PL IA N T Features M ■ RoHS compliant* ■ Suitable for most types of soldering *R oH S CO ■ Power rating at 70 °C: CR2010 - 1/2 W, CR2512 - 1 W ■ Tight tolerances of bottom electrode width ■ Three layer termination process with nickel barrier prevents leaching and provides excellent solderability processes ■ Standard packaging on tape and reel ■ AEC-Q200 approval upon request CR2010/CR2512 - Chip Resistors Derating Curve Characteristic Power Rating @ 70 °C Operating Temperature Range Derated to 0 Load at Maximum Working Voltage Maximum Overload Voltage Resistance Range: 1 % E-96 + E-24 Model Model CR2010 CR2512 1/2 W 1W -55 °C to +155 °C +155 °C 200 V 400 V 100 Rated Power (%) Electrical Characteristics 80 60 40 20 0 -55 1M ohms < R ≤ 10M ohms ±200 PPM/°C 10 ohms ≤ R ≤ 10M ohms ±200 PPM/°C 1 ohm ≤ R < 10 ohms 10M ohms < R ≤ 20M ohms ±400 PPM/°C Resistance Range: 5 % E-24 Zero Ohm Jumper <0.05 ohm Rated/Maximum Current 2 A/5 A 0 70 155 Ambient Temperature (°C) 10 ohms ≤ R ≤ 1M ohms ±100 PPM/°C For Standard Values Used in Capacitors, Inductors, and Resistors, click here. Dimensional Drawing I1 I1 2 A/5 A H Chip Dimensions Dimension Model CR2010 5.00 ± 0.20 (0.197 ± 0.008) 2.50 ± 0.20 (0.098 ± 0.008) 0.60 ± 0.10 (0.024 ± 0.004) 0.60 ± 0.25 (0.024 ± 0.010) 0.60 ± 0.25 (0.024 ± 0.010) L W H I1 I2 Model CR2512 6.30 ± 0.20 (0.248 ± 0.008) 3.10 ± 0.20 (0.122 ± 0.008) 0.60 ± 0.15 (0.024 ± 0.006) 0.60 ± 0.25 (0.024 ± 0.010) 0.60 ± 0.25 (0.024 ± 0.010) I2 I2 W L DIMENSIONS: MM (INCHES) Performance Characteristics Test Thermal Shock Short Time Overload Resistance to Solder Heat Resistance to Dry Heat Load Life Load Life with Humidity Solderability Bending Dielectric Withstanding Voltage Insulation Resistance Procedure Method Test Limits ΔR 1% 5% IEC60115-1-4.19 ≤±(0.5 % + 0.05 Ω) ≤±(1 % + 0.05 Ω) IEC60115-1-4.13 IEC60115-1-4.18 IEC60115-1-4.23.2 ≤±(1 % + 0.05 Ω) ≤±(0.5 % + 0.05 Ω) ≤±(1 % + 0.05 Ω) ≤±(1 % + 0.05 Ω) ≤±(2 % + 0.1 Ω) -55 ℃ for 30 minutes, +155 ℃ for 30 minutes, 5 cycles 2.5 X rated voltage for 5 seconds 270 ±5 ℃ for 10 ±1 seconds 125 ±5 ℃ for 96 ±4 hours Rated voltage for 1000 hours, 70 ℃, 1.5 hours “ON“, 0.5 hours “OFF” Rated voltage for 1000 hours, 40 ±2 ℃, 90~95 % RH, 1.5 hours “ON“, 0.5 hours “OFF” 245 ±5 ℃, 2 ±0.5 seconds 3 mm IEC60115-1-4.17 IEC60115-1-4.33 ≥95 % of area covered ≤±(0.5 % + 0.05 Ω) ≤±(1 % + 0.05 Ω) -- IEC60115-1-4.7 >500 V 100 V IEC60115-1-4.6 ≥1 GΩ IEC60115-1-4.25.1 ≤±(1 % + 0.05 Ω) ≤±(3 % + 0.1 Ω) IEC60115-1-4.24 ≤±(1 % + 0.05 Ω) ≤±(3 % + 0.1 Ω) *RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. CR2010/CR2512 - Chip Resistors How to Order CR 2010 - F X - 8252 E LF Model (CR = Chip Resistor) Size • 2010 • 2512 Resistance Tolerance F = ±1 % .............. Use with “X” TCR code only for values from 10 ohms through 1 megohm; Use with “W” TCR code only for values from 1 megohm through 10 megohms J = ±5 % .................Use with “W” TCR code for values from 10 ohms through 10 megohms; Use with “Z” TCR code for values above 10 megohms through 20 megohms; Use with “/” TCR code for zero ohm (jumper) and values from 1 ohm through 9.1 ohms. TCR (ppm/°C) X = ±100 W = ±200 Z = ±400 / = Used with “J” Resistance Tolerance code for zero ohm (jumper) and values from 1 ohm through 9.1 ohms. Resistance Value For 1 % Tolerance: <100 ohms...............“R” represents decimal point (example: 24R3 = 24.3 ohms) ≥100 ohms...............First three digits are significant, fourth digit represents number of zeros to follow (example: 8252 = 82.5k W) For 5 % Tolerance: <10 ohms .............. “R” represents decimal point (example: 4R7 = 4.7 ohms) ≥10 ohms............... First two digits are significant, third digit represents number of zeros to follow (example: 474 = 470k ohms; 000 = Jumper) Packaging E = Embossed Plastic Tape (4,000 pcs.) on 7 ” Plastic Reel Termination LF = Tin-plated (RoHS compliant) Soldering Profile for RoHS Compliant Chip Resistors and Arrays Marking Explanation 275 <1> Maximum of 20 seconds between Resistors with 5 % tolerance may have a 3-digit or 4-digit resistance code. Complete information about resistance value and tolerance is found on the label of the reel of chip resistors. • 5 %: 3 digits, first two digits are significant, third digit is number of zeros to follow. Letter R is decimal point for values from 1 to 9.9 ohms. • 5 %: 4 digits, first three digits are significant, fourth digit is number of zeros to follow. Letter R is decimal point for values from 1 to 99.9 ohms. • 1 %: 4 digits, first three digits are significant, fourth digit is number of zeros to follow. Letter R is decimal for values from 1 to 99.9 ohms. 260 °C peak +255 °C and +260 °C <1> 255 °C 225 Temperature (°C) 220 °C 190 °C 175 60 - 90 seconds Ramp Down 6 °C/second 150 °C 125 60 - 120 seconds 10 seconds minimum 75 Ramp Up 3 °C/second maximum 25 0 50 100 150 Time (seconds) 200 250 300 Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. 3312 - 2 mm SMD CR2010/CR2512 - Chip Trimming Resistors Potentiometer Packaging Dimensions 4.0 ± 0.1 (.157 ± .004) Model CR2010 2.8 ± 0.2 (0.110 ± 0.008) 5.5 ± 0.2 (0.217 ± 0.008) 12.0 ± 0.3 (0.472 ± 0.012) 5.5 ± 0.05 (0.217 ± 0.002) 4.0 ± 0.1 (0.157 ± 0.004) Dimension 2.0 ± 0.05 (.079 ± .002) A B A F B W W P0 1.5 +0.1/-0 (.056 + .004/-0) 1.75 ± 0.1 (.059 ± .004) F P0 DIMENSIONS: Model CR2512 3.5 ± 0.2 (0.138 ± 0.008) 6.7 ± 0.2 (0.264 ± 0.008) 12.0 ± 0.3 (0.472 ± 0.012) 5.5 ± 0.05 (0.217 ± 0.002) 4.0 ± 0.1 (0.157 ± 0.004) MM (INCHES) 2.0 ± 0.5 (.080 ± .020) 13.0 ± 0.5 (.512 ± .020) 80.0 ± 0.5 (3.150 ± .020) 20.0 MIN. (.787) 178.0 ± 2.0 (7.008 ± .080) 16.7 MAX. (.657) REV. 07/15 Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications.

- Similar pages