Download Specifications

Toggles
Series KP
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Pushbuttons
Programmable Illuminated PB
Keylocks
Rotaries
Slides
Tactiles
Tilt
Touch
Indicators
Accessories
Low Level:
100mA maximum @ 12V DC
Other Ratings
D
Contact Resistance: 200 milliohms maximum
Insulation Resistance: 100 megohms minimum @ 250V DC
Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum
1,500V AC minimum between contacts & case for 1 minute minimum
Mechanical Life: 5,000,000 operations minimum;
1,000,000 operations minimum for custom Rectangular Switch/Cap Assembly (at center of cap)
Electrical Life: 5,000,000 operations minimum
Nominal Operating Force: KP01: 1.9N maximum for Tactile & Nontactile models (at center of cap)
KP02: 1.6N maximum for Tactile, Nontactile & Tactile/Audible models (at center of cap)
Travel: KP01: Pretravel .122” (3.1mm); Overtravel .055” (1.4mm); Total Travel .177” (4.5mm)
KP02: Pretravel .091” (2.3mm); Overtravel .047” (1.2mm); Total Travel .138” (3.5mm)
Materials & Finishes
Plunger/Upper Housing:
Lower Housing:
Movable Contact:
Stationary Contacts:
Switch Terminals:
Environmental Data
Operating Temperature Range: Humidity: Vibration: Shock: Installation
Supplement
Miniature Audio/Video Pushbuttons
Cap Installation Force : PCB Processing
Soldering: Cleaning:
Standards & Certifications
Flammability Standards: D36
Polyacetal
Glass fiber reinforced PBT (UL94V-0)
Stainless steel with gold plating
Copper alloy with gold plating
Brass with gold plating
–25°C through +50°C (–13°F through +122°F)
90-95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
51G (500m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
50.0N maximum downward force on actuator
Wave Soldering. See Profile A in Supplement section.
Manual Soldering. See Profile A in Supplement section.
These devices are not process sealed. Hand clean locally using alcohol based solution.
UL94V-0 lower housing
The KP Series pushbuttons have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
www.nkk.com
Toggles
Series KP
Rockers
Distinctive Characteristics
Pushbuttons
KP series offers a complete switch solution for all broadcast panel needs,
including home keys and the custom rectangular switch/cap assembly.
Distinct, long total travel of .177” (4.5mm) for KP01 or shorter stroke
of .138” (3.5mm) for KP02.
D
Available with super bright red/green bicolor LED and
RGB LEDs. The RGB LED full color spectrum in a switch
package provides unlimited color combinations.
Keylocks
Specially designed snap-in standoff for simple and
secure PC board mounting and alignment.
Programmable Illuminated PB
Miniature Audio/Video Pushbuttons
Rotaries
Unique actuation guide gives positive indication
of circuit transfer as well as smooth and silent
operation. (Patent pending).
Slides
Choices of tactile, nontactile or tactile/audible
actuation.
Tactiles
Compact design with height of .906” (23.0mm)
from PC board to top of cap. (Same height as
programmable SmartSwitch™.)
Tilt
Flat, sculptured or home key square caps in three
common sizes for design flexibility in audio/video
applications.
Touch
Twin contacts with gold plating assure high reliability
and long life of 5,000,000 operations minimum.
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
D37
Series KP
Toggles
Miniature Audio/Video Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
Housing
K
Black only
D
15A
SPST
OFF
(ON)
( ) = Momentary
Normally Open Contacts
A
9.2mm Plunger
for 12.0mm Cap
B
11.6mm Plunger for
15.0mm & 17.4mm
Caps
6CF
RGB
Red/Green/Blue
(Custom)
Rotaries
Slides
01
Stroke: 4.5mm (.177”)
Actuation Force: 1.9N
02
Stroke: 3.5mm (.138”)
Actuation Force: 1.6N
Cap Colors
JB
Cap Types
Contacts & Terminals
Gold Contacts and
Straight PC Terminals;
100mA @ 12V DC
Actuation
Tactile
N
Nontactile
Tactiles
N
Nontactile
S
Tactile/Audible
3
17.4mm Square
Notes
*Custom RGB LED Page D42
**Custom Rectangular Cap Page D43
Touch
Indicators
Super Bright
Red/Green Bicolor LED
Nontactile Actuation
Accessories
Black Housing
Gold Contacts with 100mA Rating
Supplement
www.nkk.com
Home Key
** See Note
Straight PC Terminals
D38
T
15.0mm Square
KP0115ANBKG036CF-2SJB
SPST
OFF-Momentary ON Circuit
Normally Open Contacts
Sculptured
2
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
11.6mm Plunger and
15.0mm Sculptured Cap
Clear Lens and White Diffuser
S
12.0mm Square
Tilt
Tactile
Flat
1
02
C
F
Cap Sizes
01
C
Clear Lens
& White
Diffuser
* See Note
G03
Travel & Force
2 S JB
LEDs
Super Bright
Red/Green Bicolor
Plungers
Pole & Circuit
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
KP 01 15A N B K G03 6CF
Series KP
Toggles
Miniature Audio/Video Pushbuttons
POLE & CIRCUIT
Plunger Position
Normal
Down
OFF
(ON)
Normally
Open
1-1a
KP0115A
KP0215A
Note: Switch terminals “1” & “1a” are actually
marked on the switch.
1 (COM)
SPST
1a
ACTUATION
C
N
Tactile
KP01 or KP02
D
HOUSING
S
Nontactile
KP01 or KP02
K
Tactile/Audible
KP02 only
Black only
Straight PC Terminals 100mA @ 12V DC
Rotaries
Gold Contacts Keylocks
CONTACTS, TERMINALS, & RATING
G03
SUPER BRIGHT BICOLOR LED SPECIFICATIONS
6 CF
(–) L2
(+) COM
Green
LED circuit is isolated and
requires an external power
source.
If the source voltage exceeds
the rated voltage, a ballast
resistor is required.
The resistor value can be
calculated by using the
formula in the Supplement
section.
Red
Green
Unit
Minimum Luminous Intensity
IV
230
220
mcd
Standard Luminous Intensity
IV
290
270
mcd
Maximum Forward Current
I FM
30
(25 for Amber)
25
(22 for Amber)
mA
Typical Forward Current
IF
15
5
mA
Forward Voltage
VF
2.0
3.1
V
Power Peak Dissipation
PD
72
88
mW
Maximum Reverse Voltage
VRM
5
7
V
Wavelength at Peak Emission
λ
620 ~ 630
528 ~ 538
nm
Current Reduction Rate Above 25°C
∆I F
0.40
0.36
mA/°C
Ambient Temperature Range
–25 ~ +50
Tilt
Colors
Touch
LEDs are an integral part of
the switch and are not available separately.
Tactiles
(–) L1
Red
°C
Supplement
ATTENTION
Slides
The electrical specifications shown are determined at a basic temperature of 25°C.
ELECTROSTATIC
SENSITIVE DEVICES
Rockers
Down
Pushbuttons
Normal
Programmable Illuminated PB
SP
Model
Throw & Switch Schematic
Amber can be achieved by simultaneous illumination of Red & Green.
www.nkk.com
Indicators
Pole
Connected Terminals
Accessories
( ) = Momentary
D39
Series KP
Toggles
Miniature Audio/Video Pushbuttons
PLUNGERS
Rockers
A
Pushbuttons
Programmable Illuminated PB
B
(9.2)
.362
(6.4)
.252
9.2mm Plunger is designed
with a narrower neck to
hold the 12.0mm Cap.
D
1
12.0mm Square
F
(6.4)
.252
11.6mm Plunger is designed
with a wider neck to hold both
the 15.0mm and 17.4mm Caps.
S
AT3083 Flat Cap
T
AT3078 Sculptured Cap
(2.6) Dia
.102
(12.0) Sq
.472
2
15.0mm Square
Used on B Plunger
S
17.4mm Square
F
T
AT3079 Sculptured Cap
(7.0)
.276
3
(6.5)
.256
(12.0) Sq
.472
(12.0) Sq
.472
AT3084 Flat Cap
Slides
F
AT3086 Home Key Cap
(6.5)
.256
(6.5)
.256
Tilt
Tactiles
(11.6)
.457
Used on A Plunger
AT3087 Home Key Cap
(7.0)
.276
(7.0)
.276
(15.0) Sq
.591
(2.6) Dia
.102
(15.0) Sq
.591
(15.0) Sq
.591
Used on B Plunger
S
AT3085 Flat Cap
AT3088 Home Key Cap
(7.0)
.276
(7.0)
.276
(7.0)
.276
Touch
T
AT3080 Sculptured Cap
(2.6) Dia
.102
(17.4) Sq
.685
(17.4) Sq
.685
JB
Lens & Diffuser Colors Available:
Clear Lens
Clear/White
Accessories
Indicators
11.6mm Plunger
for 15.0mm & 17.4mm Caps
CAP TYPES & COLORS
Rotaries
Keylocks
9.2mm Plunger
for 12.0mm Cap
White Diffuser
Supplement
Materials & Finishes: Lens - Polycarbonate with glossy finish; Diffuser - Polycarbonate with textured finish
Optional Protective Guard AT4170 available; contact factory.
D40
www.nkk.com
(17.4) Sq
.685
Series KP
Toggles
Miniature Audio/Video Pushbuttons
TYPICAL SWITCH DIMENSIONS
Rockers
12.0mm Square Cap
(0.6) Typ
.024
COM
L2
(7.62)
.300
(1.3) Dia Typ
.051
1
(0.9) Dia Typ
.035
(0.6) Dia Typ
.024
1
(12.0) Sq
.472
(1.1)
.043
(6.5) (5.0)
(11.5)
.256 .197
.453
(23.0)
.906
1a
(4.5)
.177 (12.7)
.500
(0.25)
.010
(7.62)
.300
(0.37) Typ
.015
L1
1a
L1
C
L2
(5.08) +– 0.5
.200
(4.5)
.177 (12.7)
.500
D
(2.54) Typ
.100
(12.7)
.500
(15.0) Sq
.591
(6.0)
.236
Pushbuttons
(0.3)
.012
(12.7)
.500
KP0115ACAKG036CF-1SJB
15.0mm Square Cap
(0.6) Typ
.024
COM
L2
(7.62)
.300
(1.3) Dia Typ
.051
1
(0.9) Dia Typ
.035
(0.6) Dia Typ
.024
1
(15.0) Sq
.591
(1.1)
.043
(7.0) (4.5)
(11.5)
.276 .177
.453
(23.0)
.906
1a
(4.5)
.177 (12.7)
.500
(0.25)
.010
(7.62)
.300
(0.37) Typ
.015
L1
1a
L1
C
L2
(5.08) +– 0.5
.200
(4.5)
.177 (12.7)
.500
(2.54) Typ
.100
(12.7)
.500
(15.0) Sq
.591
(6.0)
.236
Rotaries
(0.3)
.012
Slides
(3.6)
.142
(12.7)
.500
Tactiles
(6.4)
.252
Programmable Illuminated PB
(3.6)
.142
Keylocks
(6.4)
.252
Tilt
KP0115ANBKG036CF-2SJB
(0.6) Typ
.024
L2
COM
(7.62)
.300
(1.3) Dia Typ
.051
(0.9) Dia Typ
.035
(0.6) Dia Typ
.024
1
(17.4) Sq
.685
(1.1)
.043
(11.5)
(7.0) (4.5)
.453
.276 .177
(23.0)
.906
1a
(4.5)
.177 (12.7)
.500
(0.25)
.010
(7.62)
.300
(0.37) Typ
.015
L1
1
1a
L1
C
(5.08) +– 0.5
.200
(6.0)
.236
(12.7)
.500
(15.0) Sq
.591
L2
Indicators
(0.3)
.012
(4.5)
.177 (12.7)
.500
(2.54) Typ
.100
Accessories
(3.6)
.142
(12.7)
.500
KP0115ANBKG036CF-3SJB
www.nkk.com
D41
Supplement
(6.4)
.252
Touch
17.4mm Square Cap
Series KP
Toggles
Miniature Audio/Video Pushbuttons
CUSTOM RGB
Note: For applications that require
white illumination, contact factory.
ATTENTION
Common
Anode (+)
RGB
ELECTROSTATIC
SENSITIVE DEVICES
Green
Color
Red
Green
Blue
Unit
Maximum Forward Current
I FM
30
30
30
mA
Typical Forward Current
IF
20
14
9
mA
Forward Voltage
VF
2.0
2.9
2.9
V
Power Peak Dissipation
PD
60
80
80
mW
Maximum Reverse Voltage
VRM
5
5
5
V
Dominant Wavelength
λd
621.5
522.5
472.5
nm
Current Reduction Rate Above 25°C
∆ IF
0.50
0.50
0.50
mA/°C
Blue
Ambient Temperature Range
–25 ~ +50
12.0mm Square Cap with RGB LED
°C
Common Anode (+)
B(-)
(7.62)
.300
(0.3)
.012
(3.6)
.142
1
(6.4)
.252
Terminal Detail
R(-)
G(-)
(0.6) Typ
.024
(7.62)
.300
(1.3) Dia Typ
.051
1
Slides
(12.0) Sq
.472
(12.7)
.500
See Terminal
Detail
(0.9) Dia Typ
.035
(0.7) Dia Typ
.028
R(-) G(-)
(4.5)
.177 (12.7)
.500
(3.81)
.150
(12.7)
.500
(12.7)
.500
(15.0) Sq
.591
(4.0)
.157
1a
B(-) (+)
(1.52) Typ
.060
(1.52) Typ
.060
(0.2) Sq Typ
.008
(1.1)
.043
(11.5)
(6.5) (5.0)
.256 .197
.453
(23.0)
.906
(4.5)
.177
1
(3.81)
.150
1a
Tactiles
Red
TYPICAL SWITCH DIMENSIONS
Rotaries
D
The electrical specifications shown are
determined at a basic temperature of
25°C.
LEDs are an integral part of the switch
and are not available separately.
LED circuit is isolated and requires an
external power source.
If the source voltage exceeds the rated
voltage, a ballast resistor is required.
The resistor value can be calculated by
using the formula in the Supplement
Section.
1a
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
LED SPECIFICATIONS
KP0115ACAKG03RGB-1SJB
Tilt
15.0mm & 17.4mm Square Caps with RGB LED
Common Anode (+)
B(-)
Touch
R(-)
G(-)
(15.0) Sq
.591
KP0115ANBKG03RGB-2SJB
(6.4)
.252
(3.81)
.150
(17.4) Sq
.685
KP0115ANBKG03RGB-3SJB
D42
(1.1)
.043
(11.5)
(7.0) (4.5)
.276 .177
.453
(23.0)
.906
(7.62)
.300
(0.3)
.012
(3.6)
.142
(12.7)
.500
(0.2) Sq Typ
.008
(4.0)
.157
17.4mm Cap
www.nkk.com
(0.6) Typ
.024
1
Accessories
Indicators
Terminal Detail
1a
Supplement
1
1a
15.0mm Cap
(4.5)
.177
See Terminal
Detail
(1.52) Typ
.060
(12.7)
.500
(15.0) Sq
.591
(7.62)
.300
(1.3) Dia Typ
.051
1
(0.9) Dia Typ
.035
(0.7) Dia Typ
.028
1a
B(-) (+)
R(-) G(-)
(1.52) Typ
.060
(12.7)
.500
(4.5)
.177 (12.7)
.500
(3.81)
.150
Series KP
Toggles
Miniature Audio/Video Pushbuttons
CUSTOM RECTANGULAR CAP ASSEMBLY
Switch/Rectangular Cap Assembly
1
L–
1a
(0.6)
.024
(0.45) Sq Typ
.018
D
(0.3)
.012
(7.0)
.276
(17.4)
.685
(23.0)
.906
(12.7)
.500
(15.0) Sq
.591
(6.0)
.236
KP0115ACBKG03CJB for Tactile
KP0115ANBKG03CJB for Nontactile
See below for complete assembly of switch, LEDs and LED holders.
(+)
(-)
Color
Red
Unit
Maximum Forward Current
I FM
30
mA
Typical Forward Current
IF
20
mA
Forward Voltage
VF
2.0
V
Maximum Reverse Voltage
VRM
4
V
Dominant Wavelength
λd
623
nm
Current Reduction Rate Above 25°C
∆I F
0.32
mA/°C
–25 ~ +50
°C
Ambient Temperature Range
Rotaries
The electrical specifications shown are
determined at a basic temperature of 25°C.
Center LED is an integral part of the switch.
LEDs are not sold separately.
LED circuits are isolated and require an
external power source.
If the source voltage exceeds the rated
voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement Section.
Keylocks
LED SPECIFICATIONS
Tactiles
Contact factory for other LED colors.
ASSEMBLY & INSTALLATION INSTRUCTIONS
(0.9) Dia Typ
.035
(2.54)
.100
Cathode
LED
(4.5)
.177
Tilt
(3.1) Dia
.122
(1.3) Dia Typ
.051
(2.54)
.100
(5.9)
.232
(4.8)
.189
(6.7)
.264
(10.4)
.409
LED
One LED (in center of switch bottom) is an
integral part of the switch; the other 2 LEDs
and 2 LED Holders are packaged separately.
PCB
www.nkk.com
1
L–
1a
(0.8) Dia Typ
.031
(12.7)
.500
(7.62) (12.7) (22.86)
.300 .500 .900
(2.54)
.100
LED Holder
Switch/Rectangular Cap assembly has 3 LEDs
to achieve bright and even illumination.
Switch
L+
Touch
LED Holder
Footprint
Indicators
(12.7)
.500
Slides
(2.54)
.100
L+
1
Install LED into LED Holder
(quantity 2).
2
Solder LEDs and LED Holders
into PCB.
3
Solder switch into PCB making
sure that the two outer LEDs
and LED Holders clear the bottom side opening of the cap.
D43
Accessories
(7.62)
.300
Supplement
(12.7)
.500
(34.8)
1.370
Programmable Illuminated PB
Pushbuttons
(4.5)
.177
(3.6)
.142
Rockers
CAP ASSEMBLY DIMENSIONS
Toggles
Series KP
ASSEMBLY INSTRUCTIONS FOR SQUARE CAPS
Rockers
ATTENTION
Cap Orientation
ELECTROSTATIC
SENSITIVE DEVICES
Notch
Pushbuttons
As shown in the accompanying illustration, the cap and
plunger are designed with tabs and notches to assure proper
orientation of the cap on the switch.
D
Tab
Step
Plunger
Notches
Removal of Cap Assembly & Separation of Lens & Diffuser
Holding the switch tightly, pull the cap off the switch. Once the
cap assembly is released from the plunger, the lens and diffuser can
be separated.
Pry up the lens with fingernail or flat tip screwdriver inserted at
the step on the diffuser.
Keylocks
Programmable Illuminated PB
Miniature Audio/Video Pushbuttons
Installation or Replacement of Cap
Rotaries
Cap
Assembly
Supplement
Accessories
Indicators
Touch
Tilt
Tactiles
Slides
After aligning notches with tabs, join the lens and diffuser.
Hold the switch tightly without touching the terminals. Firmly
press the cap onto the plunger by applying pressure from one
side to the other until both are snapped together.
D44
www.nkk.com
Plunger
Switch
Series KP
Toggles
Miniature Audio/Video Pushbuttons
LEGENDS
Rockers
NKK Switches can provide custom legends for caps. Contact factory for more information.
Suggested Printable Areas for KP Lens
OP
ST
Printing on Diffuser
is not advisable.
Film
Insert
Diffuser
D
Custom Rectangular Cap Lens
Keylocks
Shaded areas are suggested printable areas for Lens.
Sculptured Cap Lens
(28.75)
1.132
(13.4) Sq
.528
(17.4) Sq
.685
(12.8) Sq
.504
(15.0) Sq
.591
(8.97) Dia
.353
(10.5) Dia
.413
(0.76) Typ
.030
(11.48) Dia
.452
(13.0) Dia
.512
(0.76) Typ
.030
(13.77) Dia
.542
(15.3) Dia
.602
(0.76) Typ
.030
(13.77)
.542
(15.3)
.602
(0.76) Typ
.030
Tactiles
(9.8) Sq
.386
(12.0) Sq
.472
Rotaries
(30.28)
1.192
Suggested Printable Areas for KP Film Insert
Shaded areas are suggested printable areas for Film Insert.
Custom Rectangular Film Insert
(0.5) R
.020
(0.76) Typ
.030
(11.28) Sq
.444
(12.8) Sq
.504
(0.76) Typ
.030
(11.88) Dia
.468
(13.4) Sq
.528
(0.76) Typ
.030
(8.28)Dia
.326
(9.8) Sq
.386
(0.76) Typ
.030
(11.28) Dia
.444
(12.8) Sq
.504
(0.76) Typ
.030
(11.88) Dia
.468
(13.4) Sq
.528
Touch
(0.5) R
.020
(0.5) R
.020
(0.5) R
.020
(28.75)
1.132
(33.0)
1.299
(0.76) Typ
.030
(13.77)
.542
(15.6)
.614
(0.91) Typ
.036
Film Insert Material and Thickness: Clear Polyester; 4 mil (100µ) maximum thickness
Supplement
(8.28) Sq
.326
(9.8) Sq
.386
(0.5) R
.020
(0.5) R
.020
(0.5) R
.020
(2.125) Typ
.084
Accessories
Sculptured or Home Key Cap Film Inserts
Flat Cap Film Inserts
Slides
Flat Cap Lens
Tilt
Laser Etch on clear lens, Screen Print, or Pad Print on lens.
Laser Print on film insert.
Epoxy based ink is recommended.
Programmable Illuminated PB
Recommended Methods:
Indicators
Pushbuttons
Lens
www.nkk.com
D45
Similar pages