1MDC04015

RMT Ltd
Thermoelectric Module Datasheet
Performance Parameters
ΔTmax Qmax
K
W
Type
Imax
A
1MD04-015-XX
Umax AC R H
V
Ohm mm
H2*
mm
h
mm
1MD04-015-xx (N=15)
1MD04-015-03
69
2.5
2.3
0.57
0.9
1.4
0.9
1MD04-015-05
71
1.6
1.5
0.94
1.1
1.6
0.5
1MD04-015-08
72
1.0
1.0
1.51
1.4
1.9
0.8
1MD04-015-10
72
0.8
0.8
1.98
1.6
2.1
1.0
1MD04-015-12
72
0.7
0.7
2.26
1.8
2.3
1.2
1MD04-015-15
72
0.6
0.5
2.82
2.1
2.6
1.5
Performance data are given at 300K, vacuum
1.8
*Optional H2 value is specified for 0.5mm ceramics thickness
Technical Drawing
Options available
A. TEC Assembly:
Solder SnSb (Tmelt=230°C)
C. Ceramics Surface Options
D. Thermistor (optional)
1. Blank ceramics
Can be mounted to cold side
2. Metallized:
ceramics edge. Calibration
2.1 Ni / Sn(Bi)
B. Ceramics:
is available.
2.2 Gold plating
1.Pure Al2O3(100%)
3. Metallized and pre-tinned:
2.Alumina (Al2O3- 96%)
E. Terminal wires
3.1 Solder 94 (PbSnBi, Tmelt=94°C)
3.Aluminum Nitride (AlN)
1. Pre-tinned Copper
3.2 Solder 117 (In-Sn, Tmelt=117°C)
2. Insulated Wires
3.3 Solder 138 (Sn-Bi, Tmelt=138°C)
100% Al2O3 used as standard
3. Insulated Color Coded
3.4 Solder 183 (Pb-Sn, Tmelt=183°C)
4. Wire Bonding Pads
53 Leninskij prosp. Moscow 119991 Russia, ph: +7-499-132-6817, fax: +7-499-783-3664, web: www.rmtltd.ru
Copyright 2008. RMT Ltd. The design and specifications of products can be changed by RMT Ltd without notice.
Page 1 of 5
Performance Plots
1MD04-015-03
Temperature difference, K
RMT Ltd
Temperature difference, K
Thermoelectric Module Datasheet
Heat Pumped at the Cold Side, W
C.O.P
Voltage, V
Current, A
Temperature difference, K
Temperature difference, K
Performance Plots
Temperature difference, K
Temperature difference, K
1MD04-015-05
Heat Pumped at the Cold Side, W
C.O.P
Voltage, V
Current, A
Temperature difference, K
Temperature difference, K
Color Legend: Imax, 0.8 Imax, 0.6 Imax, 0.4 Imax
53 Leninskij prosp. Moscow 119991 Russia, ph: +7-499-132-6817, fax: +7-499-783-3664, web: www.rmtltd.ru
Copyright 2008. RMT Ltd. The design and specifications of products can be changed by RMT Ltd without notice.
Page 2 of 5
Performance Plots
1MD04-015-08
Temperature difference, K
RMT Ltd
Temperature difference, K
Thermoelectric Module Datasheet
Heat Pumped at the Cold Side, W
C.O.P
Voltage, V
Current, A
Temperature difference, K
Temperature difference, K
Performance Plots
Temperature difference, K
Temperature difference, K
1MD04-015-10
Heat Pumped at the Cold Side, W
C.O.P
Voltage, V
Current, A
Temperature difference, K
Temperature difference, K
Color Legend: Imax, 0.8 Imax, 0.6 Imax, 0.4 Imax
53 Leninskij prosp. Moscow 119991 Russia, ph: +7-499-132-6817, fax: +7-499-783-3664, web: www.rmtltd.ru
Copyright 2008. RMT Ltd. The design and specifications of products can be changed by RMT Ltd without notice.
Page 3 of 5
Performance Plots
1MD04-015-12
Temperature difference, K
RMT Ltd
Temperature difference, K
Thermoelectric Module Datasheet
Heat Pumped at the Cold Side, W
C.O.P
Voltage, V
Current, A
Temperature difference, K
Temperature difference, K
Performance Plots
Temperature difference, K
Temperature difference, K
1MD04-015-15
Heat Pumped at the Cold Side, W
C.O.P
Voltage, V
Current, A
Temperature difference, K
Temperature difference, K
Color Legend: Imax, 0.8 Imax, 0.6 Imax, 0.4 Imax
53 Leninskij prosp. Moscow 119991 Russia, ph: +7-499-132-6817, fax: +7-499-783-3664, web: www.rmtltd.ru
Copyright 2008. RMT Ltd. The design and specifications of products can be changed by RMT Ltd without notice.
Page 4 of 5
RMT Ltd
Thermoelectric Module Datasheet
Additional Options
TEC Polarity
TEC Polarity can be changed for free by request. The
specified in this datasheet polarity is typical.
It can be reversed without charge in accordance to
Customer application requirements.
-
+
+
-
WB Posts or Pads
WB pads or WB posts solutions are available. WB
pads (no posts) are provided as standard. WB Posts
solution is provided in accordance to Customer’s
demands and depending of TEC height.
WB Pads
WB Posts
Customized Au Patterns
Customized Au patterns solution on TEC cold side
ceramics is available. Selective Pre-tinning solution is
available. Please, contact us for additional
information about customized Au patterns
requirements.
Au Pattern
Pre-tinning
Application Tips
1. Never heat TE module more than 200˚C (TEC
assembled at 230˚C).
2. Never use TE module without attached heat sink
at hot (bottom) side.
3. Connect TE module to DC power supply
according to polarity.
4. Do not apply DC current higher than Imax.
Installation
1. Mechanical Mounting. TEC is placed between two heat exchangers . This construction is fixed by screws or
in another mechanical way. It is suitable for large modules (with dimensions 30x30mm and larger). Miniature
types require other assembling methods in most cases.
2. Soldering. This method is suitable for a TE module with metallized outside surfaces. RMT provides this
option and also makes pre-tinning for TE modules.
3. Glueing. It is an up-to-date method that is used by many customers due to availability of glues with good
thermoconductive properties. A glue is usually based on some epoxy compound filled with some
thermoconductive material such as graphite or diamond powders, silver, SiN and others. The application of
a specific type depends on application features and the type of a TE module.
Object being cooled
Object being cooled
TEC
TEC
1
3
2
Screw mounting
Heatsink
Soldering
Heatsink
Gluing
53 Leninskij prosp. Moscow 119991 Russia, ph: +7-499-132-6817, fax: +7-499-783-3664, web: www.rmtltd.ru
Copyright 2008. RMT Ltd. The design and specifications of products can be changed by RMT Ltd without notice.
Page 5 of 5
Similar pages