EN7980 D

Ordering number : E*N7980
LC75857E
LC75857W
http://onsemi.com
Advance Information
CMOS LSI
1/3, 1/4 Duty LCD Driver
with Key Input Function
Overview
The LC75857E and LC75857W are 1/3 duty and 1/4 duty LCD display drivers that can directly drive up to 164
segments and can control up to four general-purpose output ports. These products also incorporate a key scan circuit
that accepts input from up to 30 keys to reduce printed circuit board wiring.
Features
 Key input function for up to 30 keys (A key scan is performed only when a key is pressed.)
 1/3 duty and 1/4 duty drive schemes can be controlled from serial data.
 1/2 bias and 1/3 bias drive schemes can be controlled from serial data.
 Capable of driving up to 126 segments using 1/3 duty and up to 164 segments using 1/4 duty.
 Sleep mode and all segments off functions that are controlled from serial data.
 Switching between key scan output and segment output can be controlled from the serial data.
 The key scan operation enabled/disabled state can be controlled from the serial data.
 Switching between segment output port and general-purpose output port can be controlled from serial data.
 The common and segment output waveform frame frequency can be controlled from the serial data.
 Switching between RC oscillator mode and external clock mode can be controlled from the serial data.
 Serial data I/O supports CCB format communication with the system controller.
 Direct display of display data without the use of a decoder provides high generality.
 Independent VLCD for the LCD driver block.
(When the logic block supply voltage VDD is in the range 3.6 to 6.0 V, VLCD can be set to a voltage in the range 0.75
VDD to 6.0 V, and when VDD is in the range 2.7 to 3.6 V, VLCD can be set to a voltage in the range 2.7 to 6.0 V.)
 Provision of an on-chip voltage-detection type reset circuit prevents incorrect displays.


CCB is ON Semiconductor® ’s original format. All addresses are managed
by ON Semiconductor® for this format.
CCB is a registered trademark of Semiconductor Components Industries, LLC.
This document contains information on a new product. Specifications and information
herein are subject to change without notice.
Semiconductor Components Industries, LLC, 2013
July, 2013
92504TN (OT) No.7980-1/39
LC75857E, LC75857W
Specifications
Absolute Maximum Ratings at Ta=25°C, VSS=0V
Parameter
Maximum supply voltage
Input voltage
Output voltage
Output current
Allowable power dissipation
Symbol
Conditions
Ratings
Unit
VDD max
VDD
–0.3 to +7.0
VLCD max
VLCD
–0.3 to +7.0
VIN1
CE, CL, DI
–0.3 to +7.0
VIN2
OSC,TEST
–0.3 to VDD +0.3
VIN3
VLCD1, VLCD2, KI1 to KI5
V
–0.3 to VLCD +0.3
VOUT1
DO
VOUT2
OSC
VOUT3
S1 to S42, COM1 to COM4, KS1 to KS6, P1 to P4
IOUT1
S1 to S42
IOUT2
COM1 to COM4
3
IOUT3
KS1 to KS6
1
IOUT4
P1 to P4
5
Pd max
V
–0.3 to +7.0
–0.3 to VDD +0.3
V
–0.3 to VLCD +0.3
300
Ta = 85°C
200
µA
mA
mW
Operating temperature
Topr
–40 to +85
°C
Storage temperature
Tstg
–55 to +125
°C
Allowable Operating Ranges at Ta = –40 to +85°C, VSS=0V
Parameter
Symbol
VDD
Supply voltage
Input voltage
Input high level voltage
Input low level voltage
VLCD
Ratings
Conditions
min
VDD
typ
Unit
max
2.7
6.0
VLCD: VDD = 3.6 V to 6.0 V
0.75 VDD
6.0
VLCD: VDD = 2.7 V to 3.6 V
2.7
6.0
VLCD1
VLCD1
2/3 VLCD
VLCD
VLCD2
VLCD2
1/3 VLCD
VLCD
VIH1
CE, CL, DI
0.8 VDD
6.0
VIH2
KI1 to KI5
0.6 VLCD
VLCD
VIH3
OSC: External clock mode
0.7 VDD
VDD
VIL1
CE, CL, DI
0
0.2 VDD
VIL2
KI1 to KI5
0
0.2 VLCD
VIL3
OSC: External clock mode
0
0.3 VDD
Recommended RC oscillator external resistor
ROSC
OSC: RC oscillator mode
39
Recommended RC oscillator external capacitor
COSC
OSC: RC oscillator mode
1000
Guaranteed RC oscillator operating range
fOSC
OSC: RC oscillator mode
External clock frequency
fCK
OSC: External clock mode
External clock duty
DCK
OSC: External clock mode
V
V
V
V
kΩ
pF
19
38
76
kHz
:Figure 4
19
38
76
kHz
:Figure 4
30
50
70
%
Data setup time
tds
CL, DI
:Figures 2,3
160
ns
Data hold time
tdh
CL, DI
:Figures 2,3
160
ns
CE wait time
tcp
CE, CL
:Figures 2,3
160
ns
CE setup time
tcs
CE, CL
:Figures 2,3
160
ns
CE hold time
tch
CE, CL
:Figures 2,3
160
ns
High level clock pulse width
tøH
CL
:Figures 2,3
160
ns
Low level clock pulse width
tøL
CL
:Figures 2,3
160
ns
Rise time
tr
CE, CL, DI
:Figures 2,3
160
Fall time
tf
CE, CL, DI
:Figures 2,3
160
ns
ns
DO output delay time
tdc
DO RPU=4.7 kΩ, CL=10pF *1
:Figures 2,3
1.5
µs
DO rise time
tdr
DO RPU=4.7 kΩ, CL=10pF *1
:Figures 2,3
1.5
µs
Note: *1. Since DO is an open-drain output, these values depend on the resistance of the pull-up resistor RPU and the load capacitance CL.
No. 7980-2/39
LC75857E, 75857W
Electrical Characteristics for the Allowable Operation Ranges
Parameter
Symbol
Hysteresis
Power-down detection voltage
Ratings
Conditions
min
VH1
CE, CL, DI
0.1 VDD
KI1 to KI5
0.1 VLCD
Input low level current
Input floating voltage
Pull-down resistance
5.0
IIH2
OSC: VI = VDD External clock mode
5.0
IIL1
CE, CL, DI: VI = 0 V
–5.0
IIL2
OSC: VI = 0 V External clock mode
–5.0
VIF
KI1 to KI5
VOH1
Output middle level voltage *2
0.05 VLCD
KI1 to KI5: VLCD = 5.0 V
50
100
250
KI1 to KI5: VLCD = 3.0 V
100
200
500
DO: VO = 6.0 V
6.0
KS1 to KS6: IO = –500 µA VLCD = 3.6 to 6.0 V
KS1 to KS6: IO = –250 µA VLCD = 2.7 to 3.6 V
VLCD – 0.8 VLCD – 0.4 VLCD – 0.1
P1 to P4: IO = –1 mA
VLCD – 0.9
VOH3
S1 to S42: IO = –20 µA
VLCD – 0.9
VOH4
COM1 to COM4: IO = –100 µA
VLCD – 0.9
V
k
µA
V
KS1 to KS6: IO = 25 µA VLCD = 3.6 to 6.0 V
0.2
0.5
1.5
KS1 to KS6: IO = 12.5 µA VLCD = 2.7 to 3.6 V
0.1
0.4
1.2
VOL2
P1 to P4: IO = 1 mA
0.9
VOL3
S1 to S42: IO = 20 µA
0.9
VOL4
COM1 to COM4: IO = 100 µA
DO: IO = 1 mA
VMID1
COM1 to COM4: 1/2 bias, IO = ±100 µA
1/2 VLCD – 0.9
1/2 VLCD + 0.9
VMID2
S1 to S42: 1/3 bias,IO = ±20 µA
2/3 VLCD – 0.9
2/3 VLCD + 0.9
VMID3
S1 to S42: 1/3 bias, IO = ±20 µA
1/3 VLCD – 0.9
1/3 VLCD + 0.9
VMID4
COM1 to COM4: 1/3 bias,IO = ±100 µA
2/3 VLCD – 0.9
2/3 VLCD + 0.9
VMID5
COM1 to COM4: 1/3 bias,IO = ±100 µA
1/3 VLCD – 0.9
fosc
OSC: ROSC = 39 k , COSC = 1000 pF
IDD1
VDD :Sleep mode
V
0.9
0.1
0.5
V
1/3 VLCD + 0.9
30.4
38
45.6
kHz
100
IDD2
VDD: VDD = 6.0 V, output open,fosc = 38 kHz
ILCD1
VLCD : Sleep mode
ILCD2
VLCD: VLCD = 6.0 V, output open, 1/2 bias,
fosc = 38 kHz
100
200
ILCD3
VLCD: VLCD = 6.0 V, output open, 1/3 bias,
fosc = 38 kHz
60
120
Current drain
µA
VLCD – 1.0 VLCD – 0.5 VLCD – 0.2
VOL5
Oscillator frequency
V
µA
VOH2
VOL1
Output low level voltage
2.4
CE, CL, DI: VI = 6.0 V
IOFFH
Output high level voltage
2.2
V
IIH1
RPD
Output off leakage current
2.0
Unit
max
VH2
VDET
Input high level current
typ
300
600
5
µA
Nete: *2. Excluding the bias voltage generation divider resistor built into VLCD1 and VLCD2. (See Figure 1.)
Package Dimensions
[ LC75857E ]
unit : mm (typ)
33
12.0
32
49
0.5
10.0
48
33
64
32
10.0
17.2
14.0
49
64
17
17
1
1
0.35
16
0.5
16
0.8
0.15
12.0
48
0.8
17.2
14.0
[ LC75857W ]
0.18
0.15
(1.25)
0.1
3.0max
1.7max
(2.7)
(1.5)
(1.0)
0.1
SQFP64(10X10)
QIP64E(14X14)
No.7980-3/39
LC75857E, LC75857W
VLCD
VLCD1
To the common segment driver
VLCD2
Excluding these registors.
Figure 1
1. Serial data I/O timing when CL is stopped at the low level
VIH1
CE
CL
VIL1
tø H
VIH1
50%
VIL1
tø L
tr
DI
tf
tch
tcp tcs
VIH1
VIL1
tds
tdh
tdc
DO
D0
tdr
D1
Figure 2
2. Serial data I/O timing when CL is stopped at the high level
VIH1
CE
VIL1
tø L
tø H
VIH1
50%
VIL1
CL
tf
tr
tcp tcs
tch
VIH1
VIL1
DI
tds
tdh
DO
D0
D1
tdc
tdr
Figure 3
3. OSC pin clock timing in external clock mode
tCKH
OSC
tCKL
VIH3
50%
VIL3
fCK =
1
[kHz]
tCKH + tCKL
DCK =
tCKH
×100[%]
tCKH + tCKL
Figure 4
No. 7980-4/39
LC75857E, LC75857W
KS6
KS5
KS4
KS3/S42
KS2/S41
KS1/S40
COM1
COM2
COM3
COM4/S39
S38
S37
S36
S35
S34
S33
Pin Assignments
48
33
49
32
KI1
KI2
KI3
KI4
KI5
VDD
VLCD
VLCD1
VLCD2
VSS
TEST
OSC
DO
CE
CL
DI
S32
S31
S30
S29
S28
S27
S26
S25
S24
S23
S22
S21
S20
S19
S18
S17
LC75857E/W
64
17
16
P1/S1
P2/S2
P3/S3
P4/S4
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
S16
1
Top view
No. 7980-5/39
LC75857E, LC75857W
S1/P1
S2/P2
S3/P3
S5
S4/P4
S38
COM4/S39
COM3
COM2
COM1
Block Diagram
VLCD
SEGMENT DRIVER & LATCH
VLCD1
COMMON
DRIVER
VLCD2
VSS
TEST
CLOCK
GENERATOR
OSC
CONTROL
REGISTER
DO
SHIFT REGISTER
CCB
INTERFACE
DI
CL
KEY BUFFER
CE
VDD
KS6
KS5
KS4
S42/KS3
S41/KS2
S40/KS1
KEY SCAN
KI5
KI4
KI3
KI2
KI1
VDET
No. 7980-6/39
LC75857E, LC75857W
Pin Functions
Pin
Pin No.
S1/P1 to
S4/P4
S5 to S38
1 to 4
COM1
to
COM3
COM4/S39
5 to 38
42 to 40
39
Active
I/O
Handling
when unused
Segment outputs for displaying the display data transferred by serial data input.
The S1/P1 to S4/P4 pins can be used as general-purpose output ports under serial
data control.
—
O
OPEN
Common driver outputs
The frame frequency is fo [Hz]
The COM4/S39 pin can be used as a segment output in 1/3 duty.
—
O
OPEN
—
O
OPEN
Function
KS1/S40
KS2/S41
KS3/S42
KS4 to KS6
43
44
45
46 to 48
Key scan outputs
Although normal key scan timing lines require diodes to be inserted in the timing lines
to prevent shorts, since these outputs are unbalanced CMOS transistor outputs, these
outputs will not be damaged by shorting when these outputs are used to form a key
matrix. The KS1/S40 to KS3/S42 pins can be used as segment outputs when so
specified by the control data.
KI1 to KI5
49 to 53
Key scan inputs
These pins have built-in pull-down resistors.
H
I
GND
OSC
60
The OSC pin can be used to form an oscillator circuit with an external resistor and an
external capacitor. If external clock mode is selected with the control data, this pin is
used to input an external clock signal.
—
I/O
VDD
CE
62
H
I
CL
63
DI
64
DO
61
Serial data interface connections to the controller. Note that DO, being an open-drain
output, requires a pull-up resistor.
CE :Chip enable
CL :Synchronization clock
DI :Transfer data
DO :Output data
—
O
OPEN
TEST
59
This pin must be connected to ground.
—
I
—
VLCD1
56
Used for applying the LCD drive 2/3 bias voltage externally. Must be connected to
VLCD2 when a 1/2 bias drive scheme is used.
—
I
OPEN
VLCD2
57
Used for applying the LCD drive 1/3 bias voltage externally. Must be connected to
VLCD1 when a 1/2 bias drive scheme is used.
—
I
OPEN
VDD
54
Logic block power supply connection. Provide a voltage of between 2.7 and 6.0V.
—
—
—
VLCD
55
LCD driver block power supply connection. A voltage in the range 0.75 × VDD to 6.0 V
must be provided when VDD is in the range 3.6 to 6.0 V, and a voltage in the range
2.7 V to 6.0 V must be provided when VDD is in the range 2.7 to 3.6 V.
—
—
—
VSS
58
Power supply connection. Connect to ground.
—
—
—
I
—
I
GND
No. 7980-7/39
LC75857E, LC75857W
Serial Data Input
1. 1/3 duty
(1) When CL is stopped at the low level
CE
CL
DI
0
1
0
0
0
0 1
0
B0 B1 B2 B3 A0 A1 A2 A3
D1 D2
D41 D42 0
0
0 SP KC0 KC1 KC2 KSC K0 K1 P0 P1 P2 SC DR DT FC0 FC1 FC2 0C 0
Display data
Control data
0
DD
DO
0
1
0
0
0
0
1
0 D43 D44
B0 B1 B2 B3 A0 A1 A2 A3
0
1
0
0
0
0
1
D83 D84 0
0 D85 D86
B0 B1 B2 B3 A0 A1 A2 A3
0
0
0
0
0
0
0
Display data
Display data
0
0
0
0
0
0
0
0
0
0
0
0
Fixed data
D125 D126 0
0
0
0
0
0
0
0
0
0
0
Fixed data
0
1
DD
0
0
0
0
0
0
0
0
0
1
0
DD
Note: B0 to B3, A0 to A3 ...... CCB address
DD ................................ Direction data
No. 7980-8/39
LC75857E, LC75857W
(2) When CL is stopped at the high level
CE
CL
DI
0
1
0
0
0
0
1
0
B0 B1 B2 B3 A0 A1 A2 A3
D1 D2
D41 D42 0
0
0 SP KC0 KC1 KC2 KSC K0 K1 P0 P1 P2 SC DR DT FC0 FC1 FC2 0C
Display data
0
Control data
0
DD
DO
0
0 1 0 0 0 0 1
B0 B1 B2 B3 A0 A1 A2 A3
D43 D44
D83 D84 0
0
0
0
0
0
0
0
0
0 1 0 0 0 0 1
0 D85 D86
D125 D126 0
B0 B1 B2 B3 A0 A1 A2 A3
Display data
0
0
0
0
0
0
0
0
0
0
0
Fixed data
Display data
0
0
0
0
0
0
0
0
0
0
0
Fixed data
0
1
DD
0
0
0
0
0
0
0
0
1
0
DD
Note: B0 to B3, A0 to A3 ...... CCB address
DD ................................ Direction data
CCB address ............ 42H
D1 to D126 .............. Display data
SP ............................ Normal mode/sleep mode control data
KC0 to KC2 .............. Key scan output state setting data
KSC .......................... Key scan operation enabled/disabled state setting data
K0, K1 ...................... Key scan output/segment output selection data
P0 to P2 .................. Segment output port/general-purpose output port selection data
SC ............................ Segment on/off control data
DR ............................ 1/2 bias or 1/3 bias drive selection data
DT ............................ 1/3 duty or 1/4 duty drive selection data
FC0 to FC2 .............. Common and segment output waveform frame frequency setting data
OC ............................ RC oscillator mode/external clock mode switching selection data
No. 7980-9/39
LC75857E, LC75857W
2. 1/4duty
(1) When CL is stopped at the low level
CE
CL
DI
0
1
0
0
0
0
1
0
D1
B0 B1 B2 B3 A0 A1 A2 A3
D40 D41 D42 D43 D44 0 SP KC0 KC1 KC2 KSC K0 K1 P0 P1 P2 SC DR DT FC0 FC1 FC2 0C 0
Control data
Display data
0
DD
DO
0
1
0
0
0
0
1
0 D45
B0 B1 B2 B3 A0 A1 A2 A3
0
1
0
0
0
0
1
0 D85
B0 B1 B2 B3 A0 A1 A2 A3
0
1
0
0
0
0
1
D84 0
0
0
0
0
0
0
0
0
D124 0
Display data
D164 0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Fixed data
1
1
0
DD
Fixed data
0
0
DD
Fixed data
Display data
0 D125
B0 B1 B2 B3 A0 A1 A2 A3
0
Display data
0
0
0
0
0
0
0
0
0
1
1
DD
Note: B0 to B3, A0 to A3 ...... CCB address
DD ................................ Direction data
No. 7980-10/39
LC75857E, LC75857W
(2) When CL is stopped at the high level
CE
CL
DI
0
1
0
0
0
0
1
0
D1
D40 D41 D42 D43 D44 0
SP KC0 KC1 KC2 KSC K0 K1 P0 P1 P2 SC DR DT FC0 FC1 FC2 0C
Control data
Display data
B0 B1 B2 B3 A0 A1 A2 A3
0
0
DD
DO
0
1
0
0
0
0
1
0
B0 B1 B2 B3 A0 A1 A2 A3
0
1
0
0
0
0
1
0
B0 B1 B2 B3 A0 A1 A2 A3
0
1
0
0
0
0
1
0
B0 B1 B2 B3 A0 A1 A2 A3
D45
D84 0
0
0
0
0
0
0
0
0
0
Display data
D85
D124 0
0
0
0
0
0
0
0
0
0
D164 0
Display data
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
DD
0
0
0
0
0
0
0
0
0
1
0
DD
Fixed data
Display data
D125
0
Fixed data
0
Fixed data
0
0
0
0
0
0
0
0
0
1
1
DD
Note: B0 to B3, A0 to A3 ...... CCB address
DD ................................ Direction data
CCB address ............ 42H
D1 to D164 .............. Display data
SP ............................ Normal mode/sleep mode control data
KC0 to KC2 .............. Key scan output state setting data
KSC .......................... Key scan operation enabled/disabled state setting data
K0, K1 ...................... Key scan output/segment output selection data
P0 to P2 .................. Segment output port/general-purpose output port selection data
SC ............................ Segment on/off control data
DR ............................ 1/2 bias or 1/3 bias drive selection data
DT ............................ 1/3 duty or 1/4 duty drive selection data
FC0 to FC2 .............. Common and segment output waveform frame frequency setting data
OC ............................ RC oscillator mode/external clock mode switching selection data
No. 7980-11/39
LC75857E, 75857W
Control Data Functions
1. SP : Normal mode/sleep mode control data
This control data bit switches the IC between normal mode and sleep mode.
SP
Mode
0
Normal
1
sleep
OSC pin state
RC oscillator mode
External clock mode
Common and segment
pin output states
Oscillator operating
External clock signal accepted
LCD drive waveforms
are output
Oscillator stopped
Acceptance of the external
(The oscillator operates
clock signal is disabled.
Key scan
operating state
General-purpose
output port states
The state can be set The state can be set
L (VSS)
during key scan operations.) (The external clock signal is accepted
during key scan operations)
Note:
See the descriptions of the KC0 to KC2, KSC, K0, K1, and P0 to P2 bits in the control data for details on setting the key scan operating state and
setting the general-purpose output port state.
2. KC0 to KC2 : Key scan output state setting data
These control data bits set the states of the key scan output pins KS1 to KS6.
Control data
Output pin states during key scan standby
KC0
KC1
KC2
KS1
KS2
KS3
KS4
KS5
KS6
0
0
0
H
H
H
H
H
H
0
0
1
L
H
H
H
H
H
0
1
0
L
L
H
H
H
H
0
1
1
L
L
L
H
H
H
1
0
0
L
L
L
L
H
H
1
0
1
L
L
L
L
L
H
1
1
0
L
L
L
L
L
L
Note:
This assumes that the KS1/S40 to KS3/S42 output pins are selected for key scan output.
Also note that key scan output signals are not output from output pins that are set to the low level.
3. KSC : Key scan operation enabled/disabled state setting data
This control data bit enables or disables key scan operation.
KSC
Key scan operating state
0
Key scan operation enabled
(A key scan operation is performed if any key on the lines corresponding to KS1 to KS6 pin which is set high is pressed .)
Key scan operation disabled
(No key scan operation is performed, even if any of the keys in the key matrix are pressed. If this state is set up, the key data
is forcibly reset to 0 and the key data read request is also cleared. (DO is set high.))
1
4. K0, K1 : Key scan output /segment output selection data
These control data bits switch the functions of the KS1/S40 to KS3/S42 output pins between key scan output and
segment output.
Control data
Output pin state
KS2/S41
KS3/S42
Maximum number of
input keys
K0
K1
KS1/S40
0
0
KS1
KS2
KS3
30
0
1
S40
KS2
KS3
25
1
0
S40
S41
KS3
20
1
1
S40
S41
S42
15
Note: KSn(n = 1 to 3) : Key scan output
Sn (n = 40 to 42): Segment output
No.7980-12/39
LC75857E, LC75857W
5. P0 to P2 : Segment output port/general-purpose output port selection data
These control data bits switch the functions of the S1/P1 to S4/P4 output pins between the segment output port and
the general-purpose output port.
Control data
Output pin state
P0
P1
P2
S1/P1
S2/P2
S3/P3
S4/P4
0
0
0
S1
S2
S3
S4
0
0
1
P1
S2
S3
S4
0
1
0
P1
P2
S3
S4
0
1
1
P1
P2
P3
S4
1
0
0
P1
P2
P3
P4
Note: Sn(n=1 to 4): Segment output port
Pn(n=1 to 4): General-purpose output port
The table below lists the correspondence between the display data and the output pins when these pins are selected to
be general-purpose output ports.
Corresponding display data
Output pin
1/3 duty
1/4 duty
S1/P1
D1
D1
S2/P2
D4
D5
S3/P3
D7
D9
S4/P4
D10
D13
For example, if the circuit is operated in 1/4 duty and the S4/P4 output pin is selected to be a general-purpose output
port, the S4/P4 output pin will output a high level (VLCD) when the display data D13 is 1, and will output a low level
(Vss) when D13 is 0.
6. SC : Segment on/off control data
This control data bit controls the on/off state of the segments.
SC
Display state
0
on
1
off
However, note that when the segments are turned off by setting SC to 1, the segments are turned off by outputting
segment off waveforms from the segment output pins.
7. DR : 1/2 bias or 1/3 bias drive selection data
This control data bit switches between LCD 1/2 bias or 1/3 bias drive.
DR
Bias drive scheme
0
1/3 bias drive
1
1/2 bias drive
8. DT : 1/3 duty or 1/4 duty drive selection data
This control data bit switches between LCD 1/3 duty or 1/4 duty drive.
DT
Duty drive scheme
Output pin state (COM4/S39)
0
1/4 duty drive
COM4
1
1/3 duty drive
S39
Note: COM4: Common output
S39 : Segment output
No. 7980-13/39
LC75857E, LC75857W
9. FC0 to FC2 : Common and segment output waveform frame frequency setting data
These control data bits set the common and segment output waveform frequency.
Control data
FC0
FC1
Frame frequency, fo (Hz)
FC2
0
0
0
fOSC/768, fCK/768
0
0
1
fOSC/576, fCK/576
0
1
0
fOSC/384, fCK/384
0
1
1
fOSC/288, fCK/288
1
0
0
fOSC/192, fCK/192
10. OC : RC oscillator mode/external clock mode switching selection data
This control data bit selects the OSC pin function (RC oscillator mode or external clock mode).
OC
OSC pin function
0
RC oscillator mode
1
External clock mode
Note:
If RC oscillator mode is selected, connect an external resistor Rosc and an external capacitor Cosc to the OSC pin.
Display Data and Output Pin Correspondence
1. 1/3 duty
Output pin
COM1
COM2
COM3
Output pin
COM1
COM2
COM3
S1/P1
D1
D2
D3
S22
D64
D65
D66
S2/P2
D4
D5
D6
S23
D67
D68
D69
S3/P3
D7
D8
D9
S24
D70
D71
D72
S4/P4
D10
D11
D12
S25
D73
D74
D75
S5
D13
D14
D15
S26
D76
D77
D78
S6
D16
D17
D18
S27
D79
D80
D81
S7
D19
D20
D21
S28
D82
D83
D84
S8
D22
D23
D24
S29
D85
D86
D87
S9
D25
D26
D27
S30
D88
D89
D90
S10
D28
D29
D30
S31
D91
D92
D93
S11
D31
D32
D33
S32
D94
D95
D96
S12
D34
D35
D36
S33
D97
D98
D99
S13
D37
D38
D39
S34
D100
D101
D102
S14
D40
D41
D42
S35
D103
D104
D105
S15
D43
D44
D45
S36
D106
D107
D108
S16
D46
D47
D48
S37
D109
D110
D111
S17
D49
D50
D51
S38
D112
D113
D114
S18
D52
D53
D54
COM4/S39
D115
D116
D117
S19
D55
D56
D57
KS1/S40
D118
D119
D120
S20
D58
D59
D60
KS2/S41
D121
D122
D123
S21
D61
D62
D63
KS3/S42
D124
D125
D126
Note: This is for the case where the output pins S1/P1 to S4/P4, COM4/S74, KS1/S40 to KS3/S42 are selected for use as segment outputs.
For example, the table below lists the segment output states for the S11 output pin.
Display data
Output pin state (S11)
D31
D32
D33
0
0
0
The LCD segments for COM1, COM2 and COM3 are off.
0
0
1
The LCD segment for COM3 is on.
0
1
0
The LCD segment for COM2 is on.
0
1
1
The LCD segments for COM2 and COM3 are on.
1
0
0
The LCD segment for COM1 is on.
1
0
1
The LCD segments for COM1 and COM3 are on.
1
1
0
The LCD segments for COM1 and COM2 are on.
1
1
1
The LCD segments for COM1, COM2 and COM3 are on.
No. 7980-14/39
LC75857E, LC75857W
2. 1/4 duty
Output pin
COM1
COM2
COM3
COM4
Output pin
COM1
COM2
COM3
COM4
S1/P1
D1
D2
D3
D4
S22
D85
D86
D87
D88
S2/P2
D5
D6
D7
D8
S23
D89
D90
D91
D92
S3/P3
D9
D10
D11
D12
S24
D93
D94
D95
D96
S4/P4
D13
D14
D15
D16
S25
D97
D98
D99
D100
S5
D17
D18
D19
D20
S26
D101
D102
D103
D104
S6
D21
D22
D23
D24
S27
D105
D106
D107
D108
S7
D25
D26
D27
D28
S28
D109
D110
D111
D112
S8
D29
D30
D31
D32
S29
D113
D114
D115
D116
S9
D33
D34
D35
D36
S30
D117
D118
D119
D120
S10
D37
D38
D39
D40
S31
D121
D122
D123
D124
S11
D41
D42
D43
D44
S32
D125
D126
D127
D128
S12
D45
D46
D47
D48
S33
D129
D130
D131
D132
S13
D49
D50
D51
D52
S34
D133
D134
D135
D136
S14
D53
D54
D55
D56
S35
D137
D138
D139
D140
S15
D57
D58
D59
D60
S36
D141
D142
D143
D144
S16
D61
D62
D63
D64
S37
D145
D146
D147
D148
S17
D65
D66
D67
D68
S38
D149
D150
D151
D152
S18
D69
D70
D71
D72
KS1/S40
D153
D154
D155
D156
S19
D73
D74
D75
D76
KS2/S41
D157
D158
D159
D160
S20
D77
D78
D79
D80
KS3/S42
D161
D162
D163
D164
S21
D81
D82
D83
D84
Note: This is for the case where the output pins S1/P1 to S4/P4, KS1/S40 to KS3/S42 are selected for use as segment outputs.
For example, the table below lists the segment output states for the S11 output pin.
Display data
D41
D42
D43
D44
Output pin state (S11)
0
0
0
0
The LCD segments for COM1,COM2,COM3 and COM4 are off.
0
0
0
1
The LCD segment for COM4 is on.
0
0
1
0
The LCD segment for COM3 is on.
0
0
1
1
The LCD segments for COM3 and COM4 are on.
0
1
0
0
The LCD segment for COM2 is on.
0
1
0
1
The LCD segments for COM2 and COM4 are on.
0
1
1
0
The LCD segments for COM2 and COM3 are on.
0
1
1
1
The LCD segments for COM2,COM3 and COM4 are on.
1
0
0
0
The LCD segment for COM1 is on.
1
0
0
1
The LCD segments for COM1 and COM4 are on.
1
0
1
0
The LCD segments for COM1 and COM3 are on.
1
0
1
1
The LCD segments for COM1,COM3 and COM4 are on.
1
1
0
0
The LCD segments for COM1 and COM2 are on.
1
1
0
1
The LCD segments for COM1,COM2 and COM4 are on.
1
1
1
0
The LCD segments for COM1,COM2 and COM3 are on.
1
1
1
1
The LCD segments for COM1,COM2,COM3 and COM4 are on.
No. 7980-15/39
LC75857E, LC75857W
Serial Data Output
1. When CL is stopped at the low level
CE
CL
DI
1
1
0
0
0
0
1
0
B0
B1
B2
B3
A0
A1
A2
A3
DO
X
KD1 KD2
KD27 KD28 KD29 KD30 SA
Output data
X: don't care
Note: B0 to B3, A0 to A3······CCB address
2. When CL is stopped at the high level
CE
CL
DI
1
1
0
0
0
0
1
0
B0
B1
B2
B3
A0
A1
A2
A3
DO
KD28 KD29 KD30 SA
X KD1 KD2 KD3
X
Output data
X: don't care
Note: B0 to B3, A0 to A3······CCB address
CCB address ...... 43H
KD1 to KD30 ........ Key data
SA ........................ Sleep acknowledge data
Note: If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge data(SA) will be invalid.
No. 7980-16/39
LC75857E, LC75857W
Output Data
1. KD1 to KD30 : Key data
When a key matrix of up to 30 keys is formed from the KS1 to KS6 output pins and the KI1 to KI5 input pins and
one of those keys is pressed, the key output data corresponding to that key will be set to 1. The table shows the
relationship between those pins and the key data bits.
KS1/S40
KI1
KI2
KI3
KI4
KI5
KD1
KD2
KD3
KD4
KD5
KS2/S41
KD6
KD7
KD8
KD9
KD10
KS3/S42
KD11
KD12
KD13
KD14
KD15
KS4
KD16
KD17
KD18
KD19
KD20
KS5
KD21
KD22
KD23
KD24
KD25
KS6
KD26
KD27
KD28
KD29
KD30
When the KS1/S40 and KS2/S41 output pins are selected to be segment outputs by control data bits K0 and K1 and a
key matrix of up to 20 keys is formed using the KS3/S42,KS4 to KS6 output pins and the KI1 to KI5 input pins, the
KD1 to KD10 key data bits will be set to 0.
2. SA : Sleep acknowledge data
This output data bit is set to the state when the key was pressed. Also, while DO will be low in this case, if serial data
is input and the mode is set (to normal or sleep mode) during this period, that mode will be set. SA will be 1 in sleep
mode and 0 in normal mode.
Sleep Mode Functions
Sleep mode is set up by setting SP in the control data to 1. When sleep mode is set up, both the segment and the common
outputs will go to the low level. In RC oscillator mode (OC = 0), the oscillator on the OSC pin will stop (although it will
operate during key scan operations), and in external clock mode (OC = 1), the external clock signal reception on the OSC
pin will stop (although the clock signal will be received during key scan operations). Thus this mode reduces power
consumption. However, the S1/P1 to S4/P4 output pins can be used as general-purpose output ports under control of the
P0 to P2 bits in the control data even in sleep mode. Sleep mode is cancelled by setting SP in the control data to 0.
No. 7980-17/39
LC75857E, LC75857W
Key Scan Operation Functions
1. Key scan timing
The key scan period is 288T(s). To reliably determine the on/off state of the keys, the LC75857E/W scans the keys
twice and determines that a key has been pressed when the key data agrees. It outputs a key data read request (a low
level on DO) 615T(s) after starting a key scan. If the key data dose not agree and a key was pressed at that point, it
scans the keys again. Thus the LC75857E/W cannot detect a key press shorter than 615T(s).
KS1
*3
KS2
*3
KS3
*3
1
1
*3
2
2
*3
3
3
*3
T=
KS4
*3
KS5
*3
KS6
*3
4
4
5
*3
5
6
Key on
1
1
=
fCK
fosc
*3
6
*3
576T[s]
Note: *3. These are set to the high or low level by the KC0 to KC2 bits in the control data. Key scan output signals are not output from pins that are set to the low level.
2. Normal mode, when key scan operations are enabled
• The KS1 to KS6 pins are set to the high or low level by the KC0 to KC2 bits in the control data. (See the
description of the control data.)
• When any key on the lines corresponding to KS1 to KS6 pin which is set high is pressed, a key scan is
performed. Keys are scanned until all keys are released. Multiple key presses are recognized by determining
whether multiple key data bits are set.
1 ) the LC75857E/W outputs a key data read
1 = ——
• If a key is pressed for longer than 615 T (s) (Where T= ——
fCK
fosc
request (a low level on DO) to the controller. The controller acknowledges this request and reads the key data.
However, if CE is high during a serial data transfer, DO will be set high.
• After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75857E/W
performes another key scan. Also note that DO, being an open-drain output, requires a pull-up resistor (between 1
to 10 kΩ).
Key input 1
Key input 2
Key scan
615T[s]
615T[s]
615T[s]
CE
Serial data transfer
(KSC = 0)
Serial data transfer
(KSC = 0)
Key address (43H)
Serial data transfer
(KSC = 0)
Key address
Key address
DI
DO
Key data read
Key data read
Key data read request
Key data read request
Key data read
Key data read request
T=
1
1
=
fCK
fosc
No. 7980-18/39
LC75857E, LC75857W
3. Sleep mode, when key scan operations are enabled
• The KS1 to KS6 pins are set to the high or low level by the KC0 to KC2 bits in the control data. (See the
description of the control data.)
• When any key on the lines corresponding to KS1 to KS6 pin which is set high is pressed, either the OSC pin
oscillator starts (if the IC is in RC oscillator mode) or the IC starts accepting the external clock signal (if the IC is
in external clock mode), a key scan is performed. Keys are scanned until all keys are released. Multiple key
presses are recoghized by determinig whether multiple key data bits are set.
1 = ——
1 ) the LC75857E/W outputs a key data read
• If a key is pressed for longer than 615T(s)(Where T= ——
fosc fCK
request (a low level on DO) to the controller. The controller acknowledges this request and reads the key data.
However, if CE is high during a serial data transfer, DO will be set high.
• After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75857E/W
performs another key scan. However, this dose not clear sleep mode. Also note that DO, being an open-drain
output, requires a pull-up resistor (between 1 and 10 kΩ).
• Sleep mode key scan example
Example: KC0 = 1, KC1 = 0, KC2 = 1, (sleep with only KS6 high)
[L] KS1
[L] KS2
[L] KS3
[L] KS4
[L] KS5
[H] KS6
When any one of these keys is pressed, either the
OSC pin oscillator starts (if the IC is in RC
oscillator mode) or the IC starts accepting the
external clock signal (if the IC is in external clock
mode) and a key scan operation is performed.
*4
KI1
KI2
KI3
KI4
KI5
Note: *4. These diodes are required to reliable recognize multiple key presses on the KS6 line when sleep mode state with only KS6 high, as in the above
example. That is, these diodes prevent incorrect operations due to sneak currents in the KS6 key scan output signal when keys on the KS1 to KS5
lines are pressed at the same time.
Key input
(KS6 line)
Key scan
615T[s]
615T[s]
CE
Serial data transfer
(KSC = 0)
Serial data transfer
(KSC = 0)
Key address (43H)
Serial data transfer
(KSC = 0)
Key address
T=
DI
1
1
=
fosc
fCK
DO
Key data read
Key data read request
Key data read
Key data read request
No. 7980-19/39
LC75857E, LC75857W
4. Normal/sleep mode, when key scan operations are disabled
• The KS1 to KS6 pins are set to the high or low level by the KC0 to KC2 bits in the control data.
• No key scan operation is performed, whichever key is pressed.
• If the key scan disabled state (KSC = 1 in the control data) is set during a key scan, the key scan is stopped.
• If the key scan disabled state (KSC = 1 in the control data) is set when a key data read request (a low level on DO)
is output to the controller, all the key data is set to 0 and the key data read request is cleared (DO is set high).
Note that DO, being an open-drain output, requires a pull-up resister (between 1 to 10 kΩ).
• The key scan disabled state is cleared by setting KSC in the control data to 0.
Key input 1
Key input 2
Key scan
615T[s]
615T[s]
CE
Serial data transfer Serial data transfer
(KSC = 0)
(KSC = 1)
Serial data transfer
(KSC = 0)
Serial data transfer Serial data transfer
(KSC = 1)
(KSC = 0)
Key address
(43H)
DI
DO
Key data read request
Key data read request
T=
Key data
read
1
1
=
fosc fCK
Multiple Key Presses
Although the LC75857E/W is capable of key scanning without inserting diodes for dual key presses, triple key presses on
the KI1 to KI5 input pin lines, or multiple key presses on the KS1 to KS6 output pin lines, multiple presses other than
these cases may result in keys that were not pressed recognized as having been pressed. Therefore, a diode must be
inserted in series with each key. Applications that do not recognize multiple key presses of three or more keys should
check the key data for three or more 1 bits and ignore such data.
No. 7980-20/39
LC75857E, LC75857W
1/3 Duty, 1/2 Bias Drive Technique
fo[Hz]
COM1
VLCD
VLCD1,VLCD2
0V
COM2
VLCD
VLCD1,VLCD2
0V
COM3
VLCD
VLCD1,VLCD2
0V
LCD driver output when all LCD segments corresponding to
COM1, COM2 and COM3 are turned off.
VLCD
VLCD1,VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM1 are on
VLCD
VLCD1,VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM2 are on.
VLCD
VLCD1,VLCD2
0V
LCD driver output when LCD segments corresponding
to COM1 and COM2 are on.
VLCD
VLCD1,VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM3 are on.
VLCD
VLCD1,VLCD2
0V
LCD driver output when LCD segments corresponding
to COM1 and COM3 are on.
VLCD
VLCD1,VLCD2
0V
LCD driver output when LCD segments corresponding
to COM2 and COM3 are on.
VLCD
VLCD1,VLCD2
0V
LCD driver output when all LCD segments corresponding to
COM1, COM2 and COM3 are on.
VLCD
VLCD1,VLCD2
0V
1/3 Duty, 1/2 Bias Waveforms
Note: When FC0 = 0, FC1 = 0, and FC2 = 0 in the control data
f0 =
When FC0 = 0, FC1 = 0, and FC2 = 1 in the control data
f0 =
When FC0 = 0, FC1 = 1, and FC2 = 0 in the control data
f0 =
When FC0 = 0, FC1 = 1, and FC2 = 1 in the control data
f0 =
When FC0 = 1, FC1 = 0, and FC2 = 0 in the control data
f0 =
fosc
768
fosc
576
fosc
384
fosc
288
fosc
192
=
=
=
=
=
fCK
768
fCK
576
fCK
384
fCK
288
fCK
192
No. 7980-21/39
LC75857E, LC75857W
1/3 Duty, 1/3 Bias Drive Technique
fo[Hz]
COM1
VLCD
VLCD1
VLCD2
0V
COM2
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
COM3
LCD driver output when all LCD segments corresponding to
COM1, COM2 and COM3 are turned off.
VLCD
VLCD1
VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM1 are on.
VLCD
VLCD1
VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM2 are on.
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
LCD driver output when LCD segments corresponding
to COM1 and COM2 are on.
VLCD
VLCD1
VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM3 are on.
VLCD
VLCD1
VLCD2
0V
LCD driver output when LCD segments corresponding
to COM1 and COM3 are on.
VLCD
VLCD1
VLCD2
0V
LCD driver output when LCD segments corresponding
to COM2 and COM3 are on.
VLCD
VLCD1
VLCD2
0V
LCD driver output when all LCD segments
corresponding to COM1, COM2 and COM3 are on.
1/3 Duty, 1/3 Bias Waveforms
Note: When FC0 = 0, FC1 = 0, and FC2 = 0 in the control data
f0 =
When FC0 = 0, FC1 = 0, and FC2 = 1 in the control data
f0 =
When FC0 = 0, FC1 = 1, and FC2 = 0 in the control data
f0 =
When FC0 = 0, FC1 = 1, and FC2 = 1 in the control data
f0 =
When FC0 = 1, FC1 = 0, and FC2 = 0 in the control data
f0 =
fosc
768
fosc
576
fosc
384
fosc
288
fosc
192
=
=
=
=
=
fCK
768
fCK
576
fCK
384
fCK
288
fCK
192
No. 7980-22/39
LC75857E, LC75857W
1/4 Duty, 1/2 Bias Drive Technique
fo[Hz]
COM1
VLCD
VLCD1, VLCD2
0V
COM2
VLCD
VLCD1, VLCD2
0V
COM3
VLCD
VLCD1, VLCD2
0V
COM4
VLCD
VLCD1, VLCD2
0V
LCD driver output when all LCD segments corresponding to
COM1, COM2, COM3 and COM4 are turned off.
VLCD
VLCD1, VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM1 are on.
VLCD
VLCD1, VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM2 are on.
VLCD
VLCD1, VLCD2
0V
LCD driver output when LCD segments corresponding
to COM1 and COM2 are on.
VLCD
VLCD1, VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM3 are on.
VLCD
VLCD1, VLCD2
0V
LCD driver output when LCD segments corresponding
to COM1 and COM3 are on.
VLCD
VLCD1, VLCD2
0V
LCD driver output when LCD segments corresponding
to COM2 and COM3 are on.
VLCD
VLCD1, VLCD2
0V
LCD driver output when LCD segments corresponding
to COM1, COM2 and COM3 are on.
VLCD
VLCD1, VLCD2
0V
LCD driver output when only LCD segments
corresponding to COM4 are on.
VLCD
VLCD1, VLCD2
0V
LCD driver output when LCD segments corresponding
to COM2 and COM4 are on.
VLCD
VLCD1, VLCD2
0V
LCD driver output when all LCD segments corresponding to
COM1, COM2, COM3 and COM4 are on.
VLCD
VLCD1, VLCD2
0V
1/4 Duty, 1/2 Bias Waveforms
Note: When FC0 = 0, FC1 = 0, and FC2 = 0 in the control data
f0 =
When FC0 = 0, FC1 = 0, and FC2 = 1 in the control data
f0 =
When FC0 = 0, FC1 = 1, and FC2 = 0 in the control data
f0 =
When FC0 = 0, FC1 = 1, and FC2 = 1 in the control data
f0 =
When FC0 = 1, FC1 = 0, and FC2 = 0 in the control data
f0 =
fosc
768
fosc
576
fosc
384
fosc
288
fosc
192
=
=
=
=
=
fCK
768
fCK
576
fCK
384
fCK
288
fCK
192
No. 7980-23/39
LC75857E, LC75857W
1/4 Duty, 1/3 Bias Drive Technique
fo[Hz]
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
VLCD
VLCD1
VLCD2
0V
COM1
COM2
COM3
COM4
LCD driver output when all LCD segments corresponding to
COM1, COM2, COM3 and COM4 are turned off.
LCD driver output when only LCD segments
corresponding to COM1 are on.
LCD driver output when only LCD segments
corresponding to COM2 are on.
LCD driver output when LCD segments corresponding
to COM1 and COM2 are on.
LCD driver output when only LCD segments
corresponding to COM3 are on.
LCD driver output when LCD segments corresponding
to COM1 and COM3 are on.
LCD driver output when LCD segments corresponding
to COM2 and COM3 are on.
LCD driver output when LCD segments corresponding
to COM1, COM2 and COM3 are on.
LCD driver output when only LCD segments
corresponding to COM4 are on.
LCD driver output when LCD segments corresponding
to COM2 and COM4 are on.
LCD driver output when all LCD segments corresponding to
COM1, COM2, COM3 and COM4 are on.
1/4 Duty, 1/3 Bias Waveforms
Note: When FC0 = 0, FC1 = 0, and FC2 = 0 in the control data
f0 =
When FC0 = 0, FC1 = 0, and FC2 = 1 in the control data
f0 =
When FC0 = 0, FC1 = 1, and FC2 = 0 in the control data
f0 =
When FC0 = 0, FC1 = 1, and FC2 = 1 in the control data
f0 =
When FC0 = 1, FC1 = 0, and FC2 = 0 in the control data
f0 =
fosc
768
fosc
576
fosc
384
fosc
288
fosc
192
=
=
=
=
=
fCK
768
fCK
576
fCK
384
fCK
288
fCK
192
No. 7980-24/39
LC75857E, LC75857W
Voltage Detection Type Reset Circuit (VDET)
This circuit generates an output signal and resets the system when logic block power is first applied and when the voltage
drops, i.e., when the logic block power supply voltage is less than or equal to the power down detection voltage VDET,
which is 2.2V, typical. To assure that this function operates reliably, a capacitor must be added to the logic block power
supply line so that the logic block power supply voltage VDD rise time when the logic block power is first applied and the
logic block power supply voltage VDD fall time when the voltage drops are both at least 1 ms. (See Figure 5 and Figure 6.)
Power Supply Sequence
The following sequences must be observed when power is turned on and off. (See Figure 5 and Figure 6.)
• Power on :Logic block power supply(VDD) on → LCD driver block power supply(VLCD) on
• Power off:LCD driver block power supply(VLCD) off → Logic block power supply(VDD) off
However, if the logic and LCD driver block use a shared power supply, then the power supplies can be turned on and off
at the same time.
System Reset
The LC75857E/W supports the reset methods described below. When a system reset is applied, display is turned off, key
scanning is stopped, and all the key data is reset to low. When the reset is cleared, display is turned on and key scanning
become possible.
1. Reset methods
If at least 1 ms is assured as the logic block supply voltage VDD rise time when logic block power is applied, a system
reset will be applied by the VDET output signal when the logic block supply voltage is brought up. If at least 1 ms is
assured as the logic block supply voltage VDD fall time when logic block power drops, a system reset will be applied
in the same manner by the VDET output signal when the supply voltage is lowered. Note that the reset is cleared at
the point when all the serial data (1/3 duty: the display data D1 to D126 and the control data, 1/4 duty: the display
data D1 to D164 and the control data) has been transferred, i.e., on the fall of the CE signal on the transfer of the last
direction data, after all the direction data has been transferred. (See Figure 5 and Figure 6.)
No. 7980-25/39
LC75857E, LC75857W
• 1/3 duty
t1 t2
t3 t4
VDD
VDET
VDET
VLCD
Internal data
CE
D1 to D42, SP,
KC0 to KC2, KSC, K0,
K1,P0 to P2, SC, DR,
DT, FC0 to FC2, OC
VIL1
Display and control data transfer
Undefined
Defined
Undefined
Internal data (D43 to D84)
Undefined
Defined
Undefined
Internal data (D85 to D126)
Undefined
Defined
Undefined
System reset period
Note: t1 ≥ 1 [ms] (Logic block power supply voltage VDD rise time)
t2 ≥ 0
t3 ≥ 0
t4 ≥ 1 [ms] (Logic block power supply voltage VDD fall time)
Figure 5
• 1/4 duty
t1 t2
t3 t4
VDD
VDET
VDET
VLCD
CE
D1 to D44, SP,
KC0 to KC2, KSC, K0,
Internal data K1, P0 to P2, SC, DR,
DT,FC0 to FC2, OC
Internal data (D45 to D84)
VIL1
Display and control data transfer
Defined
Undefined
Undefined
Defined
Undefined
Internal data (D85 to D124)
Undefined
Defined
Undefined
Internal data (D125 to D164)
Undefined
Defined
Undefined
Undefined
System reset period
Note: t1 ≥ 1 [ms] (Logic block power supply voltage VDD rise time)
t2 ≥ 0
t3 ≥ 0
t4 ≥ 1 [ms] (Logic block power supply voltage VDD fall time)
Figure 6
No. 7980-26/39
LC75857E, LC75857W
2. LC75857E/W internal block states during the reset period
• CLOCK GENERATOR
A reset is applied and either the OSC pin oscillator is stopped or external clock input is stopped.
• COMMON DRIVER, SEGMENT DRIVER & LATCH
Reset is applied and the display is turned off. However, display data can be input to the latch circuit in this state.
• KEY SCAN
Reset is applied, the circuit is set to the initial state, and at the same time the key scan operation is disabled.
• KEY BUFFER
Reset is applied and all the key data is set to low.
S1/P1
S2/P2
S3/P3
S5
S4/P4
S38
COM4/S39
COM3
COM2
COM1
• CCB INTERFACE, CONTROL REGISTER, SHIFT REGISTER
Since serial data transfer is possible, these circuits are not reset.
VLCD
SEGMENT DRIVER & LATCH
VLCD1
COMMON
DRIVER
VLCD2
VSS
TEST
CLOCK
GENERATOR
OSC
CONTROL
REGISTER
DO
SHIFT REGISTER
CCB
INTERFACE
DI
CL
KEY BUFFER
CE
VDD
KS6
KS5
KS4
S42/KS3
S41/KS2
S40/KS1
KEY SCAN
KI5
KI4
KI3
KI2
KI1
VDET
Blocks that are reset
No. 7980-27/39
LC75857E, LC75857W
3. Pin states during the reset period
pin
State during reset
S1/P1 to S4/P4
L *5
S5 to S38
L
COM1 to COM3
L
COM4/S39
L *6
KS1/S40 to KS3/S42
L *5
KS4 to KS6
L *7
OSC
Z *8
DO
H *9
Notes:*5. These output pins are forcibly set to the segment output function and held low.
*6. When power is first applied, this output pin is forcibly set to the common output function and held low. However, when the DT control data bit is
transferred, either the common output or the segment output function is selected.
*7. This output pin is forcibly held fixed at the low level.
*8. This I/O pin is forcibly set to the high-impedance state.
*9. Since this output pin is an open-drain output, a pull-up resistor of between 1 and 10 kΩ is required. This pin remains high during the reset period
even if a key data read operation is performed.
Notes on the OSC Pin Peripheral Circuit
1. RC oscillator mode (control data bit OC = 0)
When RC oscillator mode is selected, the external resistor Rosc and the external capacitor Cosc must be connected
between the OSC pin and ground.
OSC
Rosc
Cosc
2. External clock mode (control data bit OC = 1)
When external clock mode is selected, the current protection resistor Rg (4.7 to 47 kΩ) must be connected between
the OSC pin and the external clock output pin (external oscillator). The value of this resistor is determined by the
allowable current for the external clock output pin. Verify that the external clock waveform is not deformed
significantly.
External clock
output pin
OSC
Rg
External oscillator
Note: The external clock output pin allowable current must be greater than VDD/Rg.
No. 7980-28/39
LC75857E, LC75857W
Sample Application Circuit 1
1/3 duty, 1/2 bias (for use with normal panels)
OSC
*11
VDD
+3V
*10
VSS
TEST
VLCD
+5V
VLCD1
VLCD2
C ≥ 0.047 µF
CE
CL
DI
DO
From the controller
To the controller
To the controller
power supply
C
KKKKK
I I I I I
54321
COM1
COM2
COM3
P1/S1
P2/S2
P3/S3
P4/S4
S5
S38
COM4/S39
SSS
444
210
/ / /
KKKKKK
SSSSSS
654321
(S40)
(S41)
(S42)
(general-purpose output ports)
Used with the backlight
controller or other circuit.
LCD panel (up to 126 segments)
(P1)
(P2)
(P3)
(P4)
*12
Key matrix
(up to 30 keys)
Notes:*10. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic
block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75857E/W is reset by the VDET.
*11. When RC oscillator mode is used, the external resistor Rosc and the external capacitor Cosc must be connected between the OSC pin and
ground, and when external clock mode is selected the current protection resistor Rg (4.7 to 47 kΩ) must be connected between the OSC pin and
the external clock output pin (external oscillator). (See the section on the OSC pin peripheral circuit.)
*12. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of
the external wiring so that signal waveforms are not degraded.
No. 7980-29/39
LC75857E, LC75857W
Sample Application Circuit 2
1/3 duty, 1/2 bias (for use with large panels)
OSC
*11
VDD
+3V
*10
VSS
TEST
10 kΩ ≥ R ≥ 1 kΩ
C ≥ 0.047 µF
VLCD
+5V
R
C
VLCD2
S38
COM4/S39
CE
CL
DI
DO
From the controller
To the controller
To the controller
power supply
R
VLCD1
COM1
COM2
COM3
P1/S1
P2/S2
P3/S3
P4/S4
S5
KKKKK
I I I I I
54321
SSS
444
210
/ / /
KKKKKK
SSSSSS
654321
(S40)
(S41)
(S42)
(general-purpose output ports)
Used with the backlight
controller or other circuit.
LCD panel (up to 126 segments)
(P1)
(P2)
(P3)
(P4)
*12
Key matrix
(up to 30 keys)
Notes:*10. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic
block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75857E/W is reset by the VDET.
*11. When RC oscillator mode is used, the external resistor Rosc and the external capacitor Cosc must be connected between the OSC pin and
ground, and when external clock mode is selected the current protection resistor Rg (4.7 to 47 kΩ) must be connected between the OSC pin and
the external clock output pin (external oscillator). (See the section on the OSC pin peripheral circuit.)
*12. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of
the external wiring so that signal waveforms are not degraded.
No. 7980-30/39
LC75857E, LC75857W
Sample Application Circuit 3
1/3 duty, 1/3 bias (for use with normal panels)
OSC
*11
VDD
+3V
*10
VSS
TEST
VLCD
+5V
VLCD1
VLCD2
C ≥ 0.047 µF
C
CE
CL
DI
DO
From the controller
To the controller
To the controller
power supply
C
KKKKK
I I I I I
54321
COM1
COM2
COM3
P1/S1
P2/S2
P3/S3
P4/S4
S5
S38
COM4/S39
SSS
444
210
/ / /
KKKKKK
SSSSSS
654321
(S40)
(S41)
(S42)
(general-purpose output ports)
Used with the backlight
controller or other circuit.
LCD panel (up to 126 segments)
(P1)
(P2)
(P3)
(P4)
*12
Key matrix
(up to 30 keys)
Notes:*10. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic
block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75857E/W is reset by the VDET.
*11. When RC oscillator mode is used, the external resistor Rosc and the external capacitor Cosc must be connected between the OSC pin and
ground, and when external clock mode is selected the current protection resistor Rg (4.7 to 47 kΩ) must be connected between the OSC pin and
the external clock output pin (external oscillator). (See the section on the OSC pin peripheral circuit.)
*12. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of
the external wiring so that signal waveforms are not degraded.
No. 7980-31/39
LC75857E, LC75857W
Sample Application Circuit 4
1/3 duty, 1/3 bias (for use with large panels)
OSC
*11
VDD
+3V
*10
VSS
TEST
10 kΩ ≥ R ≥ 1 kΩ
C ≥ 0.047 µF
VLCD
+5V
R
VLCD1
R
C
VLCD2
R
CE
CL
DI
DO
From the controller
To the controller
To the controller
power supply
C
KKKKK
I I I I I
54321
COM1
COM2
COM3
P1/S1
P2/S2
P3/S3
P4/S4
S5
S38
COM4/S39
SSS
444
210
/ / /
KKKKKK
SSSSSS
654321
(S40)
(S41)
(S42)
(general-purpose output ports)
Used with the backlight
controller or other circuit.
LCD panel (up to 126 segments)
(P1)
(P2)
(P3)
(P4)
*12
Key matrix
(up to 30 keys)
Notes:*10. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic
block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75857E/W is reset by the VDET.
*11. When RC oscillator mode is used, the external resistor Rosc and the external capacitor Cosc must be connected between the OSC pin and
ground, and when external clock mode is selected the current protection resistor Rg (4.7 to 47 kΩ) must be connected between the OSC pin and
the external clock output pin (external oscillator). (See the section on the OSC pin peripheral circuit.)
*12. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of
the external wiring so that signal waveforms are not degraded.
No. 7980-32/39
LC75857E, LC75857W
Sample Application Circuit 5
1/4 duty, 1/2 bias (for use with normal panels)
OSC
*11
VDD
+3V
*10
VSS
TEST
VLCD
+5V
VLCD1
VLCD2
C ≥ 0.047 µF
To the controller
To the controller
power supply
C
S38
CE
CL
DI
DO
From the controller
COM1
COM2
COM3
S39/COM4
P1/S1
P2/S2
P3/S3
P4/S4
S5
KKKKK
I I I I I
54321
SSS
444
210
/ / /
KKKKKK
SSSSSS
654321
(S40)
(S41)
(S42)
(general-purpose output ports)
Used with the backlight
controller or other circuit.
LCD panel (up to 164 segments)
(P1)
(P2)
(P3)
(P4)
*12
Key matrix
(up to 30 keys)
Notes:*10. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic
block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75857E/W is reset by the VDET.
*11. When RC oscillator mode is used, the external resistor Rosc and the external capacitor Cosc must be connected between the OSC pin and
ground, and when external clock mode is selected the current protection resistor Rg (4.7 to 47 kΩ) must be connected between the OSC pin and
the external clock output pin (external oscillator). (See the section on the OSC pin peripheral circuit.)
*12. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of
the external wiring so that signal waveforms are not degraded.
No. 7980-33/39
LC75857E, LC75857W
Sample Application Circuit 6
1/4 duty, 1/2 bias (for use with large panels)
+3V
OSC
*11
VDD
*10
VSS
TEST
10 kΩ ≥ R ≥ 1 kΩ
C ≥ 0.047 µF
VLCD
+5V
R
C
R
VLCD1
VLCD2
COM1
COM2
COM3
S39/COM4
P1/S1
P2/S2
P3/S3
P4/S4
S5
S38
CE
CL
DI
DO
From the controller
To the controller
To the controller
power supply
KKKKK
I I I I I
54321
SSS
444
210
/ / /
KKKKKK
SSSSSS
654321
(S40)
(S41)
(S42)
(general-purpose output ports)
Used with the backlight
controller or other circuit.
LCD panel (up to 164 segments)
(P1)
(P2)
(P3)
(P4)
*12
Key matrix
(up to 30 keys)
Notes:*10. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic
block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75857E/W is reset by the VDET.
*11. When RC oscillator mode is used, the external resistor Rosc and the external capacitor Cosc must be connected between the OSC pin and
ground, and when external clock mode is selected the current protection resistor Rg (4.7 to 47 kΩ) must be connected between the OSC pin and
the external clock output pin (external oscillator). (See the section on the OSC pin peripheral circuit.)
*12. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of
the external wiring so that signal waveforms are not degraded.
No. 7980-34/39
LC75857E, LC75857W
Sample Application Circuit 7
1/4 duty, 1/3 bias (for use with normal panels)
OSC
*11
VDD
+3V
*10
VSS
TEST
VLCD
+5V
VLCD1
C ≥ 0.047 µF
VLCD2
C
To the controller
To the controller
power supply
C
S38
CE
CL
DI
DO
From the controller
COM1
COM2
COM3
S39/COM4
P1/S1
P2/S2
P3/S3
P4/S4
S5
KKKKK
I I I I I
54321
SSS
444
210
/ / /
KKKKKK
SSSSSS
654321
(S40)
(S41)
(S42)
(general-purpose output ports)
Used with the backlight
controller or other circuit.
LCD panel (up to 164 segments)
(P1)
(P2)
(P3)
(P4)
*12
Key matrix
(up to 30 keys)
Notes:*10. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic
block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75857E/W is reset by the VDET.
*11. When RC oscillator mode is used, the external resistor Rosc and the external capacitor Cosc must be connected between the OSC pin and
ground, and when external clock mode is selected the current protection resistor Rg (4.7 to 47 kΩ) must be connected between the OSC pin and
the external clock output pin (external oscillator). (See the section on the OSC pin peripheral circuit.)
*12. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of
the external wiring so that signal waveforms are not degraded.
No. 7980-35/39
LC75857E, LC75857W
Sample Application Circuit 8
1/4 duty, 1/3 bias (for use with large panels)
OSC
*11
VDD
+3V
*10
COM1
COM2
COM3
S39/COM4
P1/S1
P2/S2
P3/S3
P4/S4
S5
VSS
TEST
10 kΩ ≥ R ≥ 1 kΩ
C ≥ 0.047 µF
VLCD
+5V
R
VLCD1
R
C
VLCD2
R
S38
CE
CL
DI
DO
From the controller
To the controller
To the controller
power supply
C
KKKKK
I I I I I
54321
SSS
444
210
/ / /
KKKKKK
SSSSSS
654321
(S40)
(S41)
(S42)
(general-purpose output ports)
Used with the backlight
controller or other circuit.
LCD panel (up to 164 segments)
(P1)
(P2)
(P3)
(P4)
*12
Key matrix
(up to 30 keys)
Notes:*10. Add a capacitor to the logic block power supply line so that the logic block power supply voltage VDD rise time when power is applied and the logic
block power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75857E/W is reset by the VDET.
*11. When RC oscillator mode is used, the external resistor Rosc and the external capacitor Cosc must be connected between the OSC pin and
ground, and when external clock mode is selected the current protection resistor Rg (4.7 to 47 kΩ) must be connected between the OSC pin and
the external clock output pin (external oscillator). (See the section on the OSC pin peripheral circuit.)
*12. The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 kΩ) appropriate for the capacitance of
the external wiring so that signal waveforms are not degraded.
Notes on transferring display data from the controller
When using the LC75857E/W in 1/3 duty, applications transfer the display data (D1 to D126) in three operations, and in
1/4 duty, they transfer the display data (D1 to D164) in four operations. In either case, applications should transfer all of
the display data within 30 ms to maintain the quality of the displayed image.
No. 7980-36/39
LC75857E, LC75857W
Notes on the controller key data read techniques
1. Timer based key data acquisition
(1) Flowchart
CE = [L]
NO
DO = [L]
YES
Key data read
processing
(2) Timing chart
Key on
Key on
Key input
Key scan
t5
t6
t5
t5
CE
t8
t8
t8
Key address
DI
t7
Key data read
t7
t7
DO
Key data read request
t9
Controller
determination
(Key on)
t9
Controller
determination
(Key on)
t9
Controller
determination
(Key off)
t9
Controller
determination
(Key on)
Controller
determination
(Key off)
t5: Key scan execution time when the key data agreed for two key scans. (615T(s))
t6: Key scan execution time when the key data did not agree for two key scans and the key scan was executed again. (1230T(s))
t7: Key address (43H) transfer time
1
1
T =——— = ——
t8: Key data read time
fosc
fCK
(3) Explanation
In this technique, the controller uses a timer to determine key on/off states and read the key data. The controller must
check the DO state when CE is low every t9 period without fail. If DO is low, the controller recognizes that a key has
been pressed and executes the key data read operation.
The period t9 in this technique must satisfy the following condition.
t9>t6+t7+t8
If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge
data (SA) will be invalid.
No. 7980-37/39
LC75857E, LC75857W
2. Interrupt based key data acquisition
(1) Flowchart
CE = [L]
NO
DO = [L]
YES
Key data read
processing
Wait for at
least t10
CE = [L]
NO
DO = [H]
YES
Key OFF
(2) Timing chart
Key on
Key on
Key input
Key scan
t5
t5
t6
t5
CE
t8
t8
t8
t8
Key address
DI
t7
Key data read
t7
t7
t7
DO
Key data read request
t10
Controller
determination
(Key on)
Controller
determination
(Key off)
t10
Controller
determination
(Key on)
Controller
determination
(Key on)
t10
Controller
determination
(Key on)
t10
Controller
determination
(Key off)
t5: Key scan execution time when the key data agreed for two key scans. (615T(s))
t6: Key scan execution time when the key data did not agree for two key scans and the key scan was executed again. (1230T(s))
t7: Key address (43H) transfer time
1
1
T =——— = ——
t8: Key data read time
fosc
fCK
No. 7980-38/39
LC75857E, 75857W
(3) Explanation
In this technique, the controller uses interrupts to determine key on/off states and read the key data. The controller
must check the DO state when CE is low. If DO is low, the controller recognizes that a key has been pressed and
executes the key data read operation. After that the next key on/off determination is performed after the time t10
has elapsed by checking the DO state when CE is low and reading the key data. The period t10 in this technique
must satisfy the following condition.
t10 > t6
If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge
data (SA) will be invalid.
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts.
SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as
components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any
such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.7980-39/39