DC-AC INVERTER UNIT PS-DA0408-359(S) (18 W QUAD OUTPUTS) DESCRIPTION : This low profile DC/AC Inverter is developed for quad lamps. Optimized for Chi Mei: G154I1-L01 APPLICABLE LCD: 15 to 17 inches quad lamps Lamp voltage 600 Vrms Lamp current 4 x 7.0 mArms Lamp start up voltage 1.570 Vrms min. (Vin : 10.8 Vdc) FEATURES : Remote ON/OFF Independent open lamp detection for each side PWM dimming Current feedback circuit RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating temperature range -10°C ~ +70°C Storage temperature range-20°C ~ +85°C Humidity 95 %RH max DIMENSIONS : LxWxH 160 x 26 x 12 mm Pin 1 Pin 1 Pin 1 Pin 1 Pin 1 Unit : mm Weight :40 (g) typ. Pin 1 Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 3 Part Description PCB Connector CN1 Connector CN2 ~ CN5 Input side CN1: Pin No. CN 1-1;3;5;6;8;9 CN 1-2 Symbols GND Vbr CN 1-4 Vrmt CN 1-7 CN 1-10;11;12 N.C. Vin Qty. 1 1 4 Material UL94V-0 (FR-4 or CEM-3) 53261-1290 P35J1L-02SMTH(LF)(SN) Manufacturer Top Ever Sun Molex or equal JST or equal Output side CN2 ~ CN5 Ratings Pin No. CN 2-1 CN 2-2 0 ~ 5.0 Vdc 0 ~ 0.5 = OFF / 4.5 ~ Vin = ON Symbols Vhigh Vlow Ratings 600 Vrms (7.0 mArms) (GND) 10.8 ~ 13.2 Vdc Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0.7, 19th May 2014 DC-AC INVERTER UNIT PS-DA0408-359(S) (18 W QUAD OUTPUTS) ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage Iout Iout Iin F Vopen Note 1 : Note 2: Specification Vin (V) Vbr (V) Tu (°C) Min. Typ. Max. 12±1.2 12±1.2 12±1.2 12±1.2 12±1.2 0 5.0 0 0 0 -10 ~ +70 -10 ~ +70 -10 ~ +70 -10 ~ +70 -10 ~ +70 6.4 45 1.570 7.0 23 1.61 50 1.700 7.6 2.09 55 2.300 Unit Note mArms % Adc kHz Vrms Duty 100% Please keep a minimum of 2mm clearance in all directions between inverter high voltage areas and any conductors as marked on mechanical drawing. Please provide Vcc before applying any control signals into inverter. Revere the sequence during power off which is control signal off first then Vcc. TEST CIRCUIT : SW 1 Operation of unit a Operation b Non operation Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0.7, 19th May 2014