26
A.10 Board – Bottom Silk ................................................................................... 27
Appendix B. Bill of Materials (BOM)........................................................................... 29
Worldwide Sales and Service .................................................................................... 32
2015 Microchip Technology Inc.
DS50002445A-page 5
MCP39F511N Power Monitor Demonstration Board User’s Guide
NOTES:
DS50002445A-page 6
2015 Microchip Technology Inc.
MCP39F511N POWER MONITOR
DEMONSTRATION BOARD
USER’S GUIDE
Preface
NOTICE TO CUSTOMERS
All documentation becomes dated, and this manual is no exception. Microchip tools and
documentation are constantly evolving to meet customer needs, so some actual dialogs
and/or tool descriptions may differ from those in this document. Please refer to our web site
(www.microchip.com) to obtain the latest documentation available.
Documents are identified with a “DS” number. This number is located on the bottom of each
page, in front of the page number. The numbering convention for the DS number is
“DSXXXXXXXA”, where “XXXXXXX” is the document number and “A” is the revision level of
the document.
For the most up-to-date information on development tools, see the MPLAB® IDE online help.
Select the Help menu, and then Topics to open a list of available online help files.
INTRODUCTION
This chapter contains general information that will be useful to know before using the
MCP39F511N Power Monitor Demonstration Board. Items discussed in this chapter
include:
•
•
•
•
•
•
Document Layout
Conventions Used in this Guide
Recommended Reading
The Microchip Web Site
Customer Support
Document Revision History
DOCUMENT LAYOUT
This document describes how to use the MCP39F511N Power Monitor Demonstration
Board as a demonstration board to evaluate the MCP39F511N device. The manual
layout is as follows:
• Chapter 1. “Product Overview” – Provides important information about the
MCP39F511N Power Monitor Demonstration Board
• Chapter 2. “Installation and Operation” – Provides information on using the
MCP39F511N Power Monitor Demonstration Board, including
Section 2.1.1 “Step 1: Wiring connections” that describes wiring the line and
load connections
• Chapter 3. “Hardware Description” – Provides details on the functional blocks
of the power monitor, including the analog front-end design and power supply
design
• Appendix A. “Schematic and Layouts” – Shows the schematic and layout
diagrams
• Appendix B. “Bill of Materials (BOM)” – Lists the parts used to build the
MCP39F511N Power Monitor Demonstration Board
2015 Microchip Technology Inc.
DS50002445A-page 7
MCP39F511N Power Monitor Demonstration Board User’s Guide
CONVENTIONS USED IN THIS GUIDE
This manual uses the following documentation conventions:
DOCUMENTATION CONVENTIONS
Description
Arial font:
Italic characters
Initial caps
Quotes
Underlined, italic text with
right angle bracket
Bold characters
N‘Rnnnn
Text in angle brackets < >
Courier New font:
Plain Courier New
Represents
Referenced books
Emphasized text
A window
A dialog
A menu selection
A field name in a window or
dialog
A menu path
MPLAB® IDE User’s Guide
...is the only compiler...
the Output window
the Settings dialog
select Enable Programmer
“Save project before build”
A dialog button
A tab
A number in verilog format,
where N is the total number of
digits, R is the radix and n is a
digit.
A key on the keyboard
Click OK
Click the Power tab
4‘b0010, 2‘hF1
Italic Courier New
Sample source code
Filenames
File paths
Keywords
Command-line options
Bit values
Constants
A variable argument
Square brackets [ ]
Optional arguments
Curly brackets and pipe
character: { | }
Ellipses...
Choice of mutually exclusive
arguments; an OR selection
Replaces repeated text
Represents code supplied by
user
DS50002445A-page 8
Examples
File>Save
Press <Enter>, <F1>
#define START
autoexec.bat
c:\mcc18\h
_asm, _endasm, static
-Opa+, -Opa0, 1
0xFF, ‘A’
file.o, where file can be
any valid filename
mcc18 [options] file
[options]
errorlevel {0|1}
var_name [,
var_name...]
void main (void)
{ ...
}
2015 Microchip Technology Inc.
Preface
RECOMMENDED READING
This user's guide describes how to use MCP39F511N Power Monitor Demonstration
Board. Another useful document is listed below. The following Microchip document is
available and recommended as a supplemental reference resource:
MCP39F511N Data Sheet – “Dual-Channel, Single-Phase Power-Monitoring IC
with Calculation” (DS20005473)
This data sheet provides detailed information regarding the MCP39F511N device.
THE MICROCHIP WEB SITE
Microchip provides on-line support via our web site at www.microchip.com. This web
site is used as a means to make files and information easily available to customers.
Accessible by using your favorite Internet browser, the web site contains the following
information:
• Product Support – Data sheets and errata, application notes and sample
programs, design resources, user’s guides and hardware support documents,
latest software releases and archived software
• General Technical Support – Frequently Asked Questions (FAQs), technical
support requests, on-line discussion groups, Microchip consultant program
member listing
• Business of Microchip – Product selector and ordering guides, latest Microchip
press releases, listing of seminars and events, listings of Microchip sales offices,
distributors and factory representatives
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels:
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Customers should contact their distributor, representative or field application engineer
(FAE) for support. Local sales offices are also available to help customers. A listing of
sales offices and locations is included in the back of this document.
Technical support is available through the web site at: http://support.microchip.com
DOCUMENT REVISION HISTORY
Revision A (December 2015)
• Initial Release of this Document.
2015 Microchip Technology Inc.
DS50002445A-page 9
MCP39F511N Power Monitor Demonstration Board User’s Guide
NOTES:
DS50002445A-page 10
2015 Microchip Technology Inc.
MCP39F511N POWER MONITOR
DEMONSTRATION BOARD
USER’S GUIDE
Chapter 1. Product Overview
1.1
INTRODUCTION
The MCP39F511N Power Monitor Demonstration Board is a fully functional
dual-channel single-phase power and energy monitor. For each channel, the system
calculates active power, reactive power, RMS current, RMS voltage, active energy,
(both import and export), reactive energy and other typical power quantities for two
separate loads, as defined in the MCP39F511N data sheet.
The MCP39F511 Power Monitor Utility software is used to calibrate and monitor the
system, and can be used to create custom calibration setups. For most accuracy
requirements, only a single-point calibration is needed. The energy meter software
offers an automated step-by-step calibration process that can be used to quickly
calibrate energy meters.
This demonstration board uses the Power Monitor Utility Software for evaluation via a
USB connection to the board. A download link for this software can be found on the
evaluation board’s web page. For instructions on the use of this software, refer to the
software’s supporting documentation included within the application install package.
FIGURE 1-1:
2015 Microchip Technology Inc.
MCP39F511N Power Monitor Demonstration Board.
DS50002445A-page 11
MCP39F511N Power Monitor Demonstration Board User’s Guide
1.2
WHAT THE MCP39F511N POWER MONITOR DEMONSTRATION BOARD KIT
INCLUDES
This MCP39F511N Power Monitor Demonstration Board kit includes:
•
•
•
•
•
DS50002445A-page 12
MCP39F511N Power Monitor Demonstration Board (ADM00706)
AC Line Cable
Two IEC-to-Female AC Load Cables
Mini-USB Cable
Important Information Sheet
2015 Microchip Technology Inc.
MCP39F511N POWER MONITOR
DEMONSTRATION BOARD
USER’S GUIDE
Chapter 2. Installation and Operation
2.1
GETTING STARTED
To use the MCP39F511N Power Monitor Demonstration Board, follow the steps
described in the sections below. The meter design uses a 5A load for calibration current
and a maximum current (IMAX) of 15A.
It is not recommended to put more than 15A through the AC plugs mounted on the
Printed Circuit Board (PCB).
To test the calibrated meter, the following connections can be made:
2.1.1
Step 1: Wiring connections
Figure 2-1 identifies the line and two load connections of the MCP39F511N Power
Monitor Demonstration Board.
FIGURE 2-1:
Board.
2015 Microchip Technology Inc.
Connecting the MCP39F511N Power Monitor Demonstration
DS50002445A-page 13
MCP39F511N Power Monitor Demonstration Board User’s Guide
2.1.2
Step 2: Connect line/load power to the meter (power the meter)
The meter will turn on when the line connection has between 90V to 220V connected.
One or two loads can be connected to the meter.
2.1.3
Step 3: Connect the USB cable to a PC with the installed
MCP39F511N Power Monitor Utility software
Select the appropriate COM port. If the meter is connected correctly, the connection
status in the bottom left corner of the software will display “Meter Connected”. If no
meter is found, the status will be “Meter Disconnected”. Check that the correct COM
port was selected and try again. Press the Start Icon to begin showing output data and
UART transmission between the PC and the MCP39F511N.
DS50002445A-page 14
2015 Microchip Technology Inc.
MCP39F511N POWER MONITOR
DEMONSTRATION BOARD
USER’S GUIDE
Chapter 3. Hardware Description
7
6
8
9
5
10
13
11
4
2
12
3
1
Legend:
1 = MCP39F511N
8
=
Header for connection to external master
MCU (isolated)
2 = +9V DC Input (nonisolated)
9
=
Jumper selection for external MCU or USB
(GUI) operation
3 = Current Sensing Shunt - Channel 1
10
=
Isolation IC
4 = Current Sensing Shunt - Channel 2
11
=
Switching AC/DC Power Supply
5 = Output LEDs for digital I/O
12
=
200:1 Voltage Divider for Voltage Input
6 = Headers for digital I/O testing (isolated)
13
=
Jumper for DC or Switching AC/DC Supply
7 = USB Connection (isolated)
FIGURE 3-1:
MCP39F511N Power Monitor Demonstration Board Top View.
2015 Microchip Technology Inc.
DS50002445A-page 15
MCP39F511N Power Monitor Demonstration Board User’s Guide
16
14
15
Legend:
14
=
Line connection AC supply (80-230V)
15
=
Load connection for Channel 1 (15 A maximum recommended current)
16
=
Load connection for Channel 2 (15 A maximum recommended current)
FIGURE 3-2:
DS50002445A-page 16
MCP39F511N Power Monitor Demonstration Board Bottom View.
2015 Microchip Technology Inc.
Hardware Description
3.1
INPUT AND ANALOG FRONT END
The MCP39F511N Power Monitor Demonstration Board will operate from 80V to 230V.
At the bottom of the main board, there are the high-voltage line and neutral
connections. The shunts sit on the neutral or low-side of a two-wire system. The board
comes populated with two surface mount 2 m shunts.
The line side of the two-wire system goes into a resistive divider on the voltage channel
input, along with a DC offset added from VDD. Anti-aliasing low-pass filters are
included. The voltage channel uses two 499 k resistors and the additional
components to achieve a divider ratio of approximately 236:1. For a line voltage of
236 VRMS, the channel 1 input signal size will be 1VRMS with a DC offset voltage of
DVDD/2 per the schematic snippet below.
L
N
1 k
+
I1LOAD
-
2 m
33 nF
1 k
I1+
33 nF
+
1 k
LOAD
-
2 m
I233 nF
MCP39F511N
1 k
I2+
33 nF
+3.3V
499 k 499 k
51 k
47 µ F
1 k
+
5.1 k
L
33 nF
51 k
V+
33 nF
N
FIGURE 3-3:
Analog Front-End Circuitry.
Note that all of the analog circuitry associated with this part of the circuit is connected
to the analog ground plane (AGND).
2015 Microchip Technology Inc.
DS50002445A-page 17
MCP39F511N Power Monitor Demonstration Board User’s Guide
3.2
POWER SUPPLY CIRCUIT
FB
The power supply circuit for the MCP39F511N Power Monitor Demonstration Board is
shown in Figure 3-4.
BP
D
150 FB 47 47
L
+ 4.7 µF
150 FB
+
LNK304
S
S
S
S
0.1 µF
8.2K
10 µF
2.05K
1 mH
4.7 µF
8.25V
100 µF+ 2.05K
N
GNDB
GNDB
GNDB
GNDB
GNDB
GNDB
8.25V
+3.3 VD
+3.3 VA
‘
33
0.1 µF 10 µF
MCP1754
JP2
AGND
AC/DC SUPPLY
DC SUPPLY
1
GNDB
3
2
IN
0.1 µF
DS50002445A-page 18
0.1 µF
10 µF
NT
GNDB
FIGURE 3-4:
Supply.
OUT
GND
AGND
GNDB
AGNDGNDB GNDB
Power Supply Circuit with Option for AC/DC Switching Supply from Mains or DC
2015 Microchip Technology Inc.
MCP39F511N POWER MONITOR
DEMONSTRATION BOARD
USER’S GUIDE
Appendix A. Schematic and Layouts
A.1
INTRODUCTION
This appendix contains the following schematics and layouts for of the MCP39F511N
Power Monitor Demonstration Board:
•
•
•
•
•
•
•
•
A.2
Board – Schematic
Board – Schematic (Continued)
Board – Top Silk
Board – Top Copper and Silk
Board – Top Copper
Board – Bottom Copper
Board – Bottom Copper and Silk
Board – Bottom Silk
SCHEMATICS AND PCB LAYOUT
The layer order is shown in Figure A-1.
Top Layer
Bottom Layer
FIGURE A-1:
2015 Microchip Technology Inc.
Layer Order.
DS50002445A-page 19
BOARD – SCHEMATIC
$
'
&
&
9
X)
9
X)
$*1'
$
$
5
*1'%
N
&XUUHQWFKDQQHO
1(875$/B287
5
5
$*1'
&
,
X)
9
,
,
1(875$/
$*1'
&
5
)%
5(6(7
,
/LQHVKXQW
N
$9''
5
)%
73
8
X)
9
N
'
$*1'
5(),1287
'9''
733$'3&%[
&20021B$ &20021B% 3:0
(9(17 (9(17 1&
1& 1& 1& 9
=&' '*1'
'*1'
(3
1(875$/
&
5
5
5
N
$*1'
5
)%
1(875$/B287
&
X)
9
2015 Microchip Technology Inc.
/LQHVKXQW
)%
N
&
X)
9
&
X) 9
9
X)
$*1' $*1'
0&3)1
*1'%
92/7$*(B$'&B,1
=&'
26&, 26&2
'5
&XUUHQWFKDQQHO
3:0
(9(17
(9(17
8$57B7;
8$57B5;
0&/5
038B7;
038B5;
038B0&/5
5
N
'
MCP39F511N Power Monitor Demonstration Board User’s Guide
DS50002445A-page 20
A.3
BOARD – SCHEMATIC (CONTINUED)
5VUSB
C31
C30
GND_ISO
USB_N
USB_P
5VUSB
4.7uF
10V
0805
C29
5VUSB
R35
10k
0603
1%
1
2
3
4
5
6
7
RX_LED
TX_LED
RESET
RX
TX
GND_ISO
LD5
1
5VUSB
VDD
GP0
GP1
RST
UART RX
UART TX
GP2
VSS
D+
DVUSB
SCL
SDA
GP3
14
13
12
11
10
9
8
3
R34
0603
1%
RX_LED
2
R33
0603
1%
TX_LED
1k
1k
25V
0.1uF
0603
GND_ISO
GND_ISO
USB_P
USB_N
VUSB
MCP2221
GREEN
4
U11
C32
0.47uF
6.3V
0603
RX
R32
0603
5%
TX
R31
0603
5%
100R
100R
GND_ISO
VOLTAGE DIVIDER
0603
5%
MPU_TX1
R21
0603
5%
MPU_RX1
100R
100R
GNDB
External isolated serial comm
HDR-2.54 Male 1x4
4
D
FB4
0.01uF
330V
RAD-P10L13W4H9
R10
D2
470R
2512
5%
470R
2512
5%
MRA4005
6
S
5
S
8.2k
0603
1%
S
R16
2.05k
0603
1%
1
R4
R17
L2
C17
1mH
C10
C11
4.7uF
4.7uF
400V
400V
RAD_P3.5D8H13 RAD_P3.5D8H13
0.1uF
25V
0603
C18
4.7uF
25V
0805
D4
MRA4005
L1
1mH
+8.25V
C6
100uF
16V
AL-D
D1
ES1G
GND_PWR
R12
FB3
1
3
2
POWER 2.5mm
+9V IN
MRA4005
C24
10uF
25V
1206
GNDB
C26
25V
0.1uF
0603
GNDB
MCP1754S/3.3V
VIN
VOUT
V
GNDB
C27
G
N
1
2
3
1
LINE
2
EARTH
NEUTRAL
[SHUNT]
NEUTRAL_OUT1
3
DS50002445A-page 21
IEC Inlet C14
L
N
IEC Outlet C13
J4
LINE
1
2
NEUTRAL
[SHUNT]
NEUTRAL_OUT2
3
L
G
N
IEC Outlet C13
AGND
NT1
Net Tie
GNDB
G
10uF
10V
0805
GNDB
J2
L
C22
25V
0.1uF
0603
GNDB
J1
0603
5%
33R
C25
10uF
10V
0805
GNDB
3.3A
R20
3
AGND
C23
25V
0.1uF
0603
AGND
Schematic and Layouts
+9V IN
POWER
D3
1
Vin
HDR-2.54 Male 1x3
J3
3.3D
U5
JP2
2.05k
0603
1%
GND
FB
2
U3
8 LNK304
S
7
S
3 2 1
NEUTRAL
R22
5VUSB
BP
DISC 14mm
S14K275
GNDB
Yes
GND_ISO
C1
25V
0.1uF
0603
J5
EXT_RX
EXT_TX
RED
MOV1
3.3D
ACSL-7210
HDR-2.54 Male 1x3
RED, GREEN
LINE
C28
U6
1
8
VDD1 VDD2
2
7
VOA
VIA
3
6
VIB
VOB
4
5
GND1 GND2
GND_ISO
JP3
3.3D
5VUSB
2
GND_ISO
Isolation
Barrier
5VUSB
GND_ISO
1 2 3 4
USB MINI-B Female
1
VBUS
2
D3
D+
4
ID
5
GND
25V
0.1uF
0603
5VUSB
1
2
3
J10
0
2015 Microchip Technology Inc.
A.4
MCP39F511N Power Monitor Demonstration Board User’s Guide
A.5
BOARD – TOP SILK
DS50002445A-page 22
2015 Microchip Technology Inc.
Schematic and Layouts
A.6
BOARD – TOP COPPER AND SILK
2015 Microchip Technology Inc.
DS50002445A-page 23
MCP39F511N Power Monitor Demonstration Board User’s Guide
A.7
BOARD – TOP COPPER
DS50002445A-page 24
2015 Microchip Technology Inc.
Schematic and Layouts
A.8
BOARD – BOTTOM COPPER
2015 Microchip Technology Inc.
DS50002445A-page 25
MCP39F511N Power Monitor Demonstration Board User’s Guide
A.9
BOARD – BOTTOM COPPER AND SILK
DS50002445A-page 26
2015 Microchip Technology Inc.
Schematic and Layouts
A.10 BOARD – BOTTOM SILK
2015 Microchip Technology Inc.
DS50002445A-page 27
MCP39F511N Power Monitor Demonstration Board User’s Guide
NOTES:
DS50002445A-page 28
2015 Microchip Technology Inc.
MCP39F511N POWER MONITOR
DEMONSTRATION BOARD
USER’S GUIDE
Appendix B. Bill of Materials (BOM)
TABLE B-1:
BILL OF MATERIALS (BOM)
Qty. Reference
Description
Manufacturer
Part Number
1
C1
Capacitor film 0.01 µF 330V 20% RAD
P10L13W4H9
EPCOS AG
B32911A3103M
6
C2, C3, C4,
C5, C7, C15
Capacitor ceramic 0.033 µF 50V 10%
X7R SMD 0603
TDK Corporation
C1608X7R1H333K
1
C6
Capacitor alum. 100 µF 16V 20% SMD D
Nichicon Corporation
UWX1C101MCL1GB
3
C8, C22,
C25
Capacitor ceramic 10 µF 10V 10% X7R
SMD 0805
TDK Corporation
C2012X7R1A106K125AC
10
C9, C12,
C13, C17,
C23, C26,
C27, C28,
C29, C31
Capacitor ceramic 0.1 µF 25V 10% X7R
SMD 0603
Murata Electronics
GRM188R71E104KA01D
2
C10, C11
Capacitor alum. 4.7 µF 400V 20%
RAD_P3.5D8H13
Nichicon Corporation
UVC2G4R7MPD1TD
1
C14
Capacitor tantalum 47 µF 4V 10%
2.6Ohm SMD A
AVX Corporation
TAJA476K004RNJ
1
C18
Capacitor ceramic 4.7 µF 25V 10% X7R
SMD 0805
TDK Corporation
C2012X7R1E475K125AB
1
C24
Capacitor ceramic 10 µF 25V 10% X7R
SMD 1206
Taiyo Yuden Co., Ltd.
TMK316B7106KL-TD
1
C30
Capacitor ceramic 4.7 µF 10V 10% X5R
SMD 0805
Taiyo Yuden Co., Ltd.
LMK212BJ475KD-T
1
C32
Capacitor ceramic 0.47 µF 6.3V 10% X5R Murata Electronics®
SMD 0603
GRM188R60J474KA01D
1
CBL1
Mech. HW cable USB-A male-to-mini
USB-B male 3 ft black
Katerno
10UM-02103BK
2
CBL2, CBL3
Mech. HW 1ft 18 AWG monitor power
adapter cord (NEMA 5-15R to
IEC320C14)
Katerno
152360
1
CBL4
Mech. HW 6 ft 16 AWG universal power
cord (IEC320C13 to NEMA 5-15P)
Katerno
153879
1
D1
Diode rectifier ES1G 1.25V 1A 400V SMD Diodes® Incorporated
DO-214AC_SMA
3
D2, D3, D4
Diode rectifier MRA4005 1.1V 1A 600V
DO-214AC_SMA
ON Semiconductor®
MRA4005T3G
1
ENCLOSURE1
Mech. enclosure slim ref. side port meter
Tech-Demos.com
TD03-0102R0
4
FB1, FB2,
FB5, FB6
Ferrite 800mA 0.15R SMD 0805
Laird Technologies®
LI0805H151R-10
2
FB3, FB4
Ferrite 7A RAD P5L5.3D3.8
Murata Electronics
North America, Inc.
BL02RN1R2M2B
Note 1:
ES1G-13-F
The components listed in this Bill of Materials are representative of the PCB assembly. The released
BOM used in manufacturing uses all RoHS-compliant components.
2015 Microchip Technology Inc.
DS50002445A-page 29
Bill of Materials (BOM)
TABLE B-1:
BILL OF MATERIALS (BOM) (CONTINUED)
Qty. Reference
Description
Manufacturer
Part Number
1
J1
Conn. IEC 250V 15A inlet C14 TH R/A
SCHURTER Inc.
GSP1.9103.1
2
J2, J4
Conn. IEC 250V 15A outlet C13 TH R/A
SCHURTER Inc.
6182.0033
1
J3
Conn. pwr. 2.5mm 5.5mm switch TH R/A
CUI Inc.
PJ-002B
1
J5
Conn. header-2.54 male 1x4 tin 5.84 MH
TH vert.
FCI
68002-404HLF
4
J6, J7, J8, J9 Conn. header-2.54 male 1x2 tin 6.10 MH
TH vert.
Molex®
0022284020
1
J10
Conn. USB mini-B female TH vert.
Molex® Connector
Corporation
500075-1517
2
JP2, JP3
Conn. header-2.54 male 1x3 gold 5.84
MH TH vert.
FCI
68000-103HLF
2
JP4, JP5
Mech. HW jumper 2.54 mm 1x2 handle
gold
TE Connectivity, Ltd.
881545-2
2
L1, L2
Inductor 1 mH 240 mA 20% SMD
L6W6H2.4
Coilcraft®
LPS6225-105MRB
1
LABEL1
Label, NEED HELP WITH ASSY/SERIAL
1
LABEL2
Mech. HW LABEL HIGH VOLTAGE
Panduit Corp.
PLD-56
4
LD1, LD2,
LD3, LD4
Diode LED red 1.95V 30 mA 700 MCD
clear SMD 0603
Kingbright Electronic
Co., Ltd.
APTD1608SURCK
1
LD5
Diode LED bi. red, green 1.95V, 2.1V 30
mA 0805
Kingbright Corp.
APHBM2012SURKCGKC
1
MOV1
Resistor varistor 275V 130J TH disc 14 mm EPCOS AG
6
NUT1,
Hex. nut 0.217" steel M3
NUT2,
NUT3,
NUT4,
NUT5, NUT6
Keystone Electronics
Corp.
4708
1
PCB1
Printed Circuit Board – MCP39F501
Power Monitor Demonstration Board
Microchip Technology
Inc.
04-10480-1
2
R1, R9
Resistor shunt MF 0.002R 1% 2W 2512
Stackpole Electronics,
Inc.
CSNL2512FT2L00
2
R2, R3
Res. TKF 499k 1% 3/4W SMD 2010
Vishay/Dale
CRCW2010499KFKEF
2
R4, R10
Res. TKF 470R 5% 1W SMD 2512
Panasonic® - ECG
ERJ-1TYJ471U
15
R5, R6, R7,
R11, R18,
R23, R24,
R25, R26,
R27, R28,
R29, R30,
R33, R34
Res. TKF 1k 1% 1/10W SMD 0603
Panasonic - ECG
ERJ-3EKF1001V
1
R8
Res. TKF 5.1k 1% 1/10W SMD 0603
Panasonic - ECG
ERJ-3EKF5101V
2
R12, R16
Res. TKF 2.05k 1% 1/10W SMD 0603
Yageo Corporation
RC0603FR-072K05L
2
R13, R14
Res. TKF 4.7k 1% 1/10W SMD 0603
Panasonic - ECG
ERJ-3EKF4701V
2
R15, R19
Res. TKF 51k 1% 1/10W SMD 0603
Panasonic - ECG
ERJ-3EKF5102V
1
R17
Res. TKF 8.2k 1% 1/10W SMD 0603
Panasonic - ECG
ERJ-3EKF8201V
1
R20
Res. TKF 33R 5% 1/10W SMD 0603
Yageo Corporation
9C06031A33R0JLHFT
4
R21, R22,
R31, R32
Res. TKF 100R 5% 1/10W SMD 0603
Vishay/Dale
CRCW0603100RJNEA
Note 1:
S14K275E2K1
The components listed in this Bill of Materials are representative of the PCB assembly. The released
BOM used in manufacturing uses all RoHS-compliant components.
2015 Microchip Technology Inc.
DS50002445A-page 30
Bill of Materials (BOM)
TABLE B-1:
BILL OF MATERIALS (BOM) (CONTINUED)
Qty. Reference
Description
Part Number
1
R35
Panasonic - ECG
ERJ-3EKF1002V
6
SCR1,
Machine screw pan Phillips M3
SCR2,
SCR3,
SCR4,
SCR5, SCR6
Digi-Key® Electronics
335-1156-ND
4
TP1, TP2,
TP4, TP5
Conn. TP pin tin TH
Harwin Plc.
H2121-01
1
U1
Microchip Analog Energy Measurement
4000:1 MCP39F511N-E/MQ QFN-28
Microchip Technology
Inc.
MCP39F511N-E/MQ
1
U3
IC switcher LNK304 SO-8C
Power Integrations™
LNK304DG-TL
1
U5
Microchip Analog LDO 3.3V
MCP1754ST-3302E/DB SOT-223-3
Microchip Technology
Inc.
MCP1754ST-3302E/DB
1
U6
IC photo ACSL-7210-06RE Bi-Dir. 3.3V
and 5V SOIC-8
Avago Technologies
ACSL-7210-06RE
4
U7, U8, U9,
U10
IC Photo HCPL-181 4-SMD
Avago Technologies
HCPL-181-00CE
1
U11
Microchip interface USB I2C UART
MCP2221-I/ST TSSOP-14
Microchip Technology
Inc.
MCP2221-I/ST
Note 1:
Resistor TKF 10k 1% 1/10W SMD 0603
Manufacturer
The components listed in this Bill of Materials are representative of the PCB assembly. The released
BOM used in manufacturing uses all RoHS-compliant components.
2015 Microchip Technology Inc.
DS50002445A-page 31
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Germany - Dusseldorf
Tel: 49-2129-3766400
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Austin, TX
Tel: 512-257-3370
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Canada - Toronto
Tel: 905-673-0699
Fax: 905-673-6509
China - Dongguan
Tel: 86-769-8702-9880
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
India - Pune
Tel: 91-20-3019-1500
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-213-7828
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Venice
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Poland - Warsaw
Tel: 48-22-3325737
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
07/14/15
DS50002445A-page 32
2015 Microchip Technology Inc.