R2500F RECTRON THRU SEMICONDUCTOR TECHNICAL SPECIFICATION R5000F HIGH VOLTAGE FAST RECOVERY RECTIFIER VOLTAGE RANGE 2500 to 5000 Volts CURRENT 0.2 Ampere FEATURES *Fast switching *Low leakage *High reliability *High current capability *High surge capability DO-15 MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.4 gram 1.0 (25.4) MIN. .034 (0.9) DIA. .028 (0.7) .300 (7.6) .230 (5.8) .140 (3.6) .104 (2.6) DIA. 1.0 (25.4) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) SYMBOL R2500F R3000F R4000F R5000F UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 2500 3000 4000 5000 Volts Maximum RMS Volts VRMS 1750 2100 2800 3500 Volts VDC 2500 3000 4000 5000 Volts Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 50 oC Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Operating and Storage Temperature Range IO 200 mAmps I FSM 30 Amps T J , T STG -55 to + 150 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 0.2A DC Maximum DC Reverse Current at Rated DC Blocking Voltage TA = 25oC SYMBOL R2500F R3000F VF 4.0 5.0 NOTES : Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A R5000F 6.5 UNITS Volts 5.0 uAmps 100 uAmps 500 nSec IR Maximum Full Load Reverse Current Average, Full Cycle .375” (9.5mm) lead length at TL = 55oC Maximum Reverse Recovery Time (Note) R4000F trr 2002-12 RATING AND CHARACTERISTIC CURVES ( R2500F THRU R5000F ) FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (mA) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 250 Single Phase Half Wave 60Hz Inductive or Resistive Load 200 150 100 50 0 0 50 100 150 AMBIENT TEMPERATURE, ( 175 60 50 8.3ms Single Half Sine-Wave (JEDEC Method) 40 30 20 10 0 1 2 ) 4 6 10 20 40 60 NUMBER OF CYCLES AT 60Hz FIG. 3 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (+) 25 Vdc (approx) (-) (-) D.U.T PULSE 0 GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES:1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. -0.25A (+) -1.0A 1cm SET TIME BASE FOR 50/100 ns/cm RECTRON 100