Texas Instruments Revision detection unimplemented OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2011.09-00000-g518a597 (Apr 12 2012 - 15:05:23) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled Found a daughter card connected NAND: HW ECC Hamming Code selected 256 MiB MMC: OMAP SD/MMC: 0 *** Warning - bad CRC, using default environment Net: cpsw Hit any key to stop autoboot: SD/MMC found on device 0 reading uEnv.txt 3 00 00 00 08 08 08 2 00 00 00 08 08 08 1 00 00 00 08 08 08 0 217 bytes read Loaded environment from uEnv.txt Importing environment from mmc ... Running uenvcmd ... reading uImage 3574496 bytes read ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux-3.2.0-gb02ab39 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3574432 Bytes = 3.4 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0-gb02ab39 (x0179557@psplinux052) (gcc version 4.4.3 (GCC) ) #1 Thu Apr 12 14:01:52 IST 2012 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: am335xevm [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyO0,115200n8 androidboot.console=ttyO0 mem=256M root=/ dev/mmcblk0p2 rw rootfstype=ext4 rootwait init=/init ip=off [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 256MB = 256MB total [ 0.000000] Memory: 251520k/251520k available, 10624k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0660000 (6496 kB) [ 0.000000] .init : 0xc0660000 - 0xc069b000 ( 236 kB) [ 0.000000] .data : 0xc069c000 - 0xc06f40e0 ( 353 kB) [ 0.000000] .bss : 0xc06f4104 - 0xc0823888 (1214 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ 0.000000] 0.000152] 0.058929] 0.059082] 0.059143] 0.059509] 0.079528] 0.095764] 0.096557] 0.096771] 0.097869] 0.098907] 0.100189] 0.100708] 0.100799] 0.100952] 0.100982] 0.100982] 0.109680] 0.110656] 0.111480] 0.111602] 0.111724] 0.111846] 0.111999] 0.128997] 0.130249] 0.132415] 0.133789] 0.135986] 0.138214] 0.139129] 0.140441] 0.141754] 0.143096] 0.144409] 0.145751] 0.147064] 0.148406] 0.149719] 0.150024] 0.150390] 0.150970] 0.151031] 0.151031] 0.151062] 0.151062] 0.151123] 0.151306] 0.158935] 0.159210] 0.159820] 0.160095] 0.160339] 0.160400] 0.160552] 0.160583] 0.160583] 0.160614] 0.160614] 0.161102] 0.161132] 0.161590] 0.161956] 0.162170] 0.162536] 0.162689] 0.162780] 0.162780] 0.162811] 0.162841] 0.163024] 0.163299] 0.163330] Console: colour dummy device 80x30 Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok omap_hwmod: gfx: failed to hardreset omap_hwmod: pruss: failed to hardreset print_constraints: dummy: NET: Registered protocol family 16 OMAP GPIO hardware version 0.1 omap_mux_init: Add partition: #1: core, flags: 0 omap_i2c.1: alias fck already exists omap2_mcspi.1: alias fck already exists omap2_mcspi.2: alias fck already exists edma.0: alias fck already exists edma.0: alias fck already exists edma.0: alias fck already exists bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3 musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1 omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz tps65910 1-002d: JTAGREVNUM 0x0 print_constraints: VRTC: print_constraints: VIO: at 1800 mV print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal print_constraints: VDD3: 5000 mV print_constraints: VDIG1: at 1800 mV print_constraints: VDIG2: at 1800 mV print_constraints: VPLL: at 1800 mV print_constraints: VDAC: at 1800 mV print_constraints: VAUX1: at 1800 mV print_constraints: VAUX2: at 3300 mV print_constraints: VAUX33: at 3300 mV print_constraints: VMMC: at 3300 mV tps65910 1-002d: No interrupt support, no core IRQ Advanced Linux Sound Architecture Driver Version 1.0.24. Bluetooth: Core ver 2.16 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Switching to clocksource gp timer musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) musb-hdrc musb-hdrc.0: dma type: pio musb-hdrc musb-hdrc.0: USB OTG mode controller at d081c000 using PIO, IRQ 18 musb-hdrc musb-hdrc.1: dma type: pio musb-hdrc musb-hdrc.1: MUSB HDRC host driver musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: MUSB HDRC host driver usb usb1: Manufacturer: Linux 3.2.0-gb02ab39 musb-hcd usb usb1: SerialNumber: musb-hdrc.1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected musb-hdrc musb-hdrc.1: USB Host mode controller at d081e800 using PIO, IRQ 19 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ 0.163330] 0.163330] 0.163604] 0.289825] 0.290069] 0.290130] 0.291046] 0.292083] 0.292083] 0.292175] 0.294677] 0.936767] 0.940795] 0.948486] 0.956146] 0.963806] 0.971405] 0.985046] 0.991302] 0.994842] 1.001281] 1.007720] 1.021636] 1.026641] 1.032775] 1.047943] 1.051300] 1.054595] 1.057678] 1.063323] 1.070068] 1.075622] 1.094909] 1.099822] 1.104858] 1.108917] 1.131958] 1.138153] 1.144104] 1.151153] 1.157928] 1.163421] 1.169067] 1.174346] 1.179595] 1.183715] 1.187896] 1.192291] 1.200073] 1.228668] 1.322204] 1.332458] 1.339447] 1.344085] 1.347473] 1.351104] 1.359893] 1.365509] 1.371490] 1.377960] 1.384429] 1.390899] 1.397705] 1.404113] 1.412231] 1.522521] 1.527130] 1.531127] 1.581939] 1.588409] 1.595733] 1.599304] 1.606719] 1.611358] RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. NetWinder Floating Point Emulator V0.97 (double precision) ashmem: initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 491 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 console [ttyO0] enabled omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 brd: module loaded loop: module loaded i2c-core: driver [tsl2550] using legacy suspend method i2c-core: driver [tsl2550] using legacy resume method at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write Detected a daughter card on AM335x EVM.. Unknown CPLD version found, falling back to 1.0A at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write Board name: A33515BB Board version: 1.2A SKU: SKU#01 The board is general purpose EVM in profile 0 Found invalid GP EVM revision, falling back to Rev1.1A da8xx_lcdc.0: alias fck already exists da8xx_lcdc da8xx_lcdc.0: GLCD: Found TFC_S9700RTWV35TR_01B panel TSC connected to beta GP EVM omap-gpmc omap-gpmc: GPMC revision 6.0 Registering NAND on CS0 omap_i2c.2: alias fck already exists omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz tsl2550 2-0039: standard operating mode tsl2550 2-0039: registering lightsensor-level input device input: lightsensor-level as /devices/virtual/input/input0 tsl2550 2-0039: support ver. 1.2 enabled davinci-mcasp.1: alias fck already exists omap_hsmmc.0: alias fck already exists omap_hsmmc.2: alias fck already exists am335xevm: bt init (stk) :sysfs entries created (stk) : debugfs entries created _regulator_get: 2-0018 supply Vdd not found, using dummy regulator _regulator_get: 2-0018 supply Vdd_IO not found, using dummy regulator lis3lv02d: 8 bits 3DLH sensor found input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input1 mtdoops: mtd device (mtddev=name/number) must be supplied omap2-nand driver initializing ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP) Creating 8 MTD partitions on "omap2-nand.0": 0x000000000000-0x000000020000 : "SPL" 0x000000020000-0x000000040000 : "SPL.backup1" 0x000000040000-0x000000060000 : "SPL.backup2" 0x000000060000-0x000000080000 : "SPL.backup3" 0x000000080000-0x000000260000 : "U-Boot" 0x000000260000-0x000000280000 : "U-Boot Env" 0x000000280000-0x000000780000 : "Kernel" 0x000000780000-0x000010000000 : "File System" OneNAND driver initializing CAN device driver interface CAN bus driver for Bosch D_CAN controller 1.0 davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 davinci_mdio davinci_mdio.0: detected phy mask fffffffe davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown PPP generic driver version 2.4.2 PPP BSD Compression module registered [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ 1.616271] 1.621643] 1.627777] 1.633758] 1.639617] 1.645843] 1.649261] 1.655242] 1.661132] 1.669494] 1.674713] 1.680969] 1.685943] 1.692077] 1.697387] 1.704223] 1.708801] 1.715209] 1.721008] 1.728027] 1.734222] 1.738037] 1.743377] 1.747344] 1.752929] 1.760742] 1.767852] 1.775390] 1.780548] 1.786926] 1.792175] 1.796112] 1.800811] 1.807464] 1.816253] 1.824768] 1.829650] 1.836578] 1.840545] 1.845550] 1.851531] 1.856658] 1.863128] 1.870513] 1.877075] 1.882110] 1.890930] 1.895568] 1.900573] 1.905487] 1.914489] 1.918884] 1.926422] 1.932281] 2.041656] 2.046508] 2.051483] 2.056427] 2.061828] 2.069335] 2.077148] 2.084808] 2.092498] 2.103485] 2.110656] 2.113800] 2.116790] 2.122070] 2.126708] 2.133422] 2.139129] 2.142700] 2.148071] 2.153106] PPP Deflate Compression module registered usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver dm9601 usbcore: registered new interface driver cdc_subset cdc_ncm: 04-Aug-2011 usbcore: registered new interface driver cdc_ncm usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems gadget: Mass Storage Function, version: 2009/09/11 gadget: Number of LUNs=1 lun0: LUN: removable file: (no medium) gadget: android_usb ready musb-hdrc musb-hdrc.0: MUSB HDRC host driver musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: MUSB HDRC host driver usb usb2: Manufacturer: Linux 3.2.0-gb02ab39 musb-hcd usb usb2: SerialNumber: musb-hdrc.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected mousedev: PS/2 mouse device common for all mice input: matrix-keypad as /devices/platform/matrix-keypad/input/input2 input: ti-tsc-adcc as /devices/platform/omap/tsc/input/input3 using rtc device, omap_rtc, for alarms omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 i2c /dev entries driver Linux video capture interface: v2.00 usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) input: lm75-temp as /devices/virtual/input/input4 lm75 2-0048: hwmon0: sensor 'tmp275' OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCI H4 protocol initialized Bluetooth: HCILL protocol initialized Bluetooth: Bluetooth Driver for TI WiLink - Version 1.0 cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver usbhid usbhid: USB HID core driver logger: created 256K log 'log_main' logger: created 256K log 'log_events' logger: created 256K log 'log_radio' logger: created 256K log 'log_system' usbcore: registered new interface driver snd-usb-audio _regulator_get: 2-001b supply IOVDD not found, using dummy regulator _regulator_get: 2-001b supply DVDD not found, using dummy regulator _regulator_get: 2-001b supply AVDD not found, using dummy regulator _regulator_get: 2-001b supply DRVDD not found, using dummy regulator asoc: tlv320aic3x-hifi <-> davinci-mcasp.1 mapping ok ALSA device list: #0: AM335X EVM oprofile: hardware counters not available oprofile: using timer interrupt. nf_conntrack version 0.5.0 (3930 buckets, 15720 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 [ 2.157745] [ 2.164367] [ 2.169006] [ 2.173461] [ 2.179565] [ 2.184753] [ 2.190093] [ 2.194000] [ 2.199554] [ 2.205017] [ 2.211303] [ 2.216339] [ 2.224334] [ 2.228851] [ 2.234497] [ 2.239318] [ 2.246002] [ 2.250305] [ 2.264068] [ 2.271148] [ 2.277648] [ 2.285064] [ 2.294342] [ 2.353729] [ 2.358978] [ 2.368347] [ 2.486907] [ 2.506530] [ 2.513427] [ 3.032287] [ 3.267639] [ 3.276763] [ 3.285278] [ 3.291992] [ 3.400970] [ 3.531524] [ 3.589935] [ 3.596130] [ 3.604156] [ 3.660644] [ 3.853668] [ 3.864135] [ 3.868560] [ 4.412902] [ 4.418304] [ 4.427032] [ 4.435302] [ 4.443572] [ 4.451812] [ 4.460083] [ 6.433197] root@android:/ can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) can: broadcast manager protocol (rev 20090105 t) Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 Registering the dns_resolver key type VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 ThumbEE CPU extension supported. mux: Failed to setup hwmod io irq -22 Power Management for AM33XX family Trying to load am335x-pm-firmware.bin (60 secs timeout) Copied the M3 firmware to UMEM omap_hwmod: wkup_m3: wkup_m3: hwmod data error: OMAP4 does not support st_shift clock: disabling unused clocks to save power Detected MACID=d4:94:a1:52:d7:ed input: gpio-keys as /devices/platform/gpio-keys/input/input5 omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) Waiting for root device /dev/mmcblk0p2... mmc0: new SDHC card at address bea8 mmcblk0: mmc0:bea8 SD04G 3.69 GiB mmcblk0: p1 p2 p3 mmc1: card claims to support voltages below the defined range. These will be ignored. mmc1: queuing unknown CIS tuple 0x91 (3 bytes) mmc1: new SDIO card at address 0001 (stk) :line disc installation timed out EXT4-fs (mmcblk0p2): recovery complete EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. Freeing init memory: 236K init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead. init: cannot open '/initlogo.rle' Disabling lock debugging due to kernel taint Compat-wireless backport release: compat-wireless-2011-12-05-1-g84dbe2c Backport based on wl12xx.git v2.6.39-1328-g0890f48 cfg80211: Calling CRDA to update world regulatory domain init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' android_usb: already disabled adb_bind_config cfg80211: World regulatory domain updated: cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) adb_open #