Download Specifications

Toggles
Series G3B
General Specifications
Rockers
Pushbuttons
Programmable Illuminated PB
Keylocks
Rotaries
Slides
Tactiles
Tilt
Touch
Indicators
Accessories
Supplement
Ultra-Miniature Process Sealed SMT Pushbuttons
Electrical Capacity (Resistive Load)
C
Logic Level: 0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Other Ratings
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Travel: Materials & Finishes
Actuator:
Case:
Sealing Rings:
Movable Contacts:
Stationary Contacts:
Base:
Terminals:
Environmental Data
Operating Temperature Range:
Humidity: Vibration:
Shock:
Installation
Mounting:
Coplanarity:
80 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
50,000 operations minimum
50,000 operations minimum
2.0N
Pretravel: .024” (0.6mm); Overtravel: .019” (0.5mm); Total Travel: .043” (1.1mm)
Polyphenylene sulfide (UL94V-0)
Polyphenylene sulfide (UL94V-0)
Nitrile butadiene rubber
Phosphor bronze with gold plating
Phosphor bronze with gold plating
Polyphenylene sulfide (UL94V-0)
Phosphor bronze with gold plating
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 500Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
It is recommended that the body of models for upright mounting without bracket be fastened to a
panel or similar support for protection of solder joints from mechanical stress.
See specifications in Terms & Acronyms in Supplement section.
Processing
Soldering: Reflow Soldering Recommended. See Profile B in Supplement section.
Manual Soldering: See Profile B in Supplement section.
Cleaning:
Automated cleaning. See Cleaning specifications in Supplement section.
Standards & Certifications
Flammability Standard:
C52
UL94V-0 actuator, case & base
The G3B Series pushbuttons have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
www.nkk.com
Toggles
Series G3B
Rockers
Distinctive Characteristics
Ultra-miniature size allows high density mounting, and extremely light weight
of 0.6 gram makes these switches ideal for handheld equipment.
C
Programmable Illuminated PB
Tape-reel and stick-tube packaging allow rapid automated
placement of surface mount devices. Tape-reel packaging
meets EIA-481-D Standard.
Pushbuttons
Ultra-Miniature Process Sealed SMT Pushbuttons
Keylocks
Heat resistant resin used for housing, base, and plunger
allows vapor phase and infrared convection reflow
soldering.
Slides
Rotaries
Combination of design features achieves total seal and
allows automated processing techniques, including flux
cleaning procedures: one-piece bushing and housing,
rubber seals surrounding actuator and base, epoxy at
joint of case and base, and molded-in, epoxy-sealed
terminals.
Tactiles
Award-winning STC contact mechanism with
benefits unavailable in conventional mechanisms:
smoother, positive detent actuation, increased contact
stability and unparalleled logic-level reliability. (Additional
STC details in Terms & Acronyms; see Supplement section.)
Tilt
Gull-wing terminals provide mechanical stability during soldering
and simplified solder joint inspection.
Touch
Coplanarity: all considered surfaces must lie between two parallel planes that
area maximum distance apart of .0059” (0.15mm). (Additional coplanarity
details in Terms and Acronyms in the Supplement section.)
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
C53
Series G3B
Toggles
Ultra-Miniature Process Sealed SMT Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
C
1
5
A
Poles
1
SPDT
2
DPDT
A
ON
Gull Wing for
Upright Mount
B
Gull Wing for
Upright with Bracket
H
Gull Wing for
Right Angle
.130” (3.3mm) Long
(ON)
Colors
P
Plunger
Circuits
5
B
Terminals
Black
B
White
C
Red
Slip-on Cap
.157” (4.0mm) Diameter
X
(For installation after
processing only)
Packaging
No Partitioned Tray for Upright &
Code Right Angle - Any Quantity
Rotaries
A
Optional Caps
( ) = Momentary
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
G3B
R
Tape-Reel for Right Angle Only
500 Pieces/Reel
S
Stick-Tube for Upright Mount
50 Pieces/Stick
Process Compatible Cap
.157” (4.0mm) Diameter
(Combines with R or S
packaging only)
Y
Slides
Packaging details at end of G3B Series
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Tactiles
G3B15AB
.130” (3.3mm)
Long Plunger
Gull Wing Terminals for
Upright with Bracket Mount
Tilt
Packaged in Partitioned Tray
POLES & CIRCUITS
Touch
Indicators
Accessories
Supplement
SPDT
ON-(ON) Circuit
Plunger Position
( ) = Momentary
Normal
Down
Connected Terminals
Normal
Throw & Schematics
Down
Note: Terminal numbers are not
actually on the switch.
Pole
Model
SP
G3B15
ON
(ON)
5-6
5-4
SPDT
DP
G3B25
ON
(ON)
5-6 2-3
5-4 2-1
DPDT
C54
5 (COM)
5
www.nkk.com
6
4
4
(COM)
6
1
2
3
Series G3B
Toggles
Ultra-Miniature Process Sealed SMT Pushbuttons
PLUNGER & OPTIONAL CAPS
(2.0) Dia
.079
(3.3)
.130
(4.0) Dia
.157
(3.8)
.150
(2.4)
.094
Finish: Glossy
Factory assembled. Available with tape-reel
or stick-tube packaging only.
Actual Size
Material: Polyamide
Caution: Pulling force specification for this
cap is not warranted after reflow processing.
Material: Polyamide
Finish: Glossy
A
Cap Colors Available:
B
Black
C
White
Red
TYPICAL SWITCH DIMENSIONS
Single & Double Pole
Support Legs
(8.5)
5 COM .335
6
(2.0) Dia
.079
(0.7)
.028
Slot
(1.5)
.059
(3.3)
.130
4
2
5
6
3
(0.1)
.004
(7.6)
.299
(7.6)
.299
Single & Double PoleUpright Mounting with Bracket
(0.25) Typ
.010
(4.0) Dia
.157
(3.8)
.150
Support Legs
1
4
(11.0)
5 COM .433
6
(2.0) Dia
.079
(0.7)
.028
Slot
(1.5)
.059
(3.3)
.130
(9.0)
.354
(0.5) Typ
.020
(0.9) Typ
.035
(0.1)
.004
4
2
5COM
6
3
(11.0)
.433
(0.5) Typ
.020
(0.9) Typ
.035
(7.6)
.299
(7.6)
.299
(1.2) Typ
.047
(3.8)
.150
(1.2) Typ
.047
(5.08)
.200
(5.0)
.197
G3B25AP
Tilt
(8.5)
.335
(0.5) Typ
.020
(0.5) Typ
.020
(9.0)
.354
COM
Rotaries
1
4
(5.08)
.200
(0.6) Typ
.024
Keylocks
(4.0) Dia
.157
(5.0)
.197
Upright Mounting
(0.25) Typ
.010
G3B15AB
(3.8) Typ
.150
Right Angle Mounting
Indicators
(2.54) Typ (1.25) Typ
.100
.049
(4.0) Dia
.157
(11.0)
.433
(2.0) Dia
.079
(0.5) Typ
.020
(0.9) Typ
.035
(0.55)
.022
Single Pole
Double Pole
(5.55)
.219
(5.55)
.219
(0.25) Typ
.010
(8.5)
.335
6
(0.25)
.010
5 4
COM
6 3 5 2 4 1
(0.1)
.004
www.nkk.com
Accessories
(9.0)
.354
COM
(0.1)
.004
Supplement
Slot
(1.5)
.059
(3.3)
.130
C
Tactiles
(0.6) Typ
.024
Rockers
Available with bulk packaging only. Cap must be
installed after processing.
Process Compatible Cap
.157” (4.0mm) Diameter
Pushbuttons
Y
Programmable Illuminated PB
AT4063 Slip-on Cap
.157” (4.0mm) Diameter
X
Slides
.130” (3.3mm)
Long Plunger
Touch
A
G3B15AH
C55
Toggles
Series G3B
(1.7) Typ
.067
(2.54) Typ
.100
Single Pole
Double Throw
(0.635)
.025
(0.7) Typ
.028
(1.7) Typ
.067
(2.54) Typ
.100
4
Rotaries
(0.635)
.025
(0.7) Typ
.028
6
Support
Pads
(6.0)
.236
(2.54) Typ
.100
1
2
(0.635) Typ
.025
(0.7) Typ
.028
(6.0)
.236
Partitioned Tray
for Upright & Right Angle
Slides
Any quantity
Touch
Tilt
Tactiles
If the G3 upright models are ordered in less than
50-piece increments or the right angle models in
less than 500-piece increments, the switches are
packaged in a partitioned tray.
No code is required.
R
Tape-Reel
for Right Angle
Indicators
500 pieces per reel
Accessories
Switches must be ordered in 500-piece increments
when tape-reel packaging is selected.
Supplement
This packaging meets EIA-481-D Standard for “16mm
and 24mm Embossed Carrier Taping of Surface Mount
Components for Automatic Handling.”
C56
(6.0)
.236
(3.8)
.150
www.nkk.com
(9.75)
.384
(1.55) Typ
.061
(1.1) Typ
.043
Right Angle Mounting
(1.1) Typ
.043
(9.75)
.384
2
3
6
(6.0)
.236
(9.75)
.384
(1.55) Typ
.061
(3.8)
.150
(1.7) Typ
.067
(2.54) Typ
.100
4
5
(0.635)
.025
(0.7) Typ
.028
(3.0)
.118
6
(1.55) Typ
.061
(1.1) Typ
.043
1
4
5
3
6
Support
Pads
(5.08)
.200
6
(1.7) Typ
.067
4
(1.1) Typ
.043
5
PACKAGING
No
Code
(3.8)
.150
4
(5.08)
.200
5
(0.635) Typ
.025
(0.7) Typ
.028
Upright Mounting with Bracket
(1.7) Typ
.067
(2.54) Typ
.100
5
C
Double Pole
Double Throw
Upright Mounting
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
Pad Layouts for
Surface Mount
Terminals
Ultra-Miniature Process Sealed SMT Pushbuttons
(9.75)
.384
(1.55) Typ
.061
(3.8)
.150
1
4
2
5
3
6
(1.7) Typ
.067
(1.27) Typ
.050
(0.635) Typ
.025
(0.7) Typ
.028
(3.0)
.118
Series G3B
Toggles
Ultra-Miniature Process Sealed SMT Pushbuttons
PACKAGING (CONTINUED)
50 pieces per stick
Switches must be ordered in 50-piece increments when
stick-tube packaging is selected.
Programmable Illuminated PB
C
Tape-Reel Packaging for Right Angle Mount
Keylocks
Each tape-reel of 550 pockets contains 500 switches.
Minimum Leader Length: 7.87” (200mm) Minimum Trailer Length: 1.97” (50mm)
Overall Dia (330.0)
13.0
(11.5)
.453
Part No.
(6.0)
.236
(17.8)
.701
(2.1) Dia Typ
.083
(2.0)
.079
Direction of Feed
Reel Dimensions
(13.9)
.547
(8.6)
.339
(1.5) R
.059
Terminal #1
(24.4)
.961
Rotaries
(0.4)
.016
Tape Dimensions
Tilt
(21.0) Dia
.827
(2.0)
.079
(24.0)
.945
(1.5) Dia Typ
.059
Slides
(78.49) Dia
3.090
(13.0) Dia
.512
(2.0) Typ
.079
(4.0) Typ
.157
(16.0) Typ
.630
Tactiles
(1.75)
.069
(2.0) Typ
.079
Pushbuttons
Rockers
Stick-Tube
for Upright Mount
S
Stick-Tube Packaging for Upright Mount
(7.7)
.303
Indicators
L = Length
Touch
Each stick-tube contains 50 switches.
G3B Upright (code P)
Accessories
(15.3)
.602
18.31” (465mm)
G3B Upright with Bracket (code B)
(9.8)
.386
L
Supplement
21.26” (540mm)
Stick-Tube Dimensions
www.nkk.com
C57
Similar pages