INTERSIL HA4

HA-4741/883
TM
Quad Operational Amplifier
July 1994
Features
Description
• This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of
Paragraph 1.2.1.
The Intersil HA-4741/883, which contains four amplifiers on
a monolithic chip, provides a new measure of performance
for general purpose operational amplifiers. Each amplifier in
the HA-4741/883 has operating specifications that equal or
exceed those of the 741-type amplifier in all categories of
performance.
• Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9V/µs (Min)
• Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . 2.5MHz (Min)
The HA-4741/883 is well suited to applications requiring accurate signal processing by virtue of its low values of input offset
voltage (3mV max), input bias current (200nA max) and input
voltage noise (9nV/√Hz typ at 1kHz). The 2.5MHz bandwidth,
coupled with high open loop gain, allow the HA-4741/883 to be
used in designs requiring amplifiers of wideband signals, such
as audio amplifiers. Audio application is further enhanced by
the HA-4741/883’s negligible output crossover distortion.
These excellent dynamic characteristics also make the HA4741/883 ideal for a wide range of active filter designs. Performance integrity of multi-channel designs is assured by a high
level of amplifier-to-amplifier isolation (66dB at 10kHz).
• Input Offset Voltage. . . . . . . . . . . . . . . . . . . . 3mV (Max)
• Input Bias Current . . . . . . . . . . . . . . . . . . . 200nA (Max)
• Input Voltage Noise . . . . . . . . . . . . . . . . . 9nV/√Hz (Typ)
• No Crossover Distortion
• Standard Quad Pinout
Applications
• Universal Active Filters
• D3 Communications Filters
A wide range of supply voltages (±2V to ±20V) can be used
to power the HA-4741/883, making it compatible with almost
any system including battery-powered equipment.
• Audio Amplifiers
• Battery-Powered Equipment
Ordering Information
PART
NUMBER
TEMPERATURE
RANGE
PACKAGE
HA1-4741/883
-55oC to +125oC
14 Lead CerDIP
HA4-4741/883
-55oC to +125oC
20 Lead Ceramic LCC
Pinouts
3
12 +IN4
V+
4
11 V-
+IN2
5
-IN2
6
OUT2
7
+
-2
3 +-
10 +IN3
9
-IN3
8
OUT3
4
NC
5
V+
6
NC
7
+IN2
8
2
1 20 19
-IN4
3
-+
4
+ 1
18 +IN4
17 NC
16 V-
2
+ -
3
-+
15 NC
14 +IN3
9 10 11 12 13
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002. All Rights Reserved
1
-IN3
+IN1
+IN1
NC
13 -IN4
NC
4 +-
OUT3
+1
OUT1
2
-IN1
-IN1
14 OUT4
-IN2
1
OUT2
OUT1
OUT4
HA-4741/883
(CLCC)
TOP VIEW
HA-4741/883
(CERDIP)
TOP VIEW
Spec Number
511007-883
FN3704
Specifications HA-4741/883
Absolute Maximum Ratings
Thermal Information
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 40V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VOutput Current . . . . . . . . Indefinite (One Amplifier Shorted to GND)
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC
Thermal Resistance
θJA
θJC
CerDIP Package . . . . . . . . . . . . . . . . . . .
75oC/W
20oC/W
Ceramic LCC Package . . . . . . . . . . . . . .
65oC/W
15oC/W
Package Power Dissipation Limit at +75oC for TJ ≤ +175oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33W
Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W
Package Power Dissipation Derating Factor Above +75oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3mW/oC
Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . 15.4mW/oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
VINCM ≤ 1/2 (V+ - V-)
RL ≥ 2kΩ
Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC
Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V to ±15V
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: V SUPPLY = ±15V, RSOURCE = 100Ω, R LOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.
PARAMETERS
Input Offset Voltage
Input Bias Current
SYMBOL
VIO
+IB
-IB
Input Offset Current
Common Mode
Range
IIO
+CMR
+AVOL
-AVOL
Common Mode
Rejection Ratio
TEMPERATURE
MIN
MAX
UNITS
1
+25oC
-3
3
mV
2, 3
+125oC, -55oC
-5
5
mV
-200
200
nA
-325
325
nA
VCM = 0V
VCM = 0V,
+RS = 10kΩ,
-R S = 100Ω
VCM = 0V,
+RS = 100Ω,
-R S = 10kΩ
VCM = 0V,
+RS = 10kΩ,
-R S = 10kΩ
1
2, 3
+CMRR
-CMRR
∆VCM = -10V,
V+ = +5V, V- = -25V,
V OUT = -10V
∆VCM = +10V,
V+ = +25V, V- = -5V,
V OUT = +10V
+125oC,
-55oC
-200
200
nA
2, 3
+125oC, -55oC
-325
325
nA
1
+25oC
-30
30
nA
2, 3
+125oC, -55oC
-75
75
nA
1
+25oC
12
-
V
12
-
V
V+ = 27V, V- = -3V
VOUT = 0V and -10V,
RL = 2kΩ
+25 C
+25oC
V+ = 3V, V- = -27V
VOUT = 0V and +10V,
RL = 2kΩ
o
1
2, 3
-CMR
Large Signal Voltage
Gain
CONDITIONS
LIMITS
GROUP A
SUBGROUPS
+125oC,
-55oC
o
1
+25 C
-
-12
V
2, 3
+125oC, -55oC
-
-12
V
4
+25oC
50
-
kV/V
25
-
kV/V
50
-
kV/V
5, 6
4
+125oC,
-55oC
oC
+25
5, 6
+125oC, -55oC
25
-
kV/V
1
+25oC
80
-
dB
o
o
2, 3
+125 C, -55 C
74
-
dB
1
+25oC
80
-
dB
74
-
dB
2, 3
+125oC,
-55oC
Spec Number
2
511007-883
Specifications HA-4741/883
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
Device Tested at: V SUPPLY = ±15V, RSOURCE = 100Ω, R LOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.
PARAMETERS
Output Voltage
Swing
SYMBOL
+VOUT1
RL = 10kΩ
4
+25 C
VOUT = 0V, IOUT =
0mA
-ICC
Power Supply
Rejection Ratio
VOUT = 0V, IOUT =
0mA
∆VSUP = +5V,
V+ = +10V, V- = -15V,
V+ = +20V, V- = -15V
+PSRR
∆VSUP = -5V,
V+ = +15V, V- = -10V,
V+ = +15V, V- = -20V
-PSRR
-
V
12
-
V
5, 6
+125oC, -55oC
-
-12
V
4
+25oC
10
-
V
o
o
5, 6
+125 C, -55 C
10
-
V
4
+25oC
-
-10
V
5, 6
+125oC, -55oC
-
-10
V
5
-
mA
5
-
mA
o
4
+25 C
+125oC,
-55oC
4
+25oC
-
-5
mA
5, 6
+125oC, -55oC
-
-5
mA
-
5
mA
-
7
mA
VOUT = +10V
+ICC
12
V
5, 6
Quiescent Power
Supply Current
UNITS
-12
VOUT = -10V
-IOUT
-55oC
MAX
-
RL = 2kΩ
+IOUT
+125oC,
MIN
+25oC
RL = 2kΩ
-VOUT2
TEMPERATURE
4
RL = 10kΩ
+VOUT2
LIMITS
o
5, 6
-VOUT1
Output Current
CONDITIONS
GROUP A
SUBGROUPS
o
1
+25 C
2, 3
+125oC,
-55oC
1
+25oC
-5
-
mA
2, 3
+125oC, -55oC
-7
-
mA
1
+25oC
80
-
dB
o
o
2, 3
+125 C, -55 C
80
-
dB
1
+25oC
80
-
dB
2, 3
+125oC, -55oC
80
-
dB
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: VSUPPLY = ±15V, RSOURCE = 50Ω , RLOAD = 2kΩ, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified.
PARAMETERS
Slew Rate
Rise and Fall Time
Overshoot
Gain Bandwidth
Product (Small Signal)
SYMBOL
CONDITIONS
LIMITS
GROUP A
SUBGROUPS
TEMPERATURE
MIN
MAX
UNITS
+SR
VOUT = -5V to +5V
7
+25oC
0.9
-
V/µs
-SR
VOUT = +5V to -5V
7
+25oC
0.9
-
V/µs
o
TR
VOUT = 0 to +200mV
10% ≤ TR ≤ 90%
7
+25 C
-
140
ns
TF
VOUT = 0 to -200mV
10% ≤ TF ≤ 90%
7
+25oC
-
140
ns
+OS
VOUT = 0 to +200mV
7
+25oC
-
40
%
-OS
VOUT = 0 to -200mV
7
+25oC
-
40
%
7
+25oC
2.5
-
MHz
GBWP
VOUT = 50mV
Spec Number
3
511007-883
Specifications HA-4741/883
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Characterized at: VSUPPLY = ±15V, RLOAD = 5kΩ, CLOAD = 50pF, Unless Otherwise Specified.
LIMITS
PARAMETERS
SYMBOL
Differential Input Resistance
RIN
CONDITIONS
VCM = 0V
NOTES
TEMPERATURE
MIN
MAX
UNITS
1
+25oC
260
-
kΩ
1, 2
+25oC
14
-
kHz
Full Power
Bandwidth
FPBW
VPEAK = 10V
Minimum Closed Loop
Stable Gain
CLSG
RL = 2kΩ, CL = 50pF
1
-55oC to +125oC
1
-
V/V
Output Resistance
ROUT
Open Loop
1
+25oC
-
350
Ω
1, 3
-55oC to +125oC
-
180
mW
1
+25oC
-66
-
dB
Quiescent Power
Consumption
PC
VOUT = 0V, IOUT =
0mA
Channel Separation
CS
f = 10kHz, RS = 1kΩ
Referred to Input
AV = 100V/V,
VIN = 100mV PEAK
NOTES:
1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization
based upon data from multiple production runs which reflect lot to lot and within lot variation.
2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK).
3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.)
TABLE 4. ELECTRICAL TEST REQUIREMENTS
MIL-STD-883 TEST REQUIREMENTS
SUBGROUPS (SEE TABLES 1 AND 2)
Interim Electrical Parameters (Pre Burn-In)
1
Final Electrical Test Parameters
1 (Note 1), 2, 3, 4, 5, 6, 7
Group A Test Requirements
1, 2, 3, 4, 5, 6, 7
Groups C and D Endpoints
1
NOTE:
1. PDA applies to Subgroup 1 only.
Spec Number
4
511007-883
HA-4741/883
Die Characteristics
DIE DIMENSIONS:
87 x 75 x 19 mils ± 1 mils
2210 x 1910 x 483µm ± 25.4µm
METALLIZATION:
Type: Al, 1% Cu
Thickness: 16kÅ ± 2kÅ
GLASSIVATION:
Type: Nitride
Thickness: 7kÅ ± 0.7kÅ
WORST CASE CURRENT DENSITY:
1.68 x 105 A/cm 2
SUBSTRATE POTENTIAL (Powered Up): VTRANSISTOR COUNT: 72
PROCESS: Junction Isolated Bipolar/JFET
Metallization Mask Layout
HA-4741/883
-IN4
+IN4
V-
+IN3
-IN3
OUT3
OUT4
OUT2
OUT1
-IN1
+IN1
V+
+IN2
-IN2
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
Spec Number
5
511007-883