INTERSIL ISL22329

ISL22329
®
Dual Digitally Controlled Potentiometers (XDCP™)
Data Sheet
September 4, 2009
Low Noise, Low Power, I2C™ Bus, 128 Taps,
Wiper Only
Features
The ISL22329 integrates two digitally controlled
potentiometers (DCP) and non-volatile memory on a
monolithic CMOS integrated circuit.
• 128 resistor taps
The digitally controlled potentiometers are implemented with
a combination of resistor elements and CMOS switches. The
position of the wipers are controlled by the user through the
I2C bus interface. Each potentiometer has an associated
volatile Wiper Register (WR) and a non-volatile Initial Value
Register (IVR) that can be directly written to and read by the
user. The contents of the WR controls the position of the
wiper. At power-up the device recalls the contents of the two
DCP’s IVR to the corresponding WRs.
FN6330.2
• Two potentiometers in one package
• I2C serial interface
- Three address pins, up to eight devices/bus
• Non-volatile storage of wiper position
• Wiper resistance: 70Ω typical @ 3.3V
• Shutdown mode
• Shutdown current 5µA max
• Power supply: 2.7V to 5.5V
• 50kΩ or 10kΩ total resistance
The DCPs can be used as a voltage divider in a wide variety
of applications including control, parameter adjustments, AC
measurement and signal processing.
• High reliability
- Endurance: 1,000,000 data changes per bit per register
- Register data retention: 50 years @ T < +55°C
Pinout
• 10 Ld MSOP
ISL22329
(10 LD MSOP)
TOP VIEW
• Pb-free (RoHS compliant)
A2
1
10
SCL
2
9
RW0
SHDN
SDA
3
8
VCC
GND
4
7
A1
RW1
5
6
A0
Ordering Information
PART NUMBER
(Note)
PART MARKING
RESISTANCE OPTION
(kΩ)
TEMP. RANGE
(°C)
PACKAGE
(Pb-free)
PKG. DWG. #
ISL22329UFU10Z*
329UZ
50
-40 to +125
10 Ld MSOP
M10.118
ISL22329WFU10Z*
329WZ
10
-40 to +125
10 Ld MSOP
M10.118
*Add “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100%
matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations).
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J
STD-020.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) and XDCP are registered trademarks of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2006, 2009. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ISL22329
Block Diagram
VCC
VCC
SCL
SDA
I2C
INTERFACE
A0
A1
POWER-UP
INTERFACE,
CONTROL
AND STATUS
LOGIC
WR1
A2
RW1
VCC
NONVOLATILE
REGISTERS
SHDN
WR0
RW0
GND
Pin Descriptions
MSOP PIN
SYMBOL
DESCRIPTION
Device address input for the I2C interface
1
A2
2
SCL
Open drain I2C interface clock input
3
SDA
Open drain serial data I/O for the I2C interface
4
GND
Device ground pin
5
RW1
“Wiper” terminal of DCP1
6
A0
Device address input for the I2C interface
7
A1
Device address input for the I2C interface
8
VCC
9
SHDN
Shutdown active low input
10
RW0
“Wiper” terminal of DCP0
2
Power supply pin
FN6330.2
September 4, 2009
ISL22329
Absolute Maximum Ratings
Thermal Information
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any Digital Interface Pin
with Respect to GND . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V
Voltage at any DCP Pin with Respect to GND. . . . . . . -0.3V to VCC
IW (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
Latchup (Note 2) . . . . . . . . . . . . . . . . . . Class II, Level B @ +125°C
ESD
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5kV
Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1kV
Thermal Resistance (Typical, Note 1)
θJA (°C/W)
10 Lead MSOP package . . . . . . . . . . . . . . . . . . . . .
120
Maximum Junction Temperature (Plastic Package). . . . . . . . +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
VCC Voltage for DCP Operation . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3mA to 3mA
Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2. Jedec Class II pulse conditions and failure criterion used. Level B exceptions are: using a max positive pulse of 6.5V on the SHDN pin, and using
a max negative pulse of -0.8V for all pins.
Analog Specifications
SYMBOL
RTOTAL
Over recommended operating conditions unless otherwise stated.
PARAMETER
End-to-End Resistance
TEST CONDITIONS
MIN
(Note 13)
TYP
(Note 3)
MAX
(Note 13)
UNIT
W option
10
kΩ
U option
50
kΩ
End-to-End Resistance Tolerance
W and U option
End-to-End Temperature Coefficient
W option
±50
ppm/°C
(Note 11)
U option
±80
ppm/°C
(Note 11)
VCC = 3.3V @ +25°C,
wiper current = VCC/RTOTAL
70
Ω
25
pF
RW
(Note 13)
Wiper Resistance
CW
(Note 11)
Wiper Capacitance
-20
+20
%
VOLTAGE DIVIDER MODE ( measured at RWi, unloaded; i = 0 or 1)
INL
(Note 8)
Integral Non-linearity
Monotonic over all tap positions
-1
1
LSB
(Note 4)
DNL
(Note 7)
Differential Non-linearity
Monotonic over all tap positions
-0.5
0.5
LSB
(Note 4)
ZSerror
(Note 5)
Zero-scale Error
W option
0
1
5
U option
0
0.5
2
LSB
(Note 4)
FSerror
(Note 6)
Full-scale Error
W option
-5
-1
0
U option
-2
-1
0
VMATCH
(Note 9)
DCP to DCP mAtching
Wipers at the same tap position
-2
TCV
(Note 10)
Ratiometric Temperature Coefficient
DCP register set to 40 hex
3
2
±4
LSB
(Note 4)
LSB
(Note 4)
ppm/°C
FN6330.2
September 4, 2009
ISL22329
Operating Specifications Over the recommended operating conditions unless otherwise specified.
SYMBOL
ICC1
ICC2
ISB
ISD
PARAMETER
TEST CONDITIONS
MIN
(Note 13)
TYP
(Note 3)
MAX
(Note 13)
UNIT
VCC Supply Current (volatile
write/read)
10k DCP, fSCL = 400kHz; (for I2C active,
read and write states)
1.4
mA
VCC Supply Current (volatile
write/read, non-volatile read)
50k DCP, fSCL = 400kHz; (for I2C active,
read and write states)
450
µA
VCC Supply Current ( non-volatile
write/read)
10k DCP, fSCL = 400kHz; (for I2C active,
read and write states)
3.5
mA
VCC Supply Current (non-volatile
write/read)
50k DCP, fSCL = 400kHz; (for I2C active,
read and write states)
2.0
mA
VCC Current (standby)
VCC = +5.5V , 10k DCP, I2C interface in
standby state
1.22
mA
VCC = +3.6V, 10k DCP, I2C interface in
standby state
800
µA
VCC = +5.5V, 50k DCP, I2C interface in
standby state
320
µA
VCC = +3.6V, 50k DCP, I2C interface in
standby state
250
µA
VCC = +5.5V @ +85°C, I2C interface in
standby state
3
µA
VCC = +5.5V @ +125°C, I2C interface in
standby state
5
µA
VCC = +3.6V @ +85°C, I2C interface in
standby state
2
µA
VCC = +3.6V @ +125°C, I2C interface in
standby state
4
µA
1
µA
VCC Current (shutdown)
Leakage Current, at Pins A0, A1, A2,
SHDN, SDA, and SCL
Voltage at pin from GND to VCC
tWRT
(Note 11)
DCP Wiper Response Time
SCL falling edge of last bit of DCP data byte
to wiper new position
1.5
µs
tShdnRec
(Note 11)
DCP Recall Time From Shutdown
Mode
From rising edge of SHDN signal to wiper
stored position and RH connection
1.5
µs
SCL falling edge of last bit of ACR data byte
to wiper stored position and RH connection
1.5
µs
ILkgDig
Vpor
Power-on Recall Voltage
VccRamp
VCC Ramp Rate
tD
Power-up Delay
Minimum VCC at which memory recall
occurs
-1
2.0
2.6
0.2
V
V/ms
3
VCC above Vpor, to DCP Initial Value
Register recall completed, and I2C Interface
in standby state
ms
EEPROM SPECIFICATION
EEPROM Endurance
EEPROM Retention
tWC
(Note 12)
Non-volatile Write Cycle Time
4
Temperature T < +55°C
1,000,000
Cycles
50
Years
12
20
ms
FN6330.2
September 4, 2009
ISL22329
Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued)
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
(Note 13)
TYP
(Note 3)
MAX
(Note 13)
UNIT
SERIAL INTERFACE SPECS
VIL
A2, A1, A0, SDA, and SCL Input
Buffer Low Voltage
-0.3
0.3*VCC
V
VIH
A2, A1, A0, SDA, and SCL Input
Buffer High Voltage
0.7*VCC
VCC +
0.3
V
Hysteresis
VOL
Cpin
(Note 10)
fSCL
SDA and SCL Input Buffer Hysteresis
0.05*
VCC
SDA Output Buffer LOW Voltage,
Sinking 4mA
V
0
A2, A1, A0, SDA, and SCL Pin
Capacitance
0.4
10
SCL Frequency
tsp
Pulse Width Suppression Time at
SDA and SCL Inputs
tAA
SCL Falling Edge to SDA Output Data SCL falling edge crossing 30% of VCC, until
Valid
SDA exits the 30% to 70% of VCC window
Any pulse narrower than the max spec is
suppressed
V
pF
400
kHz
50
ns
900
ns
tBUF
Time the Bus Must be Free Before the SDA crossing 70% of VCC during a STOP
Start of a New Transmission
condition, to SDA crossing 70% of VCC
during the following START condition
1300
ns
tLOW
Clock LOW Time
Measured at the 30% of VCC crossing
1300
ns
tHIGH
Clock HIGH Time
Measured at the 70% of VCC crossing
600
ns
tSU:STA
START Condition Setup Time
SCL rising edge to SDA falling edge; both
crossing 70% of VCC
600
ns
tHD:STA
START Condition Hold Time
From SDA falling edge crossing 30% of VCC
to SCL falling edge crossing 70% of VCC
600
ns
tSU:DAT
Input Data Setup Time
From SDA exiting the 30% to 70% of VCC
window, to SCL rising edge crossing 30% of
VCC
100
ns
tHD:DAT
Input Data Hold Time
From SCL rising edge crossing 70% of VCC
to SDA entering the 30% to 70% of VCC
window
0
ns
tSU:STO
STOP Condition Setup Time
From SCL rising edge crossing 70% of VCC,
to SDA rising edge crossing 30% of VCC
600
ns
tHD:STO
STOP Condition Hold Time for Read,
or Volatile Only Write
From SDA rising edge to SCL falling edge;
both crossing 70% of VCC
1300
ns
Output Data Hold Time
From SCL falling edge crossing 30% of VCC,
until SDA enters the 30% to 70% of VCC
window
0
ns
tR
SDA and SCL Rise Time
From 30% to 70% of VCC
20 +
0.1*Cb
250
ns
tF
SDA and SCL Fall Time
From 70% to 30% of VCC
20 +
0.1*Cb
250
ns
Cb
Capacitive Loading of SDA or SCL
Total on-chip and off-chip
10
400
pF
Rpu
SDA and SCL Bus Pull-up Resistor
Off-chip
Maximum is determined by tR and tF
For Cb = 400pF, max is about 2kΩ~2.5kΩ
For Cb = 40pF, max is about 15kΩ~20kΩ
1
tDH
5
kΩ
FN6330.2
September 4, 2009
ISL22329
Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued)
SYMBOL
PARAMETER
MIN
(Note 13)
TEST CONDITIONS
TYP
(Note 3)
MAX
(Note 13)
UNIT
tSU:A
A2, A1 and A0 Setup Time
Before START condition
600
ns
tHD:A
A2, A1 and A0 Hold Time
After STOP condition
600
ns
NOTES:
3. Typical values are for TA = +25°C and 3.3V supply voltage.
4. LSB: [V(RW)127 – V(RW)0]/127. V(RW)127 and V(RW)0 are V(RW) for the DCP register set to 7F hex and 00 hex respectively. LSB is the
incremental voltage when changing from one tap to an adjacent tap.
5. ZS error = V(RW)0/LSB.
6. FS error = [V(RW)127 – VCC]/LSB.
7. DNL = [V(RW)i – V(RW)i-1]/LSB-1, for i = 1 to 127. i is the DCP register setting.
8. INL = [V(RW)i – i • LSB – V(RW)0]/LSB for i = 1 to 127.
9. VMATCH = [V(RWx)i – V(RWy)i]/LSB, for i = 1 to 127, x = 0 to 1 and y = 0 to 1.
Max ( V ( RW ) i ) – Min ( V ( RW ) i )
10 6
10. TC V = ---------------------------------------------------------------------------------------------- × --------------------- for i = 16 to 112 decimal, T = -40°C to +125°C. Max() is the maximum value of the wiper
[ Max ( V ( RW ) i ) + Min ( V ( RW ) i ) ] ⁄ 2 +165°C voltage and Min () is the minimum value of the wiper voltage over the temperature range.
11. This parameter is not 100% tested.
12. tWC is the time from a valid STOP condition at the end of a Write sequence of I2C serial interface, to the end of the self-timed internal nonvolatile write cycle.
13. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
SDA vs SCL Timing
tHIGH
tF
SCL
tLOW
tHD:STO
tsp
tR
tSU:DAT
tSU:STA
tHD:DAT
tSU:STO
tHD:STA
SDA
(INPUT TIMING)
tAA
tDH
tBUF
SDA
(OUTPUT TIMING)
A0 and A1 Pin Timing
STOP
START
SCL
CLK 1
SDA
tSU:A
tHD:A
A0, A1
6
FN6330.2
September 4, 2009
ISL22329
Typical Performance Curves
100
1.2
T = +125°C
80
1.0
70
60
Isb (µA)
WIPER RESISITANCE (Ω)
1.4
VCC = 3.3V, T = +125°C
90
50
40
30
0.6
0.4
VCC = 3.3V, T = -40°C
VCC = 3.3V, T = +20°C
0.8
20
0.2
10
0
0
20
40
60
80
100
T = +25°C
0
2.7
120
3.2
3.7
TAP POSITION (DECIMAL)
0.2
5.2
0.2
T = +25°C
T = +25°C
VCC = 2.7V
0.1
0.1
INL (LSB)
DNL (LSB)
4.7
FIGURE 2. STANDBY ICC vs VCC
FIGURE 1. WIPER RESISTANCE vs TAP POSITION
[ I(RW) = VCC/RTOTAL ] FOR 10kΩ (W)
0
-0.1
VCC = 2.7V
0
-0.1
VCC = 5.5V
VCC = 5.5V
-0.2
4.2
VCC (V)
0
20
40
60
80
100
TAP POSITION (DECIMAL)
-0.2
120
FIGURE 3. DNL vs TAP POSITION IN VOLTAGE DIVIDER
MODE FOR 10kΩ (W)
20
40
60
80
100
TAP POSITION (DECIMAL)
120
FIGURE 4. INL vs TAP POSITION IN VOLTAGE DIVIDER
MODE FOR 10kΩ (W)
0.0
1.3
1.1
0
10k
-0.3
FSerror (LSB)
ZSerror (LSB)
0.9
0.7
0.5
VCC = 2.7V
VCC = 5.5V
0.3
VCC = 2.7V
50k
VCC = 5.5V
-0.6
-0.9
10k
0.1
-1.2
50k
-0.1
-0.3
-40
-20
0
20
40
60
TEMPERATURE (ºC)
80
FIGURE 5. ZSerror vs TEMPERATURE
7
100
120
-1.5
-40
-20
0
20
40
60
TEMPERATURE (ºC)
80
100
120
FIGURE 6. FSerror vs TEMPERATURE
FN6330.2
September 4, 2009
ISL22329
Typical Performance Curves
(Continued)
105
VCC = 2.7V
90
10
0.5
75
50k
TCv (ppm/°C)
END-TO-END RTOTAL CHANGE (%)
1.0
0.0
60
45
30
-0.5
50
10k
15
VCC = 5.5V
-1.0
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
100
120
FIGURE 7. END-TO-END RTOTAL % CHANGE vs
TEMPERATURE
0
16
36
56
76
TAP POSITION (DECIMAL)
96
FIGURE 8. TC FOR VOLTAGE DIVIDER MODE IN ppm
SCL
SIGNAL AT WIPER
(WIPER UNLOADED)
SIGNAL AT WIPER
(WIPER UNLOADED) MOVEMENT
FROM 7Fh TO 00h
FIGURE 9. MIDSCALE GLITCH, CODE 3Fh TO 40h
Pin Descriptions
FIGURE 10. LARGE SIGNAL SETTLING TIME
is still available in shutdown mode and all registers are
accessible. This pin must remain HIGH for normal operation.
Potentiometers Pins
RWI (I = 0,1)
RWi is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the WRi register.
RW
SHDN
The SHDN pin forces the resistors to end-to-end open circuit
condition and shorts all RWs to GND. When SHDN is
returned to logic high, the previous latch settings put RWi at
the same resistance setting prior to shutdown. This pin is
logically ANDed with SHDN bit in ACR register. I2C interface
8
FIGURE 11. DCP CONNECTION IN SHUTDOWN MODE
FN6330.2
September 4, 2009
ISL22329
Bus Interface Pins
SERIAL DATA INPUT/OUTPUT (SDA)
The SDA is a bi-directional serial data input/output pin for
I2C interface. It receives device address, operation code,
wiper address and data from an I2C external master device
at the rising edge of the serial clock SCL, and it shifts out
data after each falling edge of the serial clock.
SDA requires an external pull-up resistor, since it is an open
drain input/output.
SERIAL CLOCK (SCL)
This is the serial clock input of the I2C serial interface. SCL
requires an external pull-up resistor, since it is an open drain
input.
DEVICE ADDRESS (A2 - A0)
The address inputs are used to set the least significant 3 bits
of the 7-bit I2C interface slave address. A match in the slave
address serial data stream must match with the Address
input pins in order to initiate communication with the
ISL22329. A maximum of 8 ISL22329 devices may occupy
the I2C serial bus.
ones (127 decimal), the wiper moves monotonically from the
position closest to GND to the closest to VCC.
While the ISL22329 is being powered up, all WRs are reset
to 40h (64 decimal), which locates RW roughly at the center
between GND and VCC. After the power supply voltage
becomes large enough for reliable non-volatile memory
reading, all WRs will be reload with the value stored in
corresponding non-volatile Initial Value Registers (IVRs).
The WRs can be read or written to directly using the I2C
serial interface as described in the following sections. The
I2C interface Address Byte has to be set to 00h or 01h to
access the WR of DCP0 or DCP1 respectively.
Memory Description
The ISL22329 contains seven non-volatile and three volatile
8-bit registers. The memory map of ISL22329 is on Table 1.
The two non-volatile registers (IVRi) at address 0 and 1,
contain initial wiper value and volatile registers (WRi) contain
current wiper position. In addition, five non-volatile General
Purpose registers from address 2 to address 6 are available.
TABLE 1. MEMORY MAP
ADDRESS
NON-VOLATILE
VOLATILE
Principles of Operation
8
—
ACR
The ISL22329 is an integrated circuit incorporating two
DCPs with their associated registers, non-volatile memory
and an I2C serial interface providing direct communication
between a host and the potentiometers and memory. The
resistor arrays are comprised of individual resistors
connected in series. At either end of the array and between
each resistor is an electronic switch that transfers the
potential at that point to the wiper.
7
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions.
When the device is powered down, the last value stored in
IVRi will be maintained in the non-volatile memory. When
power is restored, the contents of the IVRi are recalled and
loaded into the corresponding WRi to set the wipers to the
initial value.
DCP Description
6
5
4
3
2
General Purpose
General Purpose
General Purpose
General Purpose
General Purpose
Not Available
Not Available
Not Available
Not Available
Not Available
1
0
IVR1
IVR0
WR1
WR0
The non-volatile IVRi and volatile WRi registers are
accessible with the same address.
The Access Control Register (ACR) contains information and
control bits described in Table 2. The VOL bit at access
control register (ACR[7]) determines whether the access is to
wiper registers WRi or initial value registers IVRi.
TABLE 2. ACCESS CONTROL REGISTER (ACR)
VOL
Each DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of each
DCP are equivalent to the fixed terminals of a mechanical
potentiometer and internally connected to Vcc and GND.
The RW pin of each DCP is connected to intermediate
nodes, and is equivalent to the wiper terminal of a
mechanical potentiometer. The position of the wiper terminal
within the DCP is controlled by volatile Wiper Register (WR).
Each DCP has its own WR. When the WR of a DCP contains
all zeroes (WR[6:0] = 00h), its wiper terminal (RW) is closest
to GND. When the WR register of a DCP contains all ones
(WR[6:0] = 7Fh), its wiper terminal (RW) is closest to VCC.
As the value of the WR increases from all zeroes (0) to all
9
Reserved
SHDN
WIP
0
0
0
0
0
If VOL bit is 0, the non-volatile IVRi registers are accessible.
If VOL bit is 1, only the volatile WRi are accessible. Note,
value is written to IVRi register also is written to the
corresponding WRi. The default value of this bit is 0.
The SHDN bit (ACR[6]) disables or enables Shutdown
mode. This bit is logically ANDed with SHDN pin. When this
bit is 0, DCPs are in Shutdown mode. Default value of SHDN
bit is 1.
FN6330.2
September 4, 2009
ISL22329
The WIP bit (ACR[5]) is read only bit. It indicates that
non-volatile write operation is in progress. It is impossible to
write to the IVRi, WRi or ACR while WIP bit is 1.
Shutdown Mode
The device can be put in Shutdown mode either by pulling the
SHDN pin to GND or setting the SHDN bit in the ACR register
to 0. The truth table for Shutdown mode is in Table 3.
TABLE 3.
SHDN pin
SHDN bit
Mode
High
1
Normal operation
Low
1
Shutdown
High
0
Shutdown
Low
0
Shutdown
I2C Serial Interface
The ISL22329 supports an I2C bidirectional bus oriented
protocol. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as the
receiver. The device controlling the transfer is a master and
the device being controlled is the slave. The master always
initiates data transfers and provides the clock for both
transmit and receive operations. Therefore, the ISL22329
operates as a slave device in all applications.
All communication over the I2C interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line must change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (See
Figure 12). On power-up of the ISL22329 the SDA pin is in
the input mode.
All I2C interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The ISL22329 continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition is met
(see Figure 12). A START condition is ignored during the
power-up of the device.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while
SCL is HIGH (see Figure 12). A STOP condition at the end
of a read operation, or at the end of a write operation places
the device in its standby mode.
An ACK, Acknowledge, is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (see Figure 13).
The ISL22329 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL22329 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation.
A valid Identification Byte contains 1010b as the four MSBs,
and the following three bits matching the logic values
present at pins A2, A1, and A0. The LSB is the Read/Write
bit. Its value is “1” for a Read operation, and “0” for a Write
operation (see Table 4).
TABLE 4. IDENTIFICATION BYTE FORMAT
Logic values at pins A2, A1, and A0 respectively
1
0
1
0
A2
(MSB)
A1
A0
R/W
(LSB)
SCL
SDA
START
DATA
STABLE
DATA
CHANGE
DATA
STABLE
STOP
FIGURE 12. VALID DATA CHANGES, START, AND STOP CONDITIONS
10
FN6330.2
September 4, 2009
ISL22329
SCL FROM
MASTER
1
8
9
SDA OUTPUT FROM
TRANSMITTER
HIGH IMPEDANCE
HIGH IMPEDANCE
SDA OUTPUT FROM
RECEIVER
START
ACK
FIGURE 13. ACKNOWLEDGE RESPONSE FROM RECEIVER
WRITE
S
T
A
R
T
SIGNALS FROM
THE MASTER
SIGNAL AT SDA
IDENTIFICATION
BYTE
ADDRESS
BYTE
1 0 1 0 A2 A1 A0 0
SIGNALS FROM
THE SLAVE
S
T
O
P
DATA
BYTE
0 0 0 0
A
C
K
A
C
K
A
C
K
FIGURE 14. BYTE WRITE SEQUENCE
SIGNALS
FROM THE
MASTER
S
T
A
R
T
SIGNAL AT SDA
IDENTIFICATION
BYTE WITH
R/W=0
ADDRESS
BYTE
1 0 1 0 A2 A1 A0 0
A
C
K
S
A T
C O
K P
A
C
K
1 0 1 0 A2 A1 A0 1
0 0 0 0
A
C
K
SIGNALS FROM
THE SLAVE
S
T
A IDENTIFICATION
R
BYTE WITH
T
R/W = 1
A
C
K
A
C
K
FIRST READ
DATA BYTE
LAST READ
DATA BYTE
FIGURE 15. READ SEQUENCE
11
FN6330.2
September 4, 2009
ISL22329
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL22329 responds with an ACK. At this time, the device
enters its standby state (See Figure 14). Device can receive
more than one byte of data by auto incrementing the
address after each received byte. Note after reaching the
address 08h, the internal pointer “rolls over” to address 00h.
Non-volatile write cycle starts after STOP condition is
determined and it requires up to 20ms delay for the next
non-volatile write. Thus, non-volatile registers must be
written individually.
Read Operation
A Read operation consist of a three byte instruction followed
by one or more Data Bytes (See Figure 15). The master
initiates the operation issuing the following sequence: a
START, the Identification byte with the R/W bit set to “0”, an
Address Byte, a second START, and a second Identification
byte with the R/W bit set to “1”. After each of the three bytes,
the ISL22329 responds with an ACK. Then the ISL22329
transmits Data Bytes as long as the master responds with an
12
ACK during the SCL cycle following the eighth bit of each
byte. The Data Bytes are from the registers indicated by an
internal pointer. This pointer initial value is determined by the
Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 08h, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.The master terminates the read
operation (issuing a ACK and STOP condition) following the
last bit of the last Data Byte (See Figure 15).
The Data Bytes are from the registers indicated by an
internal pointer. This pointer initial value is determined by the
Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 08h, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.
In order to read back the non-volatile IVR, it is recommended
that the application reads the ACR first to verify the WIP bit
is 0. If the WIP bit (ACR[5]) is not 0, the host should repeat
its reading sequence again.
FN6330.2
September 4, 2009
ISL22329
Mini Small Outline Plastic Packages (MSOP)
N
M10.118 (JEDEC MO-187BA)
10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE
E1
E
INCHES
SYMBOL
-B-
INDEX
AREA
1 2
0.20 (0.008)
A B C
TOP VIEW
4X θ
0.25
(0.010)
R1
R
GAUGE
PLANE
A
SEATING
PLANE -C-
A2
A1
b
-He
D
0.10 (0.004)
4X θ
L
SEATING
PLANE
C
-A0.20 (0.008)
C
C
a
SIDE VIEW
CL
E1
0.20 (0.008)
C D
-B-
MILLIMETERS
MAX
MIN
MAX
NOTES
A
0.037
0.043
0.94
1.10
-
A1
0.002
0.006
0.05
0.15
-
A2
0.030
0.037
0.75
0.95
-
b
0.007
0.011
0.18
0.27
9
c
0.004
0.008
0.09
0.20
-
D
0.116
0.120
2.95
3.05
3
E1
0.116
0.120
2.95
3.05
4
e
L1
MIN
0.020 BSC
0.50 BSC
-
E
0.187
0.199
4.75
5.05
-
L
0.016
0.028
0.40
0.70
6
L1
0.037 REF
0.95 REF
-
N
10
10
7
R
0.003
-
0.07
-
-
R1
0.003
-
0.07
-
-
θ
5o
15o
5o
15o
-
α
0o
6o
0o
6o
-
END VIEW
Rev. 0 12/02
NOTES:
1. These package dimensions are within allowable dimensions of
JEDEC MO-187BA.
2. Dimensioning and tolerancing per ANSI Y14.5M-1994.
3. Dimension “D” does not include mold flash, protrusions or gate
burrs and are measured at Datum Plane. Mold flash, protrusion
and gate burrs shall not exceed 0.15mm (0.006 inch) per side.
4. Dimension “E1” does not include interlead flash or protrusions
and are measured at Datum Plane. - H - Interlead flash and
protrusions shall not exceed 0.15mm (0.006 inch) per side.
5. Formed leads shall be planar with respect to one another within
0.10mm (.004) at seating Plane.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. Dimension “b” does not include dambar protrusion. Allowable
dambar protrusion shall be 0.08mm (0.003 inch) total in excess
of “b” dimension at maximum material condition. Minimum space
between protrusion and adjacent lead is 0.07mm (0.0027 inch).
10. Datums -A -H- .
and - B -
to be determined at Datum plane
11. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
13
FN6330.2
September 4, 2009