CD2419-B08200 - B08800 Bridge Rectifier Diode Series

The 800 Series is obsolete,
and not recommended for new
designs.
PL
IA
NT
Features
CO
M
■ Optimizes data transmission in ECL
*R
oH
S
systems through proper termination
between drivers and receivers
■ Minimizes overshoot, undershoot, and
ringing while increasing noise immunity
■ Provides decoupling capacitors
■ RoHS compliant*
For information on ECL Terminators, download
Bourns’ ECL Terminator Application Note.
800 Series - RC Networks ECL Terminator Circuits
General Description
Digital systems incorporating Emitter
Coupled Logic (ECL) or other ultra-high
switching speed logic families will
require signal termination to prevent
transmission line effects such as reflections and ringing due to fast transition
times.
Bourns 800 series resistor capacitor
networks are ideal for termination of
high speed transmission lines. Each
network is composed of resistors
for parallel termination and bypass
capacitor(s) for cross talk noise
reduction.
Product Dimensions
Typical Part Marking
MEDIUM PROFILE
801 AND 802
A
MAXIMUM
6.35
(.250)
MAX.
Represents total content. Layout may vary.
CIRCUIT
PART NUMBER
PIN #1
REF.
MAX. 1.24
BOTH ENDS (.049)
.508 ± .050
TYP.
(.020 ± .002)
2.54 ± .07
(.100 ± .003*)
TYP.
NON-ACCUM.
PIN ONE
INDICATOR
3.43 + .38/ - .25
(.135 + .015/ - .010)
803 AND 805
E
T
E
L
O
S
B
O
Physical Characteristics
Flammability ........Conforms to UL94V-0
Leadframe ..................Copper (Olin 194)
Body Material ............. Epoxy/Anhydride
(Conformal Material)
Custom Resistance Range
........................ 10 ohms to 50K ohms
Custom Capacitance Range
........................... 39 pF to 100,000 pF
NPO and Z5U dielectrics available on a
custom basis.
RESISTANCE
CODE
DATE CODE
MANUFACTURER'S
TRADEMARK
Represents total content. Layout may vary.
3.81
MAX.
(.150)
The 5 conformal coated SIP circuit
variations offered are as follows.
Electrical Characteristics
Resistance Tolerance .................... ±5 %
Resistance Power...................... 0.1 watt
Capacitance Tolerance ................ ±20 %
Capacitor Dielectric Type ................ X7R
Capacitance Voltage Rating ...... 50 Volts
4608M-801
500/103
YYWW
PART NUMBER
CIRCUIT
4610H-805
500/103
YYWW
PIN ONE
INDICATOR
.254 ± .050
TYP.
(.010 ± .002)
RESISTANCE
CODE
DATE CODE
MANUFACTURER'S
TRADEMARK
HIGH PROFILE
A
MAXIMUM
8.89
(.350)
MAX.
Represents total content. Layout may vary.
PART NUMBER
PIN #1
REF.
MAX. 1.24
BOTH ENDS (.049)
.508 ± .050
TYP.
(.020 ± .002)
2.54 ± .07
(.100 ± .003*)
TYP.
NON-ACCUM.
804
3.43 + .38/ - .25
(.135 + .015/ - .010)
PIN ONE
INDICATOR
CIRCUIT
4612M-804
500
YYWW
RESISTANCE
CODE
DATE CODE
MANUFACTURER'S
TRADEMARK
2.49
MAX.
(.098)
For Standard Values Used in
Capacitors, Inductors, and Resistors,
click here.
.254 ± .050
TYP.
(.010 ± .002)
Governing dimensions are metric. Dimensions in parentheses
are inches and are approximate.
*Terminal centerline to centerline measurements made at point of
emergence of the lead from the body.
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Features
■ Minimizes space and routing problems,
and reduces manufacturing cost per
installed resistive function
■ Increases board yields and reliability by
reducing component count
800 Series - RC Networks ECL Terminator Circuits
801 8, 10 and 12 Pin SIP
(4608M-801-RC/CCL)
Designed to terminate 6 to 10 transmission lines using parallel termination
techniques. Standard resistance values
include 50, 68, 75, 82, 90 or 100 ohms
and are chosen to match the characteristic impedance (Zo) of the transmission
line. A 0.01 μF capacitor is provided to
help maintain a solid power supply level
within the network package, mitigating
any cross talk or feedthrough effects.
Values for R and C not shown in the
following table are available on a
custom basis.
802 10 Pin SIP
(4610M-802-RC/CCL)
Designed to terminate 6 transmission
lines using parallel termination techniques. Popular resistance values
include 50, 68, 75, 82, 90 or 100 ohms
and are chosen to match the characteristic impedance (Zo) of the transmission
line. Two 0.01 μF capacitors are
provided to reduce cross talk between
lines and to decrease network package
inductance. Values for R and C not
shown in the following table are available
on a custom basis.
Standard 801 Part Numbers
Standard 802 Part Numbers
Bourns Part Number
Bourns Part Number
4608M-801-500/103L
4608M-801-680/103L
4608M-801-750/103L
4608M-801-820/103L
4608M-801-900/103L
4608M-801-101/103L
50 Ω
68 Ω
75 Ω
82 Ω
90 Ω
100 Ω
0.01 μF
0.01 μF
0.01 μF
0.01 μF
0.01 μF
0.01 μF
4610M-802-500/103L
4610M-802-680/103L
4610M-802-750/103L
4610M-802-820/103L
4610M-802-900/103L
4610M-802-101/103L
802 Electrical Schematic and Application
Zo
±2 %
R1
R2
C
±20 %
Bourns Part No.
50 Ω
70 Ω
75 Ω
80 Ω
90 Ω
100 Ω
120 Ω
150 Ω
200 Ω
81 Ω
113 Ω
121 Ω
130 Ω
146 Ω
162 Ω
194 Ω
243 Ω
325 Ω
130 Ω
182 Ω
195 Ω
208 Ω
234 Ω
260 Ω
312 Ω
390 Ω
520 Ω
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
4610H-803-500/104L
4610H-803-700/104L
4610H-803-750/104L
4610H-803-800/104L
4610H-803-900/104L
4610H-803-101/104L
4610H-803-121/104L
4610H-803-151/104L
4610H-803-201/104L
Vcc
Line 5
803 Electrical Schematic and Application
R2
C
R1
Vcc
Line 8
Line 7
Line 6
Line 5
Line 4
Line 3
Line 2
10
Line 1
1
Vee
Vtt
10
Line 4
1
Line 1
Vtt
Line 6
Line 5
Line 4
Line 3
Line 2
8
Line 1
Vcc
1
Standard 803 Part Numbers
Line 6
801 Electrical Schematic and Application
Line 3
0.01 μF
0.01 μF
0.01 μF
0.01 μF
0.01 μF
0.01 μF
C
±20 %
Vtt
50 Ω
68 Ω
75 Ω
82 Ω
90 Ω
100 Ω
E
T
E
L
O
S
B
O
R
±2 %
Line 2
C
±20 %
Vcc
R
±2 %
803 8, 10 and 12 Pin SIP 10K ECL
(4610H-803-ZoC/CCL)
Designed to terminate 6 to 10
transmission lines using Thevenin equivalent parallel termination techniques in
systems using 10K ECL. Popular
impedance values include 50, 70, 75,
80, 90, 100, 120, 150 or 200 ohms.
Standard values for R1 and R2, based
on Zo, have been chosen to accommodate 10K ECL designs. A 0.1 μF
capacitor is provided to reduce cross
talk noise within the network package.
Values for Zo and C not shown in the
following table are available on a custom basis. This type of termination is an
alternative to parallel termination used
when a separate Vtt power supply is not
available.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
800 Series - RC Networks ECL Terminator Circuits
804 12 Pin SIP ECL
(4612M-804-RCL)
Designed to terminate 6 transmission
lines using parallel termination techniques. Popular resistance values
include 50 or 100 ohms. A 0.1 μF
capacitor is provided for connection
to Vee. Two 0.01 μF capacitors are
provided for connection to Vtt. Values
for R and C not shown in the following
table are available on a custom basis.
How To Order 801
46 08 M - 801 - 500 103 L
Model
(46 = Conformal SIP)
Number of Pins
(8, 10, 12)
Physical Config.
• M = Medium Profile
Electrical Configuration
Resistance Code
• First 2 digits are significant
• Third digit represents the number of
zeros to follow.
• Units = ohms
Capacitance Code
• First 2 digits are significant
• Third digit represents the number of zeros to
follow.
• Units = picofarads
Termination
L = Lead Free (Sn/Ag/Cu-plated)
Consult factory for other available options.
E
T
E
L
O
S
B
O
Standard 805 Part Numbers
Zo
±2 %
R1
50 Ω
70 Ω
75 Ω
80 Ω
90 Ω
100 Ω
120 Ω
150 Ω
200 Ω
90 Ω
126 Ω
135 Ω
144 Ω
161 Ω
180 Ω
216 Ω
270 Ω
360 Ω
How To Order 803 and 805
46 08 H - 803 - 101 103 L
R2
C
±20 %
Bourns Part No.
113 Ω
158 Ω
169 Ω
180 Ω
202 Ω
225 Ω
270 Ω
338 Ω
450 Ω
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
0.1 μF
4610H-805-500/104L
4610H-805-700/104L
4610H-805-750/104L
4610H-805-800/104L
4610H-805-900/104L
4610H-805-101/104L
4610H-805-121/104L
4610H-805-151/104L
4610H-805-201/104L
805 Electrical Schematic and Application
R2
C
R1
Vcc
Line 8
Line 7
Line 6
Line 5
Line 4
10
Line 3
1
Line 2
804 Electrical Schematic and Application
Line 1
R
Ct
Ce
±2 % ±20 % ±20 % Bourns Part Number
50 Ω 0.01 μF 0.1 μF
4612M-804-500L
100 Ω 0.01 μF 0.1 μF
4612M-804-101L
Vee
Standard 804 Part Numbers
805 8, 10 and 12 Pin SIP 100K ECL
(4610H-805-ZoC/CCL)
Designed to terminate 6 to 10 transmission lines using Thevenin equivalent
parallel termination techniques in
systems using 100K ECL. Popular impedance values include 50, 70, 75, 80,
90, 100, 120, 150 or 200 ohms. Standard values for R1 and R2, based on
Zo, have been chosen to accommodate
100K ECL designs. A 0.1 μF capacitor is
provided to reduce cross talk noise
within the network package. Values for
Zo and C not shown in the following
table are available on a custom basis.
This type of termination is an alternative
to parallel termination used when a
separate Vtt power supply is not
available.
Model
(46 = Conformal SIP)
Number of Pins
(8, 10, 12)
Physical Config.
• H = High Profile
Electrical Configuration
• 803 • 805
Impedance Code
• First 2 digits are significant
• Third digit represents the number of
zeros to follow.
• Units = ohms
Capacitance Code
• First 2 digits are significant
• Third digit represents the number of zeros to
follow.
• Units = picofarads
Termination
L = Lead Free (Sn/Ag/Cu-plated)
Consult factory for other available options.
How To Order 804
46 12 M - 804 - 500 L
Model
(46 = Conformal SIP)
Number of Pins
Physical Config.
• M = Medium Profile
Electrical Configuration
Resistance Code
• First 2 digits are significant
• Third digit represents the number of
zeros to follow.
• Units = ohms
Termination
L = Lead Free (Sn/Ag/Cu-plated)
Consult factory for other available options.
REV. 04/10
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Similar pages