05h1-05h6.pdf

05H1
THRU
05H6
SURFACE MOUNT HIGH EFFICIENCY RECTIFIER
VOLTAGE RANGE 50 to 600 Volts CURRENT 0.5 Ampere
FEATURES
*
*
*
*
*
*
*
Low power loss, high efficiency
Low leakage
Low forward voltage
High current capability
High speed switching
High surge capability
High reliability
SOD-123F
MECHANICAL DATA
.114 (2.9)
* Epoxy: Device has UL flammability classification 94V-O
* Mounting position: Any
* Weight: 0.016 gram
.106 (2.7)
.035 (0.90)
.077 (1.95)
.028 (0.70)
.069 (1.75)
.008 (0.20)
.053 (1.35)
.047 (1.20)
.030 (0.75)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
.022 (0.55)
.150 (3.8)
Ratings at 25 o C ambient temperature unless otherwise specified.
.142 (3.6)
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Dimensions in inches and (millimeters)
MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted)
SYMBOL
05H1
05H2
05H3
05H4
05H5
05H6
UNITS
Maximum Recurrent Peak Reverse Voltage
RATINGS
VRRM
50
100
200
300
400
600
Volts
Maximum RMS Voltage
VRMS
35
70
140
210
280
420
Volts
VDC
50
100
200
300
400
600
Maximum DC Blocking Voltage
o
Volts
Maximum Average Forward Rectified Current at T A= 55 C
IO
0.5
Amps
Peak Forward Surge Current 8.3 ms single half sine-wave
superimposed on rated load (JEDEC method)
I FSM
15
Amps
RqJA
130
RqJL
30
Typical Thermal Resistance (Note 4)
Typical Junction Capacitance (Note 2)
CJ
Operating and Storage Temperature Range
0
15
T J, T STG
12
-55 to + 150
C/W
pF
0
C
o
ELECTRICAL CHARACTERISTICS (At TA = 25 C unless otherwise noted)
CHARACTERISTICS
Maximum Instantaneous Forward Voltage at 0.5A DC
Maximum DC Reverse Current
at Rated DC Blocking Voltage T A = 25o C
Maximum Full Load Reverse Current
Average, Full Cycle .375” (9.5mm) lead length at T L = 55oC
Maximum Reverse Recovery Time (Note 1)
NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A
2. Measured at 1 MH Z and applied reverse voltage of 4.0 volts
3. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”.
4. Thermal Resistance : Mounted on PCB.
SYMBOL
VF
05H1
05H2
05H3
05H4
1.0
05H5
1.3
05H6
UNITS
1.7
Volts
5.0
uAmps
100
uAmps
IR
trr
50
75
nSec
2006-11
RATING AND CHARACTERISTICS CURVES ( 05H1 THRU 05H6 )
50 W
NONINDUCTIVE
(+)
25 Vdc
(approx)
(-)
(-)
D.U.T
PULSE
GENERATOR
(NOTE 2)
1
NONINDUCTIVE
trr
+0.5A
10 W
NONINDUCTIVE
OSCILLOSCOPE
(NOTE 1)
0
-0.25A
(+)
NOTES: 1 Rise Time = 7ns max. Input Impedance =
1 megohm. 22pF.
-1.0A
2. Rise Time = 10ns max. Source Impedance =
50 ohms.
1cm
SET TIME BASE FOR 50/100 ns/cm
AVERAGE FORWARD CURRENT, (A)
1.0
0.5
Single Phase
Half Wave 60Hz
Resistive or
Inductive Load
0
0
25
50
75
100
125
150
AMBIENT TEMPERATURE, (OC)
FIG.2 TYPICAL FORWARD CURRENT
DERATING CURVE
175
INSTANTANEOUS REVERSE CURRENT, (mA)
FIG.1 TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC
100
TA = 100 OC
10
TA = 50 OC
1.0
TA = 25 OC
0.1
0.01
0
20
40
60
80
100
120
PERCENT OF RATED PEAK REVERSE VOLTAGE, (%)
FIG.3 TYPICAL REVERSE
CHARACTERISTICS
140
PEAK FORWARD SURGE CURRENT, (A)
10
0V
TJ = 25 OC
0V
50
/1
0
0/
20
1.0
0/
40
0.1
60
0V
30
0.01
Pulse Width=300mS
1% Duty Cycle
0.001
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
21
8.3ms Single Half Sine-Wave
(JEDED Method)
18
15
12
9
6
3
0
1
2
5
INSTANTANEOUS FORWARD VOLTAGE, (V)
10
100
60
40
20
05H
10
6
4
1
1~0
05H
5H5
6
TJ = 25 OC
0.1 0.2
50
100
FIG.5 MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
200
2
20
NUMBER OF CYCLES AT 60Hz
FIG.4 TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
JUNCTION CAPACITANCE, (pF)
INSTANTANEOUS FORWARD CURRENT, (A)
RATING AND CHARACTERISTICS CURVES ( 05H1 THRU 05H6 )
0.4
1.0
2
4
10
20
40
REVERSE VOLTAGE, (V)
FIG.6 TYPICAL JUNCTION CAPACITANCE
100
Mounting Pad Layout
0.030 MIN.
(0.75 MIN.)
0.035MIN.
(0.90 MIN.)
0.165
(4.19) REF
Dimensions in inches and (millimeters)
DISCLAIMER NOTICE
Rectron Inc reserves the right to make changes without notice to any product
specification herein, to make corrections, modifications, enhancements or other
changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information
contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or
use of any product or circuit.
Rectron products are not designed, intended or authorized for use in medical,
life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in
such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.
Similar pages