CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 1 of 33 DATE 29.05.2009 Datum Specification for Production Applicant / Manufacturer Hardware Panasonic Electronic Devices Europe GmbH Zeppelinstrasse 19 21337 Lüneburg Germany Applicant / Manufacturer Software Software Version Stollmann Entwicklungs- und Vertriebs-GmbH Mendelssohnstrasse 15 D 22761 Hamburg Germany e.g. BlueRS+ SPP Contents Approval for Mass Production Customer By signing this document, Customer accepts the validity of the below-mentioned contents and declares his full notice to it. Some passages may be changed if required; the validity shall not be affected thereby. CHECKED / APPROVED: DATE: NAME: SIGNATURE: NOTE: AT LEAST ONE SET OF APPROVED SPECIFICATIONS SHOULD BE RETURNED TO THE ADDRESS OF THE ISSUING PARTY. PANASONIC ELECTRONIC DEVICES EUROPE GMBH High Frequency Products Business Group - Wireless Modules - APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 2 of 33 DATE 29.05.2009 Datum TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Key Features................................................................................................................... 4 Applications for the Module............................................................................................. 4 Description for the Module .............................................................................................. 5 Scope of this Document .................................................................................................. 6 History for this Document................................................................................................ 6 Terminal Layout .............................................................................................................. 7 6.1. General Pin Assignment ........................................................................................ 8 6.2. Application Specific Pin Description ...................................................................... 9 6.2.1. SPP configuration DCE Mode .................................................................. 9 Terminal Specifics......................................................................................................... 10 7.1. RF-Interface - ANT .............................................................................................. 10 7.2. Power Supply....................................................................................................... 10 7.3. Power-On-Reset .................................................................................................. 10 7.4. UART Interface – TXD, RXD, CTS, RTS ............................................................. 11 7.5. 3-wire Serial Interface.......................................................................................... 12 7.6. USB Interface, ...................................................................................................... 12 7.6.1. USB_DP, USB_DN ................................................................................ 12 7.7. GPIO Interface..................................................................................................... 12 7.8. ADC ..................................................................................................................... 12 7.9. DAC ..................................................................................................................... 12 7.10. PCM Interface...................................................................................................... 12 Key Parts List ................................................................................................................ 13 Test Conditions ............................................................................................................. 14 Absolute Maximum Ratings (1)....................................................................................... 14 Electrical Requirements ................................................................................................ 14 I/O Operating Characteristics........................................................................................ 15 USB Interface................................................................................................................ 15 Typical Current Consumption........................................................................................ 16 14.1. SPP Configuration ............................................................................................... 16 14.1.1. Deep Sleep State ................................................................................... 16 14.1.2. Power Down State.................................................................................. 16 14.1.3. Idle State ................................................................................................ 16 14.2. Power Consumption ............................................................................................ 16 14.3. Power-up time...................................................................................................... 17 Electrical RF-Characteristics......................................................................................... 17 Mechanical Requirements............................................................................................. 18 Soldering Temperature-Time Profile (for reflow soldering) ........................................... 19 17.1. For lead solder..................................................................................................... 19 17.2. For leadfree solder............................................................................................... 19 PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 3 of 33 DATE 29.05.2009 Datum Module Dimension ........................................................................................................ 20 Recommended Foot Pattern ......................................................................................... 21 Labelling Drawing.......................................................................................................... 23 Software ........................................................................................................................ 23 21.1. SPP Software ...................................................................................................... 23 21.2. HDP Software ...................................................................................................... 23 21.3. HID Software ....................................................................................................... 23 Cautions ........................................................................................................................ 24 22.1. Design Notes ....................................................................................................... 24 22.2. Installation Notes ................................................................................................. 24 22.3. Usage Conditions Notes ...................................................................................... 24 22.4. Storage Notes...................................................................................................... 25 22.5. Safety Cautions ................................................................................................... 25 22.6. Other cautions ..................................................................................................... 26 Packaging ..................................................................................................................... 27 23.1. Embossed tape / Blistergurt................................................................................. 27 23.2. Component direction............................................................................................ 28 23.3. Reel dimension .................................................................................................... 28 23.4. Package............................................................................................................... 29 Ordering Information ..................................................................................................... 30 RoHS Declaration ......................................................................................................... 30 Data Sheet Status ......................................................................................................... 30 Regulatory Information.................................................................................................. 31 27.1. FCC Notice .......................................................................................................... 31 27.2. Caution ................................................................................................................ 31 27.3. Labeling Requirements........................................................................................ 31 27.4. Antenna Warning ................................................................................................. 32 27.5. Approved Antenna List ........................................................................................ 32 27.6. RF Exposure PAN1455/PAN1555 ....................................................................... 32 27.7. Industry Canada Certification .............................................................................. 32 Related Documents....................................................................................................... 33 General Information ...................................................................................................... 33 Life Support Policy ........................................................................................................ 33 PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 4 of 33 DATE 29.05.2009 Datum 1. KEY FEATURES Schlüsseleigenschaften • • • • • • • • • • • • • • • • • • • • • • Bluetooth specification v2.0 + EDR (Enhanced Data Rate) CSR BlueCore6-ROM inside Complete Co-location and Co-existence with IEEE 802.11 (AWMA, AFH and SFH) Fast Connection Setup Extended SCO Link RF output power class 2 with power control Supply Voltage 3.0V to 3.6V Internal crystal oscillator (26MHz, 14.7456 MHz and 32 kHz for deep sleep) Surface mount type • PAN1455: 13.5 x 18.75 x 2.85 mm • PAN1555: 13.5 x 22.75 x 2.85 mm Built-in shielding to be compliant to FCC Full Bluetooth data rate up to 2178kbps asymmetric Support for all Bluetooth power saving modes (Park, Sniff, Hold) Support for very low-power modes (deep sleep and power down) Otional support for ultra-low-power mode. Standby with Battery-Backup PCM Interface Master / Slave supporting 13 or 16 bit linear, 8 bit µ-law or A-law Codecs and CVSD transcoders on up to 3 SCO channels Full 8- to 128-bit encryption High sensitivity design (-86 dBm typ.) 3 UART, USB, I2C and SPI Interface 18 GPIO’s for individual usage for your embedded software 3 Channel ADC and 1 Channel DAC Cortex-M3 ST32F103 core for embedded profiles or application software Manufactured in conformance with RoHS 2. APPLICATIONS FOR THE MODULE Applikationen für das Modul All Embedded Wireless Applications • • Access Points Printer Adapters • • • • • Printers Scanners Wireless Sensors • • • PANASONIC ELECTRONIC DEVICES EUROPE GMBH Cable Replacement Personal Digital Assistants (PDAs) Access Points Computers and Peripherals Industrial Control Applications www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 5 of 33 DATE 29.05.2009 Datum 3. DESCRIPTION FOR THE MODULE Modulbeschreibung PAN1455/1555 is a short-range class 2 module for implementing Bluetooth functionality into various electronic devices. The module consists of three major parts; a baseband controller, a EEPROM memory and a radio that operates in the license-free 2.45 GHz ISM band. Communication between the module and the host controller is carried out normally via UART. Otional via below interfaces. Please contact your local sales office for further details on additional options. PAN1455 Antenna 256K EEPROM GPIO´s Debug UART STM32 SPP-AT UART BC06ROM 256kByte Flash 48kByte RAM BALUN Filter Matching Circuit 50 Ohm PLL Optional: 2 x SPI, USB, UART, ADC, JTAG, PCM, WLANCoexistence Optional U.FL Optional 16MHz USB 14,7456MHz Optional One Crystal 14,75MHz Temp -25°C to +85°C 26MHz Optional Low Power 32KHz Oscillator Bottom Pad PAN1555 Figure 3.1 PAN1455/1555 Block-Diagram PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 6 of 33 DATE 29.05.2009 Datum 4. SCOPE OF THIS DOCUMENT Umfang dieses Dokumentes This product specification applies to the class 2 bluetooth module ENW89815C3KF/ENW89815A3KF. The different characters indicates different versions (refer to chapter 24 Ordering Information) The used bluetooth chip is the BlueCore6 from the company CSR. (www.csr.com). Diese Produktionsunterlagen beziehen sich auf das Class 2 Bluetooth Modul ENW89815C3KF/ENW89815A3KF. Die unterschiedlichen Zeichen bezeichnen verschiedene Versionen (Erklärung im Kapitel 24 Ordering Information) Der verwendete Bluetooth Chip ist der BlueCore6 der Firma CSR. 5. HISTORY FOR THIS DOCUMENT Versionsverwaltung dieses Dokumentes Revision Version Date Datum Modification / Remarks Änderungen / Bemerkungen 0.90 06.03.2009 Preliminary release. 0.91 30.03.2009 Add FCC Notice 0.92 04.05.2009 Include RF-Performance and current consumption 0.93 06.05.2009 Do minor changes in formatting, content links now included. 0.94 29.05.2009 Include final tables and Interface description PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE No. REV. DS-1x55-2400-102 0.94 PAGE Seite 7 of 33 DATE 29.05.2009 Datum ENW89815C3KF/ENW89815A3KF 6. TERMINAL LAYOUT Anschlußbelegung 10 9 8 7 6 5 4 3 2 11 1 1 34 12 33 13 32 14 31 15 30 16 17 18 19 20 21 22 23 24 25 B A D C 29 28 26 27 Figure 6.1 PAN1455/1555 Pin Numbering Bottom View 10 9 8 7 6 5 4 3 2 11 1 1 34 12 33 13 32 14 31 15 30 17 18 19 20 21 22 23 24 25 B A D C 26 29 ANT 16 28 27 Figure 6.2 PAN1455/1555 Pin Numbering Bottom View PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 8 of 33 DATE 29.05.2009 Datum 6.1. GENERAL PIN ASSIGNMENT No Pin Name Type PU/PD Active Description 1 2 3 4 5 6 7 GND1 ANT UART_RTS# UART_TXD UART_RXD UART_CTS# GPIO[9]/PCM_CLK P I/O I I O O I/O PD PD PU H L L H L 8 GPIO[10]/PCM_O/TXD3 I/O PU L 9 GPIO[7]/PCM_SYNC I/O PD H 10 11 GND2 ATRST/SPI2_MISO P I/O PU H 12 GPIO[8]/PCM_I/RXD3 I/O PU L 13 ATDI/SPI2_CS I/O PU - 14 15 16 17 18 19 ATMS reserved VCC RESET# GND3 GPIO[14] I I P I P I/O PU PD PU PU L L 20 GPIO[13] I/O PD H 21 GPIO[15] I/O PU L 22 GPIO[6]/ADC I/O PD H 23 24 25 ATDO/SPI2_SCK ATCK GPIO[3]/SPI_CLK O O I/O PU PD PD H 26 GPIO[0]/SPI_MOSI I/O PD H 27 28 GND4 GPIO[2]/SPI_CS P I/O PD H 29 GPIO[1]/SPI_MISO I/O PD H 30 GPIO[5]/TXD2 I/O PD H 31 GPIO[4]/RXD2 I/O PD H 32 33 34 USB_DM USB_DP GPIO[17]/TAMPER I/O I/O I/O PD PD PD - A GPIO[16]/SPI2_MOSI I/O PU L B GPIO[12]/I2C_SCL I/O PU L C GPIO[11]/I2C_SDA I/O PU L D VBAT P - - Connect to Ground Antenna Connector UART Request To Send (active low) UART Data Input, weak internal Pull-Down UART Data Output UART Clear To Send, internal Pull-Up General Purpose Input/Output, weak internal PullUp / PCM Data Clock Output General Purpose Input/Output, weak internal PullUp / PCM Data Output/ UART3 DATA Output General Purpose Input/Output, weak internal PullDown / PCM Data Sync Output Connect to Ground JTAG reset, internal Pull-Up / SPI2 Master In Slave Out General Purpose Input/Output, weak internal PullUp / PCM Data Input / UART3 DATA Input JTAG test data input, weak internal Pull-Up / SPI2 Chip Select JTAG mode select, weak internal Pull-Up for Debug-Use only, nc VCC Reset input Connect to Ground General Purpose Input/Output, weak internal PullUp General Purpose Input/Output, weak internal PullDown General Purpose Input/Output, weak internal PullUp General Purpose Input/Output, weak internal PullUp / ADC Input JTAG test data output JTAG clock, weak internal Pull-Down General Purpose Input/Output, weak internal PullDown / SPI Clock General Purpose Input/Output, weak internal PullDown / SPI Master Out – Slave In Connect to Ground General Purpose Input/Output, weak internal PullDown / SPI Chip Select General Purpose Input/Output, weak internal PullDown / SPI Master In – Slave Out General Purpose Input/Output, weak internal PullDown / UART2 DATA Output General Purpose Input/Output, weak internal PullDown / UART2 DATA Input USB Data Minus Terminal USB Data Plus Terminal General Purpose Input/Output, weak internal PullDown, do not use as current source! / TAMPER In General Purpose Input/Output, weak internal PullUp / SPI2 Master Out – Slave In General Purpose Input/Output, weak internal PullUp / I2C Serial Clock Line General Purpose Input/Output, weak internal PullUp / I2C Serial Data Line Optional Batterie Backup Type: PU - Pulled up; PD – pulled down; P – Power; I – Input; O – Output; I/O - bidirectional PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 9 of 33 DATE 29.05.2009 Datum 6.2. APPLICATION SPECIFIC PIN DESCRIPTION 6.2.1. SPP configuration DCE Mode No Pin Name SPP-Function Type PU/PD Active Description 1 2 3 4 5 6 7 GND1 ANT UART_RTS# UART_TXD UART_RXD UART_CTS# GPIO[9]/PCM_CLK Power Antenna /RTS TXD RXD /CTS /LED2 P I/O I I O O O PU PD L H H L L 8 9 10 11 12 13 14 15 16 17 GPIO[10]/PCM_O/TXD3 GPIO[7]/PCM_SYNC GND2 ATRST/SPI2_MISO GPIO[8]/PCM_I/RXD3 ATDI/SPI2_CS ATMS BOOT0 VCC RESET# UA2 /LED1 Power reserved /UE1 reserved reserved reserved Power /RESET O O I/O I I/O I I I 18 19 GND3 GPIO[14] Power /RTC-OUT O 20 GPIO[13] /RTC-IN I PU L 21 GPIO[15] I/O PU L 22 GPIO[6]/ADC /DCD or /DCDDTE /RI I/O PU L 23 24 25 26 27 28 29 30 31 ATDO/SPI2_SCK ATCK GPIO[3]/SPI_CLK GPIO[0]/SPI_MOSI GND4 GPIO[2]/SPI_CS GPIO[1]/SPI_MISO GPIO[5]/TXD2 GPIO[4]/RXD2 O O I/O I/O O I O I PU PD PD PD H H - PD H PD H 32 33 34 A B C D USB_DM USB_DP GPIO[17]/TAMPER GPIO[16]/SPI2_MOSI GPIO[12]/I2C_SCL GPIO[11]/I2C_SDA VBAT reserved reserved reserved reserved Power reserved /UE2 reserved DTE-/DCE Select reserved reserved reserved reserved reserved reserved Power I/O I/O I/O I/O I/O I/O - PD PD PD PU PU PU L L L - Connect to Ground Antenna Connector UART Request To Send UART Data Input UART Data Output UART Clear To Send Bluetooth connected. Active if a Bluetooth connection exists. Inactive in idle state. Flashes during startup. User Output 2 Device Ready Connect to Ground leave open User Input 1 leave open leave open for Debug-Use only, nc VCC Reset input (active low for 5 ms); Schmitt triggered Connect to Ground DSR in DCE mode, DTR in DTE mode DTR in DCE mode, DSR in DTE mode Data Carrier Detect , Input in DTE mode Output in DCE mode Ring Indicator, Input in DTE mode Output in DCE mode JTAG JTAG leave open leave open Connect to Ground leave open User Input 2, Break Detect (1) leave open DTE (high) DCE (low) mode selector leave open leave open leave open leave open leave open leave open Optional Batterie Backup PU PU PU PU PD PU L H L H L L Type: PU - Pulled up; PD – pulled down; P – Power; I – Input; O – Output; I/O - bidirectional All other pins do not have a dedicated functionality in SPP mode. See 6.1 General Pin Assignment for all other terminals. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 10 of 33 DATE 29.05.2009 Datum 7. TERMINAL SPECIFICS Interfacebeschreibungen 7.1. RF-INTERFACE - ANT The PAN1455 presents a 50Ω impedance on the antenna pin. If you need antenna support please e-mail to [email protected] or use the PAN1555 with integrated ceramic antenna. 7.2. POWER SUPPLY PAN1455/1555 require a power supply with the following characteristics: Typical : 3.3VDC, min.: 3.0VDC – max.: 3.6VDC, low noise (≤10mV), >80mA peak Due to the technological requirements and the pulsed radio transmission the supply needs to be fed by an ultra fast (response time ≤20µs) linear regulator placed as close as possible to the VSUP pin (16). Functionality has been verified with the following types: TOREX: XC6204x332xx or XC6401xx42xx It is also recommended to place a low ESR capacitor with at least 10µF as close as possible to the VSUP pin (16). NOTE: You must ensure that during operation the supply voltage never drops below 2.8 VDC. Otherwise the flash contents (firmware and/or configuration data) can get lost 7.3. POWER-ON-RESET PAN1455/1555 are equipped with circuitry for generating Power ON/-OFF Reset from the internal core voltage. A reset is generated when the core voltage falls below typically 1.88V and is released when it rises above typically 1.92V. In case of Power-On, Power-Off, Watchdog, Low-Power or Software, RESET# acts as an Output by holding RESET# at ≤ 0.3V for min. 1,5ms and max. 3,5ms. In an application with an external Reset as an Input, for example external Reset-Controller, we recommend to use Open-Drain-Output for this circuit. An external reset shall be generated at RESET# ≤ 0.3V for ≥ 5ms after VSUP has stabilized in the recommended voltage range. The following table shows the pin states of PAN1455/1555 on reset. Pin Name State: PAN1455/1555 UART_RTS# UART_TXD UART_RXD UART_CTS# GPIO[0] – GPIO[13], GPIO[16], GPIO[17] GPIO[14] GPIO[15] Boot0 ATRST ATDI ATMS ATDO ATCK USB_DM USB_DP Input Floating Input Floating Input Floating Input Pull-Up Input Floating Input Pull-Up Input Pull-Up Input Pull-Down Input Pull-Up Input Pull-Up Input Pull-Up Input Floating Input Pull-Down Input Floating Input Floating PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 11 of 33 DATE 29.05.2009 Datum 7.4. UART INTERFACE – TXD, RXD, CTS, RTS The functionality of the interface corresponds to the V.24 / RS-232 standard on TTL-level. Transmission speeds: • 1200 bps • 2400 bps • 4800 bps • 9600 bps • 19200 bps • 38400 bps • 57600 bps • 115200 bps • 230400 bps • 460800 bps • 921200 bps Character representation: • 8 or 9 Bit, even/odd/no Parity, 1or 2 stop bits • 7 Bit, even/odd Parity, 1 or 2 stop bits • 7 Bit no Parity, 2 or 3 stop bits Hardware flow-control with UART_RTS and UART_CTS (active low) TXD PAN1x55 DCE Host RXD DTE RTS CTS Figure 7.1 UART Signal Connections CTS TXD 0 us 16 bytes max RTS RXD 0 uS 2 bytes max Figure 7.2 UART Timing Diagram PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 12 of 33 DATE 29.05.2009 Datum 7.5. 3-WIRE SERIAL INTERFACE When using only GND and UART_Rx, UART_Tx serial lines, you may leave UART_RTS# and UART_CTS# open. Note: Not using flow control can result in loss of data. 7.6. USB INTERFACE 1,2 7.6.1. USB_DP, USB_DN PAN1455/1555 contain a full speed USB version 2.0 compliant interface capable of directly driving an USB cable. The PAN1455/1555 operates as a USB peripheral and responds to requests from a USB master host controller. 7.7. GPIO INTERFACE It is possible to use the programmable digital I/Os GPIO[0:17]. The Current from GPIO[17] is limited to 3mA max. For 5V tolerant GPIO´s refer to chapter 6.2.1SPP configuration DCE Mode 7.8. ADC 3 It is possible to use the programmable I/Os PIO[0:3,6,7,13:15] as ADC. The 12-bit ADC is a successive approximation analogue-to-digital converter. A/D conversion can be performed in single, continuous, scan or discontinuous mode. 7.9. DAC 4 It is possible to use the programmable I/Os PIO[2,3] as ADAC The DAC module is a 12-bit, voltage output digital-to-analogue converter. The DAC can be configured in 8- or 12-bit mode and may be used in conjunction with the DMA controller. 7.10. PCM INTERFACE 5 PCM or Pulse Code Modulation is a sampling technique for digitising analogue signals. The PCM interface for voice applications is provided via the PCM_OUT, PCM_IN, PCM_CLK and PCM_SYNC pins. The PCM interface can act as master or as slave device. In master mode, clock frequencies of 128kHz, 256kHz or 512kHz can be generated, when using the internal 4MHz clock. In slave mode, clock frequencies up to 2048kHz are accepted. The Frame Clock is 8kHz. Long and Short Frame Sync are supported. PAN1455/1555 interface directly to PCM audio devices including the following: 1 subject to firmware support, contact Stollmann for current status. 2 subject to hardware support, contact Stollmann for availability of variants 3 subject to firmware support, contact Stollmann for current status 4 subject to firmware support, contact Stollmann for current status 5 subject to firmware support, contact Stollmann for current status PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 • • • • • PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 13 of 33 DATE 29.05.2009 Datum Qualcom MSM3000 series and MSM5000 series CDMA base band devices OKI MSM7705 four channel A-law and µ-law codec WINBOND W681310 8-bit A-law and µ-law codec WINBOND W681360 13-bit linear codec STW 5093 5094 14-bit linear codec 8. KEY PARTS LIST Liste der Schlüsselkomponenten Part Name Teilenummer Material Material P.W.Board Glass cloth epoxide resin with gold plating BT-IC part name BC63B239A04Q (Cambridge Silicon Radio Ltd www.csr.com) You have to register, before you can download the data sheet. µ-Controller ST32F103xxxx (Cortex baseed STMiroelectronics www.stm.com) PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 14 of 33 DATE 29.05.2009 Datum 9. TEST CONDITIONS Meßbedingungen Measurements shall be made under room temperature and humidity unless otherwise specified. Messungen unter normalen Bedingungen, Abweichungen sind gesondert notiert. Temperature Temperatur 25 ± 10°C 25 ± 10°C Humidity Luftfeuchtigkeit 40 to 85%RH 40 to 85%RH 10. ABSOLUTE MAXIMUM RATINGS (1) Absolute Grenzwerte The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the module will result. No. Item Punkt Supply voltage Versorgungsspannung Voltage on any pin Spannung an jedem Pin Storage temperature range Lagertemperatur Operating temperature range Betriebstemperatur Lead temperature Löttemperatur ESD on any pin ESD Festigkeit 1 2 3 4 6 7 Symbol Zeichen Absolute Maximum Ratings Absolute Grenzwerte Unit Einheit Vcc -0.4 to +3.7 V VPin GND -0.3 to Vcc+0.40 V Tstg -40 to +105 °C Top -40 to +85 °C TDeath See chapter 17.2 °C VESD max 2000 V (CLoad=150pF, RLoad=330Ω) V Notes: (1) ABSOLUTE MAXIMUM RATINGS indicate limits beyond which damage to the device may occur. 11. ELECTRICAL REQUIREMENTS Vcc = 3.3V, Tamb = 25°C if nothing else stated No Item Condition Limit / Grenzen Nr. Punkt Bedingung Min 1 2 3 4 5 Frequency Range Frequenzbereich Load impedance Ausgangsimpedanz Output return loss Ausgangsanpassung Supply voltage Versorgungsspg. Ripple on Vcc AC Anteil auf Vcc Typ 2400 Measured with network analyzer in the frequency range at antenna pin Receive Mode to 50Ω load Transmit Mode to 50Ω load The typical voltage is recommended Vcc at voltage pin Ripple frequency ≥200kHz Ripple frequency <200kHz PANASONIC ELECTRONIC DEVICES EUROPE GMBH Unit Max Einheit 2483.5 MHz Ω 50 -10 -10 3.0 dBm 3.3 3.6 Vdc 10 mVms www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 15 of 33 DATE 29.05.2009 Datum 12. I/O OPERATING CHARACTERISTICS Vcc = 3.3V, Tamb = 25°C if nothing else stated Symbol Item VIL Low-Level Input Voltage VIH High-Level Input Voltage VOL Low-Level Output Voltage VOH IOL IOH IOL (GPIO[17]) IOH (GPIO[17]) High-Level Output Voltage Low -Level Output Current (except GPIO[17]) High-Level Output Current (except GPIO[17]) Low -Level Output Current at GPIO[17] High-Level Output Current at GPIO[17] Iwp-u Input-current Iwp-d Input-current Ilc I/O pad leakage current Ilc I/O pad leakage current Cl Input Capacitance Condition Limit Unit Min Typ Max - 0.5 - 0.8 V - VSUP +0.5 V - - 0.2 V IOH = -4mA VSUP-0.2 - - V VOL = 0.4V - 8 mA 8 mA 3 mA 3 mA VSUP = 3.3V 2.0 IOL = mA VOH = 2.4V VOL = 0.4V VOH = 2.4V Weak pull-up typ. 40kΩ Weak pull-down typ. 40kΩ - - –5.0 –1.0 –0.2 μA +0,2 +1.0 +5.0 μA Standard I/Os –1.0 0 +1.0 μA Vin = 5V -3,0 0 +3,0 μA - 5 - pF 13. USB INTERFACE Vcc = 3.3V, Tamb = 25°C if nothing else stated Item Unit Min Max Input logic level low - 0.3xVSUP V Input logic level high 0.7xVSUP 5.5 V Output logic level low )* 0 0.2 V Output logic level high )* 2.8 VSUP V )* connected to correctly terminated USB cable PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 16 of 33 DATE 29.05.2009 Datum 14. TYPICAL CURRENT CONSUMPTION 14.1. SPP CONFIGURATION 14.1.1. Deep Sleep State The Bluetooth RF is completely deactivated, no paging requests from other Bluetooth devices will be recognized. Only rising control line DTR will activate the PAN1455/1555 and may initiate a Bluetooth link dependent on other parameters. Note: In Deep Sleep state the AT command set is not active, CTS line is low. 14.1.2. Power Down State The Bluetooth RF is activated every 1.25 seconds, paging requests from other Bluetooth devices will be recognized after that intervals and accepted if allowed. Additionally rising control line DTR will activate the PAN1455/1555 and may initiate a Bluetooth link dependent on other parameters. Note: In Power down state the AT command set is not active, CTS line is low. 14.1.3. Idle State No power down mode activated. All functionality is available immediately including connection control using AT command set. 14.2. POWER CONSUMPTION The following values are approximate power consumption values in the different states: VSUP = 3.3V, Tamb = 25°C Condition Current Consumption Unit IMEAN IPEAK Idle, no page scan, no inquiry scan, Uart baud rate: 1200 baud 7,5 15 mA Idle, all functions available, no Bluetooth link, page scan & inquiry scan interval 1,28s 8 56 mA Idle, all functions available, no Bluetooth link, continuous page scans 50 60 mA Bluetooth connected, no data traffic – close range (Slave) 10 56 mA Bluetooth connected, data traffic 115 kbit/s – close range (Slave) 33 61 mA ACL connected DH5 max PWR, shortest Poll Period (Slave) 43 68 mA ACL connected DH5 min PWR, shortest Poll Period (Slave) 42 67 mA ACL connected DH1 max PWR, shortest Poll Period (Slave) 43 69 mA ACL connected DH1 min PWR, shortest Poll Period (Slave) 41 67 mA Power Down 7,5 -- mA Device in reset 1,5 -- mA PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 17 of 33 DATE 29.05.2009 Datum 14.3. POWER-UP TIME The time until the PAN1455/1555 is able to accept link requests or serial data depends on the firmware version and the software parameters RSTTIM and RSTMSG. In the SPP firmware version 1.001 the module is command ready after at least 0,3s (RSTTIM=3 / RSTMSG=0) and 2,16s (RSTTIM=40 / RSTMSG=1) maximum. Bluetooth links are accepted 2,3s after reset. 15. ELECTRICAL RF-CHARACTERISTICS Vcc = 3.0V to 3.6V, Tamb = - 40°C to +85°C Receiver Frequency [GHz] Limit Min Typ 2.402 -70,0 -85,3 2.441 -70,0 -85,4 2.480 -70,0 -86,0 2.402 -70,0 -84,4 2.441 -70,0 -84,9 2.480 -70,0 -85,6 2.402 -70,0 -88,1 2.441 -70,0 -88,3 2.480 -70,0 -88,1 2.402 -70,0 -82,0 2.441 -70,0 -82,7 2.480 -70,0 -82,4 Maximum received signal at 0.1% BER with DH1 -20,0 Maximum received signal at 0.1% BER with DH5 Sensitivity at 0.1% BER DH1 Sensitivity at 0.1% BER DH5 Sensitivity at 0.1% BER EDR2, PI/4 DQPSK Sensitivity at 0.1% BER EDR3, 8DPSK Maximum received signal at 0.1% BER with EDR2, PI/4 DQPSK Maximum received signal at 0.1% BER with EDR3, 8DPSK C/I co-channel a) Unit BT Max Spec ≤-70 dBm ≤-70 dBm ≤-70 dBm ≤-70 dBm >10 ≥-20 dBm -20,0 >10 ≥-20 dBm -20,0 >0 ≥-20 dBm -20,0 >0 ≥-20 dBm 6 11 ≤ 11 dB Adjacent channel selectivity C/I f = f0 + 1MHz a) -5 0 ≤0 dB Adjacent channel selectivity C/I f = f0 - 1MHz a) -5 0 ≤0 dB Adjacent channel selectivity C/I f ≥ f0 + 2MHz a) -38 -30 ≤ -30 dB Adjacent channel selectivity C/I f ≤ f0 - 2MHz a) -22 -20 ≤ -20 dB Adjacent channel selectivity C/I f ≥ f0 + 3MHz a) -42 -40 ≤ -40 dB Adjacent channel selectivity C/I f ≤ f0 - 5MHz a) -45 -40 ≤ -40 dB -15 -9 ≤ -9 dB Adjacent channel selectivity C/I f = fimage a) Notes: a) For BER less then 0,1%. Applies according to BT Test Specification Ver. 1.2/2.0/2.0 + EDR only for Tamb = 20°C PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 18 of 33 DATE 29.05.2009 Datum Vcc = 3.0V to 3.6V, Tamb = - 40°C to +85°C Transmitter RF transmit power 50 Ω load, at antenna b) Class 1 device GFSK Frequency [GHz] Limit Min Typ 2.402 2,3 3,9 3,9 2.441 2,5 3,2 4,0 2.480 2,2 3,0 4,0 2.402 GFSK 2,7 2.402 DPSK 1,6 2.441 GFSK 2,7 2.441 DPSK 1,6 2.480 GFSK 2,2 2.480 DPSK 1,0 2.402 GFSK 2,6 2.402 DPSK RF transmit power 2.441 GFSK 50 Ω load, at antenna Class 1 device EDR3, 8DPSK 2.441 DPSK b) 1,6 2.480 GFSK 2,2 2.480 DPSK 1,0 RF transmit power 50 Ω load, at antenna Class 1 device EDR2, PI/4 b) DQPSK Unit BT Max Spec dBm dBm 2,7 dBm 1,6 RF power control range -21 - 4,0 dB RF power range control resolution 3,2 3,9 4,6 2 to 8 dB 20 dB bandwidth for modulated carrier 920 924 1000 ≤1000 kHz Initial carrier frequency tolerance -75 -10 75 ≤ ±75 kHz Carrier frequency drift (packet DH1) -25 11 25 ≤ ±25 kHz Drift Rate -20 0 20 20 kHz/ 50µs Δf1avg “Maximum Modulation” 140 166 175 ≥140 to ≤175 kHz Δf2avg “Minimum Modulation” 115 155 - ≥ 115 kHz Notes: b) excluding +2dBi antenna gain 16. MECHANICAL REQUIREMENTS Mechanische Anforderungen No. Item Punkt 1 Solderability Lötfähigkeit 2 Resistance to soldering heat Limit Grenzwerte More than 75% of the soldering area shall be coated by solder Mehr als 75% der Lötfläche soll mit Lötpaste bedeckt sein. It shall be satisfied electrical requirements and not be mechanical damage PANASONIC ELECTRONIC DEVICES EUROPE GMBH Condition Bedingung Reflow soldering with recommendable temperature profile See chapter 17.2 www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 19 of 33 DATE 29.05.2009 Datum 17. SOLDERING TEMPERATURE-TIME PROFILE (FOR REFLOW SOLDERING) Temperatur-Zeit Profil für die Reflowlötung 17.1. FOR LEAD SOLDER 10 ±1s Recommended temp. profile for reflow soldering 30 +20/-10s 235°C max. Temp.[°C] 220 ±5°C 200°C 150 ±10°C 90 ±30s Time [s] 17.2. FOR LEADFREE SOLDER Our used temp. profile for reflow soldering Temp.[°C] 30 +20/-10s 230°C -250°C max. 220°C 150°C – 190°C 90 ±30s Time [s] Reflow permissible cycle: 2 Opposite side reflow is prohibited due to module weight. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 20 of 33 DATE 29.05.2009 Datum 18. MODULE DIMENSION Modulabmessungen +0,10 18,75 18,00 +0,00 -0,10 +0,10 -0,10 +0,10 2,70 -0,10 0,80 -0,10 +0,10 -0,10 12,60 13,50 +0,00 -0,10 Figure 18.1 PAN1455 dimensions +0,20 5,90 -0,10 +0,20 0,90 -0,10 +0,10 +0,10 2,80 -0,20 +0,00 -0,10 +0,10 18,00 -0,10 0,80 -0,10 +0,10 2,70 -0,10 22,75 12,60 +0,20 +0,10 -0,10 13,50 +0,00 -0,10 +0,20 5,90 -0,20 0,90 -0,20 +0,20 0,60 -0,20 +0,20 2,60 -0,20 Figure 18.2 PAN1555 dimensions PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 21 of 33 DATE 29.05.2009 Datum 0,65 19. RECOMMENDED FOOT PATTERN Empfohlenes Land Pattern 18,75 1,75 2 3 5 4 6 7 8 9 10 11 Fi nger Rnd 1.0x0.8 33 12 32 13 B 31 15 4,75 30 14 29 A 13,5 1,25 1 1,75 1 34 B 16 Round 0.8 C 28 1,25 27 D 26 17 25 24 6,025 23 22 21 20 19 18 0,65 Figure 19.1 PAN1455 Recommended Land pattern (Top-View not scaled) Dimensions in mm. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF 0, 65 CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 No. REV. DS-1x55-2400-102 0.94 PAGE Seite 22 of 33 DATE 29.05.2009 Datum 22,75 18, 75 1, 75 3 5 4 7 8 9 10 11 Fi nger Rnd 1.0x0. 8 33 12 32 13 B 31 14 15 4, 75 30 ANT 6 29 A 13,5 1, 25 1 2 1, 75 1 34 B 16 Round 0.8 C 28 1,25 27 D 26 17 25 24 23 22 21 6, 025 20 19 18 0, 65 Figure 19.2 PAN1555 Recommended Land pattern (Top-View not scaled) Dimensions in mm. If you have no experience about the land pattern, this figure can guide you, but this information is given without any legal responsibility. We recommend the same dimension for the solder paste screen. The solder screen thickness depends on your production standard, we recommend 120µm to 150µm. IMPORTANT: Please be careful with the area under the module to avoid short cuts. The bottom side from the PAN1455/1555 is fully coated, also the vias! If you have any questions on this point, we are open to discuss your individual situation. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 23 of 33 DATE 29.05.2009 Datum 20. LABELLING DRAWING Kennzeichnung des Modules durch Label 18.0 Top View 1 10 27 18 9.0 000000 081211 Antenna yy zz 9.0 FCC ID: T7V-BC06 IC: 216Q-BC06 13.5 mm 13.5 mm PAN1455 18.75 mm This label is suitable for reflow soldering and designed for the engineering sample status. Information in the 2D-Barcode are the date code in the format • BT-address [12 signs, here 000000000000], (only last six digits are typed on label); • Ordering number [12 signs, please refer also to chapter 24]; • The identifier for the software release (2 signs, here yy); • Datecode: Year-Month-Day [6 signs, here 081211]. All items are separated by a semicolon. ES stands for Engineering Samples, please refer to chapter General Information. In mass production status, the ES will be eliminated. As a summary: zz yy 000000 081211 Identifier for the hardware version Identifier for the software version BT-Address last six digits Datecode 21. SOFTWARE Software We are able to deliver our modules with different software, for different customer application. Before you start your mass production, please check to your best knowledge, that the used software meets your requirements. 21.1. SPP SOFTWARE This SPP software is from our software partner company Stollmann www.stollmann.de. Please refer to Reference [1] . 21.2. HDP SOFTWARE The Health Device Profile is under development and will be released soon. 21.3. HID SOFTWARE The Human Inteface Device Software is under development and will be released soon. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 24 of 33 DATE 29.05.2009 Datum 22. CAUTIONS Warnungen Failure to do so may result in degrading of the product’s functions and damage to the product. 22.1. DESIGN NOTES Designhinweise (1) Please follow the condition written in this specification, especially the control signals of this module. (2) The supply voltage has to be free of ac ripple voltage, as for example from a battery or a low noise regulator output. For noisy supply voltages provide a decoupling circuit as for example a ferrite in series connection and a blocking capacitor to ground of at least 47uF directly at the module. (3) This product should not be stressed when installed. (4) Heat is the major cause of shortening the life of these products. Please keep this product away from heat. Avoid assembly and use of the target equipment in conditions where the products' temperature may exceed the maximum allowable. (5) The supply voltage should not be exceeding or reverse, and should not carry noise and spike. (6) Please keep this product away from other high frequency circuits. 22.2. INSTALLATION NOTES Verarbeitungshinweise (1) (2) (3) (4) (5) (6) (7) (8) (9) Reflow soldering is possible for twice on the condition in chapter 15. Please set up the temperature at the soldering portion of this product according to this reflow profile. Carefully position the products so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. Carefully locate these products so that their temperatures will not increase due to the effects of heat generated by neighboring components. If a vinyl-covered wire comes into contact with the products, then the cover will melt and generate toxic gas, damaging the insulation. Never allow contact between the cover and these products to occur. This product should not be stressed or vibrated when reflowed. Please keep the following conditions when you install this product for reparation by hand soldering. Please do not wash this product. Please refer to the recommended pattern when designing a board. Pressing on parts of the metal cover or fastening objects to the metal cover is not allowed. 22.3. USAGE CONDITIONS NOTES Benutzerhinweise (1) (2) Please take measure against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, then before use, check and evaluate their operation when assembled on your products. Please do not use the fallen product. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 (3) (4) (5) (6) (7) PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 25 of 33 DATE 29.05.2009 Datum Please do not put on damage and dirt to the pin , and don't touch the electric components. Please follow the condition written in the ratings , about the power supply instruments applied to this product. Electrode peeling strength: Do not add pressure of more than 4.9N when soldered on PCB Pressing on parts of the metal cover or fastening objects to the metal cover is not allowed. These products are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information and communication equipment. 22.4. STORAGE NOTES Lagerhinweise (1) (2) (3) (4) (5) (6) The module may not be stressed mechanically during storage. Do not store these products in the following conditions or the performance characteristics of the product, such as RF performance will be adversely affected: • Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX • Storage in direct sunlight • Storage in an environment where the temperature may be outside the range of 5°C to 35°C range, or where the humidity may be outside the 45 to 85% range. • Storage of the products for more than one year after the date of delivery at your company if the avoidance all the above conditions (1) to (3) have been met. Storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. Please keep this product away from water, poisonous gas and corrosive gas. This product should not be stressed or shocked when transported. Please follow the specification when piling up the packed crate ( max. 10). 22.5. SAFETY CAUTIONS Sicherheitshinweise These specifications are intended to preserve the quality assurance of products as individual components. Before use, check and evaluate their operation when mounted on your products. Abide by these specifications, without deviation when using the products.These products may shortcircuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, then at least, provide the following failsafe functions, as a minimum. (1) Ensure the safety of the whole system by installing a protection circuit and a protection device. (2) Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 26 of 33 DATE 29.05.2009 Datum 22.6. OTHER CAUTIONS Weitere Hinweise (1) (2) (3) (4) (5) (6) (7) This specification sheet is copyrighted. Please do not open it to the third party. Please do not use this product of our company for another purpose. Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. This product has not been manufactured with any ozone chemical controlled under the Montreal Protocol. These products are not intended for other uses, other than under the special conditions shown below. Before using these products under such special conditions, check their performance and reliability under the said special conditions carefully to determine whether or not they can be used in such a manner. • In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash. • In direct sunlight, outdoors, or in a dusty environment • In an environment where condensation occurs. • In an environment with a high concentration of harmful gas (e.g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOX) If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these products with new products because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. When you have any question or uncertainty , both of you and Panasonic sincerely cope with it. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 27 of 33 DATE 29.05.2009 Datum 23. PACKAGING Verpackung 23.1. EMBOSSED TAPE / BLISTERGURT (1) Dimension of the tape / Abmessungen des Gurtes (EIAJ-tbd) (2) Cover tape reel strength / Abzugskräfte Blistergurt Deckfolie Force direction θ= 10deg Speed = 300mm/min. Cover tape reel strength =0.098～0.68N (10～70g) PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 (3) PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE No. REV. DS-1x55-2400-102 0.94 PAGE Seite 28 of 33 DATE 29.05.2009 Datum ENW89815C3KF/ENW89815A3KF Empty hollow / leere Taschen Direction of feed Vorschubrichtung Empty hollow more than 10 pitch Mehr als 10 leere Taschen Component Empty hollow more packed area than 10pitch Modulbereich Mehr als 10 leere Taschen Top cover tape more than 200mm Deckfolie groesser 200mm als Empty hollow in component packed area shall be less than two per reel and those hollows shall not be consecutive. Es dürfen minimal 2 leere Taschen im Bereich der Komponenten vorhanden sein, diese dürfen aber nicht aufeinander folgen. 23.2. COMPONENT DIRECTION Komponentenanordnung Top cover tape shall not be found on reel holes and shall not stick out from reel. Deckfolien darf nicht durch die Löcher der Spule und nicht außerhalb der Spule geführt werden. Tape running direction Laufrichtung des Bandes (top view) 18 Part No. 27 1 10 Component direction Komponentenrichtung (See also chapter 21) Figure 1 23.3. REEL DIMENSION Abmaße der Rolle (1) (2) Quantity per reel : 500 pieces Anzahl pro Rolle : 500 Stück Marking : Customer’s part No. / Quantity / Lot No. and Our part# with bar-code shall be on the reel. Kennzeichnung : Kundennummer / Anzahl / Losnummer und unsere Komponentennummer als Barcode wird auf die Rolle gedruckt Refer to figure 2 Bezugnehmend zur Zeichnung 2 PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 29 of 33 DATE 29.05.2009 Datum 23.4. PACKAGE Umverpackung (1) (2) Package box : Paketbox.: Marking : φ 13 +/-1 2 +/-0.5 φ 80 +/-2 φ 13 +/-0.5 Kennzeichnung : 1 or 2 reel (depends on quantity) 1 oder 2 Rollen (abhängig von der Liefermenge) Customer’s part No. / Quantity / Lot No. and Our part# with bar-code shall be on the package box. Kundennummer / Anzahl / Losnummer und unsere Komponentennummer als Barcode wird auf die Verpackung gedruckt Refer to figure 2 and 3 Bezugnehmend zur Zeichnung 2 und 3 Marking Figure 3 Marking ? φ 330 Figure 2 33.5 +/-1.0 2.0 +/-0.2 PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 30 of 33 DATE 29.05.2009 Datum 24. ORDERING INFORMATION Bestellinformationen Ordering part number ENW89815C3KF ENW89815A3KF Description PAN1455 256kByte Flash Memory, without Antenna (2) Software: SPP PAN1555 256kByte Flash Memory, with Antenna (2) Software: SPP MOQ (1) 500 500 Notes: (1) Abbreviation for Minimum Order Quantity (MOQ). The standard MOQ for mass production are 500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity. (2) This software is licensed by the company Stollmann please refer to [1] . 25. ROHS DECLARATION RoHS-Erklärung Declaration of environmental compatibility for supplied products: Hereby we declare to our best present knowledge based on declaration of our suppliers that this product do not contain by now the following substances which are banned by Directive 2002/95/EC (RoHS) or if contain a maximum concentration of 0,1% by weight in homogeneous materials for • • • • • Lead and lead compounds Mercury and mercury compounds Chromium (VI) PBB (polybrominated biphenyl) category PBDE (polybrominated biphenyl ether) category And a maximum concentration of 0,01% by weight in homogeneous materials for • Cadmium and cadmium compounds 26. DATA SHEET STATUS Datenblatt Status This data sheet contains preliminary product specification. Panasonic reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. Please consult the most recently issued data sheet before initiating or completing a design. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 31 of 33 DATE 29.05.2009 Datum 27. REGULATORY INFORMATION 27.1. FCC NOTICE The device PAN1555, including the ceramic antenna (ENW89815C3KF) and also the SMD type PAN1455 (ENW89815A3KF), including with the antennas, which are listed in 27.5, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407.transmitter Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 27.2. CAUTION The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Electronic Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help 27.3. LABELING REQUIREMENTS The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier are FCC ID: T7V-BC06. This FCC identifier is valid for both versions, for details, please see the chapter 24. Ordering Information. In any case end product must be labelled exterior with "Contains FCC ID: T7V-BC06" PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 32 of 33 DATE 29.05.2009 Datum 27.4. ANTENNA WARNING The related part number for this device is ENW89815A3KF (PAN1455 with SMD pad). For details, please see the chapter 24. Ordering Information. This device are tested with a standard SMA connector and with the antennas listed below. When integrated in the OEMs product, these fixed antennas require installation preventing end-users from replacing them with non-approved antennas. Any antenna exceeding 2dBi not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions. The FCC identifier for this device with the antenna listed in item 1 are the same (FCC ID: T7V-BC06). 27.5. APPROVED ANTENNA LIST Note: We are able to qualify your antenna and will add to this list as that process is completed. Item Part Number Manufacturer Frequency Band Type Gain (dBi) 1 WIMO17010.10 Wimo 2.4GHz ROD +2 2 27.6. RF EXPOSURE PAN1455/PAN1555 To comply with FCC RF Exposure requirements, the Original Equipment Manufacturer (OEM) must ensure that the approved antenna in the previous table must be installed. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of PAN1455 with mounted ceramic antenna (FCC ID: T7V-BC06) is far below the FCC radio frequency exposure limits. Nevertheless, the PAN1455 shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. 27.7. INDUSTRY CANADA CERTIFICATION PAN1455/PAN1555 comply with the regulatory requirements of Industry canada (IC), license: IC: 216Q-BC06 Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca This device has been designed to operate with the antenna listed in section 27.5 above, having a maximum gain of 2.0 dBi. Antennas not included in this list or having a gain greater than 2.0 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The antenna used for this transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de CLASSIFICATION Einstufung SUBJECT Thema CUSTOMER’S CODE PAN1455/1555 PRODUCT SPECIFICATION Produktspezifikation CLASS 2 BLUETOOTH MODULE Bluetooth Modul der Klasse 2 PANASONIC’S CODE ENW89815C3KF/ENW89815A3KF No. REV. DS-1x55-2400-102 0.94 PAGE Seite 33 of 33 DATE 29.05.2009 Datum 28. RELATED DOCUMENTS Mitgeltende Dokumente [1] BlueRS+_ATCommand_Reference 29. GENERAL INFORMATION Allgemeine Informationen © Panasonic Electronic Devices Europe GmbH 2009. All rights reserved. This product description does not lodge the claim to be complete and free of mistakes. Please contact the related product manager in every case. If we deliver ES samples to the customer, these samples have the status Engineering Samples. This means, the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and there may be differences to be published Data Sheet. Engineering Samples are not qualified and are not to be used for reliability testing or series production. Disclaimer: Customer acknowledges that samples may deviate from the Data Sheet and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by • the use of the Engineering Sample other than for Evaluation Purposes, particularly the installation or integration in an other product to be sold by Customer, • deviation or lapse in function of Engineering Sample, • improper use of Engineering Samples. Panasonic disclaimes any liability for consequential and incidental damages. In case of any questions, please contact your local sales partner or the related product manager. 30. LIFE SUPPORT POLICY Politik für Lebenserhaltungssysteme This Panasonic product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic for any damages resulting. PANASONIC ELECTRONIC DEVICES EUROPE GMBH www.pedeu.pansonic.de