ISL7119RH ® Data Sheet October 8, 2008 Radiation Hardened High Speed Dual Voltage Comparator FN6607.2 Features • Electrically Screened to DSCC SMD # 5962-07215 The ISL7119RH is a radiation hardened high speed dual voltage comparator fabricated on a single monolithic chip. It is designed to operate over a wide dual supply voltage range as well as a single 5V logic supply and ground. The open collector output stage facilitates interfacing with a variety of logic devices and has the ability to drive relays and lamps at output currents up to 25mA. The ISL7119RH is fabricated on our dielectrically isolated Rad-hard Silicon Gate (RSG) process, which provides immunity to Single Event Latch-up (SEL) and highly reliable performance in the natural space environment. • QML Qualified Per MIL-PRF-38535 Requirements • Radiation Environment - Total Dose. . . . . . . . . . . . . . . . . . . . . . . 3 x 105 RAD(Si) - SEL/SEB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Immune • Input Offset Voltage (VIO). . . . . . . . . . . . . . . . . 8mV (Max) • Input Bias Current (IBIAS) . . . . . . . . . . . . . .1000nA (Max) • Input Offset Current (IIO) . . . . . . . . . . . . . . . .150nA (Max) • Saturation Voltage @ ISINK = 3.2mA (VSAT) . 0.65V (Max) • Saturation Voltage @ ISINK = 25mA (VSAT) . . 1.8V (Max) Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed below must be used when ordering. • Response Time (tPD) . . . . . . . . . . . . . . . . . . . 160ns (Max) Detailed Electrical Specifications for the ISL7119RH are contained in SMD 5962-07215. A “hot-link” is provided on our website for downloading. • Window Detector Applications • Level Shifter • Relay Driver Pinouts • Lamp Driver ISL7119RH (10 LD FLATPACK GDFP1-F10 OR CDFP2-F10) TOP VIEW s OUT 1 1 10 +VS GND 1 2 9 -IN 2 +IN 1 3 8 +IN 2 -IN 1 4 7 GND 2 -VS 5 6 OUT 2 Ordering Information ORDERING NUMBER INTERNAL MKT. NUMBER PART MARKING TEMP. RANGE (°C) PACKAGE PKG. DWG. # 5962F0721501QXC ISL7119RHQF Q 5962F07 21501QXC -55 to +125 10 Ld Flatpack K10.A 5962F0721501VXC ISL7119RHVF Q 5962F07 21501VXC -55 to +125 10 Ld Flatpack K10.A 5962F0721501V9A ISL7119RHVX -55 to +125 10 Ld Flatpack K10.A ISL7119RH/Proto ISL7119RHF/Proto -55 to +125 10 Ld Flatpack K10.A 1 ISL7 119RHF /Proto CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2007, 2008. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL7119RH Die Characteristics DIE DIMENSIONS: Backside Finish: 2030µm x 2030µm (~80 mils x 80 mils) Thickness: 483µm ± 25.4µm (19 mils ± 1 mil) INTERFACE MATERIALS: Silicon ASSEMBLY RELATED INFORMATION: Substrate Potential: Glassivation: Unbiased (DI) Type: PSG (Phosphorous Silicon Glass) Thickness: 8.0kÅ ± 1.0kÅ ADDITIONAL INFORMATION: Worst Case Current Density: Top Metallization: <2.0 x 105 A/cm2 Type: AlSiCu Thickness: 16.0kÅ ± 2kÅ Transistor Count: 66 Substrate: Radiation Hardened Silicon Gate, Dielectric Isolation Metallization Mask Layout ISL7119RH All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 2 FN6607.2 October 8, 2008