DC-AC INVERTER UNIT PS-DA0201-125(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC/AC inverter is developed for dual lamps. Optimized for Chi Mei: G121X1-L01 APPLICABLE LCD: 6.4 to 18 inches double lamps Lamp voltage 500 Vrms Lamp current 2 x 8 mArms Lamp Start Up Voltage 1.500 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Open lamp detection Special fuse Bourns SF1206 Series 2A RoHS compliant (S) High efficiency TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH -30°C ~ +65°C -40°C ~ +85°C 95 %RH max 160 x 25 x 10 mm Unit : mm Weight :24,2 (g) typ. Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 3 Part Description PCB Connector CN1 Connector CN2 + CN3 Input side CN1: Pin No. Symbols Vin CN 1-1 GND CN 1-2 Vrm t CN 1-3 Vbr CN 1-4 CN 1-5 Qty. 1 1 2 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-K SM02(8.0)B-BHS-1-TB Ratings 12 Vdc 0 ~ 0.4 = OFF / 2.5 ~ Vin = ON 0 ~ 5.0 Vdc N.C. Note t=1m m JST or equal JST or equal Output side CN2 + CN3: Pin No. Symbols Ratings VHIGH1 500 Vrm s (8 m Arm s ) CN 2-1 N.C. CN 2-2 VLOW GND CN 2-3 - Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 2.2.1, 21th May 2014 DC-AC INVERTER UNIT PS-DA0201-125(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage No load Shutdow n Iout Iout Iin F Vopen Ts d Note 1 : Note 2 : Vin (V) Vbr (V) 12±1.2 12±0.6 12±1.2 12±1.2 11.4 12±1.2 0.0 5.0 0.0 0.0 0.0 0.0 Specification Tu (°C) -30 -30 -30 -30 -30 -30 ~ +65 ~ +65 ~ +65 ~ +65 ~ +65 ~ +65 Min. Typ. Max. 7.5 45 1.300 - 8.0 30 0.88 50 1.500 1.0 8.5 1.2 55 1.900 - Unit Note m Arm s % Adc kHz Vrm s s ec Dut y 9 5% Dut y M in wit ho ut lo ad Please keep a minimum of 2mm clearance in all directions between inverter high voltage areas and any conductors. The inverter has a small diming function of 5% to prevent flickering problem caused by this panel. TEST CIRCUIT : SW 1 Operation of unit a Operation b Non operation Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 2.2.1, 21th May 2014