1F10 RECTRON THRU SEMICONDUCTOR TECHNICAL SPECIFICATION 1F18 FAST RECOVERY RECTIFIER VOLTAGE RANGE 1000 to 1800 Volts CURRENT 0.5 Ampere FEATURES * * * * * * Fast switching Low leakage Low forward voltage drop High current capability High currenf surge High reliability R-1 MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.19 gram .787 (20.0) MIN. .126 (3.2) .106 (2.7) .025 (0.65) DIA. .021 (0.55) .102 (2.6) DIA. .091 (2.3) .787 (20.0) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) SYMBOL 1F10 1F12 1F14 1F15 1F16 1F18 UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 1000 1200 1400 1500 1600 1800 Volts Maximum RMS Voltage VRMS 700 1000 840 1200 980 1400 1050 1500 1120 1600 1260 1800 Volts Volts Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 25 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range VDC IO 0.5 Amps I FSM 25 Amps CJ 15 T J , T STG -55 to + 150 pF 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 0.5A DC Maximum DC Reverse Current at Rated DC Blocking Voltage TA = 25 oC SYMBOL VF Maximum Full Load Reverse Current Full Cycle Average, .375” (9.5mm) lead length at T L = 55 oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Reverse Recovery Test Conditions: IF = 0.5A, IR = -1.0A, IRR =- 0.25A 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts 1F10 1F12 1F14 1.8 1F15 1F16 1F18 UNITS Volts 5.0 uAmps 100 uAmps IR trr 300 nSec 2002-12 RATING AND CHARACTERISTIC CURVES ( 1F10 THRU 1F18 ) PEAK FORWARD SURGE CURRENT, (A) 500 Single Phase Half Wave 60Hz Inductive or Resistive Load 400 10 1F 300 ~1 8 F1 AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 200 100 0 0 50 100 150 AMBIENT TEMPERATURE, ( 175 FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 35 30 8.3ms Single Half Sine-Wave (JEDEC Method) 25 20 15 10 5 0 1 10 ) NUMBER OF CYCLES AT 60Hz FIG. 3 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (+) 25 Vdc (approx) (-) (-) D.U.T PULSE 0 GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES:1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. -0.25A (+) -1.0A 1cm SET TIME BASE FOR 50/100 ns/cm RECTRON 100