HS-26CT32RH Data Sheet October 1999 Radiation Hardened Quad Differential Line Receiver tle T3 ) - The Intersil HS-26CT32RH is a differential line receiver designed for digital data transmission over balanced lines and meets the requirements of EIA standard RS-422. Radiation hardened CMOS processing assures low power consumption, high speed, and reliable operation in the most severe radiation environments. File Number 2930.3 Features • Electrically Screened to SMD # 5962-95631 • QML Qualified per MIL-PRF-38535 Requirements • 1.2 Micron Radiation Hardened CMOS - Total Dose . . . . . . . . . . . . . . . . . . . .Up to 300kRAD(Si) • Latchup Free • EIA RS-422 Compatible Outputs iadd eral eiv tho ds r- The HS-26CT32RH has an input sensitivity typically of 200mV over the common mode input voltage range of ±7V. The receivers are also equipped with input fail safe circuitry, which causes the outputs to go to a logic “1” when the inputs are open. Enable and Disable functions are common to all four receivers. Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed here must be used when ordering. Detailed Electrical Specifications for these devices are contained in SMD 5962-95631. A “hot-link” is provided on our homepage for downloading. http://www.intersil.com/spacedefense/space.htm ENABLE ENABLE DIN DIN CIN CIN BIN BIN AIN AIN - + + + DOUT • Low Power Dissipation Standby (Max). . . . . . . . . .138mW • Single 5V Supply • Full Military Temperature Range . . . . . . . -55oC to 125oC Pinouts HS1-26CT32RH (SBDIP) CDIP2-T16 TOP VIEW AIN 1 16 VDD AIN 2 15 BIN AOUT 3 14 BIN ENABLE 4 13 BOUT - COUT - BOUT - 12 ENABLE CIN 6 11 DOUT CIN 7 10 DIN GND 8 9 DIN AOUT HS9-26CT32RH (FLATPACK) CDFP4-F16 TOP VIEW Ordering Information ORDERING NUMBER 5962F9563101QEC , • High Impedance Inputs when Disabled or Powered Down COUT 5 + or, ia- d, L, l- • Input Fail Safe Circuitry Logic Diagram pon, i- d, • TTL Compatible Inputs INTERNAL MKT. NUMBER HS1-26CT32RH-8 TEMP. RANGE (oC) -55 to 125 AIN 1 16 VDD AIN 2 15 BIN AOUT 3 14 BIN ENABLE 4 13 BOUT 5962F9563101QXC HS9-26CT32RH-8 -55 to 125 COUT 5 12 ENABLE 5962F9563101V9A HS0-26CT32RH-Q 25 CIN 6 11 DOUT -55 to 125 CIN 7 10 DIN GND 8 9 DIN 5962F9563101VEC 5962F9563101VXC HS1-26CT32RH-Q HS9-26CT32RH-Q -55 to 125 HS1-26CT32RH/PROTO HS1-26CT32RH/PROTO -55 to 125 HS9-26CT32RH/PROTO HS9-26CT32RH/PROTO -55 to 125 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 2000 HS-26CT32RH Die Characteristics DIE DIMENSIONS: Backside Finish: 84 mils x 130 mils (2140µm x 3290µm) Silicon ASSEMBLY RELATED INFORMATION: INTERFACE MATERIALS: Substrate Potential: Glassivation: VDD (When Powered Up) Type: PSG (Phosphorus Silicon Glass) Thickness: 10kÅ ±1kÅ ADDITIONAL INFORMATION: Worst Case Current Density: Top Metallization: <2.0 x 105A/cm2 M1: Mo/Tiw Thickness: 5800Å M2: Al/Si/Cu Thickness: 10kÅ ±1kÅ Transistor Count: 240 Bond Pad Size: Substrate: 110µm x 100µm AVLSI1RA Metallization Mask Layout HS-26CT32RH AIN (1) VDD (16) BIN (15) (14) BIN AIN (2) (13) BOUT AOUT (3) ENAB (4) (12) ENAB COUT (5) (11) DOUT (10) DIN CIN (6) (7) CIN (8) GND (9) DIN All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com 2