Target displays
Plug-on mount, enter key, manual format alignment
Display LCD two lines, interface RS485
N 155
Features
–– Target display for manual format aligning
–– One key permanently assigned as target
–– Display: LCD backlit, two lines
–– Actual value and target display
–– Interface RS485
–– With or without LED status display
Technical data - mechanical design
Voltage supply
24 VDC ±10 %
Protection DIN EN 60529
IP 54
Current consumption
≤30 mA
Operating temperature
-10...+50 °C
Display
LCD, 7-segment display,
2-lines, backlit
Storage temperature
-20...+70 °C
Display range
-9999...+99999
Relative humidity
80 % non-condensing
LED operating status
Green: actual value = set value
accepted
Red: actual value ≠ set value
Connection
Interface
RS485 (ASCII protocol)
Data memory
>10 years in EEPROM
Programmable
parameters
Measuring unit mm/inch
Direction arrows
Decimal point
- Male/female connector M8,
4-pin
- Cable output (30/15 cm) with
male/female connector M8,
4-pin
- Cable output (30/15 cm) with
male/female connector M16,
5-pin
Operation / keypad
Standard
DIN EN 61010‑1
Overvoltage category II
Protection class II
Pollution degree 2
Membrane with one softkey
(handshake)
Housing type
Surface mount housing with
mounting plate
Emitted interference
DIN EN 61000-6-3
Dimensions
37 x 75 x 29 mm
Interference immunity
DIN EN 61000-6-2
Mounting
Mount onto plate
Approval
UL approval / E63076
Weight approx.
60 g
Material
Polyamide black, UL 94V-0
1
www.baumer.com/motion
24/5/2016
Technical data - electrical ratings
Subject to modification in technic and design. Errors and omissions excepted.
N 155 with connector output
Target displays
Plug-on mount, enter key, manual format alignment
Display LCD two lines, interface RS485
N 155
Part number
N 155.
1
Description
3
The multicon spindle positioning system is completed by a
target display indicating also positions of hand wheels,
limits, linear units etc in close vicinity of the actuator. The
backlit LCD display provides the editing engineer with the
target parameters. A LED state indicator (red/green) that is
optionally available enables comfortable visualization of the
current alignment status even from remote.
The handshake key is saving the edited parameters. Serial
interface RS485 enables network of maximum 32 target and
spindle position displays with PC or PLC.
For complete solutions also memory controllers as decentralized operating and memory terminals are available.
X01
Display
B Horizontal at front
C Horizontal at front with LED
status
Voltage supply
3 24 VDC
Connection
0 Connector output M8 with male and
female connector
1 Bottom cable output M8
2 Rear cable output M8
3 Bottom cable output M16
Interface
1 RS485
Accessories
Adaptor cable between cable connector M8
and female M16, 1 m
Z 178.AW1
Cable connector M8, 4-pin, without cable with
integrated terminating resistor 120 Ω
Z 178.B01
Female connector M8, 4-pin, without cable
Z 178.D05
Data and supply cable M8, Master to N 150
and N 155, 5 m
Z 178.S01
Cable connector M8, 4-pin, without cable
Z 178.V01
Coupling cable with M8 - M8, 1 m cable
Z 178.050
Data and supply cable, ø5 mm,
4 cores, shielded, on 50 m drum
2
www.baumer.com/motion
24/5/2016
Z 178.A01
Subject to modification in technic and design. Errors and omissions excepted.
Connectors and cables
Target displays
Plug-on mount, enter key, manual format alignment
Display LCD two lines, interface RS485
N 155
Terminal assignment
M8 connector
M16 connector Assignment
Pin 1
Pin 5
Tx/Rx-, RS485
Pin 2
Pin 4
Tx/Rx+, RS485
Pin 3
Pin 1
Sensor supply +24 V
Pin 4
Pin 2
Sensor supply 0 V
M8 connector
2
2
4
4
1
3
M16 connector
5
3
2
1
2
3
4
1
5
Subject to modification in technic and design. Errors and omissions excepted.
4
M16 female
connector
3
www.baumer.com/motion
24/5/2016
1
3
M8 female
connector
Target displays
Plug-on mount, enter key, manual format alignment
Display LCD two lines, interface RS485
N 155
Dimensions
Connector male and female
Cable output rear, M8
3*JODQGZLWK
FRQQHFWRU
3*JODQGZLWKIHPDOH
FRQQHFWRU
6WDWXV
/('
&XWRXWIRUUHDUFDEOH
RXWSXW
&RQQHFWRU )HPDOH
FRQQHFWRU
5
±
0
±
10
10
Bottom cable output, M8 and M16
300
150
Female
connector
M8
300
150
16
Female
connector
M1 6
Connector
M8
Connector
M1 6
4
www.baumer.com/motion
24/5/2016
Subject to modification in technic and design. Errors and omissions excepted.
14