DATASHEET

HFA1100
®
Data Sheet
October 26, 2004
850MHz, Low Distortion Current Feedback
Operational Amplifiers
Features
• Low Distortion (30MHz, HD2) . . . . . . . . . . . . . . . . -56dBc
The HFA1100 is a high-speed, wideband, fast settling
current feedback amplifier built with Intersil's proprietary
complementary bipolar UHF-1 process. It operates with
single supply voltages as low as 4.5V (see Application
Information section).
• -3dB Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . 850MHz
• Very Fast Slew Rate . . . . . . . . . . . . . . . . . . . . . 2300V/µs
• Fast Settling Time (0.1%). . . . . . . . . . . . . . . . . . . . . 11ns
• Excellent Gain Flatness
- (100MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.14dB
- (50MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.04dB
The HFA1100 is a basic op amp with uncommitted pins 1, 5,
and 8.
This device offers a significant performance improvement
over the AD811, AD9617/18, the CLC400-409, and the
EL2070, EL2073, EL2030.
• High Output Current . . . . . . . . . . . . . . . . . . . . . . . . . 60mA
• Overdrive Recovery . . . . . . . . . . . . . . . . . . . . . . . . <10ns
• Operates with 5V Single Supply (See AN9745)
Ordering Information
PART NUMBER
(BRAND)
TEMP.
RANGE (°C)
• Pb-Free Available (RoHS Compliant)
PACKAGE
PKG.
DWG. #
HFA1100IP
-40 to 85
8 Ld PDIP
E8.3
HFA1100IB
(H1100I)
-40 to 85
8 Ld SOIC
M8.15
HFA1100IB96
(H1100I)
-40 to 85
8 Ld SOIC
Tape and Reel
M8.15
HFA1100IBZ (Note)
(H1100I)
-40 to 85
8 Ld SOIC (Pb-free) M8.15
HFA1100IBZ96 (Note)
(H1100I)
-40 to 85
8 Ld SOIC
Tape and Reel
(Pb-free)
HFA11XXEVAL
FN2945.9
Applications
• Video Switching and Routing
• Pulse and Video Amplifiers
• RF/IF Signal Processing
• Flash A/D Driver
• Medical Imaging Systems
• Related Literature
- AN9420, Current Feedback Theory
- AN9202, HFA11XX Evaluation Fixture
- AN9745, Single 5V Supply Operation
M8.15
DIP Evaluation Board for High-Speed Op
Amps
Pinout
NOTE: Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with
both SnPb and Pb-free soldering operations. Intersil Pb-free products
are MSL classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J STD-020C.
HFA1100 (PDIP, SOIC)
TOP VIEW
The Op Amps with Fastest Edges
NC
1
-IN
2
+IN
3
V- 4
8
NC
-
7
V+
+
6
OUT
5
NC
INPUT
220MHz
SIGNAL
OUTPUT
(AV = 2)
HFA1100
OP AMP
0ns
25ns
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2000, 2004. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
HFA1100
Absolute Maximum Ratings TA = 25°C
Thermal Information
Voltage Between V+ and V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSUPPLY
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V
Output Current (50% Duty Cycle) . . . . . . . . . . . . . . . . . . . . . . 60mA
Thermal Resistance (Typical, Note 1)
θJA (°C/W)
θJC (°C/W)
PDIP Package . . . . . . . . . . . . . . . . . . .
130
N/A
SOIC Package . . . . . . . . . . . . . . . . . . .
170
N/A
Maximum Junction Temperature (Plastic Package) . . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
Operating Conditions
Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
VSUPPLY = ±5V, AV = +1, RF = 510Ω , RL = 100Ω , Unless Otherwise Specified
Electrical Specifications
(NOTE 2)
TEST
LEVEL
TEMP.
(°C)
MIN
TYP
MAX
UNITS
A
25
-
2
6
mV
A
Full
-
-
10
mV
C
Full
-
10
-
µV/°C
A
25
40
46
-
dB
A
Full
38
-
-
dB
A
25
45
50
-
dB
A
Full
42
-
-
dB
A
25
-
25
40
µA
A
Full
-
-
65
µA
C
Full
-
40
-
nA/°C
A
25
-
20
40
µA/V
A
Full
-
-
50
µA/V
A
25
-
12
50
µA
A
Full
-
-
60
µA
C
Full
-
40
-
nA/°C
A
25
-
1
7
µA/V
A
Full
-
-
10
µA/V
A
25
-
6
15
µA/V
A
Full
-
-
27
µA/V
Non-Inverting Input Resistance
A
25
25
50
-
kΩ
Inverting Input Resistance
C
25
-
20
30
Ω
Input Capacitance (Either Input)
B
25
-
2
-
pF
Input Common Mode Range
C
Full
±2.5
±3.0
-
V
TEST
CONDITIONS
PARAMETER
INPUT CHARACTERISTICS
Input Offset Voltage (Note 3)
Input Offset Voltage Drift
∆VCM = ±2V
VIO CMRR
∆VS = ±1.25V
VIO PSRR
Non-Inverting Input Bias Current
(Note 3)
+IN = 0V
+IBIAS Drift
∆VCM = ±2V
+IBIAS CMS
Inverting Input Bias Current (Note 3)
-IN = 0V
-IBIAS Drift
∆VCM = ±2V
-IBIAS CMS
∆VS = ±1.25V
-IBIAS PSS
Input Noise Voltage (Note 3)
100kHz
B
25
-
4
-
nV/√Hz
+Input Noise Current (Note 3)
100kHz
B
25
-
18
-
pA/√Hz
-Input Noise Current (Note 3)
100kHz
B
25
-
21
-
pA/√Hz
25
-
300
-
kΩ
TRANSFER CHARACTERISTICS
AV = +2, Unless Otherwise Specified
Open Loop Transimpedance (Note 3)
2
B
FN2945.9
HFA1100
VSUPPLY = ±5V, AV = +1, RF = 510Ω , RL = 100Ω , Unless Otherwise Specified (Continued)
Electrical Specifications
TEST
CONDITIONS
PARAMETER
(NOTE 2)
TEST
LEVEL
TEMP.
(°C)
MIN
TYP
MAX
UNITS
-3dB Bandwidth (Note 3)
VOUT = 0.2VP-P,
AV = +1
B
25
530
850
-
MHz
-3dB Bandwidth
VOUT = 0.2VP-P,
AV = +2, RF = 360Ω
B
25
-
670
-
MHz
Full Power Bandwidth
VOUT = 4VP-P,
AV = -1
B
25
-
300
-
MHz
Gain Flatness (Note 3)
To 100MHz
B
25
-
±0.14
-
dB
Gain Flatness
To 50MHz
B
25
-
±0.04
-
dB
Gain Flatness
To 30MHz
B
25
-
±0.01
-
dB
Linear Phase Deviation (Note 3)
DC to 100MHz
B
25
-
0.6
-
Degrees
Differential Gain
NTSC, RL = 75Ω
B
25
-
0.03
-
%
Differential Phase
NTSC, RL = 75Ω
B
25
-
0.05
-
Degrees
A
Full
1
-
-
V/V
A
25
±3.0
±3.3
-
V
A
Full
±2.5
±3.0
-
V
A
25, 85
50
60
-
mA
A
-40
35
50
-
mA
B
25
-
0.07
-
Ω
Minimum Stable Gain
OUTPUT CHARACTERISTICS
AV = +2, Unless Otherwise Specified
Output Voltage (Note 3)
AV = -1
Output Current
RL = 50Ω, AV = -1
DC Closed Loop Output Impedance
(Note 3)
2nd Harmonic Distortion (Note 3)
30MHz, VOUT = 2VP-P
B
25
-
-56
-
dBc
3rd Harmonic Distortion (Note 3)
30MHz, VOUT = 2VP-P
B
25
-
-80
-
dBc
3rd Order Intercept (Note 3)
100MHz
B
25
20
30
-
dBm
1dB Compression
100MHz
B
25
15
20
-
dBm
TRANSIENT RESPONSE AV = +2, Unless Otherwise Specified
Rise Time
VOUT = 2.0V Step
B
25
-
900
-
ps
Overshoot (Note 3)
VOUT = 2.0V Step
B
25
-
10
-
%
Slew Rate
AV = +1, VOUT = 5VP-P
B
25
-
1400
-
V/µs
Slew Rate
AV = +2, VOUT = 5VP-P
B
25
1850
2300
-
V/µs
0.1% Settling (Note 3)
VOUT = 2V to 0V
B
25
-
11
-
ns
0.2% Settling (Note 3)
VOUT = 2V to 0V
B
25
-
7
-
ns
Overdrive Recovery Time
2X Overdrive
B
25
-
7.5
10
ns
Supply Voltage Range
B
Full
±4.5
-
±5.5
V
Supply Current (Note 3)
A
25
-
21
26
mA
A
Full
-
-
33
mA
POWER SUPPLY CHARACTERISTICS
NOTES:
2. Test Level: A. Production Tested; B. Typical or Guaranteed Limit Based on Characterization; C. Design Typical for Information Only.
3. See Typical Performance Curves for more information.
3
FN2945.9
HFA1100
Application Information
Use of Die in Hybrid Applications
Optimum Feedback Resistor (RF)
The enclosed plots of inverting and non-inverting frequency
response detail the performance of the HFA1100 in various
gains. Although the bandwidth dependency on ACL isn’t as
severe as that of a voltage feedback amplifier, there is an
appreciable decrease in bandwidth at higher gains. This
decrease can be minimized by taking advantage of the
current feedback amplifier’s unique relationship between
bandwidth and RF . All current feedback amplifiers require a
feedback resistor, even for unity gain applications, and the
RF , in conjunction with the internal compensation capacitor,
sets the dominant pole of the frequency response. Thus, the
amplifier’s bandwidth is inversely proportional to RF . The
HFA1100 design is optimized for a 510Ω RF , at a gain of +1.
Decreasing RF in a unity gain application decreases stability,
resulting in excessive peaking and overshoot (Note:
Capacitive feedback causes the same problems due to the
feedback impedance decrease at higher frequencies). At
higher gains the amplifier is more stable, so RF can be
decreased in a trade-off of stability for bandwidth. The table
below lists recommended RF values for various gains, and the
expected bandwidth.
ACL
RF (Ω)
BW (MHz)
+1
510
850
-1
430
580
+2
360
670
+5
150
520
+10
180
240
+19
270
125
5V Single Supply Operation
This amplifier operates at single supply voltages down to
4.5V. The table below details the amplifier’s performance
with a single 5V supply. The dramatic supply current
reduction at this operating condition (refer also to Figure 23)
makes these op amps even better choices for low power 5V
systems. Refer to Application Note AN9745 for further
information.
PARAMETER
This amplifier is designed with compensation to negate the
package parasitics that typically lead to instabilities. As a
result, the use of die in hybrid applications results in
overcompensated performance due to lower parasitic
capacitances. Reducing RF below the recommended values
for packaged units will solve the problem. For AV = +2 the
recommended starting point is 300Ω, while unity gain
applications should try 400Ω.
PC Board Layout
The frequency performance of this amplifier depends a great
deal on the amount of care taken in designing the PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended,
while a solid ground plane is a must!
Attention should be given to decoupling the power supplies.
A large value (10µF) tantalum in parallel with a small value
chip (0.1µF) capacitor works well in most cases.
Terminated microstrip signal lines are recommended at the
input and output of the device. Output capacitance, such as
that resulting from an improperly terminated transmission
line will degrade the frequency response of the amplifier and
may cause oscillations. In most cases, the oscillation can be
avoided by placing a resistor in series with the output.
Care must also be taken to minimize the capacitance to ground
seen by the amplifier’s inverting input. The larger this
capacitance, the worse the gain peaking, resulting in pulse
overshoot and possible instability. To this end, it is
recommended that the ground plane be removed under traces
connected to pin 2, and connections to pin 2 should be kept as
short as possible.
An example of a good high frequency layout is the
Evaluation Board shown below.
Evaluation Board
An evaluation board is available for the HFA1100 (Part
Number HFA11XXEVAL). Please contact your local sales
office for information.
TYP
Input Common Mode Range
1V to 4V
-3dB BW (AV = +2)
267MHz
Gain Flatness (to 50MHz, AV = +2)
0.05dB
Output Voltage (AV = -1)
1.3V to 3.8V
Slew Rate (AV = +2)
475V/µs
0.1% Settling Time
17ns
Supply Current
5.5mA
4
FN2945.9
HFA1100
The layout and schematic of the board are shown below:
500Ω
500Ω
50Ω
VH
1
8
2
7
0.1µF
10µF
+5V
50Ω
IN
10µF
3
6
4
5
OUT
VL
0.1µF
GND
GND
-5V
TOP LAYOUT
BOTTOM LAYOUT
VH
1
+IN
VL
OUT
V+
VGND
Typical Performance Curves
AV = +2
1.2
90
AV = +2
0.9
OUTPUT VOLTAGE (V)
60
30
0
-30
-60
0.6
0.3
0
-0.3
-0.6
-90
-0.9
-120
-1.2
TIME (5ns/DIV.)
TIME (5ns/DIV.)
NORMALIZED GAIN (dB)
FIGURE 2. LARGE SIGNAL PULSE
VOUT = 200mVP-P
0
GAIN
-3
AV = +1
-6
AV = +2
-9
AV = +6
AV = +11
-12
PHASE
0
AV = +1
AV = +2
-180
AV = +6
-270
AV = +11
0.3
1
-90
10
100
FREQUENCY (MHz)
-360
1K
FIGURE 3. NON-INVERTING FREQUENCY RESPONSE
5
VOUT = 200mVP-P
0
GAIN
-3
AV = -1
-6
AV = -5
AV = -10
-9
AV = -20
-12
PHASE (DEGREES)
NORMALIZED GAIN (dB)
FIGURE 1. SMALL SIGNAL PULSE
PHASE
180
AV = -1
90
AV = -5
0
AV = -10
AV = -20
0.3
1
10
100
FREQUENCY (MHz)
-90
-180
1K
PHASE (DEGREES)
OUTPUT VOLTAGE (mV)
120
VSUPPLY = ±5V, RF = 510Ω , TA = 25°C, RL = 100Ω, Unless Otherwise Specified
FIGURE 4. INVERTING FREQUENCY RESPONSE
FN2945.9
HFA1100
RL = 1kΩ
3
GAIN
0
-3
-6
RL = 50Ω
RL = 100Ω
PHASE
0
-90
RL = 1kΩ
-180
RL = 100Ω
-270
RL = 1kΩ
0.3
1
10
100
FREQUENCY (MHz)
1K
-360
PHASE (DEGREES)
RL = 100Ω
RL = 50Ω
GAIN (dB)
10
0
0.160VP-P
0.500VP-P
0.920VP-P
1.63VP-P
-20
-30
0.3
1
10
100
FREQUENCY (MHz)
RL = 100Ω
RL = 50Ω
-6
PHASE
0
-90
RL = 1kΩ
-180
-270
1
-360
10
100
FREQUENCY (MHz)
1K
FIGURE 6. FREQUENCY RESPONSE FOR VARIOUS LOAD
RESISTORS
20
AV = +2
10
0
0.32VP-P
-10
1.00VP-P
-20
1.84VP-P
-30
0.3
3.26VP-P
1
10
100
FREQUENCY (MHz)
1K
FIGURE 8. FREQUENCY RESPONSE FOR VARIOUS
OUTPUT VOLTAGES
AV = +1
AV = +6
10
950
0
-10
BANDWIDTH (MHz)
NORMALIZED GAIN (dB)
-3
RL = 100Ω
RL = 1kΩ
1K
FIGURE 7. FREQUENCY RESPONSE FOR VARIOUS
OUTPUT VOLTAGES
20
GAIN
0
RL = 50Ω
RL = 100Ω
NORMALIZED GAIN (dB)
AV = +1
-10
RL = 1kΩ
3
0.3
FIGURE 5. FREQUENCY RESPONSE FOR VARIOUS LOAD
RESISTORS
20
AV = +2, VOUT = 200mVP-P
PHASE (DEGREES)
AV = +1, VOUT = 200mVP-P
6
GAIN (dB)
VSUPPLY = ±5V, RF = 510Ω , TA = 25°C, RL = 100Ω, Unless Otherwise Specified (Continued)
NORMALIZED GAIN (dB)
Typical Performance Curves
0.96VP-P
TO
3.89VP-P
-20
-30
900
850
800
750
700
0.3
1
10
100
FREQUENCY (MHz)
FIGURE 9. FREQUENCY RESPONSE FOR VARIOUS
OUTPUT VOLTAGES
6
1K
-50
-25
0
25
50
75
100
125
TEMPERATURE (oC)
FIGURE 10. -3dB BANDWIDTH vs TEMPERATURE
FN2945.9
HFA1100
Typical Performance Curves
VSUPPLY = ±5V, RF = 510Ω , TA = 25°C, RL = 100Ω, Unless Otherwise Specified (Continued)
25
0
2.5
180
135
PHASE
0.25
90
45
0
0.01
0.1
1
10
FREQUENCY (MHz)
100
GAIN (dB)
GAIN
PHASE (DEGREES)
GAIN (kΩ)
AV = +2
AV = -1
250
-0.05
-0.10
-0.15
-0.20
500
1
10
FREQUENCY (MHz)
FIGURE 11. OPEN LOOP TRANSIMPEDANCE
FIGURE 12. GAIN FLATNESS
AV = +2, VOUT = 2V
AV = +2
2.0
0.6
SETTLING ERROR (%)
1.5
DEVIATION (DEGREES)
100
1.0
0.5
0
-0.5
-1.0
-1.5
0.4
0.2
0
-0.2
-0.4
-0.6
-2.0
0
15
30
45
60
75
90 105 120
FREQUENCY (MHz)
135
150
-4
FIGURE 13. DEVIATION FROM LINEAR PHASE
1
6
11
16
21
26
TIME (ns)
31
36
41
46
FIGURE 14. SETTLING RESPONSE
40
2-TONE
35
INTERCEPT POINT (dBm)
OUTPUT RESISTANCE (Ω)
1000
100
10
1
30
25
20
15
10
5
0.1
0
0
0.3
1
10
100
FREQUENCY (MHz)
1000
FIGURE 15. CLOSED LOOP OUTPUT RESISTANCE
7
100
200
300
FREQUENCY (MHz)
400
FIGURE 16. 3rd ORDER INTERMODULATION INTERCEPT
FN2945.9
HFA1100
VSUPPLY = ±5V, RF = 510Ω , TA = 25°C, RL = 100Ω, Unless Otherwise Specified (Continued)
-30
-30
-35
-40
-40
DISTORTION (dBc)
DISTORTION (dBc)
Typical Performance Curves
100MHz
-45
50MHz
-50
-55
-60
-50
100MHz
-60
-70
-90
30MHz
-110
-70
-5
-3
-1
1
3
5
7
9
OUTPUT POWER (dBm)
11
13
-5
15
-3
-1
3
5
7
9
11
13
15
FIGURE 18. 3rd HARMONIC DISTORTION vs POUT
35
RF = 360Ω
VOUT = 2VP-P
AV = +1
30
AV = +2
OVERSHOOT (%)
VOUT = 1VP-P
VOUT = 0.5VP-P
VOUT = 2VP-P
25
RF = 360Ω
VOUT = 1VP-P
RF = 360Ω
20 VOUT = 0.5VP-P
15
10
5
RF = 510Ω
VOUT = 2VP-P
RF = 510Ω
VOUT = 1VP-P
RF = 510Ω
VOUT = 0.5VP-P
0
100
200
300
400
500
600
700
800
100
900 1000
200
300
FIGURE 19. OVERSHOOT vs INPUT RISE TIME
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
400
500
600
700
800
900 1000
INPUT RISE TIME (ps)
INPUT RISE TIME (ps)
FIGURE 20. OVERSHOOT vs INPUT RISE TIME
25
AV = +2, tR = 200ps, VOUT = 2VP-P
24
SUPPLY CURRENT (mA)
OVERSHOOT (%)
1
OUTPUT POWER (dBm)
FIGURE 17. 2nd HARMONIC DISTORTION vs POUT
OVERSHOOT (%)
30MHz
-100
-65
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
50MHz
-80
23
22
21
20
19
18
360
400
440
480
560
600
520
FEEDBACK RESISTOR (Ω)
640
680
FIGURE 21. OVERSHOOT vs FEEDBACK RESISTOR
8
-60
-40
-20
0
20
40
60
80
100 120
TEMPERATURE (oC)
FIGURE 22. SUPPLY CURRENT vs TEMPERATURE
FN2945.9
HFA1100
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
5
6
7
8
9
2.8
2.7
2.6
2.5
2.4
2.3
2.2
2.1
2
1.9
1.8
1.7
1.6
1.5
1.4
1.3
+IBIAS
VIO
-IBIAS
-60
10
45
42
39
36
33
30
27
24
21
18
15
12
9
6
3
0
-40
-20
0
20
40
60
80
BIAS CURRENTS (µA)
VSUPPLY = ±5V, RF = 510Ω , TA = 25°C, RL = 100Ω, Unless Otherwise Specified (Continued)
INPUT OFFSET VOLTAGE (mV)
SUPPLY CURRENT (mA)
Typical Performance Curves
100 120
TEMPERATURE (oC)
TOTAL SUPPLY VOLTAGE (V+ - V-, V)
FIGURE 23. SUPPLY CURRENT vs SUPPLY VOLTAGE
FIGURE 24. VIO AND BIAS CURRENTS vs TEMPERATURE
3.7
+VOUT
3.3
3.2
| - VOUT |
3.1
3
2.9
2.8
2.7
250
25
225
200
20
175
150
15
125
100
10
75
5
Eeni
NI
IiniNI Iini+
NI+
2.6
2.5
-60
-40
-20
0
20
40
60
80
100
120
TEMPERATURE (oC)
FIGURE 25. OUTPUT VOLTAGE vs TEMPERATURE
9
0
100
1K
10K
CURRENT NOISE (pA/√Hz)
275
3.5
3.4
300
30
AV = -1, RL = 50Ω
VOLTAGE NOISE (nV/√Hz)
OUTPUT VOLTAGE (V)
3.6
50
25
0
100K
FREQUENCY (Hz)
FIGURE 26. INPUT NOISE vs FREQUENCY
FN2945.9
HFA1100
Die Characteristics
DIE DIMENSIONS:
PASSIVATION:
63 mils x 44 mils x 19 mils
1600µm x 1130µm
Type: Nitride
Thickness: 4kÅ ±0.5kÅ
METALLIZATION:
TRANSISTOR COUNT:
Type: Metal 1: AlCu (2%)/TiW
Thickness: Metal 1: 8kÅ ±0.4kÅ
Type: Metal 2: AlCu (2%)
Thickness: Metal 2: 16kÅ ±0.8kÅ
52
SUBSTRATE POTENTIAL (POWERED UP):
Floating (Recommend Connection to V-)
Metallization Mask Layout
HFA1100
+IN
-IN
V-
BAL
VL
VH
BAL
V+
OUT
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
10
FN2945.9
Similar pages