DC-AC INVERTER UNIT PS-DA0144-01(S) (5W SINGLE OUTPUT) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for single lamp. APPLICABLE LCD: 6,4 to 12 inches single lamp type Lamp Voltage 690 Vrms Lamp Current 5 mArms Lamp Start Up Voltage 1.700 Vrms (Vin : 5 Vdc) FEATURES : Remote ON/OFF RoHS compliant (S) Wide Dimming Function with intern PWM controller TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxW xH -10°C ~ +50°C -20°C ~ +85°C 95 %RH max 95.5 x 30 x 9,5 mm Unit : mm Weight :20 (g) typ. Components No. 1 2 3 Note: Please use plastic screw in case of a non-insulating mounting base! Part Description PCB Connector CN1 Connector CN2 Input side CN1: Pin No. Symbols CN 1-1 Vin CN 1-2 CN 1-3 GND CN 1-4 Vrm t CN 1-5 Vbr CN 1-6 Qty. 1 1 1 Ratings 4.75 ~ 5.25V 0V Material UL94V-0 (CEM-3) 53261-0690 SM02(8.0)B-BHS-1-TB Output side CN2: Pin No. Symbols Vlow CN 2-1 N.C. CN 2-2 Vhigh CN 2-3 Note t=1.0m m MOLEX JST Ratings 2V 690Vrms (5mArms) 0~0.4V=OFF / 2.5V~Vin=ON 0 ~ 5V Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.1.2, 31th August 2010 DC-AC INVERTER UNIT PS-DA0144-01(S) (5W SINGLE OUTPUT) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage No Load Shutdown Iout Iout Iin F1 Vopen Tsd Note 1 : Note 2: Note 3: Vin (V) 5±0.05 5±0.5 5±0.5 5±0.5 4,75 5±0.5 Conditions Vrmt (V) 0 5.0 0 0 0 0 Tu (°C) -10~+50 -10~+50 -10~+50 -10~+50 -10~+50 -10~+50 Specification Min. Typ. Max. 4.5 5.0 5.5 20 0.97 1.30 40 50 60 1.500 1.700 2000 1.0 - Unit Note mArms % Adc kHz Vrms sec. Duty 100% Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Open circuit on all lamps for more than 1 sec. Before apply any control signal into inverter, please provide Vcc first. Please follow the reversed sequence during power off. Power off control signal first, then power off Vcc. TEST CIRCUIT : SW 1 Operation of unit a Operation b Non operation Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.1.2, 31th August 2010