CCPD-922 Model 9×14 mm SMD, 3.3V, LVPECL Frequency Range: Frequency Pulling: Temperature Range: (Option X) Storage: Input Voltage: Input Current: Output: Symmetry: Rise/Fall Time: Linearity: Logic: Disable Time: Start-up Time: Phase Jitter: 12 kHz to 20 MHz Phase Noise @ 100 MHz: 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz 1 MHz 10 MHz Aging: Ultra-Low Noise LVPECL CLOCK with -162 dBc/Hz Noise Floor! 40 MHz to 125 MHz ±20ppm APR Min 0°C to 70°C -40°C to 85°C -45°C to 90°C 3.3V ±0.3V 88mA Max Differential LVPECL 45/55% Max @ zero crossing point 1ns Max (20% to 80%) ±10% Max Terminated to Vcc-2V into 50 ohms "0" = Vcc-1.85V Min, Vcc-1.62V Max "1" = Vcc-1.02V Min, Vcc-0.81V Max 200ns 1ms Typical, 2ms Max 80 femtoseconds Typical @ 100 MHz The CCPD-922 represents our lowest -85 dBc/Hz Typical phase noise LVPECL CLOCK family. -115 dBc/Hz Typical Close-in phase noise has been reduced -145 dBc/Hz Typical -155 dBc/Hz Typical to -85 dBc/Hz @ 10 Hz offset while the -160 dBc/Hz Typical noise floor is at -162 dBc/Hz which leads -162 dBc/Hz Typical the industry for an LVPECL CLOCK. -162 dBc/Hz Typical <3ppm 1st year, <1ppm every year thereafter 100.000 MHz Specifications subject to change without notice. C CRYSTEK CORPORATION Rev: A Date: 02-Jun-2016 Page 1 of 2 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CCPD-922 Model 9×14 mm SMD, 3.3V, LVPECL Ultra-Low Noise LVPECL CLOCK with -162 dBc/Hz Noise Floor! 0.560 (14.2) Crystek Part Number Guide 0.360 (9.14) CCPD-922 X - 25 - 100.000 #1 #2 #3 #4 #5 #1 Crystek 9×14 SMD PECL OSC #2 Model 922 #3 Temp. Range: Blank = 0/70°C, X = -40/85°C #4 Stability: (see Table 1) #5 Frequency in MHz: 3 or 6 decimal places 0.100 (2.54) CRYSTEK CCPD-922 Frequency Date Code 0.040 (1.01) 1 6 2 5 3 0.070 (1.77) 4 0.200 (5.08) 0.560 (14.2) Example: CCPD-922X-100.000 = 3.3V, 45/55, -40/85°C, 100.000 MHz SUGGESTED PAD LAYOUT 0.210 (5.3) via to ground Stability Indicator 0.050 (1.27) 0.01µF 20 = ±20ppm 25 = ±25ppm Table 1 Enable/Disable Function Pin 2 Output Pin Open "0" level Vcc-1.620V Max "1" level Vcc-1.025V Min Active Disabled Active RECOMMENDED REFLOW SOLDERING PROFILE 900034 (See App Note listed on website) http://www.crystek.com/specification/reflow/900034.pdf C PIN Function 1 2 3 4 5 6 NC E/D GND OUT COUT Vdd 0.200 (5.08) 0.090 (2.28) Enable/Disable Pin 2 Input Output Pin Open "1" level 2.0V Min "0" level 0.8V Max Active Active High Z Mechanical: Shock: Solderability: Vibration: Solvent Resistance: Resistance to Soldering Heat: MIL-STD-883, Method 2002, Condition B MIL-STD-883, Method 2003 MIL-STD-883, Method 2007, Condition A MIL-STD-202, Method 215 MIL-STD-202, Method 210, Condition I or J Environmental: Thermal Shock: Moisture Resistance: MIL-STD-883, Method 1011, Condition A MIL-STD-883, Method 1004 Packaging: Tape/Reel: 100ea, 250ea, 500ea 24mm Tape CRYSTEK CORPORATION 0.280 (7.11) Rev: A Date: 02-Jun-2016 Page 2 of 2 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com