NCP373 D

NCP373
Overvoltage Up to +30 V
and Down to -30 V with
Load Switch Function
NCP373 is an over−voltage and over−current protection device.
From IN to VBUS , the part acts as a load switch protection, with
programmable current regulation. The current protection is externally
adjustable, up to 400 mA or 1300 mA, depending on selected version.
Additional voltage protection is available, from VBUS to IN. Due to
built−in low RDS(on) NMOS FET, the host system is protected against
positive and negative voltages up to ±28 V.
The embedded over−current and over−voltage protection allow the
device to sustain extreme conditions from short circuit on USB
connector, or defective WA or USB port.
Because to the NCP373 using internal NMOS, the system cost and
the PCB area of the application board are minimized.
NCP373 provides a negative going flag (FLAG) output, which
alerts the system that a fault has occurred.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Adjustable Over−current
Over−voltage Protection Up to 28 V and Down to −28 V
Logic pins EN and DIR
Thermal Shutdown
On−chip low RDS(on) NMOS Transistors
Over−voltage Lockout (OVLO)
Soft−start
Real Shutdown Mode
Alert FLAG Output
Compliance to IEC61000−4−2 (Level 4)
8 kV (Contact)
15 kV (Air)
ESD Ratings: Machine Model = B
Human Body Model = 2
12 Leads LLGA 3X3 mm Package
These are Pb−Free Devices
http://onsemi.com
MARKING
DIAGRAM
1
XXXX
ALYWG
G
12 PIN LLGA
MU SUFFIX
CASE 513AK
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W
= Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
VBUS
1
12
NC
VBUS
2
11
IN
GND
3
10
FLAG
RES1
4
RES2
RES3
NCP373
9
DIR
5
8
EN
6
7
Ilim
(Top View)
ORDERING INFORMATION
See detailed ordering, marking and shipping information in the
package dimensions section on page 9 of this data sheet.
Typical Applications
•
•
•
•
USB ports
Tablets
Set Top Box
Cell Phones
© Semiconductor Components Industries, LLC, 2013
May, 2013 − Rev. 2
1
Publication Order Number:
NCP373/D
NCP373
NCP373
POWER SUPPLY
IN
4.7 mF
1
LDO 3.3V
IN
OUT
VBUS
VBUS
GND
RES
RES
RES
IN
FLAG
DIR
REV
Ilim
1 mF
1 mF
3
VCC
GND
USB HOST CONTROLLER
2
STATUS
EN
SYS
SYSTEM
CRTL_IN[x:0]
DATA_IN[x:0]
CRTL[x:0]
DATA[x:0]
1
VBUS(sense)
D+
D−
GND
5
2
3
4
VBUS
D+
D−
GND
USB PORT
10
10
USB PORT
12
11
CRTL_OUT[x:0]
DATA_OUT[x:0]
VCC
12
CRTL[x:0] 11
DATA[x:0]
GND
VBUS(sense)
D+
D−
GND
GND
5
2
3
4
USB TRANSCEIVER
USB TRANSCEIVER
GND
VBUS
D+
D−
GND
VCC
1
120 mF
Upstream USB Port
Downstream USB Port
Figure 1. Typical Host Application Circuit
D+
D−
D+
PHY (Transceiver)
Ctr
D−
LDO
Vbus
VBUS
D+
D−
GND
USB PORT
VBUS
D+
D−
GND
NCP373
Wall Adapter
1mF1
10k
VBUS
VBUS
IN
GND /FLAG
RES
/DIR
RES
/EN
RES
Ilim
CCCV CHARGER
FLAG
DIR
REV
LI+BATTERY
SYSTEM
Wall Adapter
Rlimit 1
FLAG
4.7mF1
DIR
REV
Ctr
GND
Figure 2. Typical Portable Application Circuit
http://onsemi.com
2
NCP373
FUNCTIONAL BLOCK DIAGRAM
Exposed pad − Pad 1
IN– Pin11
VBUS– Pins1and2
Gate 2 Driver : Negative
voltage and reverse
current protection
Gate 1 Driver : Positve
voltage
OCP block
ILIM– Pin7
Core
negative
voltage
protection
LDO
VREF
Charge
Pump
UVLO
OVLO
RES1– Pin4
5.5V
Control
logic and
Timer
EN block
Trim
RES2 – Pin5
RES3 – Pin6
Thermal
Shutdown
/EN– Pin8
Not Connected
– Pin10
/DIR– Pin9
GND– Pin3
FLAG– Pin10
Figure 3. Functional Block Diagram
PIN FUNCTION DESCRIPTION
Pin
Pin Name
Type
Description
1,2
VBUS
POWER
VBUS voltage pins: must be hardwired together on the PCB.
These pins are connected to the VBUS connector, and are protected against positive and
negative overvoltage events.
A 1 mF low ESR ceramic capacitor, or larger, must be connected between these pins and GND.
3
GND
POWER
Ground
4
RES1
INPUT
Reserved pin. Must be connected to GND potential and used for IC test.
5
RES2
INPUT
Reserved pin. Must be connected to GND potential and used for IC test.
6
RES3
INPUT
Reserved pin. Must be connected to GND potential and used for IC test.
7
Ilim
OUTPUT
Current Limit Pin. This pin provides the reference, based on the internal band−gap voltage
reference, to limit the over current, across internal N−MOSFET. A 0.1% tolerance resistor shall
be used to get the highest accuracy of the Over Current Limit.
http://onsemi.com
3
NCP373
PIN FUNCTION DESCRIPTION
Pin
Pin Name
Type
Description
8
EN
INPUT
Enable Pin. In combination with DIR, the internal NMOSes are turned on if Battery is applied on
the IN pins. (See logic table)
In enable mode, the internal Over−Current protection is activated from IN to VBUS. When
enable mode is disabled, the NCP373 current consumption, into IN pin, is drastically decreased
to limit current leakage of the self powered devices.
9
DIR
INPUT
Direct Mode pin. This pin can be used, in combination with Enable pin, for the front end
protection applications like wireless devices. In this case, the part can be used as +/− OVP only.
See logic table.
10
FLAG
OUTPUT
Fault indication pin.
This pin allows an external system to detect fault condition.
The FLAG pin goes low when input voltage exceeds OVLO threshold or drops below UVLO
threshold (charging mode), charge current from IN to VBus exceeds current limit or internal
temperature exceeds thermal shutdown limit.
Since the FLAG pin is open drain functionality, an external pull up resistor to VBat must be
added (10 kW minimum value).
11
IN
POWER
IN pin. In Front end application this pin is connected to CCCV device input or PMIC input.
In host application, this pin is connected to upstream DCDC. This pin is used as power supply of
the core and current from IN to VBUS is then limited to the external
12
NC
NA
13
PAD1
POWER
Not internally connected. Can be connected to any potential.
Drain connection of the back to back MOSFET’s. This exposed pad mustn’t be connected to any
other potential and must be used for thermal dissipation of the internal MOSFETs.
MAXIMUM RATINGS
Rating
Minimum Voltage (VBus to GND)
Minimum Voltage (All others to GND)
Maximum Voltage (VBus to GND)
Symbol
Value
Unit
VminVBUS
−30
V
Vmin
−0.3
V
VmaxVBUS
30
V
Maximum Voltage (IN to GND)
VmaxIN
10
V
Maximum Voltage (VBus to Vin)
VmaxVBUS−VIN
±30
V
Vmax
7
V
500
500
mA
mA
2
1.5
A
A
RqJA
200
°C/W
Operating Ambient Temperature Range
TA
−40 to +85
°C
Storage Temperature Range
Tstg
−65 to +150
°C
Maximum Voltage (All others to GND)
Maximum DC current
NCP373MU04TXG
Charge Mode
Vbus Mode
NCP373MU13TXG
Charge Mode
Vbus Mode
Iin
Thermal Resistance, Junction−to−Air, (Note 1)
Junction Operating temperature
TJ
150
°C
ESD Withstand Voltage (IEC 61000−4−2)
Human Body Model (HBM), Model = 2, (Note 2)
Machine Model (MM) Model = B, (Note 3)
Vesd
15 kV air, 8 kV contact
2000 V
200 V
kV
V
V
Moisture Sensitivity
MSL
Level 1
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The RqJA is highly dependent on the PCB heat sink area (connected to PAD1). See PCB recommendation paragraph.
2. Human Body Model, 100 pF discharged through a 1.5 kW resistor following specification JESD22/A114.
3. Machine Model, 200 pF discharged through all pins following specification JESD22/A115.
http://onsemi.com
4
NCP373
ELECTRICAL CHARACTERISTICS Min / Max limits values (−40°C < TA < +85°C) and IN = +5 V (Unless otherwise noted). Typical
values are TA = +25°C
Characteristics
Symbols
Input Voltage Range
Vin
Vbus Voltage Range
Vvbus
Conditions
Min
Typ
Max
Unit
2.5
5.5
V
All modes
−28
28
V
All modes
IN = 5 V
−23
Under Voltage Lockout Threshold
UVLO
Vbus falls down UVLO threshold
Disable, Charge mode and Enhance
Modes
2.6
2.7
2.8
V
Under Voltage Lockout Hysteresis
UVLOhyst
Vbus rises up UVLO threshold +
UVLOhyst
45
60
75
mV
Over voltage Lockout threshold
Over Voltage Lockout Hysteresis
Vbus versus IN Resistance
IN versus Vbus Resistance
Quiescent Current
Standby Current
Current limit
FLAG Output Low Voltage
FLAG Leakage Current
DIR Voltage High
DIR Voltage Low
DIR Leakage current
OVLO
Vbus rises up OVLO threshold
5.6
5.77
5.9
V
OVLOhyst
Vbus falls down to OVLO – OVLOhyst
45
65
90
mV
RDson
Vbus = 5 V, or IN = 5 V Direct Mode,
Load
connected to Vout
NCP373MU04TXG
NCP373MU13TXG
200
130
300
220
IddIN
No load. Vbus mode, Vin= 5 V
200
315
mA
IddSTD
No load, IN = 5 V. Standby mode, No
Vbus
0.02
1
mA
IOCP
IN = 5 V, Load on Vbus,
Vbus mode
RILIM = 0 W
NCP373MU04TXG
NCP373MU13TXG
Volflag
Fault mode
Sink 1 mA on FLAG pin
FLAGleak
FLAG level = 5.5 V
Vih
EN Voltage Low
Vol
Thermal Shutdown Hysteresis
330
1100
400
1300
470
1500
400
1
nA
0.4
DIR = 5.5 V
300
V
0.4
EN = 5.5 V
V
nA
1.2
ENleak
mV
V
Vol
Vih
Thermal Shutdown temperature
mA
1.2
DIRleak
EN Voltage High
EN Leakage current
mW
V
300
nA
TSD
150
°C
TSDHYST
30
°C
TIMINGS
Vbus MODE
TonVbus
IN ≥ 2.5 V, from EN = 1.2 to 0.4 to
Vbus ≥ 0.3 V
Vbus Mode
0.6
1.2
1.8
ms
Tstartvbus
From IN ≥ 0.3 V FLAG = 1.2 V, Vbus
Mode
0.6
1.2
1.8
ms
Rearming Delay
tRRD
IN > .2.5 V, Rin = 1 W Vbus Mode, after
fault
15
30
45
ms
Over Current Regulation Time
treg
IN > 2.6, Vbus > 0.3 V Vbus Mode
0.5
1.2
1.8
ms
OCP delay time
tOCP
From I Vbus > Ilim, 1 A/1 ms
Start Up Delay
FLAG going up Delay
NOTE:
Electrical parameters are guaranteed by correlation across the full range of temperature.
http://onsemi.com
5
5
ms
NCP373
ELECTRICAL CHARACTERISTICS Min / Max limits values (−40°C < TA < +85°C) and IN = +5 V (Unless otherwise noted). Typical
values are TA = +25°C
Characteristics
Symbols
Conditions
Min
Typ
Max
Unit
TVbusDIS
From EN = 0.4 V to 1.2 V, to Vbus <
0.3 V. IN = 5 V
2.5
toff
From IN > OVLO to Vbus ≤ 0.3 V
Vin increasing from 5 V to 8 V at 3 V/ms
1.5
5
ms
ton
From Vbus > UVLO to IN = 0.3 V ,
charging mode
15
30
45
ms
tstart
From IN>0.3V to FLAG = 1.2 V
15
30
45
ms
toff
From Vbus > OVLO to IN ≤ 0.3 V
Vin increasing from 5 V to 8V at 3V/ms
1.5
5
ms
Alert delay
tstop
From Vbus > OVLO to FLAG ≤ 0.4 V
See Figures 3and 9
Vin increasing from 5 V to 8 V at 3 V/ms
1.5
ms
Disable time
tdis
EN = 1.2 V, From DIR = 0.4 to 1.2 V to
IN ≤ 0.3 V
2.5
ms
TIMINGS
Vbus MODE
Vbus Disable time
Turn off delay
ms
CHARGING MODE
Start Up Delay
FLAG going up Delay
Turn off delay
NOTE:
Electrical parameters are guaranteed by correlation across the full range of temperature.
TYPICAL OPERATING CHARACTERISTICS
Operation
the output remains disabled until the input voltage exceeds
OVLO (Vbus pin).
The OVLO comparator is available in all modes.
Additional OVLO thresholds ranging from OVLO can be
manufactured. Please contact your ON Semiconductor
representative for further information.
FLAG output is tied to low until Vin is higher than OVLO.
This circuit has a built−in hysteresis to provide noise
immunity to transient conditions.
The NCP373acts as an over−voltage in charge mode,
when wall adapter or Vbus cable is connected to Vbus pin
of the device. The downstream system (transceiver, CCCV
charger..) are protected up to +30 V if charging voltage
exceeds OVLO threshold (5.77 V). Thanks to a back to back
architecture, the Vbus pin is also protected against reverse
polarity connection, coming from wrong USB cables. This
negative protection acts down to −30 V.
In disable mode (EN = 1, DIR = 1), there is no current
consumption on IN pin and MSOFETs are turned off (Vbus
cable disconnected)
The NCP373 provides over−current from IN to Vbus by
selecting Vbus mode.
To active Vbus mode (USB port on), the EN pin must be
tied low. In this case, MOSFET are turned on and current is
measure in the branch. If the sinking current on the Vbus pin
is above the programmed current on Ilim pin (can be
programmed up to 400 mA), the Vbus current is regulated
around Iocp during treg time. If the overload is present at the
end of this timer, the MOSFET are turned off and automatic
rearming cycle is activated. With Treg/Trrd cycle until
overload is present.
Over−Current protection (OCP)
This device integrates over current protection function,
from IN to Vbus port (400 mA version and 1300 mA
version).
That means the current across the internal NMOS is
regulated when the value, set by external Rlim resistor,
exceeds Ilimit during an internal timer.
An internal resistor is placed in series with the pin
allowing to have a maximum OCP value when I lim pin is
directly connected to GND.
By adding external resistors in series with I lim and GND,
the OCP value is decreased. The Rlim tolerance is important
to keep a good accuracy. So a value between 0.1% and 1%
won’t have an impact on the OCP accuracy. Nevertheless,
the higher Rlim value, the lower Over current protection
accuracy.
Indeed, the current is measured by a voltage comparator
on a serial resistance. If this voltage drop comes very small,
the offset of the internal comparator will have an impact on
Over−voltage Lockout (OVLO)
To protect the connected system on IN pins, from external
over−voltage coming from USB connector or Wall Adapter,
through Vbus pin , the device has a built−in over−voltage
lock out (OVLO) circuit. During over−voltage condition,
http://onsemi.com
6
NCP373
into account the fault event and then disable reverse charge
path.
the accuracy. So a division by more than three times with
Rlim will degrade drastically the overcurrent accuracy.
The current limit calculation formula for the
NCP373MU04TXG is:
R LIM04 +
ǒ
I OCP
The current limit
NCP373MU13TXG is:
R LIM13 +
Ǔ
11521
* 29035
calculation
ǒ
Ǔ
37717
I OCP
To access to the Vbus mode, DIR pin must be tied to high
(>1.2) and EN must be tied from high to low (< 0.4 V).
In that case, the core of the NCP373 will be supplied by
the IN, with a 2.5 V minimum voltage and 5.5 V maximum
voltage.
In this state, OCP, OVLO and thermal modes are
available.
W
formula
* 29035
VBus Mode
for
the
W
During over current event, NMOSes are opened and
FLAG output is tied to low, allowing the mController to take
IN
Vbus
ton
tstart
FLAG
tREG
IREV
Ilim
EN
{}
{}
tRRD
ID
Over Current in Vbus
Transceiver
DIR
Figure 4. Over Current Protection Sequence
In Vbus Mode, FLAG pin remains available, allowing the
mcontroller to have a status regarding over−voltage
condition, over−current condition or thermal shutdown
condition.
http://onsemi.com
7
NCP373
Vbus
tON
IN
Battery output
FLAG
DIR
EN
Transciever
Transciever
Downstream Vbus connection
Figure 5. FLAG Status in Vbus Mode
Logic Inputs
DIR pin disconnects IN pin from Vbus pin. DIR does not
overdrive an OVLO or UVLO fault (FLAG status is still
available).
To enable Charge operation (Charge Mode), the DIR pin
shall be forced to low and EN to high. A high level on the
Table 1. TABLE SELECTION OF CHARGE MODES
Protection
DIR
EN
MODE
OVP @ VBUS (+28 V, −28 V,
OVLO 5.77 V)
0
0
NA
NA
NA
NA
0
1
Charge
Yes
NA
NA
1
0
VBUS
Yes
Yes
NA
1
1
Disable
Yes (out off)
NA
NA
Negative Voltage and Reverse Current
OCP (IN to VBUS)
OCP (VBUS to IN)
in order to instantaneously decrease the device temperature.
The thermal threshold has been set at 150°C. FLAG is then
tied to low to inform the MCU.
As the thermal hysteresis is 30°C, the MOSFET will be
closed as soon the device temperature falls down to 120°C.
If the fault event is still present, the temperature increase
one more time and engages the thermal shutdown one more
time until fault event disappeared.
The device protects the system connected on IN pin from
negative voltage occurring on Vbus pin, down to −28 V.
When a negative voltage occurs, the IN pins are
disconnected from Vbus pins. This negative protection is
available in all modes
Thermal Shutdown Protection
In case of internal overheating, the integrated thermal
shutdown protection allows to open the internal MOSFET
http://onsemi.com
8
NCP373
1.00
0.90
Power Curve with
PCB cu thk 1 oz
200
0.80
Power Curve with
PCB cu thk 2 oz
150
0.70
0.60
0.50
100
0.40
qJA Curve with
PCB cu thk 2 oz
50
0
0.30
0.20
qJA Curve with
PCB cu thk 1 oz
0
100
200
300
400
0.10
500
600
0.00
700
TOTAL POWER INTO PACKAGE (W)
MAXIMUM qTA (°C/W)
250
COPPER HEAT SPREAD AREA (mm2)
Figure 6. Copper Heat Spread Area
ESD Tests
PCB Recommendations
The NCP373 conforms to the IEC61000−4−2, level 4 on
the Input pin. A 1 mF (I.E Murata GRM188R61E105KA12D)
must be placed close to the IN pins. If the IEC61000−4−2 is
not a requirement, a 100 nF/25 V must be placed between IN
and GND.
The above configuration supports 15 kV (Air) and 8 kV
(Contact) at the input per IEC61000−4−2 (level 4).
Please refer to Figure 7 for the IEC61000−4−2
electrostatic discharge waveform.
The under PAD1 of the NCP373 package shall be
connected to an isolated PCB area to increase the heat
transfer if necessary for an application standpoint.
In any case, the PAD1 shall be not connected to any other
potential or GND than the isolated extra copper surface.
Following figure shows copper area according to RqJA
and allows the design of the transfer plane connected to
PAD1.
Figure 7. Ipeak = f(t)/IEC61000−4−2
ORDERING INFORMATION
Marking
Order Current Limit
Package
Shipping†
NCP373MU04TXG
NCAI
400 mA
LLGA12 3 x 3 mm
(Pb−Free)
3000 Tape / Reel
NCP373MU13TXG
NC13
1300 mA
LLGA12 3 x 3 mm
(Pb−Free)
3000 Tape / Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
9
NCP373
PACKAGE DIMENSIONS
LLGA12 3x3, 0.5P
CASE 513AK−01
ISSUE O
PIN ONE
REFERENCE
2X
0.15 C
2X
ÇÇÇ
ÇÇÇ
ÇÇÇ
0.15 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 MM FROM TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
A B
D
E
DIM
A
A1
b
D
D2
E
E2
e
K
L
TOP VIEW
0.10 C
A
12X
0.08 C
MILLIMETERS
MIN
MAX
0.50
0.60
0.00
0.05
0.20
0.30
3.00 BSC
2.60
2.80
3.00 BSC
1.90
2.10
0.50 BSC
0.20
−−−
0.25
0.35
SOLDERING FOOTPRINT*
A1
SIDE VIEW
C
SEATING
PLANE
3.30
D2
1
6
e
12X
0.50
1
0.50
PITCH
0.43
2.75
12X
K
E2
11X
0.30
12X
L
12
7
12X
b
BOTTOM VIEW
0.10 C A B
0.05 C
2.05
DIMENSIONS: MILLIMETERS
NOTE 3
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP373/D