CH-506TXL & RXL HDBaseT™ Lite HDMI over Single CAT5e/6/7 Extender Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document. Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from Cypress Technology. © Copyright 2011 by Cypress Technology. All Rights Reserved. Version 1.1 August 2011 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. • Do not attach the power supply cabling to building surfaces. • Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. • Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. • To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. REVISION HISTORY VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE VR0 12/12/11 Preliminary Release VS1 26/04/12 Updated format, diagrams and statements VS2 26/07/12 IR cable updated VR3 28/09/12 Add Lite Version VS4 04/07/13 Updated Figures/Diagram CONTENTS 1. Introduction�������������������������������������������� 1 2. Applications������������������������������������������� 1 3. Package Contents�������������������������������� 1 4. System Requirements���������������������������� 1 5. Features�������������������������������������������������� 2 6. Operation Controls and Functions������� 3 6.1 Transmitter Front and Rear Panels��3 6.2 Receiver Front and Rear Panels�����4 6.3 D-Sub 9-Pin Definitions���������������������5 6.4 IR Cable Pin Assignment�����������������5 7. Connection Diagram���������������������������� 6 8. Specifications���������������������������������������� 7 9. Acronyms����������������������������������������������� 8 1. INTRODUCTION This HDBaseT™ Lite HDMI over Single CAT5e/6/7 Transmitter and Receiver Set can send uncompressed audio/video over a single run of CAT5e/6/7 cable up to 60m (1080p) and has the added benefit of control through the built-in RS-232 and 2-way IR. 2. APPLICATIONS • Domestic HDMI installation • University lecturing systems • Retail showroom systems • Conference presentation and control 3. PACKAGE CONTENTS • 1×HDMI over Single CAT5e/6/7 Transmitter • 1×HDMI over Single CAT5e/6/7 Receiver • 1×IR Blaster • 1×IR Extender • 1×3.5 mm Mini-jack to RS-232 Female Cable • 1×3.5 mm Mini-jack to RS-232 Male Cable • 2×5 V/2.6 A DC Power Adaptor • Operation Manual 4. SYSTEM REQUIREMENTS HDMI source equipment such as a DVD or Blu-ray player and HDMI equipped display (TV or monitor). HDMI and CAT5e/5/7 connection cables. 1 5. FEATURES • HDMI including 3D and 4k×2k (Ultra HD) support, HDCP and DVI compliant • Supports HDCP repeater and CEC functions • Simultaneous transmission of uncompressed data over a single CAT5e/6/7 cable up to 60 m/196 ft (1080p@60 Hz/8-bit), 40m (3D) or 20m (4k×2k) • Supports HD resolutions up to 1080p@60Hz/36-bit and Ultra HD (4K×2K) • Audio support up to LPCM 7.1CH, Dolby TrueHD and DTS-HD Master Audio • Supports HDBaseT Lite Technology including 2-Way IR and RS-232 • Installation friendly Note: This system was tested with CAT6/23AWG cable. Results may vary with cables of different specifications. 2 6. OPERATION CONTROLS AND FUNCTIONS 6.1 Transmitter Front and Rear Panels Front IR2 Extender RS232 In 1 HDMI In DC 5V Power Link IR1 Blaster 2 3 Rear 7 Lite 4 5 6 CAT 5e /6 Out 8 1 RS232 In: Connect to a PC/laptop or RS-232 enabled device (with supplied 3.5 mm mini-jack to D-sub 9-pin adaptor) for the transmission of RS-232 commands. 2 IR2 Extender: Connect to the supplied IR extender cable for IR signal reception. Ensure that remote control being used is within the direct line-of-sight of the IR extender. 3 IR1 Blaster: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line-of-sight of the equipment to be controlled. 4 HDMI In: Connect to the HDMI source equipment such as a DVD or Blu-ray player. 5 DC 5V: Connect the 5 V DC power supply to the unit and plug the adaptor into an AC outlet. 6 Link LED: The yellow LED will illuminate when both the input and output CAT5e/6/7 signals are connected. 7 Power LED: This green LED will illuminate when the device is connected to a power supply. 8 CAT5e/6 Out: Connect to the receiver unit with a single CAT5e/6/7 cable for transmission of all data signals. 3 6.2 Receiver Front and Rear Panels Front IR1 Extender RS232 Out 1 HDMI Out DC 5V Power Link IR2 Blaster 2 3 Rear 7 Lite 4 5 6 CAT 5e /6 In 8 1 RS232 Out: Connect to the device that is to be controlled (with the supplied 3.5mm mini-jack to D-sub 9-pin adaptor) by RS-232 commands. 2 IR1 Extender: Connect to the supplied IR extender cable for IR signal reception. Ensure that the remote being used is within the direct line-of-sight of the IR extender. 3 IR2 Blaster: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line of sight of the equipment to be controlled. 4 HDMI Out: Connect to a HDMI equipped TV/monitor for display of the HDMI input source signal. 5 DC 5V: Plug the 5 V DC power supply into the unit and connect the adaptor to an AC outlet. 6 Link LED: The yellow LED will illuminate when both the input and output CAT5e/6/7 signals are connected. 7 Power LED: This green LED will illuminate when the device is connected to a power supply. 8 CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6/7 cable for transmission of all data signals. 4 6.3 D-Sub 9-Pin Definitions PIN DEFINE TX/RX 1 N/C 2 TxD/RxD 3 RxD/TxD 4 N/C 5 GND 6 N/C 7 N/C 8 N/C 9 N/C 6.4 IR Cable Pin Assignment IR Blaster 1 Power 5 V 2 IR Blaster Signal 3 NC IR Extender 1 IR Signal 2 Power 5 V 3 Grounding 5 7. CONNECTION DIAGRAM RS-232 Equipped PC or Notebook DVD/Blu-ray Player HDMI Input 1.5m 60° 3m 7m m 3m 60° IR Blaster 1 RS-232 IR2 Extender IR Extender 2 RS232 In HDMI In IR1 Blaster TX DC 5V Power Link CAT 5e /6 Out Power Supply CAT5e/6/7 Cable (60m) Power Supply DC 5V Power IR Extender 1 Link CAT 5e /6 In IR1 Extender RS232 Out HDMI Out RX IR2 Blaster IR Blaster 2 60° 1.5m 3m 7m m 60° 3m RS-232 RS-232 Device to be Controlled HDMI Output Display 6 8. SPECIFICATIONS Video Bandwidth 300 MHz/10.2 Gbps Transmitter Input Ports 1×HDMI, 1×IR Extender, 1×RS-232 Output Ports 1×CAT5e/6/7, 1×IR Blaster Receiver Input Ports 1×CAT5e/6/7, 1×IR Extender Output Ports 1×HDMI, 1×IR Blaster, 1×RS-232 CAT5e/6/7 Cable Up to 60 m Distance HDMI Cable Input 10 m@8-bit, 6 m@12-bit Distance HDMI Cable Output 10 m@8-bit, 6 m@12-bit Distance ESD Protection Human-body Model: ±8 kV (air-gap discharge) ±4 kV (contact discharge) Power Supply 5 V/2.6 A DC (US/EU standards, CE/FCC/ UL certified) IR Frequency 30 ~ 50 kHz Dimensions 71 mm (W)×79 mm (D)×23 mm (H)/Each Weight 240 g/TX, 245 g/RX Chassis Material Aluminum Color Black Operating Temperature 0 °C~40 °C/32 °F~104 °F Storage Temperature −20 °C ~ 60 °C/−4 °F~140 °F Relative Humidity 20~90 % RH (non-condensing) Power Consumption 3 W/TX, 6 W/RX 7 CAT5e/6/7 Cable Specification: LENGTH BANDWIDTH DATA RATE SUPPORTED VIDEO Up to Up to Up to HD Video 60 m 225 MHz 5.3 Gbps Up to 1080p@60 Hz/36-bit, 3D (data rate lower than 5.3 Gbps or bandwidth below 225 MHz). Up to Greater Greater Ultra HD Video 35 m than than 225 MHz 5.3 Gbps Up to 4K×2K@30 Hz. 9. ACRONYMS ACRONYM COMPLETE TERM CAT5e Category 5 Cable CAT6 Category 6 Cable CAT7 Category 7 Cable CEC Consumer Electronics Control DVI Digital Visual Interface HDCP High-bandwidth Digital Content Protection HDMI High Definition Multimedia Interface IR Infrared 8 CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.tw