DC-AC INVERTER UNIT PS-DA0201-137(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC/AC inverter is developed for dual lamps. Optimized for Chi Mei: G121X1-L01 and G150X1-L01 APPLICABLE LCD: 6.4 to 18 inches double lamps Lamp voltage 580 Vrms Lamp current 2 x 8 mArms Lamp Start Up Voltage 1.500 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Open lamp detection Wide dimming range High efficiency RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH -30°C ~ +70°C -40°C ~ +85°C 95 %RH max 160 x 25 x 10 mm Pin 1 Pin 1 Pin 1 Unit : mm Weight :24,2 (g) typ. Pin 1 Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 3 Part Description PCB Connector CN1 Connector CN2 + CN3 Input side CN1: Pin No. Symbols Vin CN 1-1 GND CN 1-2 Vrm t CN 1-3 Vbr CN 1-4 CN 1-5 Qty. 1 1 2 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-K SM02(8.0)B-BHS-1-TB Ratings 12 Vdc 0 ~ 0.4 = OFF / 2.5 ~ Vin = ON 0 ~ 2.5 Vdc N.C. Note t=1m m JST or equal JST or equal Output side CN2 + CN3: Pin No. Symbols Ratings VHIGH 580 Vrm s (8 m Arm s ) CN 2-1 N.C. CN 2-2 VLOW GND CN 2-3 - Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 2.0.1, 21st May 2014 DC-AC INVERTER UNIT PS-DA0201-137(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage No load Shutdown Note 1 : Specification Vin (V) Vbr (V) Tu (°C) Iout Iout Iin F Vopen 12±1.2 12±0.6 12±1.2 12±1.2 11.4 0.0 2.5 0.0 0.0 0.0 -30 -30 -30 -30 -30 Ts d 12±1.2 0.0 -30 ~ +70 ~ +70 ~ +70 ~ +70 ~ +70 ~ +70 Unit Note 8.5 1.2 55 1.900 m Arm s % Adc kHz Vrm s Duty 100% - s ec wit hout load Min. Typ. Max. 7.5 45 1.300 8.0 20 0.88 50 1.500 - 1.0 Dut y M in Please keep a minimum of 2mm clearance in all directions between inverter high voltage areas and any conductors. TEST CIRCUIT : SW 1 Operation of unit a Operation b Non operation Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 2.0.1, 21st May 2014