LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SUPER BRIGHT ROUND TYPE LED LAMPS Pb Lead-Free Parts LHRF3333S/S259/A-PF DATA SHEET DOC. NO : QW0905-LHRF3333S/S259/A-PF REV. : A DATE : 30 -Oct.- 2014 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHRF3333S/S259/A-PF Page 1/6 Package Dimensions 5.0 5.9 7.6 8.6 1.5MAX 0.5 TYP 25.0MIN 1.0MIN 2.54TYP + Note : 1.All dimension are in millimeter tolerance is ±0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHRF3333S/S259/A-PF Page 2/6 Absolute Maximum Ratings at Ta=25 ℃ Ratings Parameter Symbol UNIT HRFS Forward Current IF 30 mA Peak Forward Current Duty 1/10@10KHz IFP 60 mA Power Dissipation PD 72 mW Ir 10 μA Electrostatic Discharge( * ) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Reverse Current @5V Typical Electrical & Optical Characteristics (Ta=25 ℃) PART NO LHRF3333S/S259/A-PF MATERIAL AlGaInP COLOR Emitted Lens Red Water Clear Forward Dominant Spectral voltage wave halfwidth @20mA(V) length △λnm λDnm Luminous intensity Viewing angle @20mA(mcd) 2θ 1/2 (deg) Min. Max. Min. 625 20 1.5 Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. 2.4 Typ. 3400 6200 30 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/6 PART NO. LHRF3333S/S259/A-PF Brightness Code For Standard LED Lamps Bin CHIP Group A27 A28 A29 A30 A31 A32 A33 Luminous Intensity(mcd) at 20 mA Min. Max. 3400 4000 5000 6200 7700 4000 5000 6200 7700 9500 9500 11500 11500 14000 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHRF3333S/S259/A-PF Page 4/6 Typical Electro-Optical Characteristics Curve HRFS CHIP Fig.2 Luminous Intensity vs. Forward Current 6.0 150 Luminous Intensity Normalize @20mA Forward Current(mA) Fig.1 Forward current vs. Forward Voltage 100 50 0 0 0.5 1.0 1.5 2.0 2.5 5.0 4.0 3.0 2.0 1.0 0.0 0 3.0 50 1.06 1.04 1.02 1.00 0.98 0.96 0.94 0 20 40 60 80 100 Relative Intensity@20mA Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0 600 650 Wavelength (nm) 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -40 -20 0 20 40 60 Ambient Temperature( ℃) Ambient Temperature( ℃) 550 Fig.4 Luminous Intensity vs. Temperature Luminous Intensity@20mA Normalize @25 ℃ Forward Voltage@20mA Normalize @25 ℃ Fig.3 Forward Voltage vs. Temperature -20 150 Forward Current(mA) Forward Voltage(V) -40 100 700 80 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LHRF3333S/S259/A-PF Page 5/6 Soldering Condition(Pb-Free) 1.Iron: Soldering Iron:30W Max Temperature 350°C Max Soldering Time:3 Seconds Max(One time only) Distance:2mm Min(From solder joint to body) 2.Wave Soldering Profile Dip Soldering Preheat: 120°C Max Preheat time: 60seconds Max Ramp-up 2°C/sec(max) Ramp-Down:-5° C/sec(max) Solder Bath:260°C Max Dipping Time:3 seconds Max Distance:2mm Min(From solder joint to body) Temp(¢XC) 260° C3sec Max 260° 5° C/sec max 120° 25° 0° 0 2° Csec max Preheat 60 Seconds Max 50 100 Note: 1.Wave solder should not be made more than one time. 2.You can just only select one of the soldering conditions as above. 150 Time(sec) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 6/6 PART NO. LHRF3333S/S259/A-PF Reliability Test: Test Item Test Condition Description Reference Standard Operating Life Test 1.Under Room Temperature 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) This test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. High Temperature High Humidity Test 1.Ta=65 ℃±5 ℃ 2.RH=90 %~95% 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hours. 1.Ta=105 ℃±5℃&-40 ℃±5℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5 ℃ 2.Dwell time= 10 ±1sec. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=245 ℃±5 ℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2 Thermal Shock Test JIS C 7021: B-12 MIL-STD-202:103B JIS C 7021: B-11