TLE6288R Data Sheet (790 KB, EN)

Data Sheet, Rev. 2.5, Oct. 2010
TLE6288R
Smart 6 Channel Peak & Hold Switch
Automotive Power
TLE6288R
Table of Contents
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
2.1
2.2
2.3
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3.1
3.2
General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4
4.1
4.1.1
4.1.2
4.2
4.3
4.3.1
4.3.2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gerneral Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Stage Control: Parallel Control and SPI Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current Regulator: Peak Current Control with Fixed Off-Time . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel Diagnostic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Characteristics: Diagnostic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
10
11
13
14
14
14
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Characteristics: SPI Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Commands, Values and Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit Assignment and Default Settings for Internal Logic Registers . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
16
17
18
19
21
22
6
6.1
6.2
6.3
6.4
Electrical Characteristics Input / Output Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply, Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
24
24
25
26
7
7.1
7.2
7.3
Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Zthjc Diagram Junction - Case for Single channel operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overload/Low Inductance Load Detection in Current Regulation Mode . . . . . . . . . . . . . . . . . . . . . . .
27
27
27
29
8
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Data Sheet
2
5
5
5
6
Rev. 2.5, 2010-10-11
TLE6288R
Features
•
•
•
•
•
•
•
3 Channel high side with adjustable Peak & Hold current
control
3 Channel high/low side configurable
Protection
– Overcurrent (current limitation)
– Overtemperature
– Overvoltage (active clamping)
Diagnosis
– Overcurrent
– Overtemperature
– Open load (Off-State)
– Short to Ground (Off-state, lowside configuration)
– Short to VB (Off-state, highside configuration)
• Electrostatic discharge (ESD) protection of all pins
Interface and Control
• Green Product (RoHS compliant)
– 16-Bit Serial Peripheral Interface (2 bit/CH)
• AEC Qualified
– Device programming via SPI
– Separate diagnosis output for each CH (DIAG1
Application
to 6)
– General Fault Flag + Overtemperature Flag
• Peak & Hold Loads (valves, coils)
– Direct parallel control of all channels
• Solenoids, Relays and Resistive Loads
– General enable signal to control all channels
• Fast protected Highside Switching
simultaneously
(PWM up to > 10 kHz)
Low Quiescent Current
Compatible with 3.3 V and 5 V microcontrollers
General Description
The TLE6288R is a 6-channel (150 mΩ) Smart Multichannel Switch in Smart Power Technology. The IC has
embedded protection, diagnosis and configurable functions. Channels 1-3 are highside channels with integrated
charge pump and can be programmed individually to do autonomous peak and hold current regulation with PWM.
Channel 4-6 (also with integrated charge pump) can be configured to work as highside switch or lowside switch.
This IC can be used to drive standard automotive loads in highside or lowside applications with switching
frequencies up to 10 kHz. In addition the TLE6288R can be used to drive autonomously up to 3 inductive
peak & hold (valves, coils) loads with programmable peak and hold current values.
Table 1
Product Summary
Parameter
Symbol
Values
Unit
VCC
On resistance
RDS(ON)1-6
Lowside clamping voltage Vcll(max)
Highside clamping voltage Vclh(max)
Peak current range
Ipk
Hold current range
Ihd
Peak time range
Ip
Fixed off time range
Ifo
4.5 … 5.5
V
0.15 typ. @ 25 °C
Ω
+55
V
-19
V
1.2 … 3.6
A
0.7 … 2
A
Type
Package
TLE6288R
PG-DSO-36-54
Logic Supply voltage
Data Sheet
3
0 … 3.6
ms
100 … 400
μs
Rev. 2.5, 2010-10-11
TLE6288R
Block Diagram
1
Block Diagram
Reset
VDO
DOUT 3 / VB
VCC
Vcc
VB
.
Fault
Channel 3
Highside 300 m Ω
Peak&Hold
.
.
.
.
.
.
.
CLKProg
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
Logic
Driver
Diagnosis
DIAG 1
SOUT 3
Channel 2
Highside 300 m Ω
Peak&Hold
DOUT 2
Channel 1
Highside 300 m Ω
Peak&Hold
DOUT 1
Channel 4
Highside/ Lowside
300 mΩ
DOUT 4
Channel 5
Highside/ Lowside
300 mΩ
DOUT 5
Channel 6
Highside/ Lowside
300 mΩ
DOUT 6
SOUT 2
SOUT 1
SOUT 4
SOUT 5
DIAG 5
DIAG 6
Overtemp.
Vcc
GND
.
SCLK
SOUT 6
Vcc
CS
.
SI
GND
SO
.
SPI
Vcc
.
FSIN
Figure 1
Data Sheet
Charge
pump
GND
VCP
Block Diagram
4
Rev. 2.5, 2010-10-11
TLE6288R
Pin Configuration
2
Pin Configuration
2.1
Pin Assignment
Figure 2
Pin Configuration PG-DSO-36-54
2.2
Pin Definitions and Functions
Pin
Symbol
Function
1
SOUT4
Source Output CH 4 (high/low side)
2
DOUT4
Drain Output CH 4 (high/low side)
3
DOUT1
Drain Output CH 1 (high side)
4
SOUT1
Source Output CH 1 (high side)
5
IN4
Control Input Channel 4
6
IN1
Control Input Channel 1
7
DIAG1
Diagnostic Output CH 1
8
DIAG2
Diagnostic Output CH 2
9
DIAG3
Diagnostic Output CH 3
10
DIAG4
Diagnostic Output CH 4
11
DIAG5
Diagnostic Output CH 5
12
DIAG6/Overtemp
Diagnostic Output CH 6 / Overtemp
13
IN2
Control Input Channel 2
14
IN5
Control Input Channel 5
15
SOUT2
Source Output CH 2 (high side)
16
DOUT2
Drain Output CH 2 (high side)
Data Sheet
5
Rev. 2.5, 2010-10-11
TLE6288R
Pin Configuration
Pin
Symbol
Function
17
DOUT5
Drain Output CH 5 (high/low side)
18
SOUT5
Source Output CH 5 (high/low side)
19
SOUT3
Source Output CH 3 (high side)
20
DOUT3
Drain Output CH 3 (high side)
21
VCP
Charge Pump capacitor pin
22
FSIN
All Channels Enable/Disable
23
GND
Logic Ground
24
Fault
General Fault Flag
25
IN3
Control Input Channel 3
26
IN6
Control Input Channel 6
27
Reset
Reset pin (+ Standby Mode)
28
Logic Supply Voltage (5 V)
29
VCC
VDO
30
SO
SPI Serial Data Output
31
CLKProg
Program pin of SPI Clock
32
SCLK
SPI Serial Clock
33
CS
SPI Chip Select
34
SI
SPI Serial Data Input
35
DOUT6
Drain Output CH 6 (high/low side)
36
SOUT6
Source Output CH 6 (high/low side)
2.3
Symbol
Supply pin for digital outputs
Pin Description
Description
DOUT1-3 Drain of the 3 highside channels. These pins must always be connected to the same power (battery)
supply line (VB).
SOUT1-3 Source of the 3 highside channels. Outputs of the highside channels where the load is connected.
DOUT4-6 Drain pins of the 3 configurable channels. In highside configuration they must be connected to the
same voltage as DOUT1-3. In lowside configuration they are the output pins and connected to the
load.
SOUT4-6 Source of the 3 configurable channels. In highside configuration they are the outputs and connected
to the load. In lowside configuration they must be connected with GND.
IN1-6
Parallel input pins for the 6 power outputs. These pins have an internal pull-down structure.
GND
Logic ground pin, the heat slug has to be connected to this potential.
FSIN
Disable pin. If the FSIN pin is in a logic low state, it switches all outputs OFF. The pin has an internal
pull-up structure.
Reset
Reset pin. When the reset is low all channels are off, the internal biasing is deactivated, all internal
registers are cleared and the supply-current consumption is reduced (standby mode). The pin has an
internal pull-up structure.
Fault
General Fault pin. There is a general fault pin (open drain) which shows a high to low transition as
soon as an error is latched into the diagnosis register. When the diagnosis register is cleared this flag
is also reset (high ohmic). This fault indication can be used to generate a μC interrupt.
Data Sheet
6
Rev. 2.5, 2010-10-11
TLE6288R
Pin Configuration
Symbol
Description
CLKProg Programming pin for the SPI Clock signal. This pin can be used to configure the clock signal input of
the SPI. In low state the SPI will read data at the rising clock edge and write data at the falling clock
edge. In high state the SPI will read data at the falling clock edge and write data at the rising clock
edge. The pin has an internal pull-down structure.
DIAG1-5
DIAG6/
Overtemp
Parallel diagnostic pins (push-pull) change state according to the input signal of the corresponding
channel. For further details refer to Chapter 4.3.1
VCP
Pin to connect the external capacitor of the integrated charge pump. Connect a ceramic capacitor with
47 nF between this pin and DOUT3 (VB).
VDO
Supply pin of the push-pull digital output drivers. This pin can be used to vary the high-state output
voltage of the SO pin and the DIAG1-6 pins.
VCC
Logic supply pin. This pin is used to supply the integrated circuitry.
CS
Chip Select of the SPI (active low)
SO
Signal Output of the Serial Peripheral Interface
SI
Signal Input of the Serial Peripheral Interface. The pin has an internal pull-down structure.
SCLK
Clock Input of the Serial Peripheral Interface. The pin has an internal pull-up structure
(if CLKProg = L) or an pull-down structure (if CLKProg = H).
For more details about the SPI see Chapter 5.
Data Sheet
7
Rev. 2.5, 2010-10-11
TLE6288R
General Product Characteristics
3
General Product Characteristics
3.1
Absolute Maximum Ratings
Absolute Maximum Ratings 1)
Tj = -40 ⋅C to +150 ⋅C; all voltages with respect to ground, positive current flowing into pin
(unless otherwise specified)
Pos.
Parameter
Symbol
Limit Values
Unit
PIN / Conditions
Min.
Max.
VB
VB
VB
VCC
VDO
VDSL
-0.3
–
–
20
24
40
V
DOUT1-3
DOUT1-32)
DOUT1-32)
-0.3
7
V
VCC
VDO
–
40
V
DOUT - SOUT
(channel 4 to 6)
Continuous Source Voltage
(highside configuration)
VSH
-9
VB
V
SOUT - GND
(channel 4 to 6)
3.1.4
Input Voltage
VIN
-0.3
VCC + 0.3 V
IN1-6, Reset,
FSIN, CS, SCLK,
SI, CLKProg
3.1.5
Output Voltage
VOUT
-0.3
VCC + 0.3 V
Fault
DIAG1-6
SO
3.1.6
Output Voltage
VCP
–
VB + 10
V
VCP; no voltage
must be applied
Reverse Current (1 ms)
Irev
-4
–
A
between DOUT
and SOUT;
Channel 4 to 6
Tj
Tstg
-40
+150
°C
–
-55
+150
°C
–
VESDb
–
2000
V
–
VESDm
–
250
V
–
Voltages
3.1.1
Power Supply Voltage 1 static
dynamic: 1 min. 25 °C
dynamic: Test cond. see Figure 3
3.1.2
Power Supply Voltage 2
3.1.3
Continuous Drain Source Voltage
(lowside configuration)
Currents
3.1.7
Temperatures
3.1.8
Operating Temperature
3.1.9
Storage Temperature
ESD Susceptibility
3.1.10
ESD (Human Body Model)
C = 100 pF, R = 1.5 kΩ
Applied to all terminals 3 times
3.1.11
ESD (Machine Model)
C = 200 pF, R = 0 Ω
Applied to all terminals 3 times
1) Not subject to production test, specified by design.
2) As long as max. junction temperature Tj is not exceeded.
Attention: Stresses above the ones listed here may cause permanent damage to the device. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Data Sheet
8
Rev. 2.5, 2010-10-11
TLE6288R
General Product Characteristics
Attention: Integrated protection functions are designed to prevent IC destruction under fault conditions
described in the data sheet. Fault conditions are considered as “outside” normal operating
range. Protection functions are not designed for continuous repetitive operation.
40V
10 times
(once/ 30sec)
12V
160ms
350ms
Figure 3
Test Condition
3.2
Thermal Resistance
Pos.
Parameter
Symbol
Limit Values
Min.
Typ.
Unit
Max.
3.2.1
3.2.2
3.2.3
Conditions
–
Junction to Case
1)
Junction to ambient
1)
RthjC
RthjA
1
15.5
K/W
2)
K/W
2) 3)
1) Not subject to production test, specified by design.
2) Channel 1-6 continously turned on, 0.8W power dissipation per channel
3) Specified RthjA value is according to Jedec JESD51-2,-5,-7 at natural convection on FR4 2s2p board ; The Product
(Chip+Package) was simulated on a 76.2 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70μm Cu, 2 x 35μm Cu).
Where applicable a thermal via array under the exposed pad contacted the first inner copper layer.
Further informations can be found in Chapter 7.2
Data Sheet
9
Rev. 2.5, 2010-10-11
TLE6288R
Description
4
Description
4.1
General Functional Description
Channel 1 to 3
•
•
•
•
•
High Side Configuration with Charge Pump
On / off Current Control
Peak & Hold Current Control with fixed off time, values adjustable by SPI
Type of current control can be selected by SPI
Peak Current,Peak Time, Hold Current and Off-Time can be selected by SPI to set average and ripple current
for a given load (refer to Figure 6)
Channel 4 to 6
•
•
Configurable as either High or Low Side switch (by SPI)
On / Off operation
4.1.1
Output Stage Control: Parallel Control and SPI Control
A Boolean operation (either AND or OR) is performed on each of the parallel inputs IN 1 … 6 and respective SPI
data bits, in order to determine the states of the respective outputs. The type of Boolean operation performed is
programmed via the serial interface. Both, parallel inputs and respective SPI databits are high active.
IN 1…6
AND
Output
Driver
OR
Serial Input bits 6 -11 of command
„Channels on / off „
Figure 4
Serial Input Bits 6-11 of Command “Channels on/off”
Each output is independently controlled by an output latch and a common reset line FSIN, which disables all
outputs. A logic high input ‘data bit’ turns the respective output channel ON, a logic low ‘data bit’ turns it OFF.
Table 2
Truth Table
Parallel Input
SPI Bit
Output OR
Output AND
0
0
OFF
OFF
0
1
ON
OFF
1
0
ON
OFF
1
1
ON
ON
Data Sheet
10
Rev. 2.5, 2010-10-11
TLE6288R
Description
4.1.2
•
•
•
Current Regulator: Peak Current Control with Fixed Off-Time
Hold only: When the channel is turned on externally (SPI or parallel input) the current rises to the programmed
hold current level. Then the channel is internally turned off and a timer is started for a fixed off-time (e.g.
200 μs). After this time the channel is internally turned on again until the hold current level is reached again
and so on. This regulation works automatically until the channel is turned of externally.
Peak and hold mode with minimum peak time: When the channel is turned on the current rises to the
programmed peak current level. Then the channel is internally turned off, the current regulator changes to hold
current values and a timer is started for a constant off-time. After this time the channel is internally turned on
again until the hold current value is reached and then again turned off for the fixed off time. This regulation
works automatically until the channel is turned of externally.
Peak and hold mode with programmed peak time: When the channel is turned on the current rises to the
programmed peak current level. Then the channel is internally turned off and a timer is started for a fixed offtime. After this time the channel is internally turned on again until the peak current value is reached and then
again turned off. This works until the programmed peak time is over. Then the current regulator changes to
hold current values and works as described under “hold only”.
Peak Current, Peak Time, Hold Current and fixed Off-Time can be set via SPI.
To avoid regulation disturbances by current transients during switching (e.g. caused by ESD capacitors at the
outputs) the current regulator has a “leading edge blanking” of typical 20 μs in all three regulation modes. After
turning on the DMOS (internally or externally) the current regulation circuit is deactivated for the first 20 μs. This
guarantees that switching of the DMOS itself or charging of small capacitors at the output (e.g. ESD) is not
disturbing the current regulation.
To detect shorted loads or low inductance loads in all three regulation modes a timer is started when a channel is
turned on (tli). If the first rising edge of the load current reaches the programmed current level (peak or hold current
depending on the configured current control mode) within this time a overload fault is reported (see Chapter 7.3).
Figure 5
Data Sheet
Simplified Functional Block Diagram
11
Rev. 2.5, 2010-10-11
TLE6288R
Description
Input Signal
No Regulation
Current defined only by load
Ihd
Hold only
tfo
Ipk
Ihd
Peak & Hold
with min. peak time
tfo
Ipk
tfo
Ihd
Peak and Hold
with set peak time
Figure 6
Data Sheet
tfo
tp
Current Forms of the Different Current Control Modes of Channel 1-3
12
Rev. 2.5, 2010-10-11
TLE6288R
Description
4.2
Protection
The TLE6288R has integrated protection functions1) for overload and short circuit (active current limitation),
overtemperature, ESD at all pins and overvoltage at the power outputs (zener clamping).
Overtemperature Behavior
Each channel has an overtemperature sensor and is individually protected against overtemperature.
As soon as overtemperature occurs the channel is immediately turned off. In this case there are two different
behaviors of the affected channel that can be selected by SPI (for all channels generally):
Autorestart: as long as the input signals of the channel remains on (e.g. parallel input high) the channel turns
automatically on again after cooling down.
Latching: After overtemperature shutdown the channel stays off until the this overtemperature latch is reset by a
new L → H transition of the input signal.
Note: These overtemperature sensors of the channels are only active if the channel is turned on.
An additional overtemperature sensor is located in the logic of the device. It monitors permanently the IC
temperature. As soon as the IC temperature reaches a specified level an overtemperature fault will be indicated.
1) Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet.
Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous
repetitive operation.
Data Sheet
13
Rev. 2.5, 2010-10-11
TLE6288R
Description
4.3
Diagnostic
The TLE6288R has a parallel diagnosis via 6 output pind (DIAG1 - DIAG6) and a serial diagnosis functionallity via
SPI.
4.3.1
Parallel Diagnostic Functions
Parallel diagnostic pins (push-pull) change state according to the input signal of the corresponding channel. As
soon as an error occurs at the corresponding channel (overload and overtemperature is detected in on state and
open load/switch bypass in off state) the DIAG output shows the inverted input signal. An fault is detected only if
it lasts for longer than the fault filter time. The fault information is not latched in a register.
If DIAG6 is configured as Overtemperature Flag: This is a general fault pin which shows a high to low transition
as soon as an overtemperature error occurs for any one of the six channels (for longer than the fault filter time) or
the IC logic. This fault indication can be used to differ between overload and overtemperature errors in one of the
six channels or to detect a general IC overtemperature.
4.3.2
Electrical Characteristics: Diagnostic Functions
Electrical Characteristics: Diagnostic Functions
VCC = 4.5 V to 5.5 V, Tj = -40 ⋅C to +150 ⋅C, VB = 6 V to 16 V, Reset = H, VDO = VCC, all voltages with respect to
ground, positive current flowing into pin (unless otherwise specified)
Pos.
Parameter
Symbol
Limit Values
Min.
Typ.
Max.
Unit
Pin/
Comment
Conditions
4.3.1
Open Load Detection Voltage VDS(OL)
–
5.5
–
V
–
lowside
configuration,
VB = 12 V
4.3.2
Open Load Detection Voltage VDS(OL)
–
4.5
–
V
–
highside
configuration,
VB = 12 V
4.3.3
Output Open Load diagnosis
Current
Id(OL)
-500
-100
-20
μA
–
4.3.4
Fault Filter Time
4.3.5
Switch Bypass Detection
Current
tf(fault)
Id(SB)
4.3.6
Overload Detection Threshold IDd(lim1-3)
(Channel 1 to 3)
4.3.7
Overload / low inductance
load Detection time
(Channel 1 to 3)
4.3.8
Overload Detection Threshold IDd(lim 4-6)
(Channel 4 to 6)
Data Sheet
VB = Vout = 12
V
tli
50
100
200
μs
–
–
–
–
250
μA
–
–
4
–
6
A
–
no regulation
mode
–
–
tfo
μs
see
current
Chapter 7.3 control mode
3
–
6
A
–
14
–
Rev. 2.5, 2010-10-11
TLE6288R
SPI
5
SPI
The SPI is a Serial Peripheral Interface with 4 digital pins and a 16-bit shift register. The SPI is used to configure
and program the device, turn on and off channels and to read detailed diagnostic information.
CS
SCLK
SI
SO
Figure 7
Serial Peripheral Interface
5.1
SPI Signal Description
SPI
CS - Chip Select. The system microcontroller selects the TLE6288R by means of the CS pin. Whenever the pin is
in a logic low state, data can be transferred from the μC and from the TLE6288R to the µC.
•
•
CS = H: Any signals at the SCLK and SI pins are ignored and SO is forced into a high impedance state.
CS = H → L:
– diagnostic information is transferred from the diagnosis register into the SPI shift register
– serial input data can be clocked into the SPI shift register from then on
– SO changes from high impedance state to logic high or low state corresponding to the SO bits
LSB
MSB
internal logic registers
CS
SI
Serial input
data MSB first
16 bit SPI shift register
CS
diagnosis register
LSB
SO
Serial output
(diagnosis)
MSB first
MSB
Figure 8
•
•
CS = L: SPI is working like a shift register. With each clock signal the state of the SI is read into the SPI shiftregister and one diagnosis bit is written out of SO.
CS = L → H:
– transfer of SI bits from SPI shift register into the internal logic registers
– reset of diagnosis register if sent command was valid
To avoid any false clocking the serial clock input pin SCLK should be logic high state (if CLKProg = L; low state if
CLKProg = H) during high to low transition of CS.
SCLK - Serial Clock. The serial clock pin clocks the internal SPI shift register of the TLE6288R. The serial input
(SI) accepts data into the input SPI shift register on the rising edge of SCLK (if CLKProg = L; falling edge if
CLKProg = H) while the serial output (SO) shifts diagnostic information out of the SPI shift register on the falling
Data Sheet
15
Rev. 2.5, 2010-10-11
TLE6288R
SPI
edge (if CLKProg = L; rising edge if CLKProg = H) of serial clock. It is essential that the SCLK pin is in a logic high
state (if CLKProg = L; low state if CLKProg = H) whenever chip select CS makes any transition.
SI - Serial Input. Serial data bits are shifted in at this pin, the most significant bit (MSB) first. SI information is read
in on the rising edge of SCLK (if CLKProg = L; falling edge if CLKProg = H). Input data is latched in the SPI shift
register and then transferred to the internal registers of the logic.
The input data consists of 16 bits, made up of 4 control bits and 12 data bits. The control word is used to program
the device, to operate it in a certain mode as well as providing diagnostic information (see Chapter 5.5).
SO - Serial Output. Diagnostic data bits are shifted out serially at this pin, the most significant bit (MSB) first. SO
is in a high impedance state until the CS pin goes to a logic low state. New diagnostic data will appear at the SO
pin following the falling edge of SCLK (if CLKProg = L; rising edge if CLKProg = H).
5.2
Electrical Characteristics: SPI Timing
Electrical Characteristics: SPI Timing
VCC = 4.5 V to 5.5 V, Tj = -40 ⋅C to +150 ⋅C, VB = 6 V to 16 V, Reset = H, VDO = VCC, all voltages with respect to
ground, positive current flowing into pin (unless otherwise specified)
Pos.
Parameter
Symbol
Limit Values
Min.
Typ.
Max.
Unit
Pin/
Conditions
Comment
5.2.1
Serial Clock Frequency
(depending on SO load)
fSCLK
DC
–
5
MHz –
–
5.2.2
Serial Clock Period (1/fSCLK)
200
–
–
ns
–
–
5.2.3
Serial Clock High Time
50
–
–
ns
–
–
5.2.4
Serial Clock Low Time
50
–
–
ns
–
–
5.2.5
Enable Lead Time
(falling edge of CS to falling
edge of SCLK)
tp(SCLK)
tSCLKH
tSCLKL
tleadL
200
–
–
ns
–
CLKProg = L
tleadH
200
–
–
ns
–
CLKProg = H
Enable Lag Time (rising edge tlagL
of SCLK to rising edge of CS)
200
–
–
ns
–
CLKProg = L
Enable Lag Time (falling edge tlagH
of SCLK to rising edge of CS)
200
–
–
ns
–
CLKProg = H
Enable Lead Time
(falling edge of CS to rising
edge of SCLK)
5.2.6
5.2.7
5.2.8
5.2.9
Data Setup Time (required
time SI to rising of SCLK)
tSUL
20
–
–
ns
–
CLKProg = L
Data Setup Time (required
time SI to falling of SCLK)
tSUH
20
–
–
ns
–
CLKProg = H
Data Hold Time (rising edge of tHL
SCLK to SI)
20
–
–
ns
–
CLKProg = L
Data Hold Time (falling edge of tHH
SCLK to SI)
20
–
–
ns
–
CLKProg = H
Disable Time1)
–
–
200
ns
–
–
Data Sheet
tDIS
16
Rev. 2.5, 2010-10-11
TLE6288R
SPI
Electrical Characteristics: SPI Timing (cont’d)
VCC = 4.5 V to 5.5 V, Tj = -40 ⋅C to +150 ⋅C, VB = 6 V to 16 V, Reset = H, VDO = VCC, all voltages with respect to
ground, positive current flowing into pin (unless otherwise specified)
Pos.
Parameter
Symbol
2)
5.2.10
Transfer Delay Time
(CS high time between two
accesses)
tdt
5.2.11
Data Valid Time1)
CL = 50 pF to 100 pF
CL = 220 pF
tvalid
Limit Values
Min.
Typ.
Max.
200
–
–
–
–
–
–
120
150
Unit
Pin/
Conditions
Comment
ns
–
–
ns
–
–
1) Not subject to production test, specified by design.
2) To get the correct diagnostic information, the transfer delay time has to be extended to the maximum fault filter time
tf(fault)max = 200 μs.
5.3
SPI Diagnostics
As soon as a fault occurs for longer than the fault filter time, the fault information is latched into the diagnosis
register (and the Fault pin will change from high to low state). A new error on the same channel will overwrite the
old error report. Serial data out pin (SO) is in a high impedance state when CS is high. If CS receives a LOW signal,
all diagnosis bits can be shifted out serially. If the sent command was valid (see Note in Chapter 5.5) the rising
edge of CS will reset the diagnosis registers (except the channel OT flag) and restart the fault filter time. In case
of an invalid command the device will ignore the data bits and the diagnosis register will not be reset at the rising
CS edge.
Diagnostic Serial Data Out SO
MSB
15 14
13
12
11
10
9
8
7
Bit0 and Bit1
is always 1
6
5
4
3
2
1
0
LSB
Ch.6
Ch.5
Ch.4
Ch.3
Ch.2
Channel Overtemperature Flag
HH
HL
LH
LL
Figure 9
Ch.1
IC Overtemperature Flag
Normal function
Overload, Shorted Load or Overtemperature
Open Load
Switch Bypassed
Two Bits per Channel Diagnostic Feedback plus two Overtemperature Flags
For Full Diagnosis there are two diagnostic bits per channel configured as shown in Figure 9.
Diagnosis bit 0 and bit 1 are always set to 1.
Data Sheet
17
Rev. 2.5, 2010-10-11
TLE6288R
SPI
Normal function: The bit combination HH indicates that there is no fault condition, i.e. normal function.
Overload, Shorted Load or Overtemperature: HL is set when the current limitation gets active, i.e. there is a
overload, short to supply or overtemperature condition. The second reason for this bit combination is
overtemperature of the corresponding channel.
In current regulation mode HL is also set if the load current reaches the programmed current value in a time shorter
than the fixed off time (tfo). This detection is only performed at the first rising load current edge after a channel is
turned on (for channel 1 to 3). See Chapter 7.3.
Open load: LH is set when open load is detected (in off state of the channel).
Switch Bypassed:
•
•
Short to GND: in lowside configuration LL is set when this condition is detected.
Short to Battery: in highside configuration LL is set when this condition is detected.
Channel Overtemperature Flag: In case of overtemperature in any output channel in on state the
overtemperature Flag in the SPI diagnosis register is set (change bit 3 from 0 to 1). This bit can be used to
distinguish between Overload and Overtemperature (both HL combination) and is reset by switching OFF/ON the
affected channel.
In addition the DIAG6 / Overtemp pin is set low (if configured as Overtemp Flag).
IC Overtemperature Flag: When the IC logic temperature exceeds typ. 170 °C the non-latching IC
Overtemperature Flag will be set in the SPI diagnosis register (change bit 2 from 0 to 1).
In addition the DIAG6 / Overtemp pin is set low (if configured as Overtemp. Flag).
5.4
SPI Commands, Values and Parameters
The 16-bit SPI is used to program different IC functions and values, turn on and off the channels and to get detailed
diagnosis information. Therefore 4 command bits and 12 data bits are used.
CS
4 Bits
Command
SI
SO
12 Bits
Da ta
Diagnosis ( Ch. 1 to 6)
+ 2 Temp. Flags
SI command : 4 Command Bits program
the operation mode of Channels 1 to 6.
12 Data Bits configure the device and
give the input information (on or off) for
Channel 1 to 6.
SO diagnosis 16 bit diagnosis information
(two bit per channel) of channels 1 to 6 plus
two Overtemperature Flags
Figure 10
Data Sheet
18
Rev. 2.5, 2010-10-11
TLE6288R
SPI
The following parameters and functional behavior can be programmed by SPI:
•
•
•
•
•
•
•
•
•
•
Current regulation mode (mode): for each of the 3 highside channels individually the operation mode can be
set.
– “no current regulation”
– current regulation “hold only”
– current regulation “peak & hold with minimum peak time”
– current regulation “peak & hold with programmed peak time”
Peak Current (Ipk): for each of the 3 highside channels individually the peak current value for P&H current
regulation can be programmed. The current range is 1.2 A to 3.6 A.
Fixed off time of the current regulator (tfo): for each of the 3 highside channels (Ch1 to Ch3) individually the
fixed off time for all modes with current regulation can be programmed from 100 μs to 400 μs.
Hold current (Ihd): for each of the 3 highside channels (Ch1 to Ch3) individually the hold current value for P&H
and hold only current regulation can be programmed. The current range is 0.7 A to 2.0 A.
Peak time (tp): for each of the 3 highside channels (Ch1 to Ch3) individually the peak time value for P&H
current regulation can be programmed. The time range is 0.8 ms to 3.6 ms.
Highside/Lowside configuration (H/L): Each of the 3 configurable channels (Ch4 to Ch6) can be
programmed for use as Highside switch or Lowside switch.
Open load and switch bypassed detection activated or deactivated (OL+SB): For each of the 3
configurable channels (Ch4 to Ch6) the open load and switch bypassed diagnosis can be deactivated. In
lowside configuration the open load and the short to GND detection can be deactivated, in highside
configuration the open load and short to battery detection.
Boolean operation (OR/AND): For all channels generally the Boolean operation of the parallel input signal
and the SPI bit of the corresponding channel can be defined.
Overtemperature behavior (R/L): The overtemperature behavior of the channels can be programmed by SPI.
Autorestart or latching overtemperature shutdown can be selected (for all channels the same behavior).
DIAG6 or overtemperature flag (D/F): With this SPI bit the function of the DIAG6 / Overtemp pin is defined.
This output can work as diagnosis output of channel 6 or as Overtemperature Flag.
5.5
SPI Commands
Table 3
Command Table
Command
MSB 14
13
12
11
10
9
Set all to Default
X
X
X
8
7
X
X
6
5
X
X
4
3
X
X
2
1
LSB
X
X
X
1
0
0
0
Config. Regulator 1 1
0
0
1
Mode
Config. Regulator 2 1
0
1
0
Mode
Config. Regulator 3 1
0
1
1
Mode
Config. Ch1 - Ch6
1
1
0
0
Ch6 Ch6 Ch5 Ch5 Ch4 Ch4 all
all DIAG
H/L OL+ H/L OL+ H/L OL+ OR/ R/L 6D/F
SB
SB
SB AND
X
X
X
Channels on/off
1
1
0
1
Ch6 Ch5 Ch4 Ch3 Ch2 Ch1 X
X
X
X
X
X
Diagnosis only
1
1
1
1
X
X
X
X
X
X
Data Sheet
X
Ipk
Ipk
Ipk
X
19
X
tfo
tfo
tfo
X
X
Ihd
Ihd
Ihd
X
tp
tp
tp
X
X
X
Rev. 2.5, 2010-10-11
TLE6288R
SPI
Legend of SPI Command Table
•
•
•
•
•
•
•
•
•
•
•
Mode: Operation mode of the current regulator:
– no regulation
– hold only
– peak & hold with minimum peak time
– peak & hold with programmed peak time
Ipk: Peak current values 1.2 A … 3.6 A
Ihd: Hold current values 0.7 A … 2 A
tp: Peak time value 0.8 ms … 3.6 ms
tfo: Fixed off time value 100 μs … 400 μs
H/L: Channel 4 to 6 in highside or lowside configuration
OL+SB: open load detection and switch bypassed detection activated or deactivated
OR/AND: Boolean Operation (parallel input and corresponding SPI Bit)
R/L: Autorestart or Latching overtemperature behaviour
D/F: DIAG6/Overtemp pin set as Diagnosis output of channel 6 or as Overtemperature Flag
Ch1-Ch6: On/Off information of the output drivers (high active)
Command Description
Config. Regulator 1-3: With this command the values for the current regulation and the functional mode of the
channel is written into the internal logic registers.
Config. Ch1 to Ch6: This command writes the configuration data of the 3 configurable channels (4-6) and sets
the Boolean operation and overtemperature behavior of all channels. It also sets the DIAG6/Overtemp. pin to
Diagnosis of channel 6 or Overtemperature Flag.
Set all to default: This command sets all internal logic registers back to default settings.
Diagnosis only: When this command is sent the 12 data bits are ignored. The internal logic registers are not
changed.
Channels on/off: With this command the SPI bits for the ON/OFF information of the 6 Channels are set.
Note: Specified control words (valid commands) are executed and the diagnosis register is reset after the rising
CS edge.
Not specified control words are not executed (cause no function) and the diagnosis register is not reset after
the CS = L → H signal.
Data Sheet
20
Rev. 2.5, 2010-10-11
TLE6288R
SPI
5.6
Bit Assignment and Default Settings for Internal Logic Registers
Mode
00
no current regulation
01
hold only
10
P&H minimum peak time
11
P&H with programmed times
Peak Current (Ipk)
1.2 A
1.8 A
2.4 A
3.6 A
2 Bits
00
01
10
11
Hold Current (Ihd)
0.7 A
1.0 A
1.4 A
2.0 A
2 Bits
00
01
10
11
Fixed off Time (tfo)
100 μs
200 μs
300 μs
400 μs
2 Bits
00
01
10
11
Peak Time (tp)
0.8 ms
1.2 ms
1.6 ms
2.0 ms
2.4 ms
2.8 ms
3.2 ms
3.6 ms
3 Bits
000
001
010
011
100
101
110
111
Boolean operation
OR
AND
1 Bit
0
1
Overtemp. behavior
Restart
Latch
1 Bit
0
1
Diag6 / Overtemp
Diag6
Overtemp. Flag
1 Bit
0
1
Highside / Lowside
Highside
Lowside
1 Bit
0
1
Open Load & SB (4-6)
Yes
No
1 Bit
0
1
Channels on / off
off
on
1 Bit
0
1
Default Settings are in bold print.
Data Sheet
21
Rev. 2.5, 2010-10-11
TLE6288R
SPI
5.7
SPI Timing Diagrams
CS
0.7Vcc
tdt
0.2 Vcc
tlagL
tSCKH
0.7Vcc
SCLK
tleadL
tSUL
0.2Vcc
tSCKL
tHL
0.7Vcc
SI
0.2Vcc
Figure 11
Input Timing Diagram (CLKProg = L)
CS
0.2 Vcc
SCLK
0.2 Vcc
tvalid
tDis
0.7 Vcc
SO
SO
0.2 Vcc
SO
0.7 Vcc
0.2 Vcc
Figure 12
SO Valid Time Waveforms and Enable and Disable Time Waveforms (CLKProg = L)
CS
SCLK
4 control bit
SI
Co
12 data bit
n t
r o l
word
11
14
13
12
11
10
9
8
7
6
9
8
7
6
5
4
3
2
1
4
3
2
1
MSB
SO
Figure 13
Data Sheet
15
0
LSB
10
5
0
Serial Interface
22
Rev. 2.5, 2010-10-11
TLE6288R
SPI
CS
0.7Vcc
tdt
0.2 Vcc
tlagH
tSCKH
tleadH
0.7Vcc
0.2Vcc
SCLK
tSCKL
tSUH
tHH
0.7Vcc
SI
0.2Vcc
Figure 14
Input Timing Diagram (CLKProg = H)
0.7 V cc
CS
SCLK
0.2 V cc
t valid
t Dis
0.7 V cc
SO
SO
0.2 V cc
SO
0.7 V cc
0.2 V cc
Figure 15
SO Valid Time Waveforms and Enable and Disable Time Waveforms (CLKProg = H)
CS
SCLK
4 control bit
SI
Co
n t
12 data bit
r o l
word
11
10
9
8
7
6
5
4
3
2
1
MSB
SO
Figure 16
Data Sheet
15
0
LSB
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Serial Interface
23
Rev. 2.5, 2010-10-11
TLE6288R
Electrical Characteristics Input / Output Pins
6
Electrical Characteristics Input / Output Pins
6.1
Power Supply, Reset
Electrical Characteristics: Power Supply, Reset
VCC = 4.5 V to 5.5 V, Tj = -40 ⋅C to +150 ⋅C, VB = 6 V to 16 V, Reset = H, VDO = VCC, all voltages with respect to
ground, positive current flowing into pin (unless otherwise specified)
Pos.
Parameter
Symbol
Min.
Typ.
Max.
6.1.1
Power Supply Current 1
–
–
6.1.2
Power Supply Current 2
–
6.1.3
Power Supply Current in
Standby Mode
IB
ICC
ICC + Ib
–
tReset,min
twakeup
50
–
–
μs
–
–
–
–
5
ms
–
CCP = 10 nF
6.1.4
Minimum Reset Duration
6.1.5
Wake-up time after reset
6.2
Limit Values
Unit
Pin/
Conditions
Comment
10
mA
DOUT1-3
Ch1-Ch6: Off
–
10
mA
VCC
–
–
50
μA
DOUT1-3, Reset = L
VCC
Power Outputs
Electrical Characteristics: Power Outputs
VCC = 4.5 V to 5.5 V, Tj = -40 ⋅C to +150 ⋅C, VB = 6 V to 16 V, Reset = H, VDO = VCC, all voltages with respect to
ground, positive current flowing into pin (unless otherwise specified)
Pos.
Parameter
Symbol
Limit Values
Min.
Typ.
Max.
Unit
Pin/
Conditions
Comment
6.2.1
On Resistance
RDS(ON)
–
–
350
mΩ
DOUTx SOUTx
6.2.2
Forward Voltage Revers
Diode
VRDf
–
–
2
V
SOUTx DOUTx
ID = 2.4 A
VB = 10 V
ID = -4 A
Tj = 150 °C
6.2.3
Peak Current range
Ipk
–
1.2 …
3.6
–
A
–
–
6.2.4
Peak Current accuracy
Ipka
–
–
±15
±20
%
%
–
Tj = 25, 150 °C
Tj = -40 °C
6.2.5
Hold Current range
–
0.7 … 2 –
A
–
–
6.2.6
Hold Current accuracy
Ihd
Ihda
–
–
±15
±20
%
%
–
Tj = 25, 150 °C
Tj = -40 °C
6.2.7
Peak time range
tp
–
0.8 …
3.6
–
ms
–
–
6.2.8
Peak time accuracy
–
–
±20
%
–
–
6.2.9
Fixed off Time range
tpa
tfo
–
100 …
400
–
μs
–
–
6.2.10
Fixed off Time accuracy
–
–
±30
%
–
100 μs
6.2.11
Fixed off Time accuracy
tfoa
tfoa
–
–
±20
%
–
200 μs 400 μs
6.2.12
Output ON Delay time1
–
–
10
μs
–
see Figure 17
6.2.13
Output ON Rise time1
tdON
tr
–
–
10
μs
–
see Figure 17
Data Sheet
24
Rev. 2.5, 2010-10-11
TLE6288R
Electrical Characteristics Input / Output Pins
Electrical Characteristics: Power Outputs (cont’d)
VCC = 4.5 V to 5.5 V, Tj = -40 ⋅C to +150 ⋅C, VB = 6 V to 16 V, Reset = H, VDO = VCC, all voltages with respect to
ground, positive current flowing into pin (unless otherwise specified)
Pos.
Parameter
Symbol
Limit Values
Min.
Typ.
Max.
Unit
Pin/
Conditions
Comment
6.2.14
Output OFF Delay time
tdOFF
–
–
20
μs
–
HS- Mode
LS- Mode
see Figure 17
6.2.15
Output OFF Fall time
tf
–
–
10
μs
–
see Figure 17
6.2.16
Leakage Current
–
–
–
10
μA
–
Reset = L
6.2.17
Leak Current in OFF
(highside configuration)
Iloff
–
–
-250
μA
SOUT1-6
–
6.2.18
Leak Current in OFF
(lowside configuration)
Iloff
–
–
500
μA
DOUT4-6
–
6.2.19
Output Clamp Voltage
(highside configuration)
Vclh
-19
-14
-9
V
SOUT1-6
Refers to GND
level
6.2.20
Output Clamp Voltage
(lowside configuration)
Vcll
40
–
55
V
DOUT4-6
Refers to GND
level
6.2.21
Current limitation
(Channel 1 to 3)
IDlim1-3
4
–
6
A
–
–
6.2.22
Current limitation
(Channel 4 to 6)
IDlim4-6
3
–
6
A
–
–
6.2.23
IC Overtemp. Warning1)
Hysteresis
Tot
Thys
160
–
–
10
180
–
°C
°C
–
–
1) Not subject to production test, specified by design.
6.3
Digital Inputs
Electrical Characteristics: Digital Inputs
VCC = 4.5 V to 5.5 V, Tj = -40 ⋅C to +150 ⋅C, VB = 6 V to 16 V, Reset = H, VDO = VCC, all voltages with respect to
ground, positive current flowing into pin (unless otherwise specified)
Pos.
Parameter
Symbol
Limit Values
Min.
Typ.
Max.
Unit
Pin/
Conditions
Comment
6.3.1
Input Low Voltage
VINL
–
–
1
V
all digit.
inputs
–
6.3.2
Input High Voltage
VINH
2
–
–
V
all digit.
inputs
–
6.3.3
Input Voltage Hysteresis
VINHys
–
100
–
mV
all digit.
inputs
–
6.3.4
Input pull-down current
Ipd
20
50
100
μA
IN1-6;
CLKProg
VIN = 5 V
6.3.5
Input pull-up current
Ipu
-100
-50
-20
μA
Reset;
FSIN
VIN = GND
Data Sheet
25
Rev. 2.5, 2010-10-11
TLE6288R
Electrical Characteristics Input / Output Pins
Electrical Characteristics: Digital Inputs (cont’d)
VCC = 4.5 V to 5.5 V, Tj = -40 ⋅C to +150 ⋅C, VB = 6 V to 16 V, Reset = H, VDO = VCC, all voltages with respect to
ground, positive current flowing into pin (unless otherwise specified)
Pos.
Parameter
Symbol
Limit Values
Min.
Typ.
Max.
Unit
Pin/
Conditions
Comment
6.3.6
SPI Input pull-down current
Ipd
10
20
50
μA
SI, SCLK VIN = 5 V
(CLKProg
= H)
6.3.7
SPI Input pull-up current
Ipu
-50
-20
-10
μA
CS, SCLK VIN = GND
(CLKProg
= L)
6.4
Digital Outputs
Electrical Characteristics: Digital Outputs
VCC = 4.5 V to 5.5 V, Tj = -40 ⋅C to +150 ⋅C, VB = 6 V to 16 V, Reset = H, VDO = VCC, all voltages with respect to
ground, positive current flowing into pin (unless otherwise specified)
Pos.
Parameter
Symbol
Limit Values
Min.
Typ.
Max.
Unit
Pin/
Conditions
Comment
6.4.1
SO Low State Output Voltage VSOL
–
–
0.4
V
SO
6.4.2
SO High State Output Voltage VSOH
VDO 0.4 V
–
–
V
SO
ISOL = 2.5 mA
ISOH = -2 mA
6.4.3
DIAG Low State Output
Voltage
VDIAGL
–
–
0.4
V
DIAG1-6
IDIAGL = 50 μA
6.4.4
DIAG High State Output
Voltage
VDIAGH
VDO 0.4 V
–
–
V
DIAG1-6
IDIAGH =
6.4.5
Fault Low Output Voltage
–
–
0.4
V
Fault
Iout = 1 mA
6.4.6
Fault Output leak Current
Vol
Ioh
–
–
1
μA
Fault
Output: OFF
V(fault) = 5 V
-50 μA
Input Voltage
tdON
tdOFF
70%
Output Voltage
(Highside configuration)
30%
tf
tr
Figure 17
Data Sheet
Turn on/off Timings with Resistive Load
26
Rev. 2.5, 2010-10-11
TLE6288R
Application Information
7
Application Information
7.1
Zthjc Diagram Junction - Case for Single channel operation
Zth(D, Pulse width) [K/W]
10
1
Dutycycle D
0,1
0,5
0,2
0,1
0,05
0,02
0,01
0,01
0,000001
0,00001
0,0001
0,001
0,01
0,1
Pulse width [s]
Figure 18
•
Zthjc Diagram
Conditions for Figure 18
– Results based on FEM Simulations
– Tcase = 125 °C
– Single Channel operation, 0.8W power dissipation
7.2
Thermal Application Information
All thermal resistance values in this document are data from FEM (Finite Element Modelling). The boundary
conditions are chosen according to the JESD51 standard. Therefore, all values can be viewed as reliable and
reproducible.
The high effective thermal conductivity test PCB (2s2p) gives a near best case thermal performance value.
compared to the single layer low effective thermal conductivity PCB (1s). It should be emphasized that values
measured/simulated with these test boards cannot be used to directly predict any particular system application
performance.
In real applications, the RthjA can be influenced by the environment and PCB conditions. Thermal vias, application
specific multi layer PCBs and a direct thermal connection to the ECU metal-case are often used to improve the
thermal impedance RthjA.
Data Sheet
27
Rev. 2.5, 2010-10-11
TLE6288R
Application Information
Figure 19
FE Model of the JEDEC 2s2p PCB
Figure 20
Thermal via layout
Figure 19 showes the Product TLE6288R on the 2s2p board used to specify the typical RthjA value in Chapter 3.2.
In Figure 20, the thermal via layout according to JESD51-5 is shown.
Data Sheet
28
Rev. 2.5, 2010-10-11
TLE6288R
Application Information
7.3
Overload/Low Inductance Load Detection in Current Regulation Mode
Input Signal
Ipk / Ihd
Load Current
normal condition
tli
tfo
Overload / low inductance load detection
Ipk / Ihd
Load Current
low-inductance load
tli
tfo
Figure 21
Data Sheet
29
Rev. 2.5, 2010-10-11
TLE6288R
Package Outlines
Package Outlines
0.65
0.25 +0.13
6.3
0.1 C
(Mold)
5˚ ±3˚
0.25
2.8
1.3
15.74 ±0.1
(Heatslug)
B
+0.07
-0.02
11 ±0.15 1)
3.5 MAX.
0 +0.1
1.1 ±0.1
3.25 ±0.1
8
Heatslug
0.95 ±0.15
36x
0.25 M A B C
14.2 ±0.3
0.25 B
19
1
18
10
36
5.9 ±0.1
(Metal)
19
3.2 ±0.1
(Metal)
Bottom View
36
Index Marking
1 x 45˚
15.9 ±0.1 1)
(Mold)
1)
A
13.7 -0.2
(Metal)
1
Heatslug
Does not include plastic or metal protrusion of 0.15 max. per side
GPS09181
Figure 22
PG-DSO-36-54 (Plastic Dual Small Outline Package)
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant with
government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e
Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
You can find all of our packages, sorts of packing and others in our
Infineon Internet Page “Products”: http://www.infineon.com/products.
Data Sheet
30
Dimensions in mm
Rev. 2.5, 2010-10-11
TLE6288R
Revision History
9
Revision
Revision History
Date
Changes
2.2
2004-03-25 Preliminary Datasheet TLE6288R Vp2.2
2.3
2006-05-03 Formal changes, Thermal information added, Spec. values not changed
2.4
2007-08-08 RoHS-compliant version of the TLE6288R
Page 3:
“AEC qualified” and “RoHS” logo added, “Green Product (RoHS compliant)” and “AEC
qualified” statement added to feature list, package names changed to RoHS
compliant versions, package pictures updated
Page 30:
Package names changed to RoHS compliant versions, “Green Product” description
added
Revision History updated
Legal Disclaimer updated
2.5
2010-10-11 Updated package type
Data Sheet
31
Rev. 2.5, 2010-10-11
Edition 2010-10-11
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2010 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.