Download

30W DC-DC Converter P30F-Series
●
●
●
●
●
●
●
●
●
●
Wide 4:1 input range
Efficiency up to 90%
Adjustable output voltage
Remote control on/off
1500 VDC isolation
Continuous short circuit protection
Over voltage protection
Standard package 2” x 1.6 x 0.4”
MTBF > 1 Mio. hours
-40...+85°C operating temperature range
Model guide
Type
Input
nominal
voltage
Input current
no load
full load
[VDC]
Single output
P30F2405S
9...36
P30F2412S
9...36
P30F2415S
9...36
P30F4805S
18...75
P30F4812S
18...75
P30F4815S
18...75
Dual output
P30F2405D
9...36
P30F2412D
9...36
P30F2415D
9...36
P30F4805D
18...75
P30F4812D
18...75
P30F4815D
18...75
With suffix “K” heatsink version
Output
voltage
Output current
minimum
maximum
load
load
Efficiency
@ full load
typ.
Capacitive
load
(see note 3)
[mA]
[mA]
[VDC]
[mA]
[A]
[%]
[µF] max.
120
30
30
100
30
30
1420
1420
1420
710
710
702
5
12
15
5
12
15
300
125
100
300
125
100
6000
2500
2000
6000
2500
2000
88
88
90
88
88
89
6000
2500
1100
6000
2500
1100
30
30
30
30
30
30
1450
1420
1420
715
718
718
±5
±12
±15
±5
±12
±15
±150
±63
±50
±150
±63
±50
±3000
±1250
±1000
±3000
±1250
±1000
86
89
90
86
87
87
2 x 2000
2 x 1250
2 x 680
2 x 2000
2 x 1250
2 x 680
1) Recommended circuit
The P30F series is been tested according to the following recommended test circuit before leaving the factory (see Figures 1).
If you want to further decrease the input / output ripple, you can increase a capacitance values properly or choose capacitors with
low ESR, but the total capacitance of the filter capacitor must not exceed the maximum load capacitance value (see Model guide
table).
Figure 1a
+ Input
Figure 1b
+ Vin
DC
Cin
- Input
- Vin
+ Input
+ Vout
Cout
DC
- Vout
Recommended peripheral components to figure 1a
Cin
Cout
P30Fxx05S
10 µF
10 µF
P30Fxx12S
10 µF
4.7 µF
P30Fxx15S
10 µF
4.7 µF
+ Vin
Cout
DC
Cin
- Input
+ Vout
- Vin
DC
Cout
- Vout
Recommended peripheral components to figure 1b
Cin
Cout
P30Fxx05D
10 µF
10 µF
P30Fxx12D
10 µF
4.7 µF
P30Fxx15D
10 µF
4.7 µF
Page 1 of 7
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
30W DC-DC Converter P30F-Series
Specifications
General
Start up time
Switching frequency
Safety standard in accordance with
Reliability Calculated MTBF
MIL-HDBK-217F @ 25 °C
EMC characteristics
Radiated emissions
Radiated emissions, with Fig. 2
Conducted emissions
Conducted emissions, with Fig. 2
ESD, with Fig. 2
RS
EFT, with Fig. 2
Surge, with Fig. 2
CS
Environmental
Operating temperatur
(ambient)
Case temperature
Storage temperature
Over temp. protection
Humidity
Cooling
Physical
Dimensions without heatsink
with heatsink
Weight
without heatsink
with heatsink
Case material
Potting Material
Absolute max. ratings
Pin soldering temperature
1.5 mm distance from body
Max. input voltage for 1 s
Vin 24 V types
Vin 48 V types
Input
Under Voltage lockout
on @ 9 VDC, off @ 7.8 VDC
Vin 24V types
Vin 48V types
on @ 17.8 VDC, off @ 16 VDC
Filter
π - type
Reflected ripple current *6
30 mAp-p, typ.
Remote control theshold
On state 2.5…12 VDC, or open input
Off state 0…1.2 VDC
Input idle current
Off state 1 mA, typ.
Isolation input - output:
Rated voltage (tested for 1 min.)
1500 VDC
9
Resistance
> 10 Ω, measured @ 500 VDC
Capacitance
2000 pF, typ.
Output
Voltage tolerance
± 3 %, max.
Voltage load regulation
± 1 % @ 5 %...100 % load
Output voltage trim range
± 10 %
±5 %, max. @ 10 % / 100 %
Voltage cross balance
(dual outputs)
load difference
Voltage regulation
± 0.5 %, max @ full Vin range
Temperature coefficient
± 0.02 % / °C
Transient recovery time
<500 µs, @ 25 % load steps
Transient response deviation <5 %, @ 25 % load steps
Short circuit protection
Continuous, hiccup
Short circuit restart
Automatic
Over load protection
150 % of full load, typ.
Rippel & noise, BW 20MHz
100 mVp-p, max.
Over voltage protection via integrated TVS Diode
P30Fxx05x
6.1 VDC
P30Fxx12x
15 VDC
P30Fxx55x
18 VDC
10 ms, typ @ R-load
400 kHz, typ.
IEC / EN 60950-2001
> 1 Mio. hours
CISPR22 / EN55022 Class A
CISPR22 / EN55022 Class B
CISPR22 / EN55022 Class A
CISPR22 / EN55022 Class B
EN61000-4-2 perf. crit. B
EN61000-4-3 perf. crit. A
EN61000-4-4 perf. crit. B
EN61000-4-5 perf. crit. B
EN61000-4-6 perf. crit. A
-40 °C to +85 °C with derating
-40 °C to +60 °C full load
105 °C, max.
-55 °C to +125 °C
t-case 110 °C, typ
5…95 %, non-condensing
Free air convection
50.80 x 40.60 x 11.8 mm
50.80 x 40.60 x 16.3 mm
50 g
70 g
Aluminium Alloy
Epoxy (UL94V-0 rated)
300°C for 10 sec
-0.7…50 VDC
-0.7…100 VDC
Note:
1. Min. load should not be less than 5 %, otherwise ripple maybe increased dramatically, If the product operates under min. load,
it may not be guaranteed to meet all specifications listed. Operation under minimum load will not damage the converter.
2. The recommended unbalanced load of dual output converter should be low than 5%. If the load asymmetry greater than 5%, it
may not be guaranteed to meet all specifications listed. Please contact our technical support for more details.
3. Maximum capacitive load is tested at input voltage range and full load.
4. All specifications measured at Ta=25°C, humidity <75 %, nominal input voltage and rated output load unless otherwise
specified.
5. In this datasheet, all test methods are based on our corporate standards.
6. All characteristics are for listed models, and non standard models may perform differently. Please contact our technical support
for more details.
7. Please contact our technical support for any specific requirement.
8. Specifications of this product are subject to changes without prior notice.
9. It is not recommended to increase the output power capability by connecting two or more converters in parallel. The converters
are not hot swappable
Input reflected ripple measure circuit
Measure point
+ Input
+ Vin
Lin
4.7 µH
+ Vout
DC
Load
- Input
Cin 220 µF
ESR < 1 Ω
at 100 kHz
DC
- Vin
- Vout
The input reflected ripple current is measured with inductor Lin and capacitor Cin to simulate source impedance.
Page 2 of 7
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
30W DC-DC Converter P30F-Series
Figures 2, Recommended EMC circuit
Single output
L1
Fuse
LCM
+Vin
CY
+Vout
+ Input
DC
D1
ΔU
C1
CX
CX
Load
MOV
DC
-Vout
-Vin
- Input
Recommended EMS circuit
Recommended EMi circuit
CY
Dual output
L1
Fuse
LCM
+Vin
CY
+Vout
+ Input
DC
D1
ΔU
C1
CX
Load
CX
Com.
MOV
Load
DC
-Vout
-Vin
- Input
Recommended EMS circuit
Recommended EMi circuit
CY
Recommended peripheral components to circuits in figures 2
Fuse
MOV
L1
D1
C1
Slow bolw
Type
Type
P30F24xxS
2.5 A
10D560K 56 µH SMCJ48A
120 µF, 50 V
P30F24xxD
2.5 A
10D560K 56 µH SMCJ48A
120 µF, 50 V
P30F48xxS
1.5 A
10D101K 56 µH SMCJ90A 120 µF; 100 V
P30F48xxD
1.5 A
10D101K 56 µH SMCJ90A 120 µF, 100 V
CX
LCM
CY
4.7µF
4.7µF
2.2µF
2.2µF
2.2 mH
2.2 mH
2.2 mH
2.2 mH
1nF, 2 kV
1nF, 2 kV
1nF, 2 kV
1nF, 2 kV
Recommended layout with EMC periphery
Single output
Dual output
Page 3 of 7
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
30W DC-DC Converter P30F-Series
Application note to remote control / trim function
+ Input
+ Vin
Remote
control
input
+ Vout
DC
R trim down
Open switch
for “ON”-state
R trim up
DC
- Input
- Vin
- Vout
Trim up circuit
Trim down circuit
+Vout
+Vout
P30FxxxxS
P30FxxxxD
R1
R1
Rtd
R3
+
R2
Common
Common
R3
-
-
+
R2
Rtu
VRef
VRef
-Vout
-Vout
Calculation for trim down resistor (Rtd) or trim up resistor (Rtu)
Model series
R1 [kΩ]
R2 [kΩ]
R3 [kΩ]
V Ref [V]
P30Fxx05S
2.883
10
2.5
2.864
P30Fxx12S
10.971
2.5
17.8
P30Fxx15S
14.497
2.5
Maximum output voltage adjust range ± 10 % of Vout nominal, see min. Rtd / Rtu
Trim down resistor formula
b=
Vout-Vref
Rtd=
Vref
R1*b
R1-b
Rtd min. [kΩ]
1.16
53.5
78.6
Rtu min. [kΩ]
4.9
6.6
9.1
Trim up resistor formula
*R2
a=
-R3
Vref
Vout-Vref
Rtu=
R2*a
R2-a
*R1
-R3
Page 4 of 7
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
30W DC-DC Converter P30F-Series
P30Fxxxxx
P30FxxxxxK
Page 5 of 7
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
30W DC-DC Converter P30F-Series
Page 6 of 7
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
30W DC-DC Converter P30F-Series
Dimensions
Pin configuration
Pin
1
2
3
4
5
6
7
Single
+ Vin
- Vin
Rem ctrl
Trim
- Vout
+ Vout
No pin
Dual
+ Vin
- Vin
Rem ctrl
Trim
- Vout
Common
+ Vout
Unit: mm
Pin diameter tolerance: 0.1 mm
Pin height tolerance: 0.5 mm
General tolerances: 0.30 mm
Unit
PHI-CON is a trademark of HY-LINE power components.
Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions
carefully before using!
Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without
the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and
whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably
expected to result in significant injury to the user. Rev: 03.14 f
Page 7 of 7
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
Similar pages