2U SAS JBOD Enclosure - July 24, 2015

2U SAS JBOD Enclosure
Configuration Guide
Introduction
This document contains product and configuration information that will enable you to configure your system. The
guide will ensure fast and proper configuration of your storage system.
July 24, 2015
Revision 4.0
NEC Corporation
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
Contents
TECHNICAL SPECIFICATION ........................................................................................ 3
Key Features .......................................................................................................................................... 3
Specification .......................................................................................................................................... 3
EXTERNAL VIEWS ......................................................................................................... 4
Front and Rear Views ........................................................................................................................... 4
Dimensions (mm) .................................................................................................................................. 8
2U 2.5-inch SAS JBOD Enclosure N8192-101F ............................................................................. 8
2U 3.5-inch SAS JBOD Enclosure N8192-102F ............................................................................. 9
2U 2.5-inch SAS JBOD Enclosure N8192-103F ........................................................................... 10
2U 3.5-inch SAS JBOD Enclosure N8192-104F ........................................................................... 11
UNIT CONFIGURATION ................................................................................................ 12
1
External Drive Configuration ...................................................................................................... 12
1.1 2U 2.5-inch SAS JBOD Enclosure (1) ................................................................................. 12
1.2 2U 2.5-inch SAS JBOD Enclosure (2) ................................................................................. 13
1.3 2U 2.5-inch SAS JBOD Enclosure (3) ................................................................................. 14
1.4 2U 3.5-inch SAS JBOD Enclosure (1) ................................................................................. 15
1.5 2U 3.5-inch SAS JBOD Enclosure (2) ................................................................................. 16
1.6 2U 3.5-inch SAS JBOD Enclosure (3) ................................................................................. 17
COPYRIGHT NOTICE AND LIABILITY DISCLAIMER ................................................. 18
REVISION HISTORY ..................................................................................................... 19
NEC Corporation
Revision 4.0 – July 24, 2015
2
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
Technical Specification
Key Features



Compact direct attached storage
Twenty four 2.5-inch or twelve 3.5-inch drive bays in 2U enclosure
Superior reliability with hot plug redundant power supplies and redundant fans
Specification
(1/2)
Model
2U SAS JBOD Enclosure
Part Number
Storage
N8192-101F
N8192-102F
Maximum Capacity
28.8 TB SAS
48 TB NL SAS
Hot Plug
Supported
Drive Bays
24
12
Interfaces
One SFF-8088 mini-SAS Connector
Redundant Power Supply
Standard, hot plug
Power Supply
Two hot plug PSU
100-240 VAC ± 10% 50 / 60 Hz ± 3 Hz
Maximum Power Consumption
300 Watt
Dimensions (W x D x H )
482.0 x 552.9 x 87.8 mm / 19.0 x 21.8 x 3.5 in (2U)
Weight (Maximum)
29 kg, 63.93 lbs.
Temperature, Relative Humidity
(non-condensing)
Operating: 10° to 35° C / 50° to 95° F, 20 to 80%
Non-Operating: -10° to 55° C / 14° to 131° F, 20 to 80%
310 Watt
(2/2)
Model
2U SAS JBOD Enclosure
Part Number
Storage
N8192-103F
N8192-104F
Maximum Capacity
43.2 TB SAS
72 TB NL SAS
Hot Plug
Supported
Drive Bays
24
12
Interfaces
One mini-SAS HD Connector
Redundant Power Supply
Standard, hot plug
Power Supply
Two hot plug PSU
100-240 VAC ± 10% 50 / 60 Hz ± 3 Hz
Maximum Power Consumption
330 Watt
Dimensions (W x D x H )
482.6 x 548.5 x 87.4 mm / 19.0 x 21.6 x 3.4 in (2U)
Weight (Maximum)
28 kg, 61.73 lbs.
Temperature, Relative Humidity
(non-condensing)
Operating: 5° to 40° C / 41° to 104° F, 10 to 80%
Non-Operating: -10° to 60° C / 14° to 140° F, 5 to 80%
NEC Corporation
Revision 4.0 – July 24, 2015
270 Watt
3
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
External Views
Front and Rear Views
Front View for N8192-101F and N8192-102F
2U 2.5-inch SAS JBOD Enclosure (N8192-101F)
E
F
A
B
C
D
G
2U 3.5-inch SAS JBOD Enclosure (N8192-102F)
E
F
A
B
C
D
G
Legend
A.
ID LED
E.
Hard Drive Activity LED
B.
Service LED
F.
Hard Drive Fault LED
C.
Power LED
G.
Drive Bays
D.
Standby LED
NEC Corporation
Revision 4.0 – July 24, 2015
4
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
Rear View for N8192-101F and N8192-102F
A
B
C
D E F G
H I J
K L
M
Legend
A.
Power Switch
H.
Controller Ready LED
B.
AC Inlet
I.
Controller Fault LED
C.
AC Power Good LED
J.
ID LED
D.
Power Fault LED
K.
SAS Link LED
E.
Service Action LED
L.
SAS Fault LED
F.
DC Power Good LED
M.
SFF-8088 mini-SAS Connector
G.
Standby Power Good LED
NEC Corporation
Revision 4.0 – July 24, 2015
5
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
Front View for N8192-103F and N8192-104F
2U 2.5-inch SAS JBOD Enclosure (N8192-103F)
E D
A
B
C
2U 3.5-inch SAS JBOD Enclosure (N8192-104F)
D
E
A
B
C
Legend
A.
ID LED(Not used)
D
Hard Drive Activity LED
B.
Service LED
E
Hard Drive Fault LED
C.
Power LED
NEC Corporation
Revision 4.0 – July 24, 2015
6
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
Rear View for N8192-103F and N8192-104F
I
J
K
A
B
M
L
C D E F G
H
N
Legend
A.
Power Switch
B.
H.
Debug port(Not used)
mini-SAS HD Connector(Not used)
I.
RDY LED
C.
mini-SAS HD Connector(Not used)
J.
AC IN LED
D.
mini-SAS HD Connector
K.
ALM LED
E.
Controller Ready LED
L.
AC Inlet
F.
Controller Fault LED
M.
SAS Link LED
ID LED(Not used)
N
SAS Fault LED
G.
NEC Corporation
Revision 4.0 – July 24, 2015
7
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
Dimensions (mm)
2U 2.5-inch SAS JBOD Enclosure N8192-101F
NEC Corporation
Revision 4.0 – July 24, 2015
8
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
2U 3.5-inch SAS JBOD Enclosure N8192-102F
NEC Corporation
Revision 4.0 – July 24, 2015
9
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
2U 2.5-inch SAS JBOD Enclosure N8192-103F
NEC Corporation
Revision 4.0 – July 24, 2015
10
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
2U 3.5-inch SAS JBOD Enclosure N8192-104F
NEC Corporation
Revision 4.0 – July 24, 2015
11
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
Unit Configuration
1 External Drive Configuration
1.1
2U 2.5-inch SAS JBOD Enclosure (1)
Category
Product Name / Description
Part Number
Storage Controller
Required
RAID Controller (512MB, RAID0/1/5/6)
LSI MegaRAID SAS 9285-8e
RAID0/1/5/6/10/50/60, 1GB, Ext. 8, PCIe 2.0 x8, SAS 6Gb/s,
SATA 6Gb/s
RAID Controller (1GB, RAID0/1/5/6)
LSI MegaRAID SAS 9286CV-8e
RAID0/1/5/6/10/50/60, 1GB, Ext. 8, PCIe 3.0 x8, SAS 6Gb/s,
SATA 6Gb/s, flash cache protection modules included
RAID Battery Backup Unit
for LSI MegaRAID SAS 9285-8e
External SATA Cable
2 m, 1 x SFF-8088 to 1 x SFF-8088
2U 2.5-inch SAS JBOD Enclosure
24 x 2.5-inch Hot-plug hard drive bays
Front Bezel
For N8192-101F/102F
300GB HDD
1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10000 rpm
450GB HDD
1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10000 rpm
600GB HDD
1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm
900GB HDD
1 x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm
1.2TB HDD
1 x 1.2 TB, SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm
N8103-160
RAID BBU
Recommended
Cable
1 to 2 Required
Enclosure
1 to 2 Required
Bezel
Drive
24 slots
available
N8103-161
N8103-162
K410-191(02)
N8192-101F
N8192-302F
N8192-501
N8192-502
N8192-503
N8192-504
N8192-508
NOTE:








Storage controllers must be compatible with the server connected.
The drive enclosures connected to one storage controller must be identical.
One drive enclosure can be connected to one port of storage controller.
Eight and more disk drives must be installed.
All hard drives within a RAID array should be of the same capacity and rotation speed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
It is recommended to set RAID array configuration drives less than eight in order to minimize the risk
of becoming multiple hard drives failure.
Any of RAID arrays cannot be used as a boot device.
NEC Corporation
Revision 4.0 – July 24, 2015
12
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
1.2
2U 2.5-inch SAS JBOD Enclosure (2)
Category
Product Name / Description
Part Number
Storage Controller
Required
RAID Controller (2GB, RAID0/1/5/6)
LSI MegaRAID SAS 9380-8e
RAID0/1/5/6/10/50/60, 2GB, Ext. 8, PCIe 3.0 x8, SAS 12Gb/s,
SATA 6Gb/s,
Flash cache protection modules included
External SATA Cable
2 m, 1 x SFF-8088 to 1 x SFF-8644
2U 2.5-inch SAS JBOD Enclosure
24 x 2.5-inch Hot-plug hard drive bays
Front Bezel
For N8192-101F/102F
300GB HDD
1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10000 rpm
450GB HDD
1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10000 rpm
600GB HDD
1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm
900GB HDD
1 x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm
1.2TB HDD
1 x 1.2 TB, SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm
N8103-179
Cable
1 to 2 Required
Enclosure
1 to 2 Required
Bezel
Drive
24 slots
available
K410-322(02)
N8192-101F
N8192-302F
N8192-501
N8192-502
N8192-503
N8192-504
N8192-508
NOTE:








Storage controllers must be compatible with the server connected.
The drive enclosures connected to one storage controller must be identical.
One drive enclosure can be connected to one port of storage controller.
Eight and more disk drives must be installed.
All hard drives within a RAID array should be of the same capacity and rotation speed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
It is recommended to set RAID array configuration drives less than eight in order to minimize the risk
of becoming multiple hard drives failure.
Any of RAID arrays cannot be used as a boot device.
NEC Corporation
Revision 4.0 – July 24, 2015
13
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
1.3
2U 2.5-inch SAS JBOD Enclosure (3)
Category
Product Name / Description
Part Number
Storage Controller
Required
RAID Controller (2GB, RAID0/1/5/6)
LSI MegaRAID SAS 9380-8e
RAID0/1/5/6/10/50/60, 2GB, Ext. 8, PCIe 3.0 x8, SAS 12Gb/s,
SATA 6Gb/s,
Flash cache protection modules included
External SATA Cable
2 m, SFF-8644 to SFF-8644
2U 2.5-inch SAS JBOD Enclosure
24 x 2.5-inch Hot-plug hard drive bays
Front Bezel
For N8192-103F/104F
600GB 10K Hot Plug 2.5-inch SAS HDD
For N8192-103F, 2.5-inch SAS 10K HDD, 12Gb/s, 512B sector
1.2TB 10K Hot Plug 2.5-inch SAS HDD
For N8192-103F, 2.5-inch SAS 10K HDD, 12Gb/s, 512B sector
1.8TB 10K Hot Plug 2.5-inch SAS HDD
For N8192-103F, 2.5-inch SAS 10K HDD, 12Gb/s, 4KB sector
N8103-179
Cable
1 to 2 Required
Enclosure
1 to 2 Required
Bezel
Drive
24 slots
available
SAS
HDD
(512B)
SAS
HDD
(4KB)
K410-333(02)
N8192-103F
N8192-303F
N8192-514
N8192-516
N8192-513
NOTE:









Storage controllers must be compatible with the server connected.
One drive enclosure can be connected to one port of storage controller.
The drive enclosures connected to one storage controller must be identical.
At least eight drives must be installed.
All hard drives within a RAID array should be of the same capacity and rotation speed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
It is recommended to set RAID array configuration drives less than eight in order to minimize the risk
of becoming multiple hard drives failure.
Any of RAID arrays cannot be used as a boot device.
When you select 4KB sector HDD, confirm whether your applications support hard drives with 4 KB
sector size. For more information, visit the NEC website at:
http://www.nec.com/en/global/prod/express/svropt/hdd/collateral/4KHDD_Precautions_EN.pdf

The 4KB sector drives are make-to-order products. Please consult your sales representative in regard
to production lead time.
NEC Corporation
Revision 4.0 – July 24, 2015
14
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
1.4
2U 3.5-inch SAS JBOD Enclosure (1)
Category
Product Name / Description
Part Number
Storage Controller
Required
RAID Controller (512MB, RAID0/1/5/6)
LSI MegaRAID SAS 9285-8e
RAID0/1/5/6/10/50/60, 1GB, Ext. 8, PCIe 2.0 x8, SAS 6Gb/s,
SATA 6Gb/s
RAID Controller (1GB, RAID0/1/5/6)
LSI MegaRAID SAS 9286CV-8e
RAID0/1/5/6/10/50/60, 1GB, Ext. 8, PCIe 3.0 x8, SAS 6Gb/s,
SATA 6Gb/s, flash cache protection modules included
RAID Battery Backup Unit
for N8103-160 LSI MegaRAID SAS 9285-8e
N8103-160
External SATA Cable
2 m, 1 x SFF-8088 to 1 x SFF-8088
2U 3.5-inch SAS JBOD Enclosure
12 x 3.5-inch Hot-plug hard drive bays
Front Bezel
For N8192-101F/102F
1TB 7.2K Hot Plug 3.5-inch NL SAS HDD
1 x 1 TB NL SAS HDD, 3.5-inch, 6Gb/s, 7,200 rpm
2TB 7.2K Hot Plug 3.5-inch NL SAS HDD
1 x 2 TB NL SAS HDD,32.5-inch, 6Gb/s, 7,200 rpm
3TB 7.2K Hot Plug 3.5-inch NL SAS HDD
1 x 3 TB NL SAS HDD, 3.5-inch, 6Gb/s, 7,200 rpm
4TB 7.2K Hot Plug 3.5-inch NL SAS HDD
1 x 4 TB, NL SAS HDD, 3.5-inch, 6Gb/s, 7,200 rpm
K410-191(02)
RAID BBU
Recommended for
N8103-160
Cable
1 to 2 Required
Enclosure
1 to 2 Required
Bezel
Drive
12 slots
available
N8103-161
N8103-162
N8192-102F
N8192-302F
N8192-505
N8192-506
N8192-507
N8192-509
NOTE:








Storage controllers must be compatible with the server connected.
The drive enclosures connected to one storage controller must be identical.
One drive enclosure can be connected to one port of storage controller.
Four or more disk drives must be installed.
All hard drives within a RAID array should be of the same capacity and rotation speed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
It is recommended to set RAID array configuration drives less than eight in order to minimize the risk
of becoming multiple hard drives failure.
Any of RAID arrays cannot be used as a boot device.
NEC Corporation
Revision 4.0 – July 24, 2015
15
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
1.5
2U 3.5-inch SAS JBOD Enclosure (2)
Category
Product Name / Description
Part Number
Storage Controller
Required
RAID Controller (2GB, RAID0/1/5/6)
LSI MegaRAID SAS 9380-8e
RAID0/1/5/6/10/50/60, 2GB, Ext. 8, PCIe 3.0 x8, SAS 12Gb/s,
SATA 6Gb/s,
Flash cache protection modules included
External SATA Cable
2 m, 1 x SFF-8088 to 1 x SFF-8644
2U 3.5-inch SAS JBOD Enclosure
12 x 3.5-inch Hot-plug hard drive bays
Front Bezel
For N8192-101F/102F
1TB 7.2K Hot Plug 3.5-inch NL SAS HDD
1 x 1 TB NL SAS HDD, 3.5-inch, 6Gb/s, 7,200 rpm
2TB 7.2K Hot Plug 3.5-inch NL SAS HDD
1 x 2 TB NL SAS HDD,32.5-inch, 6Gb/s, 7,200 rpm
3TB 7.2K Hot Plug 3.5-inch NL SAS HDD
1 x 3 TB NL SAS HDD, 3.5-inch, 6Gb/s, 7,200 rpm
4TB 7.2K Hot Plug 3.5-inch NL SAS HDD
1 x 4 TB, NL SAS HDD, 3.5-inch, 6Gb/s, 7,200 rpm
N8103-179
Cable
1 to 2 Required
Enclosure
1 to 2 Required
Bezel
Drive
12 slots
available
K410-322(02)
N8192-102F
N8192-302F
N8192-505
N8192-506
N8192-507
N8192-509
NOTE:








Storage controllers must be compatible with the server connected.
The drive enclosures connected to one storage controller must be identical.
One drive enclosure can be connected to one port of storage controller.
Four or more disk drives must be installed.
All hard drives within a RAID array should be of the same capacity and rotation speed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
It is recommended to set RAID array configuration drives less than eight in order to minimize the risk
of becoming multiple hard drives failure.
Any of RAID arrays cannot be used as a boot device.
NEC Corporation
Revision 4.0 – July 24, 2015
16
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
1.6
2U 3.5-inch SAS JBOD Enclosure (3)
Category
Product Name / Description
Part Number
Storage Controller
Required
RAID Controller (2GB, RAID0/1/5/6)
LSI MegaRAID SAS 9380-8e
RAID0/1/5/6/10/50/60, 2GB, Ext. 8, PCIe 3.0 x8, SAS 12Gb/s,
SATA 6Gb/s,
Flash cache protection modules included
External SATA Cable
2 m, SFF-8644 to SFF-8644
2U 3.5-inch SAS JBOD Enclosure
12 x 3.5-inch Hot-plug hard drive bays
Front Bezel
For N8192-103F/104F
2TB 7.2K Hot Plug 3.5-inch NL SAS HDD
For N8192-104F, 3.5-inch NL-SAS 7.2K HDD, 6Gb/s, 512B sector
4TB 7.2K Hot Plug 3.5-inch NL SAS HDD
For N8192-104F, 3.5-inch NL-SAS 7.2K HDD, 6Gb/s, 512B sector
6TB 7.2K Hot Plug 3.5-inch NL SAS HDD
For N8192-104F, 3.5-inch NL-SAS 7.2K HDD, 6Gb/s, 4KB sector
N8103-179
Cable
1 to 2 Required
Enclosure
1 to 2 Required
Bezel
Drive
12 slots
available
SAS
HDD
(512B)
SAS
HDD
(4KB)
K410-333(02)
N8192-104F
N8192-303F
N8192-520
N8192-522
N8192-519
NOTE:









Storage controllers must be compatible with the server connected.
The drive enclosures connected to one storage controller must be identical.
One drive enclosure can be connected to one port of storage controller.
At least four drives must be installed.
All hard drives within a RAID array should be of the same capacity and rotation speed.
To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in
order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process.
It is recommended to set RAID array configuration drives less than eight in order to minimize the risk
of becoming multiple hard drives failure.
Any of RAID arrays cannot be used as a boot device.
When you select 4KB sector HDD, confirm whether your applications support hard drives with 4 KB
sector size. For more information, visit the NEC website at:
http://www.nec.com/en/global/prod/express/svropt/hdd/collateral/4KHDD_Precautions_EN.pdf

The 4KB sector drives are make-to-order products. Please consult your sales representative in regard
to production lead time.
NEC Corporation
Revision 4.0 – July 24, 2015
17
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
Copyright Notice and Liability Disclaimer
The information contained herein is subject to change without notice.
All other products, brands, or trade names used in this document are trademarks or registered trademarks
of their respective holders.
NEC shall not be liable for technical or editorial errors or omissions contained herein.
NEC Corporation
Revision 4.0 – July 24, 2015
18
CONFIGURATION GUIDE – 2U SAS JBOD Enclosure
Revision History
Revision
Date
Description
4.0
July 24, 2015
New products added:
2U 2.5-inch SAS JBOD Enclosure N8192-103F
600GB 10K Hot Plug 2.5-inch SAS HDD N8192-514
1.2TB 10K Hot Plug 2.5-inch SAS HDD N8192-516
1.8TB 10K Hot Plug 2.5-inch SAS HDD N8192-513
2U 3.5-inch SAS JBOD Enclosure N8192-104F
2TB 7.2K Hot Plug 3.5-inch NL SAS HDD N8192-520
4TB 7.2K Hot Plug 3.5-inch NL SAS HDD N8192-522
6TB 7.2K Hot Plug 3.5-inch NL SAS HDD N8192-519
Front Bezel N8192-303F
External SATA Cable K410-333(02)
3.0
February 13, 2015
Other:
Corrected the type of SAS cable to connect with N8103-179 RAID Controller
and JBOD
2.0
January 30, 2015
New products added:
RAID Controller (2GB, RAID0/1/5/6) / N8103-179
1.0
December 26, 2013
Initial release
NEC Corporation
Revision 4.0 – July 24, 2015
19
Similar pages