Click here for more information.

Q-MultiFlex™
Point-to-multipoint IP
Modulator / Multi-demodulator
OVERVIEW
The Q-MultiFlex™ offers a new, cost-effective
solution for point-to-multipoint IP satellite systems. The Q-MultiFlex™ supports a highlyefficient DVB-S2X shared outbound along with
up to 16 FastLink™ low-latency LDPC returns.
The network system can optionally be controlled
via our innovative Q-Net™ Bandwidth Manager,
supporting a wide range of centralised bandwidth management, network management, monitoring and reporting functions.
The Q-MultiFlex™ interoperates with low-cost Q
-Lite™ and Q-Flex™ remote network modems.
The Q-MultiFlex™ supports the most powerful
bandwidth-saving technology available.
Advanced Bandwidth-Efficient Features
Paired Carrier™ (using ViaSat’s patented
PCMA technology) overlays transmit and receive
carriers reducing satellite bandwidth by 50% .
DVB-S2X, the successor to the highly robust
and bandwidth-efficient DVB-S2, is supported
and includes support for spectral roll-off factors
as low as 5%.
ACM allows any otherwise unused link margin to
be converted into additional throughput.
Teledyne Paradise Datacom LLC
328 Innovation Blvd., Suite 100
State College, PA 16803 USA
Tel: 1 (814) 238-3450
Fax: 1 (814) 238-3829
1 OF 5
FEATURES
Star, mesh & hybrid point-to-multipoint IP
Modulator & up to 16 demodulators
Dual IF/L-band operation
Scalable to any network size
DVB-S2X shared outbound
FastLink™ low-latency LDPC returns
Data rates to 160Mbps outbound & inbound
XStream IP™ is an integrated suite of advanced IP optimization & traffic management features including TCP acceleration,
header & payload compression, dynamic
routing, traffic shaping, encryption & ACM
Optimized spectral roll-offs, down to 5%
Paired Carrier™ option
Optional Q-Net™ Bandwidth Manager
Supports low-cost Q-Lite™ & Q-Flex™
remote modems
LinkGuard™ signal-under-carrier
interference detection
Built-in spectrum and constellation monitors
DVB Carrier ID. Fully compliant with DVBCID standard
Markets and Applications
IP trunking and backhaul
Corporate networking
Mobile backhaul
Disaster recovery
Maritime communications
Cellular backhaul
www.paradisedata.com
Teledyne Paradise Datacom Ltd.
2&3 The Matchyns, London Road, Rivenhall End
Witham, Essex, CM8 3HA United Kingdom
Tel: +44(0) 1376 515636
Fax: +44(0) 1376 533764
213622 Issued 5 March 2015
Q-MultiFlex™
Point-to-multipoint IP Modulator / Multi-demodulator
Common Specifications
Modulator Specification
XStream IP™ Tier 1 (Tx only)
Frequency
Operating Modes
XStream IP™ is an integrated set of IP optimization
and traffic management features designed for maximum reliability and bandwidth efficiency. The following features are provided as a standard part of the
Modulator Option.
Traffic
Provides guaranteed throughput for
Shaping
priority traffic; supports Committed
and Burst Information Rates. Stream
classification uses one or more of:
VLAN ID, IP address, IEEE 802.1p
priority & Diffserv DSCP
IP-overSupports the transmission of IP
DVB
packets with/without Ethernet frames
Encapsulation over DVB-S2/DVB-S2X; encapsulates & decapsulates using our
highly-efficient Paradise XStream
Encapsulation (PXE)
Traffic
Interface
Network
Topologies
Impedance
Return Loss
Redundancy
IF: 50 to 90MHz & 100 to 180MHz
(resolution 100Hz) (BNC connector)
L-band: 950 to 2150MHz
(resolution 100Hz) (N-type connector)
Standard:
Single Ethernet Gigabit RJ45
Options:
4-port Gigabit Ethernet switch
(extends base modem Ethernet traffic
port with another 3 Ethernet ports,
creating 4-port switch)
Optical Gigabit Ethernet (Small FormFactor pluggable module supporting
all common optical standards)
Supports star, mesh and hybrid networks
IF: 50Ω/75Ω; L-band: 50Ω
IF: >18dB; L-band: >15dB
1:1 or up to 1:16 redundancy
Data Rate
(1bps resolution)
Symbol Rate
(1sps resolution)
DVB-S2X (EN 302 307-2)
DVB-S2 (EN 302 307-1)
FastLink™ Low-latency LDPC
DVB-S2X: 100kbps to 160Mbps
DVB-S2: 100kbps to 160Mbps
FastLink™: 18kbps to 100Mbps
DVB-S2X: 100ksps to 50Msps
DVB-S2: 100ksps to 50Msps
FastLink™: 18ksps to 40Msps
Output Power
(0.1dB resolution)
IF: 0 to –25dBm
L-band: 0 to –40dBm
Output Power
Stability/Accuracy
Stability: ±1.0dB, 0ºC to 50ºC
Accuracy: ±0.375dBm
Transmit Filter
Roll-off
DVB-S2/S2X:
5%, 10%, 15%, 20%, 25%, 35%
FastLink™:
5%, 10%, 15%, 20%, 25%, 35%
±2º maximum
XStream IP™ Tier 2 (Tx only)
Option
Demodulator Specification
Phase Accuracy
A demodulator add-on card supports 8 demodulators.
One demodulator card is fitted as standard and a second
can be optionally fitted, supporting up to 16 demodulators
in total. Demodulators are enabled in software in blocks of
4.
Amplitude
Accuracy
±0.2dB maximum
The Tier 2 option extends the transmit capabilities
provided by the XStream IP™ Tier 1 option.
Carrier
Suppression
-30dBc minimum
DVB-S2/S2X
ACM
Output
Phase Noise
As EN 302 307 & IESS-316
Harmonics &
Spurious
Better than –60dBc/ 4kHz in-band (at
0dBm to –30dBm output)
Transmit On/Off
Ratio
-65dBc minimum
BUC PSU Option
24V or 48V DC via IFL cable, 200W
BUC 10MHz
Reference
Via IFL cable; 10MHz ± 0.01 ppm;
3dBm ± 3dB
XStream IP™ Tier 3 (Tx and Rx)
Option
FSK Control
Allows monitor & control of a
compatible L-band BUC from the
modem via the Tx IFL cable
The following features apply to both transmit and
receive and can be used independently of XStream
IP™ Tier 1 and XStream IP™ Tier 2 options. The
Tier 3 option supports all demodulators for a single
price.
Header
Robust Header Compression (RFC
Compression
3095). Reduces Ethernet/IP/UDP/
TCP/RTP header sizes typically by
90%. 1-way packet processing limit:
60,000 pps; 2-way limit: 45,000 pps.
Includes Ethernet header compression (compresses 14-byte Ethernet
frame to typically one byte)
Payload
Uses Deflate algorithm (RFC 1951)
Compression
to compress TCP & UDP packets;
typical payload compression of 50%
The second card can optionally be fitted with none of the
demodulators enabled, thereby keeping the initial purchase price low but allowing for convenient expansion in
the future.
Demodulators
Standard: 4
Options: 8, 12 or 16 (total)
All inbound carriers must be within a
Operating
bandwidth of 72MHz
Bandwidth
FastLink™ Low-latency LDPC decoder
Operating
operated in Closed Network mode
Mode
Data Rate
Each inbound: 18kbps to 100Mbps
Total for all inbounds combined:
Up to 160Mbps
1bps resolution
Symbol Rate
Each inbound: 18ksps to 40Msps
Total for all inbounds combined:
Up to 40Msps
1sps resolution
Scrambling
FastLink™ scrambler
IF minimum:
Input Range
-115 + 10 log (symbol rate)
L-band minimum:
-130 + 10 log (symbol rate)
IF/L-band maximum:
-80 + 10 log (symbol rate)
Maximum
+10dBm
Composite
Wanted-toIF: -94 + 10 log (symbol rate)
Composite
L-band: -102 + 10 log (symbol rate)
Frequency
±1kHz to ±250kHz
Sweep Width
(1kHz steps)
Dependent on data rate and sweep
Acquisition
width
Time
Clock Tracking
±100ppm minimum
Range
Receive
5%, 10%, 15%, 20%, 25%, 35%
Spectral Roll-off
LNB 10MHz
Via IFL cable; 10MHz ± 0.01 ppm;
Reference
0dBm ± 3dB
LNB Voltage
Selectable 13V, 15V, 18V or 24V DC to
LNB via IFL cable; maximum 0.5A
2 OF 5
Ethernet: Standard Features
Bridging and
Static Routing
IPv4/IPv6
VLAN
Support
DHCP, SNMP
Web Server
IP Metrics
Ethernet MTU
Size
Trunking mode: Hardware Layer 2
bridge supporting 160Mbps bidirectional traffic (at up to 500,000
packets per second); zero jitter
Layer 2 bridge & Layer 3 router:
Software processing capability of
up to 150,000 packets per second
Dual IPV4/IPV6 TCP/IP supporting IPv4/
IPv6 bridging and routing
IEEE 802.1q VLAN access & trunking
modes
DHCP for automatic allocation of M&C IP
address. SNMP v1, v2c & v3
Modem web server M&C interface
• Time graphs show Tx, Rx throughput
(bps, pps); dropped, errored packet
counts
• Tables show absolute values for
throughput (pps, bps), dropped
packets, etc.
Standard: 10k bytes
Optical Ethernet: 16k bytes
DVB-S2/S2X
VCM
TCP
Acceleration
AAA RADIUS
Secure User
Login
AES-256
Encryption
Dynamically varies modcod with
varying link conditions in order to
maximise throughput for each remote site at all times by converting
unused link margin into additional
throughput; 100% link availability
Supports the transmission up to 16
IP streams. Each stream has its own
associated modcod for optimal persite throughput
Typical throughput level of 90% of
link capacity. Supports 10,000 concurrent accelerated TCP connections
(plus at least 40,000 unaccelerated
TCP connections) up to 100Mbps
Authentication, Authorisation & Accounting. Greater access control &
accountability. Replaces standard
modem login with user’s personal
company network login credentials
Provides bi-directional encryption.
Remotes can share a common encryption key or each can use a
unique key, ensuring different customer data is kept secure.
Supported on Q-MultiFlexE™ model
only. See separate Q-MultiFlexE™
datasheet
213622 Issued 5 March 2015
Q-MultiFlex™
Point-to-multipoint IP Modulator / Multi-demodulator
Paired Carrier™ Option
DVB-S2 Performance
Paired Carrier™
Eb/No (dB) for Normal (64k) frames at DVB-S2 QEF (Es/No in brackets)
(for DVB-S2X performance, see separate datasheet)
Paired Carrier
data rate
options
(30kHz to
54MHz occupied bandwidth)
Power
asymmetry
Symbol rate
asymmetry
Eb/No
degradation
Mobile
Operation
Transmit and receive carriers are
overlaid in the same space segment.
Echo cancellation techniques are used
to cancel the unwanted transmit carrier
leaving the wanted receive carrier
256kbps, 512kbps, 1024kbps,
2.5Mbps, 5Mbps, 10Mbps, 15Mbps,
20Mbps, 25Mbps, 30Mbps, 40Mbps,
50Mbps, 60Mbps, 80Mbps, 100Mbps
and 160Mbps traffic rate
-10dB to +10dB
Up to 12:1
Typically < 0.5dB
up to 0.7dB for 16QAM/16APSK;
up to 1dB for 32APSK
Uses GPS data to continually
recalculate position relative to satellite,
allowing uninterrupted operation in
mobile environments anywhere in
satellite footprint
Network Management
Standard Web
Browser UI
Q-NET™
Option
Modem
Compatibility
A built-in web server provides full web
browser monitoring and control
Q-NET™ is an innovative, scalable
bandwidth management system. It
supports centralized monitoring and
control of all hub and remote units in
the system through a single server.
See separate Q-NET™ datasheet for
more details
Q-NET™ and Q-MultiFlex™ are compatible with the use of Q-Flex™ and
Q-Lite™ satellite modems
Tx Forward Error Correction
DVB-S2X
Also includes
support as
listed under
‘DVB-S2’ below
DVB-S2X Lowlatency Mode
Paradise
proprietary
extension to
DVB-S2X
DVB-S2
FastLink™
Low-Latency
LDPC
3 OF 5
Normal Frame:
QPSK 13/45, 9/20, 11/20
8PSK 23/36, 25/36, 13/18
8APSK-L 5/9, 26/45
16APSK 26/45, 3/5, 28/45, 23/36,
25/36, 13/18, 7/9, 77/90
16APSK-L 5/9, 8/15, 1/2, 3/5, 2/3
32APSK 32/45, 11/15, 7/9
32APSK-L 2/3
64APSK 11/15, 7/9, 4/5, 5/6
64APSK-L 32/45
Short Frame:
QPSK 11/45, 4/15, 14/45, 7/15, 8/15,
32/45
8PSK 7/15, 8/15, 26/45, 32/45
16APSK 7/15, 8/15, 26/45, 3/5, 32/45
32APSK 2/3, 32/45
Very Short Frame: (Frame size of
5,400 bits, reducing latency to 33% of
standard DVB-S2 Short frame)
QPSK/8PSK/16APSK/32APSK 2/5,
7/15, 8/15, 3/5, 2/3, 11/15, 4/5,
13/15, 14/15
Ultra Short Frame: (Frame size of
3,240 bits, reducing latency to 20% of
standard DVB-S2 Short frame)
QPSK/8PSK/16APSK/32APSK 1/3,
4/9, 5/9, 2/3, 7/9, 8/9
QPSK 1/4, 1/3, 2/5, 1/2, 3/5, 2/3, 3/4,
4/5, 5/6, 8/9, 9/10
8PSK 3/5, 2/3, 3/4, 5/6, 8/9, 9/10
16APSK 2/3, 3/4, 4/5, 5/6, 8/9, 9/10
32APSK 3/4, 4/5, 5/6, 8/9, 9/10
BPSK 0.499
QPSK/OQPSK 0.532, 0.639, 0.710,
0.798
8PSK/8QAM 0.639, 0.710, 0.778
16APSK/16QAM 0.726, 0.778, 0.828,
0.851
32APSK 0.778, 0.828, 0.886, 0.938
64QAM 0.828, 0.886, 0.938, 0.960
Rate
1/4
QPSK
8PSK
16APSK
Rate
1/3
Rate
2/5
1.5 (-1.6) 1.1 (-0.7) 1.3 (0.3)
Rate
1/2
Rate
3/5
Rate
2/3
1.5 (1.5)
2.1 (2.8)
3.3 (5.8)
2.2 (3.4)
4.0 (7.0)
5.1 (9.3)
Rate
3/4
Rate
4/5
Rate
5/6
2.6 (4.3)
3.0 (5.0)
3.1 (5.3)
4.7 (8.2)
5.7 (9.6)
5.8 (10.5) 6.6 (11.6) 7.0 (12.2)
Rate
8/9
Rate
9/10
3.8 (6.3)
6.7 (10.9)
7.9 (13.4)
4.1 (6.6)
7.0 (11.3)
8.2 (13.7)
8.2 (13.9) 8.8 (14.8) 9.2 (15.3) 10.1 (16.5) 10.4 (16.9)
32APSK
Note: the DVB-S2/S2X performance figures assume a Q-Flex™ or Q-Lite™ is being used as the
remote modem to receive the outbound carrier.
Rx Forward Error Correction
Test Facilities and Alarm Outputs
FastLink™
Low-Latency
LDPC
BER Tester
BPSK 0.499
QPSK/OQPSK 0.532, 0.639, 0.710,
0.798
8PSK/8QAM 0.639, 0.710, 0.778
16APSK/16QAM 0.726, 0.778, 0.828,
0.851
32APSK 0.778, 0.828, 0.886, 0.938
64QAM 0.828, 0.886, 0.938, 0.960
FastLink™ Performance
Eb/No (dB) at BER 5E-8 (Note: * denotes BER of 5E-12)
BPSK
0.499
2.9
(O)QPSK
0.532
2.6
(O)QPSK
0.639
2.8
(O)QPSK
0.710
3.2
(O)QPSK
0.798
3.9
Other test
modes
Alarm Relays
Demodulator-based bit error rate
tester, allowing the link from each
remote to be tested for data transparency. Supports various test patterns
compatible with common BER testers
Transmit CW
Transmit alternate 1-0 pattern
Simulated satellite delay for transmitted TCP/IP packets
4 independent Form C relays for unit,
deferred, Tx and aggregated Rx
alarms
DVB Carrier ID Option (ETSI TS 103
129)
Supports the identification of interfering carriers.
Allows identification of individual modem carriers by
superimposing a low-power CID waveform onto the
carrier with negligible degradation. The CID waveform
contains a unique Carrier ID and other identity information. A carrier monitoring system is required to
decode CID waveforms
8PSK
0.639
5.9*
8PSK
0.710
5.5
8PSK
0.778
6.1
8QAM
0.639
4.8
8QAM
0.710
5.3
Mechanical/Environmental
8QAM
0.778
5.9
Size
16APSK
0.726
7.5*
16APSK
0.778
7.1
16APSK
0.828
8.1
16APSK
0.851
8.3
16QAM
0.726
6.6
16QAM
0.778
7.1
16QAM
0.828
7.7
16QAM
0.851
8.0
32APSK
0.778
9.6
32APSK
0.828
10.6
32APSK
0.886
11.4
32APSK
0.938
13.2
Weight
Power
Supply
Compliances
Safety
Standards
Emissions &
Immunity
Operating
Temperature
Humidity
1U chassis, 410mm deep excluding
front panel handles and rear panel
connectors and fans
3.5kg
90 to 264VAC, 1A @100V, 0.5A @
240V, 47 to 63Hz
Fused IEC connector (live and neutral fused); 24V and 48V DC options
FCC, CE and RoHS compliant
EN60950-1:2006
Emissions: EN55022:2010 Class B
Immunity: EN55024:2010
Standard: 0 to 50ºC
(storage: -40ºC to 70ºC)
Extended: 0 to 55ºC when fitted with
Ruggedisation option
95% relative humidity, noncondensing
Built-in Spectrum
Analyser showing
LinkGuard™ SignalUnder-Carrier interference detection
without/with interferer
present.
213622 Issued 5 March 2015
Q-MultiFlex™
Point-to-multipoint IP Modulator / Multi-demodulator
Option
Description
Fully configurable - pay only for what you need!
Base Unit
Four demodulators with FastLink™ Low-latency LDPC Closed Network operation: BPSK, (O)QPSK, 8PSK,
8QAM, 16APSK, 16QAM, 32APSK, 64QAM; maximum aggregate receive data rate of 160Mbps/40Msps; 5%, 10%,
15% 20%, 25%, 35% spectral roll-off factors
Two Gigabit Ethernet RJ45s (for M&C and traffic); Ethernet bridge, static routing; IPv4/IPv6; 10k bytes MTU
IF demodulator operation 50 to 90MHz & 100 to 180MHz
L-band demodulator operation 950 to 2150MHz; high-stability 10MHz reference (for BUC/LNB); FSK
LinkGuard™: Signal-under-carrier interference detection web spectrum graph showing received spectrum and any
interference underneath the received carriers while on traffic; automated alarm when interference rises above user-set
threshold
Web browser monitoring tools: Spectrum display, constellation monitor, TCP/IP throughput
Internal Bit Error Rate Tester (BERT)
Modulator
Options
DVB-S2/S2X CCM Tx: Modulator transmit function to 160Mbps/50Msps; DVB-S2 QPSK, 8PSK, 16APSK & 32APSK Tx
operation per EN 302 307-1. DVB-S2X QPSK, 8PSK, 8APSK, 16APSK, 32APSK & 64APSK Tx operation per
EN 302 307-2. Includes 5%, 10%, 15%, 20%, 25% & 35% spectral roll-offs. Includes XStream IP™ Tier 1 (Tx only),
which comprises traffic shaping and IP-over-DVB encapsulation
DVB-S2X Low-latency Mode (proprietary extension to DVB-S2X):
Very Short Frame: Frame size of 5,400 bits, reducing latency to 33% of standard DVB-S2 Short frame; supports
QPSK/8PSK/16APSK/32APSK 2/5, 7/15, 8/15, 3/5, 2/3, 11/15, 4/5, 13/15, 14/15
Ultra Short Frame: Frame size of 3,240 bits, reducing latency to 20% of standard DVB-S2 Short frame; supports
QPSK/8PSK/16APSK/32APSK 1/3, 4/9, 5/9, 2/3, 7/9, 8/9
Low-cost DVB-S2 CCM Tx: (Reduces cost by providing only DVB-S2 operation.) Modulator transmit function to
160Mbps/50Msps; DVB-S2 QPSK, 8PSK, 16APSK & 32APSK Tx operation per EN 302 307-1.
Includes 15%, 20%, 25% & 35% spectral roll-offs
Includes XStream IP™ Tier 1 (Tx only), which comprises traffic shaping and IP-over-DVB encapsulation
FastLink™ Low-latency LDPC: Modulator transmit function to 100Mbps/40Msps; includes BPSK, QPSK, OQPSK,
8PSK, 8QAM, 16APSK, 16QAM, 32APSK & 64QAM; includes 5%, 10%, 15%, 20%, 25% & 35% spectral roll-offs
Demodulator
Options
8 demodulators: extends base operation from 4 demodulators to 8 demodulators
12 demodulators: extends operation from 8 demodulators to 12 demodulators
16 demodulators: extends operation from 12 demodulators to 16 demodulators
‘16 Demodulator Ready’ option: one demodulator add-on card is fitted as standard supporting up to 8 demodulators;
this option adds a second demodulator card to the unit but with none of the extra demodulators enabled by default in
order to keep the initial cost as low as possible. When required, the number of enabled demodulators can be expanded
conveniently (to either 12 or 16 demodulators) by entry of a software code without the need for a field hardware upgrade
XStream IP™
Options
XStream IP™ Tier 1 (Tx only): provided as standard with the Modulator Option; includes:
•
Traffic Shaping: CIR/BIR/priority settings for IP streams classified by VLAN ID, IP address, IEEE 802.1p priority
and Diffserv
•
IP-over-DVB Encapsulation: transmission of IP packets and Ethernet frames over DVB-S2/S2X using Paradise
XStream Encapsulation (PXE)
XStream IP™ Tier 2 (Tx only): requires Modulator Option; includes:
•
DVB-S2/S2X point-to-multipoint VCM (multiple streams in shared outbound, each controlled by its own modcod)
•
DVB-S2/S2X point-to-multipoint ACM (dynamic adjustment of all outbound modcods to maximize data rate)
XStream IP™ Tier 3 (Tx & Rx): applies to Tx and Rx; does not require XStream IP™ Tier 1 or Tier 2 options; supports
all enabled demodulators; includes:
•
Header Compression: IP/UDP/TCP/RTP packet header compression (RFC 3095) plus Ethernet header
compression
•
Payload Compression: TCP/UDP packet payload compression using the Deflate algorithm (RFC 1951)
•
TCP Acceleration: Supports up to 10,000 concurrent accelerated TCP connections at up to 100Mbps
•
AAA RADIUS Secure User Login: Authentication, Authorisation & Accounting. Greater access control &
accountability. Replaces standard modem login with user’s personal company network login credentials
•
AES-256 Encryption: Please note that AES-256 Encryption (TCP/IP packet payload encryption using AES with
256-bit keys) is supported on the Q-MultiFlexE™ model only. The Q-MultiFlexE™ is identical to the standard
Q-MultiFlex™ in every other respect
4 OF 5
Configuration options continue on next page.
213622 Issued 5 March 2015
Q-MultiFlex™
Point-to-multipoint IP Modulator / Multi-demodulator
Option
Description
Fully configurable - pay only for what you need!
Paired Carrier™
Paired Carrier™ add-on card P3607 (requires one or more options below)
Subject to prevailing
data rate limits.
Paired Carrier™ up to 256kbps (requires Paired Carrier™ add-on card)
Occupied bandwidth:
minimum 30kHz; maximum 54MHz
Extends Paired Carrier™ up to 1.024Mbps
Extends Paired Carrier™ up to 512kbps
Extends Paired Carrier™ up to 2.5Mbps
Extends Paired Carrier™ up to 5Mbps
Extends Paired Carrier™ up to 10Mbps
Extends Paired Carrier™ up to 15Mbps
Extends Paired Carrier™ up to 20Mbps
Extends Paired Carrier™ up to 25Mbps
Extends Paired Carrier™ up to 30Mbps
Paired Carrier™ is also
available as a low-cost 90
-day per annum license
for redundancy system
standby equipment please contact Sales for
details
Terrestrial Interfaces
Extends Paired Carrier™ up to 40Mbps
Extends Paired Carrier™ up to 50Mbps
Extends Paired Carrier™ up to 60Mbps
Extends Paired Carrier™ up to 80Mbps
Extends Paired Carrier™ up to 100Mbps
Extends Paired Carrier™ up to 160Mbps
4-port Gigabit Ethernet Switch: Extends base unit Ethernet traffic port with 3 Ethernet ports, creating 4-port switch
Optical Gigabit Ethernet: Small Form-factor Pluggable module; supports single-mode & multi-mode fibre & all wavelengths; supports all standard fibre connector types such as SC & LC (subject to provision of suitable mating socket for
SFP cage)
Ruggedisation
Ruggedises the equipment for harsh environments (fans with higher airflow, heatsinks on key components, etc.)
DVB-CID
DVB Carrier ID: Tx carrier identification per ETSI 103 129
Packet Synchronisation
Supports IEEE 1588 Precision Time Protocol Version 2, plus Simple Network Time Protocol
24V DC Input
K3023 24V DC primary power input (in place of 100 to 240V AC input); DC input attaches via a screw-terminal connector plate
48V DC Input
K3018 48V DC primary power input (in place of 100 to 240V AC input); DC input attaches via a screw-terminal connector plate
24V 200W BUC PSU
P3543 AC input, 24V 200W DC to Tx BUC
48V 200W BUC PSU
P3544 AC input, 48V 200W DC to Tx BUC
48V In & 24V BUC PSU
P3545 Floating 48V DC input; +24V 200W DC to Tx BUC; DC input attaches via a screw-terminal connector plate
48V In & 48V BUC PSU
P3546 Floating 48V DC input; +48V 200W DC to Tx BUC; DC input attaches via a screw-terminal connector plate
+48V In & 48V BUC PSU
P3547 +48V DC input; +48V 200W DC to Tx BUC; DC input attaches via a screw-terminal connector plate
Teledyne Paradise Datacom reserves the right to change specifications of products described in this document at any time without notice and without obligation to notify any person of such changes.
Refer to the website or contact Sales or Customer Support for the latest product information. The information contained herein is classified EAR99 under the U.S. Export Administration Regulations. The
modem itself is classified ECCN 5A991.b.4 and is subject to U.S. Department of Commerce export control. Export re-export or diversion contrary to U.S. law is prohibited.
5 OF 5
213622 Issued 5 March 2015
Similar pages