Download Specifications

Toggles
Series LP01
Short Body Pushbuttons
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Pushbuttons
Programmable Illuminated PB
Keylocks
Rotaries
Slides
Power Level (silver):
Other Ratings
D
Contact Resistance: 50 milliohms maximum
Insulation Resistance: 200 megohms minimum @ 500V DC
Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum
1,500V AC minimum between contacts and case for 1 minute minimum
Mechanical Life: 500,000 operations minimum
Electrical Life: 50,000 operations minimum for 3A @ 125V/250V AC & 3A @ 30V DC
100,000 operations minimum for 1A @ 125V/250V AC & 1A @ 30V DC
Nominal Operating Force: 1.5N for Single Pole; 3.0N for Double Pole
Contact Timing: Nonshorting (break-before-make)
Travel: Total Travel .118” (3.0mm)
Materials & Finishes
Actuator: Polycarbonate
Housing: Bushing mount: Glass fiber reinforced polyamide (UL94V-0);
Snap in mount: Polybutylene terephthalate (PBT) (UL94V-0)
Base:
Glass fiber reinforced polyamide (UL94V-0)
Movable Contact: Phosphor bronze & silver with silver plating
Stationary Contacts: Common terminal: Phosphor bronze with silver plating;
Contact terminals: Phosphor bronze with tin & copper plating
Lamp Terminals: Phospher bronze with tin and copper plating
Tactiles
Environmental Data
Tilt
3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
Operating Temperature Range: Humidity: Vibration: Shock: –10°C through +50°C (+14°F through +122°F) for Illuminated
–25°C through +70°C (+13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Mounting Torque: 0.8Nm (7.08 lb • in)
Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section.
Cleaning: Hand clean locally with alcohol based solution
Standards & Certifications
Flammability Standards:
UL: UL94V-0 housing & base
File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” to end of part number to order UL recognized switch.
All single & double pole models recognized at 3A @ 125V/250V AC or 3A @ 30V DC.
Supplement
Accessories
Indicators
Touch
Installation
D66
www.nkk.com
Toggles
Series LP01
Rockers
Distinctive Characteristics
Pushbuttons
Environmentally friendly components and packaging materials meet RoHS Directive
restricting use of hazardous materials. Suited for lead-free soldering because of
heat resistant resin materials.
Smooth, slightly concave surface of cap designed to
fit fingertip. Unique design and construction of cap
prevents its removal and limits tampering.
D
Keylocks
Bright LED illumination in choice of red, green, or
amber through translucent white cap.
Programmable Illuminated PB
Short Body Pushbuttons
Rotaries
Short body of .551” (14.0mm) conserves
behind-panel space.
Slides
Combination solder lug and .110” quick
connect terminals.
Touch
Tilt
Tactiles
Crisp actuation and clear circuit status provided
by snap-action contact mechanism. Arc barrier
between movable contacts protects against crossover.
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
D67
Series LP01
Toggles
Short Body Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
1
5
Poles
C
C
1
SPDT
C
Bushing
2
DPDT
M
Snap-in
Housing
(ON)
K
LEDs
Black
( ) = Momentary
5C
Red
5D
Amber
5F
Green
IMPORTANT:
Rotaries
Cap Color
B
Nonilluminated
White
Nonilluminated Cap Colors
No
Nonilluminated
Code
Switches are supplied without UL & cULus markings unless
specified. UL & cULus recognized only when ordered with
marking on switch. Specific models, ratings, & ordering
instructions are noted on the General Specifications page.
Slides
B
Silver Rated
3A @ 125V AC/250V AC
W01
Solder Lug/
Quick Connect Terminals
Circuit
ON
5C
Contacts & Terminals
D
5
W01
K
Mounting Types
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
LP01
A
Black
C
Red
F
Green
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Tactiles
LP0115CCKW015CB
White Cap
Red LED
Tilt
SPDT
ON-(ON) Circuit
Bushing Mount
Black Housing
Touch
Silver Contacts
Rated 3A @ 125/250V AC;
Solder Lug/Quick Connect Terminals
POLES & CIRCUIT
Supplement
Accessories
Indicators
Plunger Position
( ) = Momentary
Connected Terminals
Throw & Power/Lamp Schematics
Normal
Down
Normal
Down
LP0115
ON
(ON)
1-3
1-2
LP0125
ON
(ON)
Pole
Model
SP
DP
Note: Terminal markings “COM, NO, NC, L,
+ and – ” are actually on the switch;
terminal numbers are not on the switch.
1 (COM)
D68
1-3
4-6
1-2
www.nkk.com
4-5
SPDT
DPDT
3
1 (COM)
3
L (+)
(-) L
L (+)
(-) L
2
2
4
6
5
Series LP01
Toggles
Short Body Pushbuttons
MOUNTING TYPES
M
Snap-in
.630” (16.0mm) Diameter
Rockers
Bushing
.669” (17.0mm) Diameter
Recommended
Panel Thickness:
0.2
(18.1) +– 0.0
.713
(1.7) +– 0.0
0.1
.067
0.2
(16.0) +– 0.0
Dia
.630
Pushbuttons
This mounting option is supplied with
a steel hexagon nut with nickel plating.
Recommended
Panel Thickness:
0.1
(7.5) –+ 0.0
.295
.079” ~ .256”
(2.0mm ~ 6.5mm)
.039” ~ .126”
(1.0mm ~ 3.2mm)
(17.3)
.681
(21.0) Min
.827
(25.0) Min
.984
Allow .984” (25.0mm) distance from center-to-center
between switches when mounted side-by-side.
D
0.2
(1.1) +– 0.0
R
.043
+ 0.2
– 0.0
Dia
Allow .827” (21.0mm) distance from center-to-center
between switches when mounted side-by-side.
K
Black
Keylocks
HOUSING
Housing available in black only. The one-piece body and bezel have a matte finish.
Solder Lug/
.110” (2.8mm) Quick Connect
Power Level
3A @ 125V AC/250V AC; 3A @ 30V DC
Epoxy Seal
(2.0)
.079
(2.8)
.110
(0.6) R
.024
(1.2)
.047
Thk = (0.5)
.020
Tactiles
Note: If used at 1A @ 125V AC/250V AC or 1A @ 30V DC,
electrical life will be 100,000 operations minimum.
(7.3)
.287
Slides
Silver
Rotaries
CONTACT MATERIALS, RATINGS, & TERMINALS
W01
LED COLORS & SPECIFICATIONS
5D
5F
Red
Amber
Green
Maximum Forward Current
I FM
30mA
30mA
30mA
Typical Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
1.95V
2.0V
2.1V
Maximum Reverse Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆I F
0.41mA/°C
0.29mA/°C
0.39mA/°C
No Code
–10°C ~ +50°C
Supplement
Ambient Temperature Range
Touch
Colors
5C
Indicators
LEDs are an
integral part
of the switch
and are not
available
separately.
(-)
Accessories
(+)
Tilt
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source. Polarity marks are on the switch.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Single Color LED with 1 Element
Programmable Illuminated PB
C
No Lamp
www.nkk.com
D69
Series LP01
Toggles
Short Body Pushbuttons
CAP COLORS
Illuminated Cap
Rockers
B
Pushbuttons
White
The translucent cap is an integral part of
the switch and is not available separately.
Material: Polycarbonate
A
C
Black
Red
F
Green
The cap is an integral part of the switch and is not available separately.
Material: Polycarbonate
Finish: Matte
Finish: Matte
TYPICAL SWITCH DIMENSIONS
Bushing Mount • Single Pole
(3.7)
.146
(1.2) x (2.0) Typ
.047 x .079
M16 P1
(0.5) Typ
.020
(9.7)
.382
(2.8) Typ
.110
LP0115CCKW015CB
(13.6) Dia
.535
(20.0) Dia
.787
(2.5)
.098
Bushing Mount • Double Pole
COM
(7.3)
.287
(3.0)
.118
(5.55)
.219
(3.7)
.146
(1.2) x (2.0) Typ
.047 x .079
M16 P1
(0.5) Typ
.020
NC
Slides
(2.8) Typ
.110
LP0125CCKW015CB
(2.5)
.098
(13.6) Dia
.535
(20.0) Dia
.787
4
COM
(7.3)
.287
Snap-in • Single Pole
(9.7)
.382
5
1
(6.0)
.236
(11.1)
.437
(21.3)
.838
(5.5)
.217
6
L
–+
NO
3
2
Tactiles
L
–+
1
(21.3)
.838
(5.5)
.217
NC
3
2
NO
D
NO
Programmable Illuminated PB
Keylocks
Cap Colors Available:
Cap Color Available:
NO
Rotaries
Nonilluminated Caps
(3.7)
.146
(1.2) x (2.0) Typ
.047 x .079
1
(21.3)
.838
(5.5)
.217
Touch
Snap-in • Double Pole
(3.7)
.146
(1.2) x (2.0) Typ
.047 x .079
(0.5) Typ
.020
NO
3
LP0125CMKW015DB
D70
(2.5)
.098
(13.6) Dia
.535
(20.0) Dia
.787
(5.5)
.217
www.nkk.com
(7.3)
.287
(21.3)
.838
6
L
–+
2
(2.8) Typ
.110
NC
1
5
4
COM
(6.0)
.236
(11.1)
.437
NO
Supplement
COM
(3.0)
.118
(5.55)
.219
(7.3)
.287
Accessories
Indicators
LP0115CMKW015CB
(2.5)
.098
L
–+
2
(2.8) Typ
.110
(13.6) Dia
.535
(20.0) Dia
.787
NC
3
NO
(9.7)
.382
NO
Tilt
(0.5) Typ
.020
(9.7)
.382
Toggles
Series LP01
Short Body Pushbuttons
OPTIONAL ACCESSORIES
NO
– +
(17.0)
.669
(17.1)
.673
(17.0)
.669
AT719
Double Pole
Straight PC
Terminals
NC
NO
L
NO
– +
COM
(3.0)
.118
(17.0)
.669
(3.7)
.146
D
(5.0)
.197
(4.85) Typ
.191
(17.1)
.673
(3.7)
.146
(5.55)
.219
(4.85) Typ
.191
NC
NO
L
(4.0)
.157
(17.1)
.673
COM
(3.0) Typ
.118
(3.7)
.146
(5.55) Typ
.219
(17.0)
.669
(3.7) Typ
.146
(4.0)
.157
(4.85) Typ
.191
(4.85) Typ
.191
(5.55)
.219
CL
Material: Glass fiber reinforced polyamide
(5.55) Typ
.219
Note: Order adaptors separately
Tactiles
CL
(1.0) Dia Typ
.039
(1.85) Typ
.073
(3.0) Typ
.118
(1.0) Dia Typ
.039
(1.85) Typ
.073
(3.0) Typ
.118
NO
– +
(3.7) Typ
.146
NO
COM
(5.55) Typ
.219
(5.0)
.197
AT718
Single Pole
Straight PC
Terminals
L
(3.0) Typ
.118
(3.7)
.146
(5.55)
.219
NC
NO
– +
COM
(3.0)
.118
(4.85) Typ
.191
Pushbuttons
L
Programmable Illuminated PB
NC
NO
Keylocks
(4.85) Typ
.191
Rotaries
(17.1)
.673
AT717
Double Pole
Solder Lug/
Quick Connect
Terminals
Slides
AT716
Single Pole
Solder Lug/
Quick Connect
Terminals
Rockers
Adaptors
Switch Dimensions Shown with Adaptor AT716
Tilt
Dimension A: Solder Lug .197” (5.0mm); Straight PC .157” (4.0mm)
Panel thickness for LP01 Bushing Mount: .079” ~ .256” (2.0mm ~ 6.5mm)
A
Touch
(27.3)
1.075
LEGENDS
Indicators
NKK Switches can provide custom legends for caps. Contact factory for more information.
Recommended Methods:
R
PW
Accessories
Suggested Printable Area for LP01 Cap
Epoxy based ink is recommended.
(12.07) Dia
.475
(13.6) Dia
.535
(0.76) Typ
.030
Supplement
Pad Print or Laser Etch on cap.
Shaded area is printable area
www.nkk.com
D71
Similar pages